Feedback modules and accessories
Our classic s88N feedback module with current sensing inputs It presents: - 16 current-sensing detectors, arranged in two independent blocks of 8, each with their own Common - 2 Amp continuous current per detector, 8 Amps in total combined over the 16 detectors on the whole module - 5 Amp short duration overload (100ms) capable per detector. - 1-1.5mA current sensitivity - Capacitive input filter on every input, to suppress noise on long cables and track-sections - Configurable on- and off-delay setting for each input for optimal de-bouncing in case of non optimal wheel-track contact - ES-OUT-Link for direct connection to an ES-Link-master - ES-IN-Link connection to other ES-Link enabled modules for module-configuration - Standard s88N connections over RJ45 connectors and ethernet patch cables - Firmware updatable and settings configurable over ES-Link - Power supply directly from ES-Link or s88 bus
In stock: 1 on the shelf, shipped within 1-3 days
The YaMoRC solution for practically all polarity reversing tasks. It presents the following features: - 2-sensor short-circuit free operation. - alternative short-circuit detection mode - follow polarity with external (LocoNet) occupation feedback - follow polarity with turnout at entry - via LocoNet - via DCC - set turnout at exit - 100% solid-state, no relays - RailCom Block-, Address and Rail-Direction Report - LocoNet occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity - ES-Link occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity - ES-Link configuration - Firmware updatable - Current Ratings: - 2A - Continuous Operation - 2.5-2.75A Short Circuit Detection treshold. For reversing as well as short circuit shurdown. - 3.5A - Maximum Current during maximum 5 Seconds ( Command Station/Booster should switch off in this time )
In stock: 1 on the shelf, shipped within 1-3 days
The YD6016ES-GND is a feedback module for the s88N bus with sixteen logic-based inputs. The state of push buttons, switches, or reed contacts is detected against the common connection C. The inputs are divided into two groups of eight, each input has a capacitive input filter, and the on and off delay is adjustable per input. Connection is via RJ45 sockets and standard Ethernet patch cables, alternatively via ES-Link, which also handles firmware updates and configuration. The module is designed for 5 V on the s88 bus and must not be operated on control units with 12 V on the s88N connection. 16 inputs in two groups of 8 For push buttons, switches, reed contacts Powered via ES-Link or s88 bus Housing 84 x 88 x 22 mm
On order, shipped within 3-8 days
Our standard current-sensing feedback module with LocoNet Interface It presents: - 16 current-sensing detectors, arranged in two independent blocks of 8, each with their own Common - 2 Amp continuous current per detector, 8 Amps in total combined over the 16 detectors on the whole module - 5 Amp short duration overload (100ms) capable per detector. - 1-1.5mA current sensitivity - Capacitive input filter on every input, to suppress noise on long cables and track-sections - Configurable on- and off-delay setting for each input for optimal de-bouncing in case of non optimal wheel-track contact - Every input individually configurable for various actions like feedback, turnout toggle, turnout throw, turnout close - Every input individually configurable for feedback- or turnout-address - ES-IN-Link for direct connection of up to 5 additional YD6016ES modules (effectively creating a 96 input LocoNet module) - ES-IN-Link connection to other ES-Link enabled modules for module-configuration - ES-IN-Link connection to YD9101 for web-based configuration - USB connection with one Virtual COM ports for the YD.Command** protocol - Firmware updatable over USB - Power supply directly from LocoNet-T or -B ( or USB for easy configuration and updating on a PC ) **)Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.
On order, shipped within 3-8 days
Our standard ground-input feedback module with LocoNet Interface with: - 16 inputs, switching against Ground ( both "C" terminals ) - Capacitive input filter on every input, to suppress noise on long cables - Configurable on- and off-delay setting for each input for optimal de-bouncing of pushbuttons, switches, reed contacts - Every input individually configurable for various actions like feedback, turnout toggle, turnout throw, turnout close - Every input individually configurable for feedback- or turnout-address - ES-IN-Link for direct connection of up to 5 additional YD6016ES modules (effectively creating a 96 input LocoNet module) - ES-IN-Link connection to other ES-Link enabled modules for module-configuration - ES-IN-Link connection to YD9101 for web-based configuration - USB connection with one Virtual COM ports for the YD.Command** protocol - Firmware updatable over USB - Power supply directly from LocoNet-T or -B ( or USB for easy configuration and updating on a PC ) **)Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.
On order, shipped within 3-8 days
The YD6016LN-RC is a feedback module for LocoNet with sixteen inputs and sixteen local RailCom detectors. Up to four locomotive addresses are detected per section via RailCom Channel 1 or Channel 2 and reported to the central station. An additional global detector monitors the track output. For vehicles without RailCom, the inputs also function as current sensors. The module supports reading out locomotive and accessory decoders via POM, as well as reporting QoS, speed, and container fill level. Power is supplied via the track input, with the connection to LocoNet T or B. An extension to 96 feedback units is possible via s88N-IN or ES-IN Link. Address range 1 to 4096 Occupancy detection from 3 mA 2 A per input, 4 A total Configuration and firmware update via USB
On order, lead time to be confirmed
Our standard current-sensing feedback module with RBus / XBus Interface It presents: - 16 current-sensing detectors, arranged in two independent blocks of 8, each with their own Common - 2 Amp continuous current per detector, 8 Amps in total combined over the 16 detectors on the whole module - 5 Amp short duration overload (100ms) capable per detector. - 1mA current sensitivity - Capacitive input filter on every input, to suppress noise on long cables and track-sections - Configurable on- and off-delay setting for each input for optimal de-bouncing in case of non optimal wheel-track contact - Every input individually configurable for various actions like feedback, turnout toggle, turnout throw, turnout close - Every input individually configurable for turnout-address - ES-IN-Link for direct connection of up to 4 additional YD6016ES modules (effectively creating a 80 input RBus module) - ES-IN-Link connection to other ES-Link enabled modules for module-configuration - ES-IN-Link connection to YD9101 for web-based configuration - USB connection with one Virtual COM port for the YD.Command** protocol - Firmware updatable over USB - Power supply directly from RBus / XBus ( or USB for easy configuration and updating on a PC ) - Experimental: XpressNet feedback reporting. This enables more then 160 feedbacks on the white z21® command stations. **)Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.
On order, shipped within 3-8 days
The YD6940 is a set of two adapters for point motors that require polarity reversal to switch, so-called motor or stall motors. The adapter is used with the YD8116 switching decoder, for example for drives from Conrad, Hoffmann, Tillig, Fulgurex, Tortoise and Cobalt Analog. It is also required for Kato two-wire solenoid point motors on the YD8008 and YD8044 point decoders. It is also recommended for two-wire motor drives on the YD8248 servo decoder. Each adapter handles currents up to 3 A. Contents: 2 adapters For motor drives with polarity reversal on the YD8116 For Kato magnetic drives on the YD8008 and YD8044 Rated up to 3 A
On order, shipped within 3-8 days
The YD6942 is a set of two adapters that allow common-cathode (negative return) light signals to be operated with the YD8116 switching decoder. The adapter has one side for connection to the decoder and one side for connection of the signal, each with screw terminals. A 270 Ohm resistor is fitted on the adapter. This limits the output current to approximately 50 to 70 mA, depending on the supply voltage. Contents: 2 adapters For signals with a common cathode on the YD8116 Integrated 270 Ohm resistor Current limited to approximately 50 to 70 mA
On order, lead time to be confirmed
Let your Fleischmann, Roco, Märklin or DIY turntable being operated fully digitally Our specialized TurnTable Controller. It presents: - Full, regulated, Motor-Control, with acceleration and dynamic braking. - Supports DCC and Motorola turnout commands - Supports DCCext "aspect" driven commands. - LocoNet, for feedback in- and output and turnout-command input - Control protocols: Fleischmann (TurnControl) & Märklin (7686) - Built-in DCC generator for "Profi" variant ( Decoder in bridge ) - RailCom detector for the bridge - Occupance sensor for the bridge - Automatic, configurable polarity switching per entry - Three-button manual controls - ES-LINK-IN for extra position-sensor modules and the YD7652EX, extender for Märklin and Roco Turntables It currently supports: - Fleischmann H0 6052 (Brass track) - Fleischmann H0 6152 (Profi track) = Roco 6152 - Fleischmann H0 6651 (New-Silver track) - Fleischmann H0 6652 (3-rail & 2-rail) = Roco 665201 - Fleischmann H0 6154 (Profi track, small bridge) = Roco 6154 - Fleischmann N 9152 - Roco H0 42615 - Roco TT 35900 - Märklin H0 7286 Power: - Input 10–19 V DC (16–19 V DC recommended), max. 60 W Recommended Upgrade: - Replacement motor from SB-Modellbau Modes, modules and turntables: Turntable(s) Mode Module(s) Turntable remains unmodified Basic YD7652 6052, 6152, 6651, 6652 (2-rail), 6154, 9152, 35900 These turntables make a clicking sound while turning in Basic mode, due to the way the positions are counted. These turntables can be connected directly to the YD7652, no further modules needed. Turntable remains unmodified Basic YD7652 + YD7652EX Märklin H0 7286 These turntables make a clicking sound while turning in Basic mode, due to the way the positions are counted. These turntables can be connected directly to the YD7652EX. The YD7652EX is connected to the YD7652 with the TURN-Link and ES-Link adapter boards. Turntable remains unmodified Basic YD7652 + YD7652EX 6652/Roco 665201 (3-rail) These turntables make a clicking sound while turning in Basic mode, due to the way the positions are counted. These turntables can be connected to the YD7652EX with the 6652 adapter installed. The YD7652EX is connected to the YD7652 with the TURN-Link and ES-Link adapter boards. Turntable remains unmodified, must be set in "1" mode Basic YD7652 + YD7652EX Roco H0 42615 These turntables make a clicking sound while passing an exit, due to the mechanical sensor on the bridge-end. These turntables can be connected to the YD7652EX with the Roco-Edge adapter installed. The YD7652EX is connected to the YD7652 with the TURN-Link and ES-Link adapter boards. Turntable remains unmodified Basic-Plus YD7652 + YD7652ES 6052, 6152, 6651, 6652 (2-rail), 6154, 9152, 35900 These turntables can be controlled in such a way, that the position of the bridge is sensed. And can thus turn without the need for counting the positions and in that way turn without clicking sound. These turntables can be connected directly to the YD7652. For the position sensing, one or more YD7652ES are needed. Turntable bridge needs installation of a DCC Loco-Decoder Profi-Plus YD7652 + YD7652ES 6052, 6152, 6651, 6652 (2-rail), 6154, 9152, 35900 The Profi mode relies on the fact that the bridge motor is controlled by a loco-decoder, the bridge latch by a function output of that decoder. The YD7652 will then output a DCC signal on it's motor connections. Multiple decoders can be built into the bridge. These turntables can be connected directly to the YD7652. For the position sensing, one or more YD7652ES are needed. Modes, modules and turntables
On order, shipped within 3-8 days
The YD7652ES-OPTO is the position sensor module for the turntable control YD7652. It detects the position of the turntable platform via the track connections, allowing the control system to know the position without counting the track connections. The lock is only disengaged once, and the platform rotates without clicking to the selected track. One module processes up to 12 track connections; if there are more connections, an additional YD7652ES is connected. The connection to the YD7652 is made via ES-Link. No modifications to the turntable are required, as all track connections are connected to the module on both sides. For turntable control YD7652 Up to 12 track connections per module Connection via ES-Link For Fleischmann 6052, 6152, 6154, 6651, 9152 and Roco 35900
On order, shipped within 3-8 days
The YD7652EX-TURN is an extension of the turntable controller YD7652 for connecting turntables from Märklin (H0 7286) and Roco (H0 42615). The turntable type is set using a link plug. The module contains an 8-bit sensor module for the signals from the Roco and Märklin turntables and passes the ES-Link through. The contents supplied include the RocoEdge adapter, the TURN-Link plug, and the ES-Link plug, which are used to connect the module to the YD7652. The module is also required for the Fleischmann/Roco turntable 6652 or 665201 in 3-rail operation; the necessary plug for this is available from the retailer on request. For Märklin H0 7286 and Roco H0 42615 Turntable type via plug-in bridge Including RocoEdge adapter, TURN-Link and ES-Link bridge
On order, shipped within 3-8 days
The YD8290 is a relay expansion adapter for the servo decoder YD8248. It is connected to the switching outputs of the YD8248 and provides four relays. The relays can be used for the polarity of the common crossing of four points, one relay per point, or in pairs for two points, with the common crossing de-energised during the servo movement. The four relays can also be used for other switching tasks or a combination thereof. Depending on the use, adjustments to the configuration of the YD8248 may be required. 4 relays Relay voltage 5 V Contact current max. 2 A For servo decoder YD8248
On order, shipped within 3-8 days
The YD8291 is a servo expansion adapter for the servo decoder YD8248. Up to four additional RC servos can be plugged in and controlled to each YD8291. By using two YD8291 adapters, a total of twelve servos can be operated on one YD8248. The adapter is connected to the switching outputs of the YD8248; depending on the use, adjustments in the decoder configuration may be necessary. 4 additional servo outputs Up to 12 servos with two adapters For servo decoder YD8248
On order, shipped within 3-8 days
The YD9100 is a USB configuration module for all YaMoRC modules with an ES-PGM-Link or ES-OUT-Link connection, for example the YD8008, YD8044 and YD8116 decoders or the YD7403 booster. It provides a virtual COM port on the PC, through which the PC configuration software changes the settings of the connected modules and carries out firmware updates. The stick has a genuine FTDI USB chip and a mini-USB connection. The connection to the module is made using the supplied YD6901 connector; for greater distances, the YD6902ES-EXT adapter and an RJ45 cable are used. The manufacturer recommends a USB isolator. USB with virtual COM port Mini-USB socket Includes YD6901 ES-Link connector
On order, shipped within 3-8 days
The YD7652HS is a position sensor board for use with all variants of Fleischmann turntables. The YD7652HS has been specially developed for turntables that no longer have ‘contact tabs’ on the bridge, which would otherwise make Basic-Plus operation (turning without the ‘click-clack’ sound) impossible. With this board mounted beneath the pit and a magnet beneath the turntable bridge, the bridge’s position is detected with pinpoint accuracy. It is also a cost-effective alternative to the YD7652ES sensor when there are more than 12 access tracks. It presents: - 48 Hall-effect sensors, highly sensitive - Extremely strong neodymium magnet included - ES-Link connected directly to the YD7652 via an RJ45 cable - All fixing materials included - Available for both large and small Fleischmann turntables - Very simple installation and adjustment
The YD7652ST-STEP is an extension of the turntable control YD7652 for connecting turntables with stepper motor drive. It contains a quiet stepper motor driver, whose settings are controlled by the processor, with micro-steps from 8 to 256 as well as dynamic acceleration and deceleration. A connection for a home or index sensor (for example Hall or infrared) is built in. The supply of the turntable track is passed through by the YD7652 with automatic polarisation. Supply 12 to 19 V Motor current max. 1.2 A Microsteps 8 to 256 Connection for home/index sensor