LokPilot decoders
LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl. The decoder accepts all DCC programming modes and thanks to RailCom® the CV values can be read on the main track with RailCom equipped DCC systems. For command stations that only program the CVs from 1-255 auxiliary CV registers exist. The LokPilot 5 DCC decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACKCommands or the Lenz® ABC system. Also braking with DCC brake modules or with DC voltageis possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle trainenables automatic commuting between two train stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The top speedcan be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5DCC packed with function outputs. Depending on the interface version, each LokPilot offers 5 DCCDecoder at least 10 amplified function outputs with 250mA output current each. In the executionswith PluX22 or 21MTC interface there are 4 outputs to control servos orLogic level outputs added. All-important lighting functions are available. The brightness of each outputcan be set separately. The decoder masters automatic pushing and pullingwhen uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 DCC has been fundamentally improved again. A variably adjustablePWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors.Operation - The typical “hum” is a thing of the past. The load control now has up to10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enablesthe automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to 1.5A of motor current. Enough juice even for older motors. Operational safety On request, a PowerPack can be fitted to the LokPilot 5 DCC to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Analog Gleichspannung (abschaltbar). Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59620 LokPilot 5 DCC, 8-pin NEM652, gauge H0 ,0 59622 LokPilot 5 DCC, PLUX22 NEM658, gauge H0 ,0 59626 LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 59629 LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 59659 LokPilot 5 DCC, 21MTC MKL, gauge H0 ,0
In stock: 4 on the shelf, shipped within 1-3 days
LokPilot 5 micro DCC, Next18, gauge N, TT The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a pure DCC Decoder. This lack of flexibility is rewarded with a lower price. LokPilot 5 micro DCC decoders are available with all common interfaces. The variants with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but have 2 additional function outputs. Modes The LokPilot 5 micro DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 micro DCC decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5 micro DCC equipped with an amazing number of function outputs. The variants with 6-pin or 8-pin Wiring harnesses offer 4 amplified function outputs, each with 180mA output current and two logic level outputs. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs available. All important lighting effects are available. The brightness of each output can be adjusted separately. The decoder masters automatic pushing and pulling when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The motor control of the LokPilot 5 micro DCC has been fundamentally improved again. A variable adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors- The typical “hum” is a thing of the past. The load control now has up to 10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enables the automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors. Safety A PowerPack to bypass dirty track can be fitted to the LokPilot 5 micro. Protection Of course, the motor output and the function outputs are against overload protected. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59820 LokPilot 5 micro DCC, 8-pin NEM652, gauge N, TT 59824 LokPilot 5 micro DCC, PluX16, gauge N, TT 59826 LokPilot 5 micro DCC, 6-pin NEM651, gauge N, TT 59827 LokPilot 5 micro DCC, 6-pin Direkt, gauge N, TT 59828 LokPilot 5 micro DCC, Next18, gauge N, TT 59857 LokPilot 5 micro DCC, 6-pin Direkt gewinkelt, gauge N, TT
In stock: 4 on the shelf, shipped within 1-3 days
LokPilot 5 DCC/MM/SX/M4, PLUX22 NEM658, gauge H0 ,0 The LokPilot 5 is the most important representative of the LokPilot family and is suitable for almost all questions in locomotives of gauge H0 and 0. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The M4 protocol enables automatic registration at mfx®-compatible control centers. All 32 possible function keys are offered here. The LokPilot 5 decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC and AC railways.The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. Therefore, we packed the LokPilot 5 with function outputs. Depending on the interface version, each LokPilot 5 decoder offers at least 10 amplified function outputs with 250mA output current each. In the versions with PluX22 or 21MTC interface, 4 outputs are added to control servos or logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 1.5A motor current, the LokPilot 5 decoder provides enough juice even for older motors. Operational safety On request, a PowerPack can be connected to the LokPilot 5 to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Possible under Selectrix® operation. Programming must be carried out in DCC mode. Programming with "pure" Selectrix® devices is not possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Digital Motorola® (alt und neu), bis zu 255 Adressen im Motorola®-Betrieb Selectrix® Fahrbetrieb M4-Betrieb (Automatische Anmeldung an mfx®-kompatiblen Zentralen) Analog Gleichspannung (abschaltbar). Analog Wechselspannung (abschaltbar) Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Intelligenter Programmiermodus mit Märklin® 6021® Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59610 LokPilot 5 DCC/MM/SX/M4, 8-pin NEM652, gauge H0 ,0 59612 LokPilot 5 DCC/MM/SX/M4, PLUX22 NEM658, gauge H0 ,0 59616 LokPilot 5 DCC/MM/SX/M4, 6-pin NEM651, gauge H0 ,0 59619 LokPilot 5 DCC/MM/SX/M4, 21MTC NEM660, gauge H0 ,0 59649 LokPilot 5 DCC/MM/SX/M4, 21MTC MKL, gauge H0 ,0
In stock: 3 on the shelf, shipped within 1-3 days
LokPilot 5 DCC/MM/SX/M4, 21MTC NEM660, gauge H0 ,0 The LokPilot 5 is the most important representative of the LokPilot family and is suitable for almost all questions in locomotives of gauge H0 and 0. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The M4 protocol enables automatic registration at mfx®-compatible control centers. All 32 possible function keys are offered here. The LokPilot 5 decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC and AC railways.The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. Therefore, we packed the LokPilot 5 with function outputs. Depending on the interface version, each LokPilot 5 decoder offers at least 10 amplified function outputs with 250mA output current each. In the versions with PluX22 or 21MTC interface, 4 outputs are added to control servos or logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 1.5A motor current, the LokPilot 5 decoder provides enough juice even for older motors. Operational safety On request, a PowerPack can be connected to the LokPilot 5 to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Possible under Selectrix® operation. Programming must be carried out in DCC mode. Programming with "pure" Selectrix® devices is not possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Digital Motorola® (alt und neu), bis zu 255 Adressen im Motorola®-Betrieb Selectrix® Fahrbetrieb M4-Betrieb (Automatische Anmeldung an mfx®-kompatiblen Zentralen) Analog Gleichspannung (abschaltbar). Analog Wechselspannung (abschaltbar) Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Intelligenter Programmiermodus mit Märklin® 6021® Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59610 LokPilot 5 DCC/MM/SX/M4, 8-pin NEM652, gauge H0 ,0 59612 LokPilot 5 DCC/MM/SX/M4, PLUX22 NEM658, gauge H0 ,0 59616 LokPilot 5 DCC/MM/SX/M4, 6-pin NEM651, gauge H0 ,0 59619 LokPilot 5 DCC/MM/SX/M4, 21MTC NEM660, gauge H0 ,0 59649 LokPilot 5 DCC/MM/SX/M4, 21MTC MKL, gauge H0 ,0
In stock: 3 on the shelf, shipped within 1-3 days
LokPilot 5 DCC, PLUX22 NEM658, gauge H0 ,0 The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl. The decoder accepts all DCC programming modes and thanks to RailCom® the CV values can be read on the main track with RailCom equipped DCC systems. For command stations that only program the CVs from 1-255 auxiliary CV registers exist. The LokPilot 5 DCC decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACKCommands or the Lenz® ABC system. Also braking with DCC brake modules or with DC voltageis possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle trainenables automatic commuting between two train stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The top speedcan be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5DCC packed with function outputs. Depending on the interface version, each LokPilot offers 5 DCCDecoder at least 10 amplified function outputs with 250mA output current each. In the executionswith PluX22 or 21MTC interface there are 4 outputs to control servos orLogic level outputs added. All-important lighting functions are available. The brightness of each outputcan be set separately. The decoder masters automatic pushing and pullingwhen uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 DCC has been fundamentally improved again. A variably adjustablePWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors.Operation - The typical “hum” is a thing of the past. The load control now has up to10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enablesthe automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to 1.5A of motor current. Enough juice even for older motors. Operational safety On request, a PowerPack can be fitted to the LokPilot 5 DCC to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Analog Gleichspannung (abschaltbar). Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59620 LokPilot 5 DCC, 8-pin NEM652, gauge H0 ,0 59622 LokPilot 5 DCC, PLUX22 NEM658, gauge H0 ,0 59626 LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 59629 LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 59659 LokPilot 5 DCC, 21MTC MKL, gauge H0 ,0
In stock: 3 on the shelf, shipped within 1-3 days
LokPilot 5 micro DCC Direct Kato USA »Blank decoder«, gauge: N The LokPilot 5 micro DCC Direct Kato USA has been specially developed for installation in N scale locomotives of the Kato USA brand. This decoder can be easily installed in most American diesel locomotives of this manufacturer instead of the analog board installed as standard. The LokPilot 5 micro DCC Direct Kato USA with its dimensions of 60.0mm x 10.1mm is a pure DCC decoder. Modes The LokPilot 5 micro DCC Direct Kato USA is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully to a suitable digital center. It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokPilot 5 micro DCC Direct Kato USA Decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or DC voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An AUTOMATIC ABC commuter train allows automatic commuting between two stations. The LokPilot 5 micro DCC Direct Kato USA can be used on analog DC. The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions Despite its compact dimensions, the LokPilot 5 micro DCC Direct Kato USA is equipped with an enormous number of function outputs. Two directly soldered SMD LEDs are designed for front and rear head lighting. For older models, two 3mm LEDs can be soldered and controlled separately (one at each end resistor protected). Three further powered function outputs (non-resistor protected) are also available. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 micro DCC Direct Kato USA has a variable PWM clock frequency from 10kHz to 50kHz, which ensures super-quiet operation, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokPilot 5 micro DCC Direct Kato USA decoder delivers up to 0.9A motor power. Operational reliability A PowerPack can be connected to the LokPilot 5 micro DCC Direct Kato USA on request to bridge dirty rail sections using the logic level output AUX6. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 59741 LokPilot 5 micro DCC Direct Kato USA »Blank decoder«, gauge: N
In stock: 3 on the shelf, shipped within 1-3 days
LokPilot 5 micro DCC/MM/SX, 6-pin Direkt, gauge N, TT The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm) that it can be used even in very small locomotives Nominal sizes Z, N or TT can accommodate. Nevertheless, functionality and robustness were not spared compared to the larger versions. LokPilot 5 micro decoders are offered with all common interfaces. The versions with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but they also speak for the mfx®-compatible M4 protocol. Modes The LokPilot 5 micro is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The Next18 and PluX16 variants also allow automatic registration to mfx®-compatible control centers thanks to the M4 protocol. All 32 possible function keys are offered here. The LokPilot 5 micro decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC trains. The versions with Next18 or PluX16 can also be used on analog AC systems. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. That is why we have equipped the LokPilot 5 micro with an astonishing number of function outputs. The variants with 6-pin or 8-pin wiring harness offer 4 amplified function outputs with 180mA output current each as well as two logic level outputs for servos or Susi. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. motor control The engine control of the LokPilot 5 micro has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 0.75A motor current, the LokPilot 5 micro decoder provides enough juice for the intended application scenarios. Operational safety On request, a PowerPack can be connected to the LokPilot 5 micro to bridge dirty rail sections. Protection Of course, the motor output and the function outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59810 LokPilot 5 micro DCC/MM/SX, 8-pin NEM652, gauge N, TT 59814 LokPilot 5 micro DCC/MM/SX/M4, PluX16, gauge N, TT 59816 LokPilot 5 micro DCC/MM/SX, 6-pin NEM651, gauge N, TT 59817 LokPilot 5 micro DCC/MM/SX, 6-pin Direkt, gauge N, TT 59818 LokPilot 5 micro DCC/MM/SX/M4, Next18, gauge N, TT 59837 LokPilot 5 micro DCC/MM/SX, 6-pin Direct angled, gauge N, TT
In stock: 3 on the shelf, shipped within 1-3 days
LokPilot 5 FX micro DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge N, TT The LokPilot 5 Fx micro and its “twin” LokPilot 5 Fx micro DCC is an extremely small function only decoders with NO MOTOR CONTROL and a footprint of only 8.0mm x 7.0mm. The thickness is only 2.4mm (on the capacitor: 2.9 mm). It is used in all vehicles of nominal sizes N to HO scale that do not need a motor output, but should still be able to activate lighting effects. LokPilot 5 Fx micro decoders are always offered with an 8-pin interface. Operating Modes The LokPilot 5 Fx micro is a true multi-protocol decoder. It supports the DCC data format as well as Motorola® and Selectrix®. In the DCC format, 14 to 128 speed steps are a given, as are short (1-127) and long (128-9999) addresses and up to 32 functions. Thanks to RailComPlus®, the decoders register fully automatically with a suitable digital command stations such as the ESU ECoS or CabControl. It supports all DCC programming modes, and thanks to RailCom®, the CV values can be read on the main track with suitable command stations. Auxiliary CVs are available for command stations that can only program CVs 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses allow the triggering of 16 functions. A built-in programming mode also allows programming with the venerable 6021 Control Unit. The LokPilot 5 Fx DCC “only” speaks the DCC protocol, but can also be automatically registered with corresponding command stations using RailComPlus®. The LokPilot 5 Fx micro decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train control system enables automatic shuttling between two stations. This is also important with a function decoder to synchronize control cars (Cab Control) and motor driven rail vehicles. The LokPilot 5 Fx decoder can be used on analog DC railways. The decoder switches between the operating modes fully automatically "on-the-fly". In most cases, no adjustments are required. Functions The LokPilot 5 Fx micro or LokPilot 5 Fx micro DCC has been equipped with an astonishing number of function outputs. There are 6 powered function outputs with 180mA output current each and two logic level outputs for servos or Susi. The brightness of each output can be adjusted separately. Operational safety If required, a PowerPack can be connected to the LokPilot 5 Fx micro and LokPilot 5 Fx micro DCC to bridge dirty track sections. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 59110 LokPilot 5 FX micro DCC/MM/SX, 8-pin NEM652, »NO MOTOR CONTROL« gauge N, TT 59120 LokPilot 5 FX micro DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge N, TT
In stock: 2 on the shelf, shipped within 1-3 days
LokPilot 5 Fx DCC/MM/SX, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 The LokPilot 5 Fx is a function decoder without motor output and therefore perfect for installation in control cars or function models. Because it talks DCC with RailCom® as well as Motorola® and Selectrix, it can be used with all common digital centers. He shares his flexible radio-onskey assignment and the manifold lighting effects with the other LokPilot 5 decoders from ESU. The LokPilot 5 Fx is supplied in three variants: In addition to the "classic" version with 8-pin NEM 652 harness, a variant for the 21MTC interface and with PluX22 interface is also available. Modes The LokPilot 5 Fx is a multi-protocol decoder. It masters the DCC data format as well as Motorola® and Selectrix®. In DCC format, 14-128 driving steps are as natural as 2- and 4-digit addresses. Up to 28 functions can be triggered. Thanks to RailComPlus® the de-coders register fully automatically at a suitable digital center (e.g. ECoS). It masters all DCC programming modes and can be used and programmed with all DCC-compatible digital centers: RailCom® also allows the CV values to be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255 (e.g. ROCO® multi-mouse). Motorola® users benefit from up to 28 driving steps at 255 addresses. Three additional Motorola® addresses enable the triggering of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The LokPilot 5 Fx Decoder erkennd ie Märklin®-Bremsstrecke n ee eensnso wie ZIMO®-HLU/ZACK-Brems- commands or the Lenz® ABC system. Braking with DCC brake blocks or with equal voltage is also possible. In addition, it also "stops" with a Selectrix® brake diode.An AUTOMATIC ABC commuter train allows automatic commuting between two stations. Although this decoder does not have an engine output, this is also important with a function decoder in order to be able to synchronize control cars and motor cars. The LokPilot 5 FX decoder can be used on analog DC and AC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Fx has been equipped with an astonishing number of function outputs. Depending on the cutting version, each LokPilot 5 Fx decoder offers at least 10 reinforced function outputs with 250mA output current each. In the versions with PluX22 or 21MTC interface, 4 outputs for controlling servos or logic level outputs are added. All important lighting functions are available. The brightness of each output can be set separately. Interaction The LokPilot 5 Fx is designed for an interaction with the LokSound 5 and the LokPilot 5 decoders: for example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 decoder and the control car with a LokPilot 5 Fx. Provided the same address, both behave absolutely identically. The identical arrangement of the CVs facilitates the tuning of the two decoders. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Fx to bridge dirty rail cuts. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Digital Motorola® (alt und neu), bis zu 255 Adressen im Motorola®-Betrieb Selectrix® Fahrbetrieb Analog Gleichspannung (abschaltbar). Analog Wechselspannung (abschaltbar) Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Intelligenter Programmiermodus mit Märklin® 6021® Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: Nicht vorhanden Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 1500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 16,5mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59210 LokPilot 5 Fx DCC/MM/SX, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 59212 LokPilot 5 Fx DCC/MM/SX, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 59219 LokPilot 5 Fx DCC/MM/SX, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0
In stock: 2 on the shelf, shipped within 1-3 days
LokPilot 5 Fx DCC/MM/SX, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 The LokPilot 5 Fx is a function decoder without motor output and therefore perfect for installation in control cars or function models. Because it talks DCC with RailCom® as well as Motorola® and Selectrix, it can be used with all common digital centers. He shares his flexible radio-onskey assignment and the manifold lighting effects with the other LokPilot 5 decoders from ESU. The LokPilot 5 Fx is supplied in three variants: In addition to the "classic" version with 8-pin NEM 652 harness, a variant for the 21MTC interface and with PluX22 interface is also available. Modes The LokPilot 5 Fx is a multi-protocol decoder. It masters the DCC data format as well as Motorola® and Selectrix®. In DCC format, 14-128 driving steps are as natural as 2- and 4-digit addresses. Up to 28 functions can be triggered. Thanks to RailComPlus® the de-coders register fully automatically at a suitable digital center (e.g. ECoS). It masters all DCC programming modes and can be used and programmed with all DCC-compatible digital centers: RailCom® also allows the CV values to be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255 (e.g. ROCO® multi-mouse). Motorola® users benefit from up to 28 driving steps at 255 addresses. Three additional Motorola® addresses enable the triggering of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The LokPilot 5 Fx Decoder erkennd ie Märklin®-Bremsstrecke n ee eensnso wie ZIMO®-HLU/ZACK-Brems- commands or the Lenz® ABC system. Braking with DCC brake blocks or with equal voltage is also possible. In addition, it also "stops" with a Selectrix® brake diode.An AUTOMATIC ABC commuter train allows automatic commuting between two stations. Although this decoder does not have an engine output, this is also important with a function decoder in order to be able to synchronize control cars and motor cars. The LokPilot 5 FX decoder can be used on analog DC and AC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Fx has been equipped with an astonishing number of function outputs. Depending on the cutting version, each LokPilot 5 Fx decoder offers at least 10 reinforced function outputs with 250mA output current each. In the versions with PluX22 or 21MTC interface, 4 outputs for controlling servos or logic level outputs are added. All important lighting functions are available. The brightness of each output can be set separately. Interaction The LokPilot 5 Fx is designed for an interaction with the LokSound 5 and the LokPilot 5 decoders: for example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 decoder and the control car with a LokPilot 5 Fx. Provided the same address, both behave absolutely identically. The identical arrangement of the CVs facilitates the tuning of the two decoders. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Fx to bridge dirty rail cuts. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Digital Motorola® (alt und neu), bis zu 255 Adressen im Motorola®-Betrieb Selectrix® Fahrbetrieb Analog Gleichspannung (abschaltbar). Analog Wechselspannung (abschaltbar) Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Intelligenter Programmiermodus mit Märklin® 6021® Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: Nicht vorhanden Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 1500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 16,5mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59210 LokPilot 5 Fx DCC/MM/SX, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 59212 LokPilot 5 Fx DCC/MM/SX, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 59219 LokPilot 5 Fx DCC/MM/SX, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0
In stock: 2 on the shelf, shipped within 1-3 days
LokPilot 5 micro DCC/MM/SX/M4, PluX16, gauge N, TT The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm) that it can be used even in very small locomotives Nominal sizes Z, N or TT can accommodate. Nevertheless, functionality and robustness were not spared compared to the larger versions. LokPilot 5 micro decoders are offered with all common interfaces. The versions with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but they also speak for the mfx®-compatible M4 protocol. Modes The LokPilot 5 micro is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The Next18 and PluX16 variants also allow automatic registration to mfx®-compatible control centers thanks to the M4 protocol. All 32 possible function keys are offered here. The LokPilot 5 micro decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC trains. The versions with Next18 or PluX16 can also be used on analog AC systems. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. That is why we have equipped the LokPilot 5 micro with an astonishing number of function outputs. The variants with 6-pin or 8-pin wiring harness offer 4 amplified function outputs with 180mA output current each as well as two logic level outputs for servos or Susi. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. motor control The engine control of the LokPilot 5 micro has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 0.75A motor current, the LokPilot 5 micro decoder provides enough juice for the intended application scenarios. Operational safety On request, a PowerPack can be connected to the LokPilot 5 micro to bridge dirty rail sections. Protection Of course, the motor output and the function outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59810 LokPilot 5 micro DCC/MM/SX, 8-pin NEM652, gauge N, TT 59814 LokPilot 5 micro DCC/MM/SX/M4, PluX16, gauge N, TT 59816 LokPilot 5 micro DCC/MM/SX, 6-pin NEM651, gauge N, TT 59817 LokPilot 5 micro DCC/MM/SX, 6-pin Direkt, gauge N, TT 59818 LokPilot 5 micro DCC/MM/SX/M4, Next18, gauge N, TT 59837 LokPilot 5 micro DCC/MM/SX, 6-pin Direct angled, gauge N, TT
In stock: 2 on the shelf, shipped within 1-3 days
LokPilot 5 micro DCC, PluX16, gauge N, TT The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a pure DCC Decoder. This lack of flexibility is rewarded with a lower price. LokPilot 5 micro DCC decoders are available with all common interfaces. The variants with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but have 2 additional function outputs. Modes The LokPilot 5 micro DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 micro DCC decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5 micro DCC equipped with an amazing number of function outputs. The variants with 6-pin or 8-pin Wiring harnesses offer 4 amplified function outputs, each with 180mA output current and two logic level outputs. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs available. All important lighting effects are available. The brightness of each output can be adjusted separately. The decoder masters automatic pushing and pulling when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The motor control of the LokPilot 5 micro DCC has been fundamentally improved again. A variable adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors- The typical “hum” is a thing of the past. The load control now has up to 10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enables the automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors. Safety A PowerPack to bypass dirty track can be fitted to the LokPilot 5 micro. Protection Of course, the motor output and the function outputs are against overload protected. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59820 LokPilot 5 micro DCC, 8-pin NEM652, gauge N, TT 59824 LokPilot 5 micro DCC, PluX16, gauge N, TT 59826 LokPilot 5 micro DCC, 6-pin NEM651, gauge N, TT 59827 LokPilot 5 micro DCC, 6-pin Direkt, gauge N, TT 59828 LokPilot 5 micro DCC, Next18, gauge N, TT 59857 LokPilot 5 micro DCC, 6-pin Direkt gewinkelt, gauge N, TT
In stock: 2 on the shelf, shipped within 1-3 days
LokPilot 5 micro DCC/MM/SX, 6-pin Direct angled, gauge N, TT The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm) that it can be used even in very small locomotives Nominal sizes Z, N or TT can accommodate. Nevertheless, functionality and robustness were not spared compared to the larger versions. LokPilot 5 micro decoders are offered with all common interfaces. The versions with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but they also speak for the mfx®-compatible M4 protocol. Modes The LokPilot 5 micro is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The Next18 and PluX16 variants also allow automatic registration to mfx®-compatible control centers thanks to the M4 protocol. All 32 possible function keys are offered here. The LokPilot 5 micro decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC trains. The versions with Next18 or PluX16 can also be used on analog AC systems. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. That is why we have equipped the LokPilot 5 micro with an astonishing number of function outputs. The variants with 6-pin or 8-pin wiring harness offer 4 amplified function outputs with 180mA output current each as well as two logic level outputs for servos or Susi. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. motor control The engine control of the LokPilot 5 micro has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 0.75A motor current, the LokPilot 5 micro decoder provides enough juice for the intended application scenarios. Operational safety On request, a PowerPack can be connected to the LokPilot 5 micro to bridge dirty rail sections. Protection Of course, the motor output and the function outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59810 LokPilot 5 micro DCC/MM/SX, 8-pin NEM652, gauge N, TT 59814 LokPilot 5 micro DCC/MM/SX/M4, PluX16, gauge N, TT 59816 LokPilot 5 micro DCC/MM/SX, 6-pin NEM651, gauge N, TT 59817 LokPilot 5 micro DCC/MM/SX, 6-pin Direkt, gauge N, TT 59818 LokPilot 5 micro DCC/MM/SX/M4, Next18, gauge N, TT 59837 LokPilot 5 micro DCC/MM/SX, 6-pin Direct angled, gauge N, TT
In stock: 2 on the shelf, shipped within 1-3 days
LokPilot 5 Basic, 8-pin NEM652, Gauge H0, 0 While LokPilot 5 decoders can undoubtedly meet all imaginable requirements of even the most demanding experts, many model railway eras are looking for a robust, high-quality DCC decoder for your standard requirements, which should also be affordable. The LokPilot 5 Basic was developed with the aim of offering a modern decoder with a reasonable range of functions at a reasonable price. The LokPilot 5 Basic comes in two versions: In addition to a version with an 8-pin NEM interface, a version with 21MTC interface is also available. This makes the LokPilot 5 Basic particularly suitable for use in track H0 vehicles. Modes The LokPilot 5 Basic is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 20 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully automatically to a suitable digital center. It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokPilot 5 Basic Decoder detects the Märklin® brake distances as well as the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible.The LokPilot 5 Basic Decoder can be used on analog DC webs. The maximum speed can be set separately.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Basic has 4 reinforced function outputs in each version. In the 21MTC interface, there are 8 logic-level outputs at the interface, two of which are also suitable for controlling servos. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 Basic delivers up to 0.9A continuous current. A variable PWM clock frequency from 10kHz to 50kHz ensures super-quiet operation, especially for bell anchor motors – The typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Basic to bridge dirty rail cuts. Protection Of course, all function outputs as well as the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59020 LokPilot 5 Basic, 8-pin NEM652, Gauge H0, 0 59029 LokPilot 5 Basic, 21MTC NEM660, Gauge H0, 0
In stock: 1 on the shelf, shipped within 1-3 days
LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 The LokPilot 5 Fx DCC is a function decoder with NO MOTOR CONTROL and is therefore perfect for installation in control cars (Cab Cars) or rail vehicles that only need lights and/or lighting effects. As the "twin brother" of the LokPilot 5 Fx, it shares its features and the basic characteristics of all other LokPilot 5 decoders, but is a pure DCC decoder. The LokPilot 5 Fx DCC is supplied in three versions: In addition to the "classic" version with 8-pin NEM 652 wiring harness, a version for the 21MTC interface and a PluX22 interface is also available. Operating Modes The LokPilot 5 Fx DCC is a pure DCC decoder. 14 to 128 speed steps are as standard as short (1-127) and long (128-9999) addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable command stations such as those from ESU. Auxiliary CVs exist for command stations that can only program the CVs from 1-255. The LokPilot 5 Fx DCC decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An automatic ABC shuttle train system enables automatic shuttle operation between two stations. Although this decoder does not have motor control, it is important for the decoder to be able to synchronize non-motorized rail vehicles with those that are motorized. The LokPilot 5 Fx DCC decoder can be used on analog DC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustments are required. Functions The LokPilot 5 Fx DCC has been equipped with an astonishing number of function outputs. Depending on the interface version, each LokPilot 5 Fx DCC decoder offers at least 10 powered function outputs, each with a max output current of 250mA for lights. Versions with a PluX22 or 21MTC interface also feature 4 outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. Interaction The LokPilot 5 Fx DCC is designed to work with the LokSound 5 and the LokPilot 5 decoders: For example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 decoder and the control car (Cab Car) with a LokPilot 5 Fx DCC. Provided they have the same address, both behave identically. The identical CV arrangement makes it easier to coordinate the two decoders. Operational reliability A PowerPack can be connected to the LokPilot 5 Fx DCC to bridge dirty track sections. Protection The outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Technical Specifications Operating Modes: NMRA/DCC with 14, 28, and 128 speed steps, DCC RailCom® DCC 2-digit and 4-digit addresses (short and long addresses) Analog DC voltage (can be switched off). Automatic detection of operating mode and DCC speed step setting Support for Lenz® LG100, Märklin®, Roco® braking sections, and ZIMO® HLU commands Support for ABC braking mode and ABC shuttle train section Wrong-way bit / saving operating states Shunting mode and acceleration and braking delay can be switched via button Speed controller: NO MOTOR CONTROL Function outputs: 10 powered function outputs Version with 21MTC interface has 2 additional logic level outputs and 2 further logic level outputs instead of SUSI Version with PluX22 interface has 2 logic level outputs instead of SUSI 250mA load capacity per powered output Total current of all function outputs approx. 1500mA. Short-circuit-proof outputs Functional output assignments freely selectable (function mapping) Dimensions: 16.5 mm x 15.5 mm x 4.5 mm Instruction manual Art.No. Delivery 59220 LokPilot 5 Fx DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 59222 LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 59229 LokPilot 5 Fx DCC, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0
In stock: 1 on the shelf, shipped within 1-3 days
LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl. The decoder accepts all DCC programming modes and thanks to RailCom® the CV values can be read on the main track with RailCom equipped DCC systems. For command stations that only program the CVs from 1-255 auxiliary CV registers exist. The LokPilot 5 DCC decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACKCommands or the Lenz® ABC system. Also braking with DCC brake modules or with DC voltageis possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle trainenables automatic commuting between two train stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The top speedcan be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5DCC packed with function outputs. Depending on the interface version, each LokPilot offers 5 DCCDecoder at least 10 amplified function outputs with 250mA output current each. In the executionswith PluX22 or 21MTC interface there are 4 outputs to control servos orLogic level outputs added. All-important lighting functions are available. The brightness of each outputcan be set separately. The decoder masters automatic pushing and pullingwhen uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 DCC has been fundamentally improved again. A variably adjustablePWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors.Operation - The typical “hum” is a thing of the past. The load control now has up to10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enablesthe automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to 1.5A of motor current. Enough juice even for older motors. Operational safety On request, a PowerPack can be fitted to the LokPilot 5 DCC to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Analog Gleichspannung (abschaltbar). Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59620 LokPilot 5 DCC, 8-pin NEM652, gauge H0 ,0 59622 LokPilot 5 DCC, PLUX22 NEM658, gauge H0 ,0 59626 LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 59629 LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 59659 LokPilot 5 DCC, 21MTC MKL, gauge H0 ,0
In stock: 1 on the shelf, shipped within 1-3 days
LokPilot 5 Basic, 21MTC NEM660, Gauge H0, 0 While LokPilot 5 decoders can undoubtedly meet all imaginable requirements of even the most demanding experts, many model railway eras are looking for a robust, high-quality DCC decoder for your standard requirements, which should also be affordable. The LokPilot 5 Basic was developed with the aim of offering a modern decoder with a reasonable range of functions at a reasonable price. The LokPilot 5 Basic comes in two versions: In addition to a version with an 8-pin NEM interface, a version with 21MTC interface is also available. This makes the LokPilot 5 Basic particularly suitable for use in track H0 vehicles. Modes The LokPilot 5 Basic is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 20 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully automatically to a suitable digital center. It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokPilot 5 Basic Decoder detects the Märklin® brake distances as well as the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible.The LokPilot 5 Basic Decoder can be used on analog DC webs. The maximum speed can be set separately.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Basic has 4 reinforced function outputs in each version. In the 21MTC interface, there are 8 logic-level outputs at the interface, two of which are also suitable for controlling servos. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 Basic delivers up to 0.9A continuous current. A variable PWM clock frequency from 10kHz to 50kHz ensures super-quiet operation, especially for bell anchor motors – The typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Basic to bridge dirty rail cuts. Protection Of course, all function outputs as well as the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59020 LokPilot 5 Basic, 8-pin NEM652, Gauge H0, 0 59029 LokPilot 5 Basic, 21MTC NEM660, Gauge H0, 0
On order, shipped within 4-5 days
LokPilot 5 FX micro DCC/MM/SX, 8-pin NEM652, »NO MOTOR CONTROL« gauge N, TT The LokPilot 5 Fx micro and its “twin” LokPilot 5 Fx micro DCC is an extremely small function only decoders with NO MOTOR CONTROL and a footprint of only 8.0mm x 7.0mm. The thickness is only 2.4mm (on the capacitor: 2.9 mm). It is used in all vehicles of nominal sizes N to HO scale that do not need a motor output, but should still be able to activate lighting effects. LokPilot 5 Fx micro decoders are always offered with an 8-pin interface. Operating Modes The LokPilot 5 Fx micro is a true multi-protocol decoder. It supports the DCC data format as well as Motorola® and Selectrix®. In the DCC format, 14 to 128 speed steps are a given, as are short (1-127) and long (128-9999) addresses and up to 32 functions. Thanks to RailComPlus®, the decoders register fully automatically with a suitable digital command stations such as the ESU ECoS or CabControl. It supports all DCC programming modes, and thanks to RailCom®, the CV values can be read on the main track with suitable command stations. Auxiliary CVs are available for command stations that can only program CVs 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses allow the triggering of 16 functions. A built-in programming mode also allows programming with the venerable 6021 Control Unit. The LokPilot 5 Fx DCC “only” speaks the DCC protocol, but can also be automatically registered with corresponding command stations using RailComPlus®. The LokPilot 5 Fx micro decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train control system enables automatic shuttling between two stations. This is also important with a function decoder to synchronize control cars (Cab Control) and motor driven rail vehicles. The LokPilot 5 Fx decoder can be used on analog DC railways. The decoder switches between the operating modes fully automatically "on-the-fly". In most cases, no adjustments are required. Functions The LokPilot 5 Fx micro or LokPilot 5 Fx micro DCC has been equipped with an astonishing number of function outputs. There are 6 powered function outputs with 180mA output current each and two logic level outputs for servos or Susi. The brightness of each output can be adjusted separately. Operational safety If required, a PowerPack can be connected to the LokPilot 5 Fx micro and LokPilot 5 Fx micro DCC to bridge dirty track sections. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 59110 LokPilot 5 FX micro DCC/MM/SX, 8-pin NEM652, »NO MOTOR CONTROL« gauge N, TT 59120 LokPilot 5 FX micro DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 Fx micro DCC/MM/SX, Next18, »NO MOTOR CONTROL« gauge N, TT The LokPilot 5 Fx micro and its "twin" LokPilot 5 Fx micro DCC are versatile decoders with a Next18 interface on a footprint of 13.0mm x 9.2mm. They are used in all vehicles of nominal sizes N to H0, which do not have an engine output, but should still be able to switch light effects. Modes The LokPilot 5 Fx micro is a multi-protocol decoder. It masters the DCC data format as well as Motorola® and Selectrix®. In DCC format, 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses and up to 32 functions. With the help of RailComPlus® technology, the de-coders register fully automatically at a suitable digital center.It masters all DCC programming modes and can be both driven and programmed with compatible digital centers: Thanks to RailCom®, it is possible to read out the CV values on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255.Motorola® users benefit from up to 28 driving steps at 255 addresses. Three additional Motorola® addresses enable the triggering of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021.The LokPilot 5 Fx micro DCC speaks "only" the DCC protocol, but can also be automatically registered with RailComPlus® at appropriate control centers.The LokPilot 5 Fx micro decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or with equal voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An automatic ABC pen train allows automatic commuting between two stations. Although this decoder does not have an engine output, this is also important for a function decoder in order to be able to synchronize control cars and motor cars.The LokPilot 5 Fx micro decoder can be used on analog DC and ac current webs; the LokPilot 5 Fx micro DCC on analog DC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Fx micro or LokPilot 5 Fx micro DCC has been equipped with an astonishing number of function outputs. Thus, 6 reinforced function outputs with 180mA output current each as well as two logic level outputs for servos or Susi are available. The brightness of each output can be set separately. Interaction LokPilot 5 Fx micro are designed for interaction with the LokSound 5 and the LokPilot 5 decoders: for example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 micro decoder and the control car with a LokPilot 5 Fx micro. Provided the same address, both are absolutely identical. The identical arrangement of the CVs facilitates the tuning of the two decoders. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Fx micro and LokPilot 5 Fx micro DCC to bridge dirty rail cuts. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59118 LokPilot 5 Fx micro DCC/MM/SX, Next18, »NO MOTOR CONTROL« gauge N, TT 59128 LokPilot 5 Fx micro DCC, Next18, »NO MOTOR CONTROL« gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 Fx micro DCC, Next18, »NO MOTOR CONTROL« gauge N, TT The LokPilot 5 Fx micro and its "twin" LokPilot 5 Fx micro DCC are versatile decoders with a Next18 interface on a footprint of 13.0mm x 9.2mm. They are used in all vehicles of nominal sizes N to H0, which do not have an engine output, but should still be able to switch light effects. Modes The LokPilot 5 Fx micro is a multi-protocol decoder. It masters the DCC data format as well as Motorola® and Selectrix®. In DCC format, 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses and up to 32 functions. With the help of RailComPlus® technology, the de-coders register fully automatically at a suitable digital center.It masters all DCC programming modes and can be both driven and programmed with compatible digital centers: Thanks to RailCom®, it is possible to read out the CV values on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255.Motorola® users benefit from up to 28 driving steps at 255 addresses. Three additional Motorola® addresses enable the triggering of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021.The LokPilot 5 Fx micro DCC speaks "only" the DCC protocol, but can also be automatically registered with RailComPlus® at appropriate control centers.The LokPilot 5 Fx micro decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or with equal voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An automatic ABC pen train allows automatic commuting between two stations. Although this decoder does not have an engine output, this is also important for a function decoder in order to be able to synchronize control cars and motor cars.The LokPilot 5 Fx micro decoder can be used on analog DC and ac current webs; the LokPilot 5 Fx micro DCC on analog DC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Fx micro or LokPilot 5 Fx micro DCC has been equipped with an astonishing number of function outputs. Thus, 6 reinforced function outputs with 180mA output current each as well as two logic level outputs for servos or Susi are available. The brightness of each output can be set separately. Interaction LokPilot 5 Fx micro are designed for interaction with the LokSound 5 and the LokPilot 5 decoders: for example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 micro decoder and the control car with a LokPilot 5 Fx micro. Provided the same address, both are absolutely identical. The identical arrangement of the CVs facilitates the tuning of the two decoders. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Fx micro and LokPilot 5 Fx micro DCC to bridge dirty rail cuts. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59118 LokPilot 5 Fx micro DCC/MM/SX, Next18, »NO MOTOR CONTROL« gauge N, TT 59128 LokPilot 5 Fx micro DCC, Next18, »NO MOTOR CONTROL« gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 Fx DCC/MM/SX, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0 The LokPilot 5 Fx is a function decoder without motor output and therefore perfect for installation in control cars or function models. Because it talks DCC with RailCom® as well as Motorola® and Selectrix, it can be used with all common digital centers. He shares his flexible radio-onskey assignment and the manifold lighting effects with the other LokPilot 5 decoders from ESU. The LokPilot 5 Fx is supplied in three variants: In addition to the "classic" version with 8-pin NEM 652 harness, a variant for the 21MTC interface and with PluX22 interface is also available. Modes The LokPilot 5 Fx is a multi-protocol decoder. It masters the DCC data format as well as Motorola® and Selectrix®. In DCC format, 14-128 driving steps are as natural as 2- and 4-digit addresses. Up to 28 functions can be triggered. Thanks to RailComPlus® the de-coders register fully automatically at a suitable digital center (e.g. ECoS). It masters all DCC programming modes and can be used and programmed with all DCC-compatible digital centers: RailCom® also allows the CV values to be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255 (e.g. ROCO® multi-mouse). Motorola® users benefit from up to 28 driving steps at 255 addresses. Three additional Motorola® addresses enable the triggering of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The LokPilot 5 Fx Decoder erkennd ie Märklin®-Bremsstrecke n ee eensnso wie ZIMO®-HLU/ZACK-Brems- commands or the Lenz® ABC system. Braking with DCC brake blocks or with equal voltage is also possible. In addition, it also "stops" with a Selectrix® brake diode.An AUTOMATIC ABC commuter train allows automatic commuting between two stations. Although this decoder does not have an engine output, this is also important with a function decoder in order to be able to synchronize control cars and motor cars. The LokPilot 5 FX decoder can be used on analog DC and AC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Fx has been equipped with an astonishing number of function outputs. Depending on the cutting version, each LokPilot 5 Fx decoder offers at least 10 reinforced function outputs with 250mA output current each. In the versions with PluX22 or 21MTC interface, 4 outputs for controlling servos or logic level outputs are added. All important lighting functions are available. The brightness of each output can be set separately. Interaction The LokPilot 5 Fx is designed for an interaction with the LokSound 5 and the LokPilot 5 decoders: for example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 decoder and the control car with a LokPilot 5 Fx. Provided the same address, both behave absolutely identically. The identical arrangement of the CVs facilitates the tuning of the two decoders. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Fx to bridge dirty rail cuts. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Digital Motorola® (alt und neu), bis zu 255 Adressen im Motorola®-Betrieb Selectrix® Fahrbetrieb Analog Gleichspannung (abschaltbar). Analog Wechselspannung (abschaltbar) Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Intelligenter Programmiermodus mit Märklin® 6021® Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: Nicht vorhanden Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 1500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 16,5mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59210 LokPilot 5 Fx DCC/MM/SX, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 59212 LokPilot 5 Fx DCC/MM/SX, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 59219 LokPilot 5 Fx DCC/MM/SX, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0
On order, shipped within 4-5 days
LokPilot 5 Fx DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 The LokPilot 5 Fx DCC is a function decoder with NO MOTOR CONTROL and is therefore perfect for installation in control cars (Cab Cars) or rail vehicles that only need lights and/or lighting effects. As the "twin brother" of the LokPilot 5 Fx, it shares its features and the basic characteristics of all other LokPilot 5 decoders, but is a pure DCC decoder. The LokPilot 5 Fx DCC is supplied in three versions: In addition to the "classic" version with 8-pin NEM 652 wiring harness, a version for the 21MTC interface and a PluX22 interface is also available. Operating Modes The LokPilot 5 Fx DCC is a pure DCC decoder. 14 to 128 speed steps are as standard as short (1-127) and long (128-9999) addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable command stations such as those from ESU. Auxiliary CVs exist for command stations that can only program the CVs from 1-255. The LokPilot 5 Fx DCC decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An automatic ABC shuttle train system enables automatic shuttle operation between two stations. Although this decoder does not have motor control, it is important for the decoder to be able to synchronize non-motorized rail vehicles with those that are motorized. The LokPilot 5 Fx DCC decoder can be used on analog DC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustments are required. Functions The LokPilot 5 Fx DCC has been equipped with an astonishing number of function outputs. Depending on the interface version, each LokPilot 5 Fx DCC decoder offers at least 10 powered function outputs, each with a max output current of 250mA for lights. Versions with a PluX22 or 21MTC interface also feature 4 outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. Interaction The LokPilot 5 Fx DCC is designed to work with the LokSound 5 and the LokPilot 5 decoders: For example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 decoder and the control car (Cab Car) with a LokPilot 5 Fx DCC. Provided they have the same address, both behave identically. The identical CV arrangement makes it easier to coordinate the two decoders. Operational reliability A PowerPack can be connected to the LokPilot 5 Fx DCC to bridge dirty track sections. Protection The outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Technical Specifications Operating Modes: NMRA/DCC with 14, 28, and 128 speed steps, DCC RailCom® DCC 2-digit and 4-digit addresses (short and long addresses) Analog DC voltage (can be switched off). Automatic detection of operating mode and DCC speed step setting Support for Lenz® LG100, Märklin®, Roco® braking sections, and ZIMO® HLU commands Support for ABC braking mode and ABC shuttle train section Wrong-way bit / saving operating states Shunting mode and acceleration and braking delay can be switched via button Speed controller: NO MOTOR CONTROL Function outputs: 10 powered function outputs Version with 21MTC interface has 2 additional logic level outputs and 2 further logic level outputs instead of SUSI Version with PluX22 interface has 2 logic level outputs instead of SUSI 250mA load capacity per powered output Total current of all function outputs approx. 1500mA. Short-circuit-proof outputs Functional output assignments freely selectable (function mapping) Dimensions: 16.5 mm x 15.5 mm x 4.5 mm Instruction manual Art.No. Delivery 59220 LokPilot 5 Fx DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 59222 LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 59229 LokPilot 5 Fx DCC, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0
On order, shipped within 4-5 days
LokPilot 5 Fx DCC, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0 The LokPilot 5 Fx DCC is a function decoder with NO MOTOR CONTROL and is therefore perfect for installation in control cars (Cab Cars) or rail vehicles that only need lights and/or lighting effects. As the "twin brother" of the LokPilot 5 Fx, it shares its features and the basic characteristics of all other LokPilot 5 decoders, but is a pure DCC decoder. The LokPilot 5 Fx DCC is supplied in three versions: In addition to the "classic" version with 8-pin NEM 652 wiring harness, a version for the 21MTC interface and a PluX22 interface is also available. Operating Modes The LokPilot 5 Fx DCC is a pure DCC decoder. 14 to 128 speed steps are as standard as short (1-127) and long (128-9999) addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable command stations such as those from ESU. Auxiliary CVs exist for command stations that can only program the CVs from 1-255. The LokPilot 5 Fx DCC decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An automatic ABC shuttle train system enables automatic shuttle operation between two stations. Although this decoder does not have motor control, it is important for the decoder to be able to synchronize non-motorized rail vehicles with those that are motorized. The LokPilot 5 Fx DCC decoder can be used on analog DC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustments are required. Functions The LokPilot 5 Fx DCC has been equipped with an astonishing number of function outputs. Depending on the interface version, each LokPilot 5 Fx DCC decoder offers at least 10 powered function outputs, each with a max output current of 250mA for lights. Versions with a PluX22 or 21MTC interface also feature 4 outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. Interaction The LokPilot 5 Fx DCC is designed to work with the LokSound 5 and the LokPilot 5 decoders: For example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 decoder and the control car (Cab Car) with a LokPilot 5 Fx DCC. Provided they have the same address, both behave identically. The identical CV arrangement makes it easier to coordinate the two decoders. Operational reliability A PowerPack can be connected to the LokPilot 5 Fx DCC to bridge dirty track sections. Protection The outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Technical Specifications Operating Modes: NMRA/DCC with 14, 28, and 128 speed steps, DCC RailCom® DCC 2-digit and 4-digit addresses (short and long addresses) Analog DC voltage (can be switched off). Automatic detection of operating mode and DCC speed step setting Support for Lenz® LG100, Märklin®, Roco® braking sections, and ZIMO® HLU commands Support for ABC braking mode and ABC shuttle train section Wrong-way bit / saving operating states Shunting mode and acceleration and braking delay can be switched via button Speed controller: NO MOTOR CONTROL Function outputs: 10 powered function outputs Version with 21MTC interface has 2 additional logic level outputs and 2 further logic level outputs instead of SUSI Version with PluX22 interface has 2 logic level outputs instead of SUSI 250mA load capacity per powered output Total current of all function outputs approx. 1500mA. Short-circuit-proof outputs Functional output assignments freely selectable (function mapping) Dimensions: 16.5 mm x 15.5 mm x 4.5 mm Instruction manual Art.No. Delivery 59220 LokPilot 5 Fx DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 59222 LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 59229 LokPilot 5 Fx DCC, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0
On order, shipped within 4-5 days
LokPilot 5 L DCC/MM/SX/M4, Pinheader with adapter, gauge 0, G, I The LokPilot 5 L finds its place wherever the LokPilot 5 no longer “fits” in terms of performance. Ideally, these are vehicles of nominal size 0, but also gauge 1 vehicles that are to be equipped without noise are conceivable application scenarios. The LokPilot 5 L is mechanically compatible with the LokSound 5 L decoder and has the same connection pins. It is also the same size as the LokSound 5 L with the dimensions of 50.8mm x 24.5mm x 14mm and is equipped with an integrated PowerPack. Modes The LokPilot 5 L is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The M4 protocol enables automatic registration at mfx®-compatible control centers. All 32 possible function keys are offered here. The LokPilot 5 L decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 L decoder can be used on analog DC and AC railways. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features Each LokPilot 5 L comes with 11 amplified function outputs, each with a load of 500mA. In addition, there are 6 further logic level outputs, which can also control (2 pieces) RC servos or SUSI expansion modules on request. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. Two sensor inputs can trigger functions on request. Motor control The engine control of the LokPilot 5 L has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 3.0A motor current, the LokPilot 5 L decoder provides enough juice even for older motors. Operational safety A PowerPack installed directly on the decoder helps to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 59315 LokPilot 5 L DCC/MM/SX/M4, Pinheader with adapter, gauge 0, G, I 59325 LokPilot 5 L DCC, Pinheader with adapter, gauge 0, G, I
On order, shipped within 4-5 days