Accessories
LokPilot 5 micro DCC Direct Kato USA »Blank decoder«, gauge: N The LokPilot 5 micro DCC Direct Kato USA has been specially developed for installation in N scale locomotives of the Kato USA brand. This decoder can be easily installed in most American diesel locomotives of this manufacturer instead of the analog board installed as standard. The LokPilot 5 micro DCC Direct Kato USA with its dimensions of 60.0mm x 10.1mm is a pure DCC decoder. Modes The LokPilot 5 micro DCC Direct Kato USA is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully to a suitable digital center. It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokPilot 5 micro DCC Direct Kato USA Decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or DC voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An AUTOMATIC ABC commuter train allows automatic commuting between two stations. The LokPilot 5 micro DCC Direct Kato USA can be used on analog DC. The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions Despite its compact dimensions, the LokPilot 5 micro DCC Direct Kato USA is equipped with an enormous number of function outputs. Two directly soldered SMD LEDs are designed for front and rear head lighting. For older models, two 3mm LEDs can be soldered and controlled separately (one at each end resistor protected). Three further powered function outputs (non-resistor protected) are also available. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 micro DCC Direct Kato USA has a variable PWM clock frequency from 10kHz to 50kHz, which ensures super-quiet operation, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokPilot 5 micro DCC Direct Kato USA decoder delivers up to 0.9A motor power. Operational reliability A PowerPack can be connected to the LokPilot 5 micro DCC Direct Kato USA on request to bridge dirty rail sections using the logic level output AUX6. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 59741 LokPilot 5 micro DCC Direct Kato USA »Blank decoder«, gauge: N
In stock: 3 on the shelf, shipped within 1-3 days
LokPilot 5 micro DCC/MM/SX, 6-pin Direkt, gauge N, TT The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm) that it can be used even in very small locomotives Nominal sizes Z, N or TT can accommodate. Nevertheless, functionality and robustness were not spared compared to the larger versions. LokPilot 5 micro decoders are offered with all common interfaces. The versions with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but they also speak for the mfx®-compatible M4 protocol. Modes The LokPilot 5 micro is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The Next18 and PluX16 variants also allow automatic registration to mfx®-compatible control centers thanks to the M4 protocol. All 32 possible function keys are offered here. The LokPilot 5 micro decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC trains. The versions with Next18 or PluX16 can also be used on analog AC systems. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. That is why we have equipped the LokPilot 5 micro with an astonishing number of function outputs. The variants with 6-pin or 8-pin wiring harness offer 4 amplified function outputs with 180mA output current each as well as two logic level outputs for servos or Susi. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. motor control The engine control of the LokPilot 5 micro has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 0.75A motor current, the LokPilot 5 micro decoder provides enough juice for the intended application scenarios. Operational safety On request, a PowerPack can be connected to the LokPilot 5 micro to bridge dirty rail sections. Protection Of course, the motor output and the function outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59810 LokPilot 5 micro DCC/MM/SX, 8-pin NEM652, gauge N, TT 59814 LokPilot 5 micro DCC/MM/SX/M4, PluX16, gauge N, TT 59816 LokPilot 5 micro DCC/MM/SX, 6-pin NEM651, gauge N, TT 59817 LokPilot 5 micro DCC/MM/SX, 6-pin Direkt, gauge N, TT 59818 LokPilot 5 micro DCC/MM/SX/M4, Next18, gauge N, TT 59837 LokPilot 5 micro DCC/MM/SX, 6-pin Direct angled, gauge N, TT
In stock: 3 on the shelf, shipped within 1-3 days
The FALLER micro cable bulbs (12-16 V, AC/DC, 35 mA) are suitable for the ideal lighting of all fairground booths and rides in the colours:
In stock: 3 on the shelf, shipped within 1-3 days
Neat wiring! Blue low-voltage distribution board with 2 x 10 sockets, including 10 blue plugs, 2.5 mm.
In stock: 3 on the shelf, shipped within 1-3 days
For NEM 362 coupling socket. Content: 50 pc./pack.
In stock: 3 on the shelf, shipped within 1-3 days
Universal Oiler This practical tool for professionally lubricating models. One drop per lubrication point is sufficient! Universal application for: locomotive axle bearings, wagon wheel set bearings, sliding bolts and sliding guides of steam locomotive controls, etc. High viscosity – for universal applications – also retroactive oiling of motor bearings Thermally highly resistant synthetic oil for sintered metal bearings Compatible with plastics, good corrosion protection for steel and bronze bearings
In stock: 3 on the shelf, shipped within 1-3 days
Uncoupling track with electric drive. Length 111 mm.
In stock: 3 on the shelf, shipped within 1-3 days
Standard coupling with spiral centre spring and cover plate.
In stock: 3 on the shelf, shipped within 1-3 days
Standard plug-in coupling. Simply pushes into the coupling socket.
In stock: 3 on the shelf, shipped within 1-3 days
Bogie holding pins, black
In stock: 3 on the shelf, shipped within 1-3 days
Connection adapter, for example for connecting loads such as lights to a switched-mode power supply with a 4-pin high-current mini-DIN plug.
In stock: 3 on the shelf, shipped within 1-3 days
For converting Märklin locomotives with a built-in universal / field coil motor. The märklin LokDecoder Allstrom supports the mfx, MM1, MM2 and DCC digital formats. Particularly powerful function outputs for old Telex couplers, light bulbs and smoke generators. The classic unregulated running characteristics under different load conditions are retained on the "Old- und Youngtimer" locomotives retrofitted with this decoder.
In stock: 3 on the shelf, shipped within 1-3 days
For converting Märklin/Trix H0 locomotives with a built-in high-efficiency motor or other DC motors. The märklin SoundDecoder mSD3 has a soldered-on wiring harness. The märklin SoundDecoder mSD3 supports the mfx, MM1, MM2 and DCC digital formats. A plug for NEM-652 interfaces, to be soldered on yourself, is included. Preset sound of a steam locomotive.
In stock: 3 on the shelf, shipped within 1-3 days
For converting Märklin/Trix H0 locomotives with a built-in high-efficiency motor or other DC motors. The märklin SoundDecoder3 has a soldered-on wiring harness with an 8-pin NEM interface plug, for retrofitting many locomotives with a corresponding NEM interface and locomotives with limited space. The märklin SoundDecoder3 supports the mfx, MM1, MM2 and DCC digital formats. Preset sound of an electric locomotive.
In stock: 3 on the shelf, shipped within 1-3 days
Model The Märklin 7102 cable (brown) is the ideal solution for clean and reliable wiring of your model railway layout. With a length of 10 metres, a 0.19 mm² cross-section and single-core construction, it is perfectly suited to common return leads, accessories or lighting – universally usable for all gauges. Single-core. Brown. 10 m. Cross-section 0.19 mm². Highlights 10 m connecting cable in brown, single-core, 0.19 mm² cross-section Universally usable for all gauges and systems (analogue & digital) Ideal for common return leads as well as accessories, points and lighting Flexible and long-lasting insulation for easy laying even on complex layouts Clear colour coding for tidy and safe wiring
In stock: 3 on the shelf, shipped within 1-3 days
3-pole cable for the connection between the 74492 point motor and the 72752 control panel from the Start up range. Length: 1.80 m.
In stock: 3 on the shelf, shipped within 1-3 days
Model Pack of 10 pieces. Note The plugs and sockets cannot be combined with the earlier version (pack item no. 7130). The sockets fit with limitations in the jacks of the earlier version of control panels and switch panels. Many controllers and decoders in the Märklin range have today already been converted to the new standard.
Content: 10 pc. (CHF 0.49 / 1 pc.)
In stock: 3 on the shelf, shipped within 1-3 days
Model Pack of 10 pieces. Matching the standard plugs and sockets from the 71400 assortment. Note The plugs and sockets cannot be combined with the earlier version (pack item no. 7130). The sockets fit with limitations in the jacks of control panels and switch panels of the earlier version. The controllers and decoders in the current Märklin range have been converted to the new standard.
Content: 10 pc. (CHF 0.49 / 1 pc.)
In stock: 3 on the shelf, shipped within 1-3 days
Highlights Optimum traction: increases grip and ensures stable power transmission on Märklin H0 locomotives High-quality material: long service life and reliable performance Practical set of 10: easy replacement for several vehicles or as a replacement stock Product description The Märklin 7154 traction tyres (10 pieces) increase the tractive effort and improve the traction of your Märklin H0 locomotives. They are made of high-quality material, are easy to fit and ensure reliable power transmission, even with heavy trains or on gradients. Ideal for replacing worn traction tyres and for even performance on your model railway. Inside diameter approx. 8 mm.
Content: 10 pc. (CHF 0.57 / 1 pc.)
In stock: 3 on the shelf, shipped within 1-3 days
Separable close coupler with a single-pole electrical connection for lighted express coaches. Suitable for the prepared coaches 26.4 cm, 27 cm and 28.2 cm long when the 73400 interior lighting is installed. One coach in the train consist requires a 73404, 73405 or 73406 pickup shoe. Contents: 2 close coupler heads for standard coupler pockets with contacts, 2 contact sets for the coupler drawbars, 1 common return spring for the bogie, 2 connecting cables and installation instructions. Reliable connection with latching contacts. Coupling and uncoupling by hand on the layout is possible; they will also couple with regular close couplers without an electrical contact.
In stock: 3 on the shelf, shipped within 1-3 days
Model Separable close coupler with a single-pole electrical connection for lighted express coaches. Also suitable for vehicles with a lower buffer height in accordance with NEM 303. Suitable for the prepared coaches 26.4 cm, 27 cm and 28.2 cm long when the 73400/73401 interior lighting is installed. One coach in the train consist requires a 73404, 73405 or 73406 pickup shoe. Contents: 2 close coupler heads for standard coupler pockets with contacts, 2 contact sets for the coupler drawbars, 1 common return spring for the bogie, 2 connecting cables and installation instructions. Reliable connection with latching contacts. Coupling and uncoupling by hand on the layout is possible; they will also couple with regular close couplers without an electrical contact. Highlights Current-conducting close coupler heads for vehicles with a lower buffer height
Content: 2 pc. (CHF 7.45 / 1 pc.)
In stock: 3 on the shelf, shipped within 1-3 days
Model For switching a maximum of 4 points. Automatic feedback of the position by means of LEDs is possible when using the 74492 point motor. A 4-conductor cable with plugs for connecting several panels is included. Note To extend the cable connection between the point control panel and the point motor we recommend item 71054.
In stock: 3 on the shelf, shipped within 1-3 days
Model Universal circuit board with several LEDs, suitable for most of the coaches in the Märklin H0 programme. One 73400 is required for a short coach (e.g. Langenschwalbacher), two for long coaches (e.g. UIC-x with 28.2 cm). The circuit boards can be plugged together several times over or shortened. Mounting material is included. For the electrical connection, the separate power feed 73404, 73405 or 73406 or the current-conducting coupler 72020 with the common return spring 72050 is required, depending on the type of coach. Highlights A cosy feel in the coach: dimmed LEDs Note The 73400 (dimmed light for older eras) and 73401 (white light for more modern coaches) interior lighting kits are technically interchangeable with one another.
In stock: 3 on the shelf, shipped within 1-3 days
Model For the 73400 interior lighting. With a symmetric pickup shoe and a common return spring. Note The combination of 2 x 73400 + 1 x 73405 can replace the previous 73150 interior lighting.
In stock: 3 on the shelf, shipped within 1-3 days