Electronic Accessories
Mounting diameter: 0,7 cm, up to 1 A.
In stock: 1 on the shelf, shipped within 1-3 days
Mounting diameter: 0,7 cm, up to 1 A.
In stock: 1 on the shelf, shipped within 1-3 days
Useable as on/off- and switch shifter. Technical data: 2 x UM, load up to max. 2 A.
In stock: 1 on the shelf, shipped within 1-3 days
To be mounted on vehicles base. Even suitable for locomotives with low base clearance. Enable moving trains to switch points or signals, or release feedback by operating in digital systems. Super adhesive pads are attached. Dimensions: L 1 x W 0,5 x H 0,15 cm.
In stock: 1 on the shelf, shipped within 1-3 days
10 sheets with total 1590 self-adhesive labels. These are printed with the most important designations. Inclusive detailed manual. Even learners are enabled to start well-arranged wiring.
In stock: 1 on the shelf, shipped within 1-3 days
Our classic s88N feedback module with current sensing inputs It presents: - 16 current-sensing detectors, arranged in two independent blocks of 8, each with their own Common - 2 Amp continuous current per detector, 8 Amps in total combined over the 16 detectors on the whole module - 5 Amp short duration overload (100ms) capable per detector. - 1-1.5mA current sensitivity - Capacitive input filter on every input, to suppress noise on long cables and track-sections - Configurable on- and off-delay setting for each input for optimal de-bouncing in case of non optimal wheel-track contact - ES-OUT-Link for direct connection to an ES-Link-master - ES-IN-Link connection to other ES-Link enabled modules for module-configuration - Standard s88N connections over RJ45 connectors and ethernet patch cables - Firmware updatable and settings configurable over ES-Link - Power supply directly from ES-Link or s88 bus
In stock: 1 on the shelf, shipped within 1-3 days
The YaMoRC solution for practically all polarity reversing tasks. It presents the following features: - 2-sensor short-circuit free operation. - alternative short-circuit detection mode - follow polarity with external (LocoNet) occupation feedback - follow polarity with turnout at entry - via LocoNet - via DCC - set turnout at exit - 100% solid-state, no relays - RailCom Block-, Address and Rail-Direction Report - LocoNet occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity - ES-Link occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity - ES-Link configuration - Firmware updatable - Current Ratings: - 2A - Continuous Operation - 2.5-2.75A Short Circuit Detection treshold. For reversing as well as short circuit shurdown. - 3.5A - Maximum Current during maximum 5 Seconds ( Command Station/Booster should switch off in this time )
In stock: 1 on the shelf, shipped within 1-3 days
DC Clear 16 V/30 mA
On order, shipped within 10-15 days
DC Yellow 16 V/30 mA
On order, shipped within 10-15 days
DC Red 16 V/30 mA
On order, lead time to be confirmed
DC Green 16 V/30 mA
On order, shipped within 10-15 days
DC Clear ∅ 0.6 mm 3 V/15 mA teflon insulation
On order, shipped within 10-15 days
DC 16 V/30 mA Clear M 60.200
On order, shipped within 10-15 days
DC Spherical-head bulb Transparent Conical 19 V/60 mA
On order, shipped within 10-15 days
DC Clear For Z spotlights 10 V/50 mA
On order, shipped within 10-15 days
DC Clear For Z lights 10 V/30 mA
On order, shipped within 10-15 days
DC Clear For Z lights Short 10 V/30mA
On order, shipped within 10-15 days
DC Clear 3 V/15 mA
On order, shipped within 10-15 days
DC Connect only through 1000 Ohm line resistor Yellow Ø 2 mm
On order, shipped within 10-15 days
DC Connect only through 1000 Ohm line resistor Red Ø 2 mm
On order, lead time to be confirmed
DC Clear 6 mm 1.5 V/100 mA
On order, shipped within 10-15 days
DC Clear 6 mm 6 V/100 mA
On order, shipped within 10-15 days
DC Red 6 mm 19 V/60 mA
On order, lead time to be confirmed
DC Yellow 6 mm 19 V/60 mA
On order, shipped within 10-15 days