Accessories
25 m reel Single-core PVC insolation 1-colour Loads 3 A Cu.-conducter 18 x 0.10 mm Application: for analog layouts
In stock: 2 on the shelf, shipped within 1-3 days
25 m reel Red/blue Double-core For Märklin® PVC isolation Loads 5 A Cu.-conducter 14 x 0.15 mm Connection to track
In stock: 2 on the shelf, shipped within 1-3 days
DC Candle Transparent 19 V/65 mA
In stock: 2 on the shelf, shipped within 1-3 days
DC Clear 6 mm 1.5 V/100 mA
In stock: 2 on the shelf, shipped within 1-3 days
190 mm long 1 piece
In stock: 2 on the shelf, shipped within 1-3 days
Two wall lamps with yellow/orange LEDs. Simple mounting on house walls. Can also be used to complement the lattice mast lamps 4131 or 8731.
In stock: 2 on the shelf, shipped within 1-3 days
Garden grill with glowing embers. Realistic stone look. With grill grate and storage surface. For connection to 14 – 16 V DC or AC voltage.
In stock: 2 on the shelf, shipped within 1-3 days
A reel of 10 m. Special cable with a diameter of only 0.25 mm (YV wire, 0.05 mm²) with super-thin plastic insulation.
In stock: 2 on the shelf, shipped within 1-3 days
A 10 m reel. Special cable with a diameter of only 0.25 mm (YV wire, 0.05 mm²) with super-thin plastic insulation.
In stock: 2 on the shelf, shipped within 1-3 days
A 10 m reel. Special cable with a diameter of only 0.25 mm (YV wire, 0.05 mm²) with super-thin plastic insulation.
In stock: 2 on the shelf, shipped within 1-3 days
A 10 m reel. Special cable with a diameter of only 0.25 mm (YV wire, 0.05 mm²) with super-thin plastic insulation.
In stock: 2 on the shelf, shipped within 1-3 days
When a train interrupts the infrared light barrier, the timer is triggered. An connected electronic device (up to a maximum of 150 mA) is switched on. After the adjustable time has elapsed (approx. 2–24 seconds), it is automatically switched off. If a train remains stationary within the light barrier, the switch-on time is extended until the light barrier is cleared. Ideally suited for switching on warning flashers, colour light signals, lighting, etc.
In stock: 2 on the shelf, shipped within 1-3 days
Antennas in various types and designs. Air traffic control via 3 red LEDs in the masthead, which flash slowly in turn thanks to the included electronic circuit. Height: 370 mm.
In stock: 2 on the shelf, shipped within 1-3 days
The ground and ballast adhesive was developed by modelling professionals specifically for bonding sand, ballast, grass flock, scatter material, etc. This adhesive is particularly thin and has very low surface tension. Different application techniques are possible:
In stock: 2 on the shelf, shipped within 1-3 days
Glues wood, paper, card, plastics, polystyrene, metals and so on. For all gluing tasks in terrain construction, for applying scatter material, for track ballasting and much more. Can be coloured arbitrarily with the 7595 terrain construction colour powder set. White glue of high industrial quality. Dries quickly and transparently. With practical dosing tip.
In stock: 2 on the shelf, shipped within 1-3 days
Premium Foam Train Service Tray, 328x 166 x 68 mm. With magnetic storage recess The ESU Premium Foam Train Service Tray is the ideal tool for the maintenance and care of your locomotives. Two recesses are available for perfect work: The locomotive can be clamped upside down to comfortably reach the underbody of the locomotive. In the classic inclined tray, you can easily reach the sidewalls of the locomotive or set up the locomotive almost vertically, in order to achieve the interior of the locomotive well. The Premium Foam Train Service Tray consists of a soft, fine-pored foam with high restoring force. As a result, small parts such as handle bars, antennas or pantographs cannot get caught and thus reduce the possibility of damage to a minimum. The material is resistant to oil, grease and other cleaning agents. For safe storage of small parts and screws, a magnetic storage recess is available over the entire length. The Premium Foam Train Service Tray is 328mm long and can be arranged in rows, so that longer Service Trays for the maintenance of railcars can be built. Art.No. Delivery 41010 Premium Foam Train Service Tray, 328x 166 x 68 mm. With magnetic storage recess
In stock: 2 on the shelf, shipped within 1-3 days
Speaker 9mm x 16mm x 3.0mm, square, 6 Ohm, with soundbox, 0.5W This rectangular speaker is slim enough with a width of 9mm to find its installation space even in small H0 or N-track models. Despite its small dimensions, volume and sound are surprisingly balanced. The speaker comes with a matching sound capsule and is a real alternative wherever a larger speaker cannot be accommodated. Art.No. Delivery 50342 Speaker 9mm x 16mm x 3.0mm, square, 6 Ohm, with soundbox, 0.5W
In stock: 2 on the shelf, shipped within 1-3 days
LED lighting strip with taillight, 380mm, 32 LEDs, „white/yellow“, PowerPack. For gauge 1,G The 380mm long, 15mm wide coach interior lighting strip with the part number 50703 is intended for installation in 1 gauge models. It is equipped with both white and yellow LEDs that can be separately dimmed. Thus,for the very first time, you are able to adjust the light colour yourself! Thanks to the digital interface (21MTC) you may add a LokPilot Fx V4.0 function decoder at any time. Part No. 50703 LED lighting strip with taillight, 380mm, 32 LEDs, „white/yellow“, PowerPack. For gauge 1,G
In stock: 2 on the shelf, shipped within 1-3 days
LED lighting strip, taillight, 2 LED, „Red“ Small modules that can easily be installed either in cabs or as end-of-train lights make fitting protypical lighting of your vehicles a simple task. They provide one warmwhite LED or two red LEDs including the needed electronics. Part No. 50704 LED lighting strip, cabin, 1 LED, „warm-white“, 15,0mm x 6,9mm x 2,3 mm 50705 LED lighting strip, taillight, 2 LED, „Red“
In stock: 2 on the shelf, shipped within 1-3 days
Interiour lighting set with decoder, Entry+Red marker light, 264mm, divisible, PowerPack Option, 13 LED, warm white With the digital LED interior lights from ESU, you can retrofit your N, TT or H0 gauge passenger cars with prototypical, uniform lighting. Two versions are available to suit the desired location. The digital interior lights are 264mm long, 9mm slim and each fitted with 13 (!) LEDs. In addition to a version with warm white LEDs (50718), there is also a board with yellow LEDs (50719) so that the light color always matches your existing wagons. Features The digital interior lighting consists of a 74 mm long base section, on which a digital decoder and four LEDs are mounted, and eight adjoining sections, each equipped with one LED spaced 24mm apart. The additional sections can be cut off to customize the length to suit the wagon. Furthermore, two additional 4.5mm wide, detachable LED sections are provided on the far left and right sides to illuminate the entry area. The brightness of the LEDs can be set either using a potentiometer or via software CV and remains constant regardless of the track voltage thanks to the built-in constant voltage supply. A built-in buffer capacitor bridges small current interruptions ex works. To completely prevent flickering even with poor power pickup, a special, very compact PowerPack supercapacitor (ESU item no. 50710) can be connected directly upon request. This can power the LEDs for a few seconds. The digital interior lighting comes with a soldered red tail light. Operating modes The decoder, based on the LokPilot 5 Basic and adapted to the intended use, supports the DCC and Märklin® Motorola® protocols. It can handle 2- and 4-digit addresses and can trigger functions up to F31. Thanks to RailComPlus®, the decoders register fully automatically with a suitable DCC command station. It supports all DCC programming modes, and thanks to RailCom®, the CV values can be read on the main track with suitable command stations. Auxiliary registers are available for command stations that can only program CVs 1-255. Alternatively, the decoder can be read on the programming track without an additional load resistor. The digital interior lighting can also be used on analog AC and DC systems. In both operating modes, the direction of travel is correctly detected and the tail light is switched accordingly. Functions The 13 built-in LEDs can be individually controlled in a total of seven groups: The two entrance LEDs can each be switched separately. The tail light can also be switched separately depending on the direction of travel. Furthermore, there is an amplified output and two outputs for connecting additional LEDs (e.g., for headlights on Pilot cars or toilet lighting), which can be wired individually. Various prototypical lighting effects such as soft dimming, neon tube effects, defective neon tubes, battery lighting, and much more ensure a realistic result. The ESU V5 Function Mapping allows the individual assignment of all LED groups to the desired function keys. Robust You can rely on the experience and quality of a renowned brand manufacturer, even when it comes to digital interior lighting.
In stock: 2 on the shelf, shipped within 1-3 days
Super thin cable, 0.5mm diameter, AWG36, 10m bundle, purple colour Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
In stock: 2 on the shelf, shipped within 1-3 days
Super thin cable, 0.5mm diameter, AWG36, 10m bundle, orange colour Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
In stock: 2 on the shelf, shipped within 1-3 days
Super thin cable, 0.5mm diameter, AWG36, 10m bundle, green colour Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
In stock: 2 on the shelf, shipped within 1-3 days
Super thin cable, 0.5mm diameter, AWG36, 10m bundle, yellow colour Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
In stock: 2 on the shelf, shipped within 1-3 days