Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Rolling Stock

Locomotives, multiple units, coaches and wagons, new and pre-owned, from Z to G, checked by modellers.
Filter products
H0 Passenger Coach Bnb719 "Quelle" DB
Brawa 46675 Scale H0
H0 Passenger Coach Bnb719 "Quelle" DB

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 103.70

On order, shipped within 10-15 days

H0 Control Car BDnrzf738 "Hengstenberg" DB
Brawa 46676 Scale H0
H0 Control Car BDnrzf738 "Hengstenberg" DB

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 108.20

On order, shipped within 10-15 days

H0 Control Car BDnrzf738 "Hengstenberg" DB
Brawa 46677 Scale H0
H0 Control Car BDnrzf738 "Hengstenberg" DB

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 126.25

On order, shipped within 10-15 days

H0 Control Car BDnrzf738 "Hengstenberg" DB
Brawa 46678 Scale H0
H0 Control Car BDnrzf738 "Hengstenberg" DB

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 171.40

On order, shipped within 10-15 days

H0 Passenger Coach ABnrzb704 "Bahlsen" DB
Brawa 46679 Scale H0
H0 Passenger Coach ABnrzb704 "Bahlsen" DB

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 81.15

On order, shipped within 10-15 days

H0 Passenger Coach ABnrzb704 "Bahlsen" DB
Brawa 46680 Scale H0
H0 Passenger Coach ABnrzb704 "Bahlsen" DB

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 99.20

On order, shipped within 10-15 days

H0 Passenger Coach ABnrzb704 "Bahlsen" DB
Brawa 46681 Scale H0
H0 Passenger Coach ABnrzb704 "Bahlsen" DB

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 103.70

On order, shipped within 10-15 days

H0 Passenger Coach ABn417 "Jägermeister" DB
Brawa 46682 Scale H0
H0 Passenger Coach ABn417 "Jägermeister" DB

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 81.15

On order, shipped within 10-15 days

H0 Passenger Coach ABn417 "Jägermeister" DB
Brawa 46684 Scale H0
H0 Passenger Coach ABn417 "Jägermeister" DB

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 103.70

On order, shipped within 10-15 days

H0 Control Car Bdnf736 DB (Köln Hbf)
Brawa 46685 Scale H0
H0 Control Car Bdnf736 DB (Köln Hbf)

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 108.20

On order, shipped within 10-15 days

H0 Control Car Bdnf736 DB (Köln Hbf)
Brawa 46687 Scale H0
H0 Control Car Bdnf736 DB (Köln Hbf)

Prototype The conversion programmes for 3yg- and 4yg coaches allowed the German Federal Railway to address the shortage of coaches caused by the war for the first time from the mid-1950s. However, the construction programmes were limited initially to developing urban rapid transit and express train coaches. Following this, the German Federal Railway created capacity for developing new commuter coaches (n-coaches). The constantly growing demand for increased traffic volume and the fact that the 3yg had only been designed for a short service life, led to the appearance of the first prototypes for the new n-coaches in 1958. Based on the findings of the preceding new developments and prototypes, three basic types emerged with five 1st class compartments in the centre of the coach and two large 2nd class cabins (AB4nb), three large 2nd class cabins (B4nb) and two large 2nd class cabins and baggage compartment with space for the train conductor (BD4nf). Although prototypes had also been trialled with side panels made from aluminium, standard steel and corrugated side walls, metal panelling made from stainless steel (V2A) was eventually chosen for mass production. Since the coach paintwork corrosion protection was not required for this material, the n-coaches were abraded under the windows using a peacock eye pattern. This abrading pattern and the silver surface of the V2A quickly earned the n coach the distinctive nickname “Silberlinge”. Except for a few models fitted with lightweight design Minden-Deutz bogies, the n-coaches were fitted with block brakes (MD42), which were replaced with disk brakes (MD43) in later series. In order to change passengers as quickly as possible, the otherwise common end entrances were abandoned and positioned approximately a third of the way along the coach as double entrances with hinged-folding doors. The basic design of the n-coach proved so successful that between 1960 and 1980 a total of about 5000 coaches were constructed by different coach manufacturers as well as at the Karlsruhe and Hannover refurbishment facilities (Aw). At first, conditions in the extremely cramped conductor’s space in the BD4nf were less than ideal, and it was soon nicknamed the “rabbit hutch” by staff, leading to discontent and safety concerns. As a result, Aw Karlsruhe rebuilt the conductor’s cab, producing a control car in 1972 with a fully-fledged conductor’s cab without any through access to the next coach. These changes meant that the Karlsruhe version differed significantly from the previous “rabbit hutch” with its passageway between the coaches. From the mid-1980s, the Federal Railways started to modernise coaches that were in some cases already 20 years old. Following several design studies, the positive features of the individual programmes were combined at Aw Hannover in the new Hannover design. New features also consisted of the mint green paintwork or new sliding windows with plastic frames. This design, which was also installed by PFA Weiden or OFV Verona using alternative interior colours, can still be found in modern n-coaches that have been painted in the DB AG corporate colours. Other conversions were performed on the control cars. The two designs that had been introduced earlier were only suitable for either diesel or electric traction, depending on the control panel installed. For this reason, a new conductor’s cab was designed at Aw Wittenberge, based on the DB standard driver’s cab of the BR 111, so that the control cabs could be deployed with greater freedom. Numerous “rabbit hutches” and also Karlsruhe versions were subsequently converted to the Wittenberge model. In order to meet the demand for push-pull trains, DB AG also included standard 2nd class coaches in the conversion programme. Model True to original construction differences on the roof and car bottom Multi-part brake system True to original interior fitting NEM-standard short-coupling Precise replica of roof welds Metal axle holders Finely engraved details

Regular price: CHF 171.40

On order, shipped within 10-15 days

H0 Passenger Coach A5 tmfp SNCF
Brawa 46715 Scale H0
H0 Passenger Coach A5 tmfp SNCF

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Wheelsets in toe bearing Individually mounted axle box cover Brake shoes in wheel plane Extra mounted steps Separately mounted axle brake rod Extra mounted brake system Extra mounted Wendler ventilators True-to-original interior fittings Wheel chocks attached Fine engravings and rivets

Regular price: CHF 74.80

On order, shipped within 10-15 days

H0 Passenger Coach B5 ½ tmfp SNCF
Brawa 46716 Scale H0
H0 Passenger Coach B5 ½ tmfp SNCF

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Wheelsets in toe bearing Individually mounted axle box cover Brake shoes in wheel plane Extra mounted steps Separately mounted axle brake rod Extra mounted brake system Extra mounted Wendler ventilators True-to-original interior fittings Wheel chocks attached Fine engravings and rivets

Regular price: CHF 74.80

On order, shipped within 10-15 days

H0 Passenger Coach B6 tnf SNCF
Brawa 46717 Scale H0
H0 Passenger Coach B6 tnf SNCF

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Wheelsets in toe bearing Individually mounted axle box cover Brake shoes in wheel plane Extra mounted steps Separately mounted axle brake rod Extra mounted brake system Extra mounted Wendler ventilators True-to-original interior fittings Wheel chocks attached Fine engravings and rivets

Regular price: CHF 74.80

On order, shipped within 10-15 days

H0 Passenger Coach B6 tmfp SNCF
Brawa 46718 Scale H0
H0 Passenger Coach B6 tmfp SNCF

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Wheelsets in toe bearing Individually mounted axle box cover Brake shoes in wheel plane Extra mounted steps Separately mounted axle brake rod Extra mounted brake system Extra mounted Wendler ventilators True-to-original interior fittings Wheel chocks attached Fine engravings and rivets

Regular price: CHF 74.80

On order, shipped within 10-15 days

H0 Luggage Car D2mep CFL
Brawa 46719 Scale H0
H0 Luggage Car D2mep CFL

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Metal axle holders True to original axle box cover Individually mounted steps Axle brake frame with brake blocks in wheel plane Individually mounted brake systems True to original interior fitting Individually mounted wheelchocks Finely engraved rivets

Regular price: CHF 74.80

On order, shipped within 10-15 days

H0 Standard Corridor Coach AB2mp CFL
Brawa 46720 Scale H0
H0 Standard Corridor Coach AB2mp CFL

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Metal axle holders True to original axle box cover Individually mounted steps Axle brake frame with brake blocks in wheel plane Individually mounted brake systems True to original interior fitting Individually mounted wheelchocks Finely engraved rivets

Regular price: CHF 74.80

On order, shipped within 10-15 days

H0 Standard Corridor Coach B2mp CFL
Brawa 46721 Scale H0
H0 Standard Corridor Coach B2mp CFL

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Metal axle holders True to original axle box cover Individually mounted steps Axle brake frame with brake blocks in wheel plane Individually mounted brake systems True to original interior fitting Individually mounted wheelchocks Finely engraved rivets

Regular price: CHF 74.80

On order, shipped within 10-15 days

H0 Standard Corridor Coach B2mep CFL
Brawa 46722 Scale H0
H0 Standard Corridor Coach B2mep CFL

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Metal axle holders True to original axle box cover Individually mounted steps Axle brake frame with brake blocks in wheel plane Individually mounted brake systems True to original interior fitting Individually mounted wheelchocks Finely engraved rivets

Regular price: CHF 74.80

On order, shipped within 10-15 days

H0 Passenger Coaches Bif-28 / Bi-28 / Bi-28 and Bi-28 DB, set of 4 - Push-pull train
Brawa 46776 Scale H0
H0 Passenger Coaches Bif-28 / Bi-28 / Bi-28 and Bi-28 DB, set of 4 - Push-pull train

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model 1 x Command car 3 x Passenger coach 2nd class Metal axle holders True to original axle box cover Individually mounted steps Axle brake frame with brake blocks in wheel plane Individually mounted brake systems True to original interior fitting Individually mounted wheelchocks Finely engraved rivets Command car with PluX22 interface and triple headlights AC version: Command car with decoder The DC models of the Train's Command Car must be equipped with a function decoder, e.g. FH22-4 (Order No. 0018271.00), for digital operation.

Regular price: CHF 324.80

On order, shipped within 10-15 days

H0 Passenger Coach Bi-28 DB
Brawa 46781 Scale H0
H0 Passenger Coach Bi-28 DB

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Metal axle holders True to original axle box cover Individually mounted steps Axle brake frame with brake blocks in wheel plane Individually mounted brake systems True to original interior fitting Individually mounted wheelchocks Finely engraved rivets

Regular price: CHF 92.85

On order, shipped within 10-15 days

H0 Passenger Coaches Bif-28 / Bi-28 / Bi-28 and Bi-28 DB, set of 4 - Push-pull train
Brawa 46782 Scale H0
H0 Passenger Coaches Bif-28 / Bi-28 / Bi-28 and Bi-28 DB, set of 4 - Push-pull train

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model 1 x Command car 3 x Passenger coach 2nd class Metal axle holders True to original axle box cover Individually mounted steps Axle brake frame with brake blocks in wheel plane Individually mounted brake systems True to original interior fitting Individually mounted wheelchocks Finely engraved rivets Command car with PluX22 interface and triple headlights AC version: Command car with decoder The DC models of the Train's Command Car must be equipped with a function decoder, e.g. FH22-4 (Order No. 0018271.00), for digital operation.

Regular price: CHF 455.65

On order, shipped within 10-15 days

H0 Passenger Coach ABi-28 DB
Brawa 46783 Scale H0
H0 Passenger Coach ABi-28 DB

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Metal axle holders True to original axle box cover Individually mounted steps Axle brake frame with brake blocks in wheel plane Individually mounted brake systems True to original interior fitting Individually mounted wheelchocks Finely engraved rivets

Regular price: CHF 96.50

On order, shipped within 10-15 days

H0 Passenger Coach Bi-28 DB
Brawa 46784 Scale H0
H0 Passenger Coach Bi-28 DB

Prototype The development of the two-axle standard corridor carriages of the “Austauschbauart” (a design based on standardised components) was closely linked to the production of standardised railway components, which emerged as a key industry in the 1920s. The DRG (Deutsche Reichsbahn Gesellschaft) had set itself the goal of having wagon components manufactured on a cross-company basis in accordance with standardised specifications and conditions, in order to drastically reduce the cost of subsequent maintenance at its own works and to ensure the use of interchangeable components. Against this background, the DRG commissioned the Gesellschaft Deutscher Waggonfabriken (D.W.V.) to develop and deliver the required standard corridor carriages. The specification for the standardised wagons of the “Austauschbauart” meant it was no longer necessary to produce around 1,400 drawings for each individual wagon class. Instead, there was now one basic type that provided the basis for the modified designs, which required approximately 150 drawings each. Starting in 1928, almost 5,500 cars of the various classes BCi-28, Ci-28, CDi-29, Pwi-28, Ci-29 BCi-29, Pwi-29, Bi-29 and Ci-30 were produced for passenger transport in several delivery series. These wagons met the expectations of the DRG and meant that many older state railway cars and related classes could be decommissioned. The running characteristics of these coaches, which were not particularly satisfactory for the passengers, soon earned them the well-known nickname “Donnerbüchsen”. The turmoil of the war years inevitably led to the two-axle standard corridor carriages subsequently finding their way into the inventories of many European railway companies. However, they all shared a common fate – by the late 1960s and early 1970s all of these carriages had been removed from the general maintenance stock. The cars that still exist today serve as very popular attractions at various railway museums in Germany and abroad. Model Metal axle holders True to original axle box cover Individually mounted steps Axle brake frame with brake blocks in wheel plane Individually mounted brake systems True to original interior fitting Individually mounted wheelchocks Finely engraved rivets

Regular price: CHF 96.50

On order, shipped within 10-15 days