Electronic Accessories
The LocoNet analogue switching module is a variant of our LocoNet switching module. An analogue switching module can be configured for: 10 points and 2 handle-operated semaphore signals (momentary contact), 10 colour light signals (maintained contact), 20 switching outputs. Up to 20 analogue switching modules can be operated on one Track-Control.
On order, lead time to be confirmed
4 adjustable holding positions and rotational speed; 4 holding positions per servo switchable via 2 addresses. Switching outputs for lighting, colour and semaphore signals, points, St Andrew's crosses or common crossing polarisation with additional relay. Each output can be configured as a continuous or momentary output.
On order, lead time to be confirmed
It is now possible to connect LocoNet to your computer network or to control the model railway layout directly using your mobile phone or tablet via Wi-Fi.
On order, lead time to be confirmed
The DAISY II Central Station is a compact LocoNet DCC central station for the model railway enthusiast. It is now available in a new, improved version with higher output power and compatibility with the ABC braking system.
On order, lead time to be confirmed
The DAISY II radio hand controller is suitable for operation with all central units featuring a LocoNet connection. It can be plugged directly into the LocoNet to operate via a wired connection, or wirelessly with a radio master which is connected to the central unit via LocoNet. The range of the DAISY II radio hand controller is up to 100 m (open field) to the nearest radio master.
On order, lead time to be confirmed
Free address setting without decoder restrictions Points and signals with a solenoid drive that are to be controlled digitally must be fitted with a solenoid accessory decoder. Lamps, colour light signals or track sections that are to be switched on and off digitally are digitised with a switching decoder. Uhlenbrock solenoid accessory and switching decoders can be used in Märklin, Motorola and DCC digital systems. In Motorola operation, addresses 1–320 can be addressed with the Intellibox, and addresses 1–256 with other command stations. In DCC operation, addresses 1–2048 are possible. The addresses are not preset. They can be chosen freely and independently of one another. Each module has two outputs. Depending on the type, both outputs can be addressed together under one address or independently of each other under two addresses. The relay contacts of the switching decoders have potential-free outputs and can be connected as desired. Each output can be loaded with 1 A. By limiting the connections to two per module, the cable runs remain short and the wiring of the layout stays easy to follow. Connection is conveniently made via screw terminals. Setting the address is extremely simple. First the programming button of the decoder is pressed, then the corresponding point button on the control panel. The decoder simply remembers the corresponding address. The decoders are supplied with operating voltage and control information from the digital command station. Switches by pulse (+20 V) via two addresses, independently of each other, two solenoid accessories with one drive (point, signal) or one solenoid accessory with two drives (three-way point, double slip, signal with distant signal). The module is short-circuit protected. Art. no. 67200 MD2 solenoid accessory decoder
On order, lead time to be confirmed
You can now use LISSY on your digital layout to do everything that was previously only possible with a computer. Without a computer, LISSY makes simple automatic control functions possible, such as block operation and shuttle lines, as well as optimised automatic control of even extensive fiddle yards. LISSY is identical in construction to the Fleischmann Train Navigation and offers interesting additional functions. With LISSY, data are transmitted from the locomotive to the digital system by infrared light. For this, an infrared transmitter is mounted on the vehicle. The infrared sensors of the receiver module are built into the track. LISSY recognises the train and shows which train has entered track 1 of the station. LISSY controls shuttle train operation in the terminus of the single-track branch line. LISSY manages your fiddle yard with through track, independently finds an individual track for each train and, when needed, automatically lets the trains run out of the fiddle yard again. The through track can be used on a locomotive-specific basis or, at the push of a button, by all locomotives. LISSY is a block system for digital layouts and automatically controls the block posts on the layout, without using a computer. LISSY slowly brakes every digital locomotive in front of a red signal using the decoder's internal braking delay. LISSY switches the sound of locomotives depending on the situation, for example the whistle before the tunnel or the horn at the level crossing before the whistle board. LISSY fades out the sound of locomotives fitted with "IntelliSound" when they travel into hidden areas (fiddle yard, tunnel). LISSY switches the lights of a selected locomotive on or off after a certain time, e.g. when the driver has stabled the locomotive. LISSY controls the speed of locomotives, e.g. at station approaches or on slow-speed sections. LISSY measures the speed of passing locomotives to scale. LISSY works without any break in the track and can therefore easily be retrofitted to any model railway layout. Information is displayed on the Intellibox or Track-Control display or on a connected PC. Art. no. 68000 LISSY set: 2 transmitters, 1 receiver, LocoNet cable, manual
On order, lead time to be confirmed
You can now use LISSY on your digital layout to do everything that was previously only possible with a computer. Without a computer, LISSY makes simple automatic control functions possible, such as block operation and shuttle lines, as well as optimised automatic control of even extensive fiddle yards. LISSY is identical in construction to the Fleischmann Train Navigation and offers interesting additional functions. With LISSY, data are transmitted from the locomotive to the digital system by infrared light. For this, an infrared transmitter is mounted on the vehicle. The infrared sensors of the receiver module are built into the track. LISSY recognises the train and shows which train has entered track 1 of the station. LISSY controls shuttle train operation in the terminus of the single-track branch line. LISSY manages your fiddle yard with through track, independently finds an individual track for each train and, when needed, automatically lets the trains run out of the fiddle yard again. The through track can be used on a locomotive-specific basis or, at the push of a button, by all locomotives. LISSY is a block system for digital layouts and automatically controls the block posts on the layout, without using a computer. LISSY slowly brakes every digital locomotive in front of a red signal using the decoder's internal braking delay. LISSY switches the sound of locomotives depending on the situation, for example the whistle before the tunnel or the horn at the level crossing before the whistle board. LISSY fades out the sound of locomotives fitted with "IntelliSound" when they travel into hidden areas (fiddle yard, tunnel). LISSY switches the lights of a selected locomotive on or off after a certain time, e.g. when the driver has stabled the locomotive. LISSY controls the speed of locomotives, e.g. at station approaches or on slow-speed sections. LISSY measures the speed of passing locomotives to scale. LISSY works without any break in the track and can therefore easily be retrofitted to any model railway layout. Information is displayed on the Intellibox or Track-Control display or on a connected PC. With the shuttle train control, the LISSY receivers are pre-configured for a single-track shuttle line, so that the line can be put into operation directly after installation, without any programming effort. The shuttle train control receivers can, like all other receivers, be reprogrammed for other functions. For single-track shuttle lines Pre-configured LISSY receivers for all terminal stops Incl. LISSY transmitter Can be used with Intellibox, Twin-Center and Piko Power-Box Art. no. 68010 LISSY shuttle train control: 1 LISSY transmitter, 2 LISSY receivers, 2 LocoNet cables 2.15 m, the LISSY manual and special instructions for installing and commissioning the shuttle line.
On order, lead time to be confirmed
You can now use LISSY on your digital layout to do everything that was previously only possible with a computer. Without a computer, LISSY makes simple automatic control functions possible, such as block operation and shuttle lines, as well as optimised automatic control of even extensive fiddle yards. LISSY is identical in construction to the Fleischmann Train Navigation and offers interesting additional functions. With LISSY, data are transmitted from the locomotive to the digital system by infrared light. For this, an infrared transmitter is mounted on the vehicle. The infrared sensors of the receiver module are built into the track. LISSY recognises the train and shows which train has entered track 1 of the station. LISSY controls shuttle train operation in the terminus of the single-track branch line. LISSY manages your fiddle yard with through track, independently finds an individual track for each train and, when needed, automatically lets the trains run out of the fiddle yard again. The through track can be used on a locomotive-specific basis or, at the push of a button, by all locomotives. LISSY is a block system for digital layouts and automatically controls the block posts on the layout, without using a computer. LISSY slowly brakes every digital locomotive in front of a red signal using the decoder's internal braking delay. LISSY switches the sound of locomotives depending on the situation, for example the whistle before the tunnel or the horn at the level crossing before the whistle board. LISSY fades out the sound of locomotives fitted with "IntelliSound" when they travel into hidden areas (fiddle yard, tunnel). LISSY switches the lights of a selected locomotive on or off after a certain time, e.g. when the driver has stabled the locomotive. LISSY controls the speed of locomotives, e.g. at station approaches or on slow-speed sections. LISSY measures the speed of passing locomotives to scale. LISSY works without any break in the track and can therefore easily be retrofitted to any model railway layout. Information is displayed on the Intellibox or Track-Control display or on a connected PC. With this station control, the LISSY receivers are pre-configured for a 3-track station with through track, so that the station can be put into operation directly after the receivers are installed, without any programming effort. Two receivers take over the tasks of entry and exit manager, three receivers monitor the various tracks. The receivers can be reprogrammed only for use as station control, e.g. as a station extension for five additional tracks. For stations with digitised points Pre-configured LISSY receivers for a 3-track station with through track or as a station extension for 5 additional tracks Incl. LISSY transmitters for 5 vehicles Can be used with Intellibox, Twin-Center and Piko Power-Box Art. no. 68020 LISSY station control: 5 LISSY receivers, 5 LISSY transmitters, 2 LocoNet cables 2.15 m, 3 LocoNet cables 28 cm, 1 LocoNet 5-way distributor, 1 LocoNet branch (1 plug/2 sockets) 2.15 m, the LISSY manual and special instructions for installing and commissioning the station control.
On order, lead time to be confirmed
You can now use MARCo on your digital layout to do everything that was previously only possible with a computer. Without a computer, MARCo makes simple automatic control functions possible, such as block operation and shuttle lines, as well as optimised automatic control of even extensive fiddle yards. MARCo consists of a RailCom transmitter or a RailCom-capable decoder in the locomotives, and a MARCo receiver connected to a track section. The RailCom data are transmitted via the track. The track section must be operated with a RailCom-capable booster such as Power 4. RailCom works only in the DCC data format. MARCo recognises the train and shows which train has entered track 1 of the station. MARCo controls shuttle train operation in the terminus of the single-track branch line. MARCo manages your fiddle yard with through track, independently finds an individual track for each train and, when needed, automatically lets the trains run out of the fiddle yard again. The through track can be used on a locomotive-specific basis or, at the push of a button, by all locomotives. MARCo is a block system for digital layouts and automatically controls the block posts on the layout, without using a computer. MARCo slowly brakes every digital locomotive in front of a red signal using the decoder's internal braking delay. MARCo switches the sound of locomotives depending on the situation, for example the whistle before the tunnel or the horn at the level crossing before the whistle board. MARCo fades out the sound of locomotives fitted with "IntelliSound" when they travel into hidden areas (fiddle yard, tunnel). MARCo switches the lights of a selected locomotive on or off after a certain time, e.g. when the driver has stabled the locomotive. MARCo controls the speed of locomotives, e.g. at station approaches or on slow-speed sections.
On order, lead time to be confirmed
Art. no. 68341 2 in 1... Lissy and RailCom® transmitter Lissy transmitter for all vehicles that are to be used with the Lissy control system. Installed under the vehicle. Railcom transmitter for retrofitting all vehicles that have a DCC decoder that is not yet RailCom®-capable. Installed in the vehicle. The transmitter is installed in addition to the locomotive decoder in/under a locomotive, or individually in coaches (e.g. driving trailers), and is simply connected to the current collection of the locomotive or coach. You can program it, like a DCC decoder, with all short or long DCC addresses. At a size of just 13 x 7 x 1.8 mm, it is significantly smaller than the previous transmitters and finds room under or in almost all vehicles. Art. no. 68341 LISSY/RailCom® transmitter, pack of 5
On order, lead time to be confirmed
The LISSY micro transmitter module is suitable for connection to IntelliDrive 2 or Piko V4.1 decoders. It is designed for locomotives equipped with Uhlenbrock locomotive or sound decoders featuring a LISSY output. It continuously transmits the decoder address and train category. This transmitter module can only be connected to IntelliDrive 2 decoders.
On order, lead time to be confirmed
The LISSY receiver is a module with two small, barely visible IR sensors with a diameter of 3 mm for installation in the track. The connection to the digital central station is via LocoNet.
On order, lead time to be confirmed
For simple switching functions, the LISSY single receiver is available. The sensor is integrated into the module. For assembly, a 4 mm hole is drilled into the base plate between the sleepers, and the receiver is plugged in from below. Connection to the digital central station is made via a LocoNet cable.
On order, lead time to be confirmed
Complementary product for the 68610 LISSY receiver
On order, lead time to be confirmed
The digital universal controller can be used for many automatic control sequences on a layout and is connected to the digital central station via LocoNet. The controller can monitor 4 track sections and, per track section, signal-dependently slow down and stop a train. Each track section is connected to the controller via 2 terminals. One terminal for the running section and one for the braking section.
On order, lead time to be confirmed
Track-Control – the start The starter set contains all the items that are part of the basic equipment and are usually required only once per control panel: a Track-Control connection module 69060 (Note: the depicted Track-Control connection module has been replaced by item 69060), a LocoNet cable, a CD with the planning software and the manual.
On order, lead time to be confirmed
Track-Control – the start The base set contains all items that are part of the basic equipment and are usually required only once per control panel: a Track-Control connection module 69060 (note: the depicted Track-Control connection module has been replaced by item 69060), a LocoNet cable, a CD with the planning software and the manual.
On order, lead time to be confirmed
The layout grows – Track-Control too The extension set contains 30 segments with scatter discs and click connectors, 32 key caps, four point boards, four signal boards, two crossing connection boards, four connection boards without cut-outs and four different films. Track-Control can be expanded as required. With a large control panel, the power from one connection module may no longer be sufficient. In that case, simply add another 69050 connection module.
On order, lead time to be confirmed
We now offer a complete 9-button control panel with which you can switch 9 different control functions directly. The set includes the connection module, three 3-button modules and 15 segments with plug-in connectors.
On order, lead time to be confirmed
Track-Control – the start The basic set of the "Track-Control Analog" is the inexpensive entry into control panel technology for analogue model railways. It contains all the items that form part of the basic equipment and are only required once per control panel: a connection module, a LocoNet cable and the manual. It also includes a LocoNet analogue switching module, 30 segments with diffusers and connectors, 32 key caps, three turnout boards, three signal boards, four cross-connection boards, two connection boards without illumination and a set of foils for building a small control panel. Extensions You can use all extensions from our Track-Control range, except for the train number display and the speed controller. For occupancy detection (red illumination), Märklin AC modellers use the feedback module 63330. DC modellers need a combination of the feedback module 63330 and the track occupancy detector 43400 for this. The LocoNet switching modules 63410 can also be used. The advanced functions, such as routes, occupancy detections ... are set with the LocoNet Tool and TC-Edit programs. For this you need the USB-LocoNet interface 63120.
On order, lead time to be confirmed
The affordable module makes TrackControl attractive even for small layouts with only a few control panel elements, which draw their required power directly from the LocoNet. For the power supply of large control panels, you can combine several connection modules with the LocoNet distributors 62260 (page 26) and plug-in switched-mode power supplies 62270.
On order, lead time to be confirmed
Item no. 69091 Track-Control film with point symbols
On order, lead time to be confirmed
Item no. 69091 Track-Control film with point symbols
On order, lead time to be confirmed