Digital DCC electronics
YaMoRC, DCC electronics for your layout
Command station, booster, accessory decoders and feedback modules: products made by modellers, for modellers.
- 26items in the shop
- DCCthe control system
- 3feedback buses: LocoNet, s88N, R-Bus

What makes YaMoRC
- By modellers, for modellers: that is the motto of YaMoRC, a brand of Drenth Design & Consulting B.V. in Apeldoorn, the Netherlands. All products are designed by Karst Drenth.
- Digital control first: DIGITAL is the first range the brand has launched: everything needed to run a DCC layout.
- Feedback for every bus: 16-input modules for LocoNet with RailCom, s88N and R-Bus, with or without current sensors.
- From turntable to reversing loop: turntable control with an adapter for Märklin and Roco turntables, a LocoNet RailCom reversing loop module, decoders for solenoid or servo point motors.
The YaMoRC families
Layout control
Points and feedback
All YaMoRC items
Specially designed to cope with, high-current, solenoid point-motors, the YD8008 is our 8-fold solenoid decoder with intelligent CDU. It presents the following features: - Eight independent 9.5Amp solenoid outputs - Smart, 9400 uF CDU, monitoring charge levels for safe and powerful switching - Only 380 mA power consumption during charging - Very simple basic-setup (base address), by pressing the programming button and switching the desired turnout address - No complicated CV settings. - Clear-text configuration based upon our new ES-Link technology. With our YD9101-Config or YD7100-Command, configuration can be done via built-in web interface. No need for PC-software or Phone/Tablet Apps ! - or - when using the classic Windows PC interface, the YD9100 config-USB-stick as well as our YD6016LN can provide the configuration. - Eight address to output mappings, each mapping can a free choice address which can switch any and every output - Sequential output activation based upon pulse time and CDU charge level. - CDU startup delay adjustable to prevent tripping short circuit protection in boosters - Very modest power supply requirements. Even for SEEP/Gaugemaster motors a 15V/500mA wall wart is more than enough. - Not suitable for motorized point motors. For these motors, use our YD8116. This also counts for MTB point motors. - For two-wire solenoid motors, like Kato, adapter YD6940 should be used.
In stock: 2 on the shelf, shipped within 1-3 days
Our classic s88N feedback module with current sensing inputs It presents: - 16 current-sensing detectors, arranged in two independent blocks of 8, each with their own Common - 2 Amp continuous current per detector, 8 Amps in total combined over the 16 detectors on the whole module - 5 Amp short duration overload (100ms) capable per detector. - 1-1.5mA current sensitivity - Capacitive input filter on every input, to suppress noise on long cables and track-sections - Configurable on- and off-delay setting for each input for optimal de-bouncing in case of non optimal wheel-track contact - ES-OUT-Link for direct connection to an ES-Link-master - ES-IN-Link connection to other ES-Link enabled modules for module-configuration - Standard s88N connections over RJ45 connectors and ethernet patch cables - Firmware updatable and settings configurable over ES-Link - Power supply directly from ES-Link or s88 bus
In stock: 1 on the shelf, shipped within 1-3 days
The YaMoRC solution for practically all polarity reversing tasks. It presents the following features: - 2-sensor short-circuit free operation. - alternative short-circuit detection mode - follow polarity with external (LocoNet) occupation feedback - follow polarity with turnout at entry - via LocoNet - via DCC - set turnout at exit - 100% solid-state, no relays - RailCom Block-, Address and Rail-Direction Report - LocoNet occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity - ES-Link occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity - ES-Link configuration - Firmware updatable - Current Ratings: - 2A - Continuous Operation - 2.5-2.75A Short Circuit Detection treshold. For reversing as well as short circuit shurdown. - 3.5A - Maximum Current during maximum 5 Seconds ( Command Station/Booster should switch off in this time )
In stock: 1 on the shelf, shipped within 1-3 days
The YD7460-15 is a switched-mode power supply with 15 V DC voltage and 4 A output for YaMoRC digital central stations and boosters, for example YD7010 or YD7403. According to the manufacturer, the 15 V version is suitable for Gauge TT and smaller gauges. The power supply is double-insulated (Protection Class 2), short-circuit and overload protected, and does not heat up when the central station or booster is idle. It has a compact design and a two-core low-voltage cable instead of a thin coaxial cable. It was manufactured in accordance with the manufacturer's specifications to match the YaMoRC boosters and central stations. Output 15 V DC, 4 A Protection class 2 Short-circuit and overload cut-off
In stock: 1 on the shelf, shipped within 1-3 days
The YD6016ES-GND is a feedback module for the s88N bus with sixteen logic-based inputs. The state of push buttons, switches, or reed contacts is detected against the common connection C. The inputs are divided into two groups of eight, each input has a capacitive input filter, and the on and off delay is adjustable per input. Connection is via RJ45 sockets and standard Ethernet patch cables, alternatively via ES-Link, which also handles firmware updates and configuration. The module is designed for 5 V on the s88 bus and must not be operated on control units with 12 V on the s88N connection. 16 inputs in two groups of 8 For push buttons, switches, reed contacts Powered via ES-Link or s88 bus Housing 84 x 88 x 22 mm
On order, shipped within 3-8 days
Our standard current-sensing feedback module with LocoNet Interface It presents: - 16 current-sensing detectors, arranged in two independent blocks of 8, each with their own Common - 2 Amp continuous current per detector, 8 Amps in total combined over the 16 detectors on the whole module - 5 Amp short duration overload (100ms) capable per detector. - 1-1.5mA current sensitivity - Capacitive input filter on every input, to suppress noise on long cables and track-sections - Configurable on- and off-delay setting for each input for optimal de-bouncing in case of non optimal wheel-track contact - Every input individually configurable for various actions like feedback, turnout toggle, turnout throw, turnout close - Every input individually configurable for feedback- or turnout-address - ES-IN-Link for direct connection of up to 5 additional YD6016ES modules (effectively creating a 96 input LocoNet module) - ES-IN-Link connection to other ES-Link enabled modules for module-configuration - ES-IN-Link connection to YD9101 for web-based configuration - USB connection with one Virtual COM ports for the YD.Command** protocol - Firmware updatable over USB - Power supply directly from LocoNet-T or -B ( or USB for easy configuration and updating on a PC ) **)Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.
On order, shipped within 3-8 days
Our standard ground-input feedback module with LocoNet Interface with: - 16 inputs, switching against Ground ( both "C" terminals ) - Capacitive input filter on every input, to suppress noise on long cables - Configurable on- and off-delay setting for each input for optimal de-bouncing of pushbuttons, switches, reed contacts - Every input individually configurable for various actions like feedback, turnout toggle, turnout throw, turnout close - Every input individually configurable for feedback- or turnout-address - ES-IN-Link for direct connection of up to 5 additional YD6016ES modules (effectively creating a 96 input LocoNet module) - ES-IN-Link connection to other ES-Link enabled modules for module-configuration - ES-IN-Link connection to YD9101 for web-based configuration - USB connection with one Virtual COM ports for the YD.Command** protocol - Firmware updatable over USB - Power supply directly from LocoNet-T or -B ( or USB for easy configuration and updating on a PC ) **)Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.
On order, shipped within 3-8 days
The YD6016LN-RC is a feedback module for LocoNet with sixteen inputs and sixteen local RailCom detectors. Up to four locomotive addresses are detected per section via RailCom Channel 1 or Channel 2 and reported to the central station. An additional global detector monitors the track output. For vehicles without RailCom, the inputs also function as current sensors. The module supports reading out locomotive and accessory decoders via POM, as well as reporting QoS, speed, and container fill level. Power is supplied via the track input, with the connection to LocoNet T or B. An extension to 96 feedback units is possible via s88N-IN or ES-IN Link. Address range 1 to 4096 Occupancy detection from 3 mA 2 A per input, 4 A total Configuration and firmware update via USB
On order, lead time to be confirmed
Our standard current-sensing feedback module with RBus / XBus Interface It presents: - 16 current-sensing detectors, arranged in two independent blocks of 8, each with their own Common - 2 Amp continuous current per detector, 8 Amps in total combined over the 16 detectors on the whole module - 5 Amp short duration overload (100ms) capable per detector. - 1mA current sensitivity - Capacitive input filter on every input, to suppress noise on long cables and track-sections - Configurable on- and off-delay setting for each input for optimal de-bouncing in case of non optimal wheel-track contact - Every input individually configurable for various actions like feedback, turnout toggle, turnout throw, turnout close - Every input individually configurable for turnout-address - ES-IN-Link for direct connection of up to 4 additional YD6016ES modules (effectively creating a 80 input RBus module) - ES-IN-Link connection to other ES-Link enabled modules for module-configuration - ES-IN-Link connection to YD9101 for web-based configuration - USB connection with one Virtual COM port for the YD.Command** protocol - Firmware updatable over USB - Power supply directly from RBus / XBus ( or USB for easy configuration and updating on a PC ) - Experimental: XpressNet feedback reporting. This enables more then 160 feedbacks on the white z21® command stations. **)Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.
On order, shipped within 3-8 days
The YD6901ES-LINK is the connector that establishes the ES-Link connection between two modules mounted directly next to each other. It is plugged into the ES-Link connections of the two modules, for example between a feedback module YD6016LN and a YD6016ES or a point decoder. This connection is used to expand feedback modules, configure modules with ES-PGM Link, and supply them with firmware updates. For greater distances between the modules, the adapter YD6902ES-EXT with an RJ45 cable is provided. A connector of this type is also included with the configuration stick YD9100. Connector for ES-Link between two modules Contents: 5 pieces
On order, shipped within 3-8 days
The YD6902ES-EXT is an adapter set used to establish the ES-Link connection between two modules via a standard CAT5 patch cable. It is used when the modules are not mounted directly next to each other and the YD6901ES-LINK connector is insufficient. The set consists of one adapter for the ES-OUT-Link connection and one adapter for the ES-IN-Link connection, each with an RJ45 socket. This allows, for example, the configuration stick YD9100 to be connected to a more distant module. ES-Link via CAT5 patch cable Includes an adapter for ES-IN Link and ES-OUT Link RJ45 sockets
On order, shipped within 3-8 days
The YD6940 is a set of two adapters for point motors that require polarity reversal to switch, so-called motor or stall motors. The adapter is used with the YD8116 switching decoder, for example for drives from Conrad, Hoffmann, Tillig, Fulgurex, Tortoise and Cobalt Analog. It is also required for Kato two-wire solenoid point motors on the YD8008 and YD8044 point decoders. It is also recommended for two-wire motor drives on the YD8248 servo decoder. Each adapter handles currents up to 3 A. Contents: 2 adapters For motor drives with polarity reversal on the YD8116 For Kato magnetic drives on the YD8008 and YD8044 Rated up to 3 A
On order, shipped within 3-8 days
The YD6942 is a set of two adapters that allow common-cathode (negative return) light signals to be operated with the YD8116 switching decoder. The adapter has one side for connection to the decoder and one side for connection of the signal, each with screw terminals. A 270 Ohm resistor is fitted on the adapter. This limits the output current to approximately 50 to 70 mA, depending on the supply voltage. Contents: 2 adapters For signals with a common cathode on the YD8116 Integrated 270 Ohm resistor Current limited to approximately 50 to 70 mA
On order, lead time to be confirmed
Building on the immense succes of our YD9401 upgrade for the DR5000, we decided to bring a complete Command Station, the YD7010, that includes the proven YD7001 technology and YD9401 Network Module. The command station is based on the technology used in our YD7001-E, but with a completely new designed mainboard, with improved component choice and PCB layout to render robustness and extended functionality. Of course the YD7010 comes with our YD9401 is pre-installed. Further we improved some visual and usability aspects: Different colors for the RJ connectors which were easy to confuse when they were all gray. Now the XBus and Network sockets have different colors to the ES-Link/s88N, LocoNet and BBus connectors. On the front we moved the GO- and STOP-LEDs to be in-line with all LEDs and that prevents touching and/or damaging the LEDs when operating the pushbuttons. On the back we moved the RS-Bus and Program-Track terminals into one 4-way block. This effectively prevents the terminals of turning and, worst case, shearing off ! The product placement of the YD7010 in our portfolio is meant to be an Entry Level, yet very complete and versatile DCC command station. A summary of the presented features: - Unique DCC signal generator: – With priority control and interleaved packet generation. – Changes sent by any interface are directly being reflected to the track. – Generates RailCom Cut-Out. - 3 A integrated Booster - Operating voltage range from 15 – 19 VDC. Giving a track-voltage of 13.8 – 17.8 Volts. That means safe for your N-scale equipment and powerful for H0. - Multiple Model Railroad compatible Interface Busses: – LocoNet, the world standard set by Digitrax Inc. – XpressNet, from the inventor of DCC: Lenz – Good old S88 signalling, fully compatible with ES-IN-Link by use of our YD6902ES-EXT adapters. - USB interface for three virtual COM-ports: – YD.Command ** – LocoNet – XpressNet The USB connection can also be used to update the YD7010`s firmware - Full network capabilities: – WiFi Access Point, gives direct access to smartphones, tablets and handheld controllers – 100baseT RJ45 wired network socket, connect and bind to your home network and reliably connect your PC software - By means of the built in YD9401 Module which provides: – 6 different but SIMULTANEOUS usable network protocols on WiFi and LAN: * XpressNet-LAN, * Z21®, * LocoNet Binary, * LocoNet LBServer, * JMRI: WiThrottle * YD.Command ** - Booster Interface by LocoNet-B with strong, 800mA LocoNet RailSync signals - Handcontroller, feedback modules etc. interface by LocoNet-T with strong, 800mA 12VDC power supply - Powerful 1 Amp XpressNet supply - Roco R-BUS compatible feedbacks on XpressNet socket - Roco B-BUS for compatible boosters on RJ10 socket - Lenz RS-BUS compatible feedbacks - Infra-Red sensor for the use of IR-based remotye controllers like the Uhlenbrock IRIS or the Piko DigiFern - Clear LED indicators - Programming: – POM write – Service Mode ( programming track ) – ES-Link capable modules like YD8044, YD8008, YD8116, YD6016ES, YD7403 - Additional extra purchasable , quality made, YaMoRC spec, switch mode power supply with choise of: – 15V fixed / 4 A – 18V fixed / 3.3A **) Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.
On order, shipped within 3-8 days
The YD7403 is a pure DCC booster with 3.5 A peak current and 2.75 A continuous current, which passes the RailCom cutout of the input signal to the output. The LocoNet B, Roco B-Bus, CDE and Track Sniffer inputs are galvanically isolated, the active signal source is automatically selected and indicated by an LED. The booster can be switched on and off and reversed via a DCC accessory address and reports its status via LocoNet. Short circuits are reported via LocoNet, CDE or B-Bus. Configuration is carried out via ES-PGM Link, for example with the YD9100. The power supply is provided by a DC voltage power supply unit with 15 to 19 V. Output 3.5 A peak, 2.75 A continuous Input 15 to 19 V DC, max. 60 W Short-circuit proof Body 84 x 88 x 22 mm
On order, shipped within 3-8 days
The YD7460-18 is a switched-mode power supply providing 18 V DC voltage and 3.3 A for YaMoRC digital central stations and boosters, for example the YD7010 or YD7403. For the turntable control YD7652, it is recommended as the power supply in the manual. The power supply is double-insulated (protection class 2), short-circuit and overload protected, and does not heat up when the central station or booster is idling. It has a compact design and a two-core low-voltage cable instead of a thin coaxial cable. It was manufactured in accordance with the manufacturer's specifications to suit the YaMoRC boosters and central stations. Output 18 V DC, 3.3 A Safety class 2 Short-circuit and overload protection
On order, shipped within 3-8 days
Let your Fleischmann, Roco, Märklin or DIY turntable being operated fully digitally Our specialized TurnTable Controller. It presents: - Full, regulated, Motor-Control, with acceleration and dynamic braking. - Supports DCC and Motorola turnout commands - Supports DCCext "aspect" driven commands. - LocoNet, for feedback in- and output and turnout-command input - Control protocols: Fleischmann (TurnControl) & Märklin (7686) - Built-in DCC generator for "Profi" variant ( Decoder in bridge ) - RailCom detector for the bridge - Occupance sensor for the bridge - Automatic, configurable polarity switching per entry - Three-button manual controls - ES-LINK-IN for extra position-sensor modules and the YD7652EX, extender for Märklin and Roco Turntables It currently supports: - Fleischmann H0 6052 (Brass track) - Fleischmann H0 6152 (Profi track) = Roco 6152 - Fleischmann H0 6651 (New-Silver track) - Fleischmann H0 6652 (3-rail & 2-rail) = Roco 665201 - Fleischmann H0 6154 (Profi track, small bridge) = Roco 6154 - Fleischmann N 9152 - Roco H0 42615 - Roco TT 35900 - Märklin H0 7286 Power: - Input 10–19 V DC (16–19 V DC recommended), max. 60 W Recommended Upgrade: - Replacement motor from SB-Modellbau Modes, modules and turntables: Turntable(s) Mode Module(s) Turntable remains unmodified Basic YD7652 6052, 6152, 6651, 6652 (2-rail), 6154, 9152, 35900 These turntables make a clicking sound while turning in Basic mode, due to the way the positions are counted. These turntables can be connected directly to the YD7652, no further modules needed. Turntable remains unmodified Basic YD7652 + YD7652EX Märklin H0 7286 These turntables make a clicking sound while turning in Basic mode, due to the way the positions are counted. These turntables can be connected directly to the YD7652EX. The YD7652EX is connected to the YD7652 with the TURN-Link and ES-Link adapter boards. Turntable remains unmodified Basic YD7652 + YD7652EX 6652/Roco 665201 (3-rail) These turntables make a clicking sound while turning in Basic mode, due to the way the positions are counted. These turntables can be connected to the YD7652EX with the 6652 adapter installed. The YD7652EX is connected to the YD7652 with the TURN-Link and ES-Link adapter boards. Turntable remains unmodified, must be set in "1" mode Basic YD7652 + YD7652EX Roco H0 42615 These turntables make a clicking sound while passing an exit, due to the mechanical sensor on the bridge-end. These turntables can be connected to the YD7652EX with the Roco-Edge adapter installed. The YD7652EX is connected to the YD7652 with the TURN-Link and ES-Link adapter boards. Turntable remains unmodified Basic-Plus YD7652 + YD7652ES 6052, 6152, 6651, 6652 (2-rail), 6154, 9152, 35900 These turntables can be controlled in such a way, that the position of the bridge is sensed. And can thus turn without the need for counting the positions and in that way turn without clicking sound. These turntables can be connected directly to the YD7652. For the position sensing, one or more YD7652ES are needed. Turntable bridge needs installation of a DCC Loco-Decoder Profi-Plus YD7652 + YD7652ES 6052, 6152, 6651, 6652 (2-rail), 6154, 9152, 35900 The Profi mode relies on the fact that the bridge motor is controlled by a loco-decoder, the bridge latch by a function output of that decoder. The YD7652 will then output a DCC signal on it's motor connections. Multiple decoders can be built into the bridge. These turntables can be connected directly to the YD7652. For the position sensing, one or more YD7652ES are needed. Modes, modules and turntables
On order, shipped within 3-8 days
The YD7652ES-OPTO is the position sensor module for the turntable control YD7652. It detects the position of the turntable platform via the track connections, allowing the control system to know the position without counting the track connections. The lock is only disengaged once, and the platform rotates without clicking to the selected track. One module processes up to 12 track connections; if there are more connections, an additional YD7652ES is connected. The connection to the YD7652 is made via ES-Link. No modifications to the turntable are required, as all track connections are connected to the module on both sides. For turntable control YD7652 Up to 12 track connections per module Connection via ES-Link For Fleischmann 6052, 6152, 6154, 6651, 9152 and Roco 35900
On order, shipped within 3-8 days
The YD7652EX-TURN is an extension of the turntable controller YD7652 for connecting turntables from Märklin (H0 7286) and Roco (H0 42615). The turntable type is set using a link plug. The module contains an 8-bit sensor module for the signals from the Roco and Märklin turntables and passes the ES-Link through. The contents supplied include the RocoEdge adapter, the TURN-Link plug, and the ES-Link plug, which are used to connect the module to the YD7652. The module is also required for the Fleischmann/Roco turntable 6652 or 665201 in 3-rail operation; the necessary plug for this is available from the retailer on request. For Märklin H0 7286 and Roco H0 42615 Turntable type via plug-in bridge Including RocoEdge adapter, TURN-Link and ES-Link bridge
On order, shipped within 3-8 days
Specially designed to cope with, high-current, solenoid point-motors, the YD8044 is our 4-fold solenoid decoder with CDU and Frog Supply. It presents the following features: - Four independent 9.5Amp solenoid outputs - Smart, 9400 uF CDU, monitoring charge levels for safe and powerful switching - Only 380 mA power consumption during charging - Frog polarization through a 2 Amp relay which switches together with the solenoid outputs - Very simple basic-setup (base address), by pressing the programming button and switching the desired turnout address - No complicated CV settings. - Clear-text configuration based upon our new ES-Link technology. With our YD9101-Config or YD7100-Command, configuration can be done via built-in web interface. No need for PC-software or Phone/Tablet Apps ! - or - when using the classic Windows PC interface, the YD9100 config-USB-stick as well as our YD6016LN can provide the configuration. - Four address to output mappings, each mapping can a free choice address which can switch any and every output - Sequential output activation based upon pulse time and CDU charge level. - CDU startup delay adjustable to prevent tripping short circuit protection in boosters - Very modest power supply requirements. Even for SEEP/Gaugemaster motors a 15V/500mA wall wart is more than enough. - Not suitable for motorized point motors. For these motors, use our YD8116. This also counts for MTB point motors. - For two-wire solenoid motors, like Kato, adapter YD6940 should be used.
On order, shipped within 3-8 days
The YaMoRC solution for switching and signaling: our 16-fold signal/switching decoder. It presents the following features: - Sixteen independent 2.5Amp MOSFET outputs - Max 5 Amp combined current - Very simple basic-setup (base address), by pressing the programming button and switching the desired turnout address - No complicated CV settings. - Clear-text configuration based upon our new ES-Link technology. With our YD9101-Config or YD7100-Command, configuration can be done via built-in web interface: No need for PC-software or Phone/Tablet Apps!. - or - when using the classic Windows PC interface, the YD9100 config-USB-stick as well as our YD6016LN can provide the configuration. - All of the 16 outputs are freely configurable from 16x simple on-off to complex and elaborate signals with up to 8 LEDs/lamps - Each defined device (signal, switch, turnout) can have its own address - Devices can be operated by the new DCCext standard or conventional turnout DCC-commands (throw/close) - Numerous predefined signal definitions for Dutch, German (H/V, Ks and Form) British and Swiss prototypical signals - Signals can include fading (Bulbs emulated in case of LEDs) dark-phase inclusion, black-out based on previous signal’s state - Outputs can be time-limited e.g. for light coil-motors - Settable night-dimming for the complete decoder, with configurable address / decoder - Very suitable for motorized point motors. - Not suitable for solenoid point motors. For these motors, use our YD8008/YD8044. - For two-wire motorized point motors, like Conrad; Hoffmann; Tillig; etc. adapter YD6940 should be used. How to configure the YD8116 with Viessmann signals and ECoS
On order, shipped within 3-8 days
The YD8248 is a DCC decoder for RC servos with a throw of 90° or 180°; linear and continuous servos are also controlled. Four servos can be connected directly from the factory, and with two YD8291 expansion modules, up to twelve can be used. Eight switching outputs are pre-assigned for light signals from the factory and can be used for common crossing polarisation with the YD8290 expansion. The servos can also be controlled without a digital central station using push buttons or potentiometers via eight digital inputs and four analogue inputs. The starting address is assigned using the programming button, and addresses 1 to 8 are pre-assigned from the factory. Further configuration is carried out via ES-PGM Link. It is not intended for motorised point motors. 4 servo outputs, expandable to 12 8 switching outputs, short-circuit-proof up to 2.5 A Address range 1 to 2048 Supply 12 to 19 V DC recommended
On order, shipped within 3-8 days
The YD8290 is a relay expansion adapter for the servo decoder YD8248. It is connected to the switching outputs of the YD8248 and provides four relays. The relays can be used for the polarity of the common crossing of four points, one relay per point, or in pairs for two points, with the common crossing de-energised during the servo movement. The four relays can also be used for other switching tasks or a combination thereof. Depending on the use, adjustments to the configuration of the YD8248 may be required. 4 relays Relay voltage 5 V Contact current max. 2 A For servo decoder YD8248
On order, shipped within 3-8 days
The YD8291 is a servo expansion adapter for the servo decoder YD8248. Up to four additional RC servos can be plugged in and controlled to each YD8291. By using two YD8291 adapters, a total of twelve servos can be operated on one YD8248. The adapter is connected to the switching outputs of the YD8248; depending on the use, adjustments in the decoder configuration may be necessary. 4 additional servo outputs Up to 12 servos with two adapters For servo decoder YD8248
On order, shipped within 3-8 days