Wiring & Connectors
8-pole flat ribbon cable. Conductor cross section 0.2 mm². Length 10 m
On order, shipped within 10-15 days
Highly flexible 6-pole spiral cable. Connection between Z21 multiMAUS (10835, 10810) and 10820, 10822, 10815, 10764. Suitable for the FLEISCHMANN multiMAUS from the digital Starter Sets.
On order, shipped within 10-15 days
4-pin data bus distributor module. To connect further input units (for example Lokmaus or Z21 multiMAUS). This distributor module can also be used as an extension of existing lines to units on the slave output. Note: The cable of the Master Lokmaus should not be extended in order to avoid impairing the quality of the data transmission.
On order, shipped within 10-15 days
H0e track connecting cable without radio suppression.
On order, shipped within 10-15 days
Connection terminal. Connection terminal for connection to straight track G121 or curved track R130. Note: There is an anti-interference capacitor in the junction box. It must be removed when using a digital control unit!
On order, shipped within 10-15 days
Feed-in power element for digital DCC operation. It can be connected to any straight or curved track element at the point designated from the factory.
On order, shipped within 10-15 days
in red, blue, black and yellow (10 m each)
On order, lead time to be confirmed
Model Current feed for the 73410 and 73411 retrofit interior lighting kits, consisting of one axle bearing with a soldered-on wire and socket and one axle bearing with a soldered-on wire and plug for the electrical connection. Can be used for the standard design four-axle express train passenger cars from 1928 to 1930 with symmetrical truck mountings. Note With this current feed, for example the Märklin express train passenger cars 42500 to 42540 can be equipped with LED interior lighting using the appropriate DC wheel sets.
On order, shipped within 10-15 days
With inside drill for cable feed-through.
On order, lead time to be confirmed
High-grade litz wire for low-loss current feed and signal transmission.
On order, lead time to be confirmed
High-grade litz wire for low-loss current feed and signal transmission.
On order, lead time to be confirmed
High-grade litz wire for low-loss current feed and signal transmission.
On order, lead time to be confirmed
High-grade litz wire for low-loss current feed and signal transmission.
On order, lead time to be confirmed
High-grade litz wire for low-loss current feed and signal transmission.
On order, lead time to be confirmed
Especially for a safe connection and current transmission.
On order, lead time to be confirmed
Especially for a safe connection and current transmission.
On order, lead time to be confirmed
Especially for a safe connection and current transmission.
On order, lead time to be confirmed
Outer diameter: 0,6 mm.
On order, lead time to be confirmed
The YD6901ES-LINK is the connector that establishes the ES-Link connection between two modules mounted directly next to each other. It is plugged into the ES-Link connections of the two modules, for example between a feedback module YD6016LN and a YD6016ES or a point decoder. This connection is used to expand feedback modules, configure modules with ES-PGM Link, and supply them with firmware updates. For greater distances between the modules, the adapter YD6902ES-EXT with an RJ45 cable is provided. A connector of this type is also included with the configuration stick YD9100. Connector for ES-Link between two modules Contents: 5 pieces
On order, shipped within 3-8 days
The YD6902ES-EXT is an adapter set used to establish the ES-Link connection between two modules via a standard CAT5 patch cable. It is used when the modules are not mounted directly next to each other and the YD6901ES-LINK connector is insufficient. The set consists of one adapter for the ES-OUT-Link connection and one adapter for the ES-IN-Link connection, each with an RJ45 socket. This allows, for example, the configuration stick YD9100 to be connected to a more distant module. ES-Link via CAT5 patch cable Includes an adapter for ES-IN Link and ES-OUT Link RJ45 sockets
On order, shipped within 3-8 days