Electronics
DC Clear 3 V/15 mA
In stock, shipped within 1-3 days
Cable plugs. Adapters for connecting three single cables with flat connector system (10603).
In stock, shipped within 1-3 days
Model Can be retrofitted to all C track points with an electric point motor. Digital formats mfx, Motorola, and DCC. Connection by means of plug contacts. The address can be set both with the coding switch (MM 1–320, DCC 1–511) and via CV (MM 1–320, DCC 1–2044) using the programming track. A point lantern can also be controlled; soldering skills are required for this connection. A digital decoder can be fitted to the electric point motor at the same time or later. The decoder is simply connected with plug contacts and can be addressed individually for each point (address 1 to 256). No tools or special knowledge are required for the installation. The digital power supply can be taken directly from the traction current contact on the point. In this way you get a ready-made digital point that is immediately operational even on portable layouts. Highlights Can be retrofitted to all Märklin C track points with an electric point motor Supports the mfx, Motorola, and DCC digital formats Simple installation by means of plug contacts, no special tools needed Address individually adjustable (MM 1–320 / DCC 1–2044), point lantern can be controlled
In stock, shipped within 1-3 days
DC Plug-in bulb with locating lugs Transparent M 60.015 19 V/50 mA
In stock, shipped within 1-3 days
cable harness with 6-pin plug according to NEM 651, DCC colour, length 300mm Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
In stock, shipped within 1-3 days
DC Clear Black wire 16 V/30 mA
In stock, shipped within 1-3 days
DC Long 16 V/30 mA
In stock, shipped within 1-3 days
16 V/30 mA Clear M 3.0 x 0.35 mm
In stock, shipped within 1-3 days
For converting Märklin/Trix H0 locomotives with a built-in high-efficiency motor or other DC motors. The märklin LokDecoder mLD3 has a 21-pin 21mtc interface (to NEM 660) and a matching interface board for retrofitting analogue and digital locomotives. The märklin LokDecoder mLD3 supports the mfx, MM1, MM2 and DCC digital formats.
In stock, shipped within 1-3 days
DC Clear 16 V/35 mA
In stock, shipped within 1-3 days
To activate the switch contacts 6435 and 9425 or the switching track 9115. To fix onto the underside of vehicles. Surface area 7 x 7 mm, height 5 mm.
In stock, shipped within 1-3 days
20 contacts, can be separated at any point For use as pin and tubular socket Spacing 2.54 mm For all systems
In stock, shipped within 1-3 days
Relay 1 A miniature relay, 16 volts With our small relay, loads are controllable whose draw exceeds the decoder’s function output. Put the relay between output and load.
In stock, shipped within 1-3 days
4-pole cable for the connection between the 72752 point control panels or the 72751 signal control panels from the Start up range. Length: 1.80 m.
In stock, shipped within 1-3 days
16 V/30 mA Clear M 3.5 x 0.35 mm
In stock, shipped within 1-3 days
DC transparent Ø 0,3 mm 3 V/15 mA Teflon insulation
In stock, shipped within 1-3 days
DC Clear 16 V/30 mA
In stock, shipped within 1-3 days
Single pole connecting wire and clips for train control operation of semaphore signals.
In stock, shipped within 1-3 days
16 V/30 mA Matt M 3.5 x 0.35 mm
In stock, shipped within 1-3 days
cable harness with 8-pin plug according to NEM 652, DCC colour, length 300mm Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
In stock, shipped within 1-3 days
for low-voltage distribution. 10 pairs of sockets for 2.5 mm plugs.
In stock, shipped within 1-3 days
Model Universal circuit board with several white LEDs, suitable for most of the coaches in the Märklin H0 programme. One 73401 is required for a short coach (e.g. Langenschwalbacher), two for long coaches (e.g. UIC-x with 28.2 cm). The circuit boards can be plugged together several times over or shortened. Mounting material is included. For the electrical connection, the separate power feed 73404, 73405 or 73406 or the current-conducting coupler 72020 with the common return spring 72050 is required, depending on the type of coach. Highlights Bright light in the coach: white LEDs Note The 73400 (dimmed light for earlier eras) and 73401 (white light for more modern coaches) interior lighting kits are technically interchangeable with one another.
In stock, shipped within 1-3 days
This special point machine is a powerful, silent drive with its respective digital decoder for installation in Märklin and Trix C road bed points. The decoder is located in the cable making the drive particularly compact. The point machine stands out for the prototypical slow movement of the point blades. Speed and motion are controlled electronically and ensure a sensitive drive. If – due to the characteristics of your turnout – the direction of the turnout does not fit with the switching direction of the command station, it is possible to set the point motor to reverse mode. The associated decoder is suitable for DC/AC, MM and DCC and is able to send the requested position or the actual position by RailCom to corresponding digital command stations. Analogue mode is possible. Additional switching outputs for relays or LEDs and for a conventional feedback and frog polarisation complete the functions of the point machine. Their function is configurable. Märklin C turnouts: 24611 left hand turnout 24612 right hand turnout 24624 double slip switch DKW 24630 three way turnout (2.pieces drives) 20671 left curved turnout with manual hand lever 20672 right curved turnout with manual hand lever 24671 left curved turnout 24672 right curved turnout 24711 left hand wide radius turnout 24712 right hand wide radius turnout 24771 curved turnout left 24772 curved turnout right Trix C turnouts: 62611 C track left hand turnout 62612 C track right hand turnout 62624 C track double slip switch 62671 C track left curved turnout 62672 C track right curved turnout 62711 left hand wide radius turnout 62712 right hand wide radius turnout 62771 curved turnout left 62772 curved turnout right
In stock, shipped within 1-3 days
Pack of 10
In stock, shipped within 1-3 days