Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Rolling Stock

Locomotives, multiple units, coaches and wagons, new and pre-owned, from Z to G, checked by modellers.
Filter products
H0 Flat Car Sggrrs VTG
Brawa 51173 Scale H0
H0 Flat Car Sggrrs VTG

Prototype Innofreight, as the name suggests, is fully committed to innovation in rail freight transport. The company claims that its self-developed InnoWaggons allow freight transport on the railways to be organised more efficiently than ever before. Innofreight achieves this efficiency by offering its InnoWaggons in three different lengths: 2x30 ft, 2x40 ft and 2x45 ft. Each vehicle consists of two short-coupled carrying wagons. The InnoWaggons can be fitted with a variety of different superstructures and transport racks by means of standardised folding container spigots. The wagons can thus be individually equipped and loaded for each customer and, if required, even for each transport assignment. This is certainly a very far-sighted innovation, especially given the increasingly complex approval procedures for rail vehicles. Model Replica of all three InnoWaggons double carriages Replica of the latest generation Y25 bogie Extra mounted brake-switch Fine engravings NEM-standard short-coupling True-to-original replica of the car bottom Wheelsets with inside contours Bogie with three-point support Without loading, for free arrangement

Regular price: CHF 112.70

On order, shipped within 10-15 days

H0 Covered Freight Car Glr22 "Löwensenf" DB
Brawa 51177 Scale H0
H0 Covered Freight Car Glr22 "Löwensenf" DB

Prototype The association construction types of the German national railway association already included an open-plan covered freight car, which was used in particular for freight with a high weight and low volume. After the foundation of the DRG, the main standard freight cars were redesigned according to the so-called principles of interchangeability. For this the production tolerances were kept so small that it was very easy to change replacement parts. The design of the new open-plan freight car was heavily based on its association type predecessor. The main dimensions such as wheelbase and length over buffers was adopted, as were the two metre wide doors opening to the right, which however were installed suspended. New features included the riveted strut bracing, which allowed a lower design of the longitudinal beam, and the barrel design of the roof instead of the basket arch of the predecessor cars. Some of the cars had a handbrake with brakeman’s cab and/or variable gauge wheel sets for adaptation to Russian wide gauge, identifiable by the white painted buffer sleeves and the sub-class mark "r". All covered open-plan cars were allocated to the "Dresden" class district. As already mentioned, the cars were particularly suitable for light freight with large volumes (e.g. glass industry). When the design was revised later, a few changes were made, for example longer and softer suspension springs, which allowed higher speeds and therefore also use in passenger trains. Due to the turmoil of the war, not only the two German railway administrations but also many other European railways had cars of this type in their stock after 1945. The last ones were only retired in the 1980s - proof of the quality and durability of the design. Model Axle holders made of embossed sheet metal Individually mounted wheelchocks Fine replica of the wheel bearing Individually mounted brake switch NEM-standard short-coupling True to original car bottom Wheelsets with inside contours

Regular price: CHF 49.55

On order, shipped within 10-15 days

H0 Covered Freight Car Gmhs SNCB
Brawa 51183 Scale H0
H0 Covered Freight Car Gmhs SNCB

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Gms "HO Handelsorganisation" DR
Brawa 51185 Scale H0
H0 Covered Freight Car Gms "HO Handelsorganisation" DR

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Gmh35 "Tchibo" DB
Brawa 51186 Scale H0
H0 Covered Freight Car Gmh35 "Tchibo" DB

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Gmhs35 "Ritter Sport" DB
Brawa 51188 Scale H0
H0 Covered Freight Car Gmhs35 "Ritter Sport" DB

Prototype Ritter Sport is now known and loved not only in Germany, but all over the world. In 1912, Clara and Alfred Eugen Ritter founded the company in Stuttgart-Bad Cannstatt. Thanks to a suggestion by Clara Ritter, the iconic square chocolate was introduced in 1932. This innovative shape was not only practical for transportation, but is still a trademark that sets Ritter Sport apart from other chocolate manufacturers today. “Square. Practical. Good.” – describes not only the characteristic shape of the chocolate, but also the practical advantages and high quality of the products. The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Gms "Rotkäppchen" DR
Brawa 51189 Scale H0
H0 Covered Freight Car Gms "Rotkäppchen" DR

Prototype Rotkäppchen Sektkellerei has its origins in Freyburg an der Unstrut in 1856. Founded by brothers Moritz and Julius Kloss together with their friend Carl Foerster, Sektkellerei Kloss und Foerster specialized in the production of sparkling wines. Due to a new law in 1894, the iconic red capsule became the new brand name. “Rotkäppchen Sekt” became one of the first German brands to be registered and still exists today. The company is now part of the Rotkäppchen-Mumm Group and stands for tradition, quality, and enjoyment. The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Gmhs35 "Bosch" DB
Brawa 51191 Scale H0
H0 Covered Freight Car Gmhs35 "Bosch" DB

Prototype Bosch was founded in Stuttgart in 1886 by Robert Bosch. Initially, the company focused on the manufacture of electrical engineering and automotive parts. Even in its early years, Bosch developed innovative products, including spark plugs for cars. Over time, the company expanded worldwide and became one of the leading suppliers of automotive technology, industrial electronics, and household appliances. Today, Bosch is known for its quality, innovations, and its role as a major global technology group. The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Glms201 DB
Brawa 51193 Scale H0
H0 Covered Freight Car Glms201 DB

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Nm K.P.E.V.
Brawa 51242 Scale H0
H0 Covered Freight Car Nm K.P.E.V.

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car Gm K.Sächs.Sts.E.B.
Brawa 51243 Scale H0
H0 Covered Freight Car Gm K.Sächs.Sts.E.B.

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car Gm GOS
Brawa 51244 Scale H0
H0 Covered Freight Car Gm GOS

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car G DRG
Brawa 51245 Scale H0
H0 Covered Freight Car G DRG

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car G DRG
Brawa 51246 Scale H0
H0 Covered Freight Car G DRG

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car G 02 "Brake Carriage" DB
Brawa 51247 Scale H0
H0 Covered Freight Car G 02 "Brake Carriage" DB

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car G10 DB
Brawa 51248 Scale H0
H0 Covered Freight Car G10 DB

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car G10 DB
Brawa 51249 Scale H0
H0 Covered Freight Car G10 DB

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car G DR
Brawa 51250 Scale H0
H0 Covered Freight Car G DR

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car G ÖBB
Brawa 51251 Scale H0
H0 Covered Freight Car G ÖBB

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car Z CSD
Brawa 51252 Scale H0
H0 Covered Freight Car Z CSD

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car Gklm191 DB
Brawa 51253 Scale H0
H0 Covered Freight Car Gklm191 DB

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Covered Freight Car (Gw) G DR
Brawa 51254 Scale H0
H0 Covered Freight Car (Gw) G DR

Prototype The Deutsche Staatsbahnwagenverband (DWV), founded in 1909, developed the A2 standard wagon based on the existing state-railway covered goods wagons, featuring a 4.5 m wheelbase and a 15-tonne load capacity. From 1911 onwards, this design was produced as numerous series for the Länderbahnen (state railways), private railways and later the Reichsbahn (National Railway). By 1934, an astonishing total of 121,770 wagons of this type, designated G Kassel/Munich, had been delivered to the Deutsche Reichsbahn Gesellschaft alone. Including wagons built for private and foreign railways, it is estimated that more than 160,000 wagons were manufactured based on the A2 master drawing. From 1938 onwards, these wagons were reinforced to withstand the additional stresses caused by the installation of air brakes as well as increased speeds. Diagonal struts were welded into the end sections, and in some cases, the end stanchions were rotated by 90 degrees. By the end of 1952, 35,600 wagons of this type, now designated as G10, were still in service with Deutsche Bundesbahn. Over time, the inventory steadily diminished due to conversions to Gms54 wagons, general fleet modernisation and the resulting decommissioning. In 1976, the last wagon of this type, now designated as Gklm191, was withdrawn from the maintenance fleet. However, many of these wagons remained in use as station or workshop vehicles. Model Finer board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Beer Car "Dortmunder Union" DB
Brawa 51255 Scale H0
H0 Beer Car "Dortmunder Union" DB

Prototype Beer was one of the first goods to be transported on our railways. Breweries commissioned their own insulated wagons, which were incorporated into the railway companies’ fleets for operational purposes. Due to the small production batches, these wagons were rarely identical but generally conformed to the dimensions of standard goods wagons built by the various state and national railways. It is hardly surprising, then, that the beer transport wagons were yet another iteration of the A2 wagon type master drawing. The original wagon that served as the inspiration for BRAWA’s new model features vertically mounted wooden cladding that conceals the body frame, increasing the width of the wagon body. In this design, as well as slightly modified variants, these beer wagons were used by many breweries between 1910 and 1970. Model Vertical board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days

H0 Beer Car "Adler-Brauerei Bielstein" DRG
Brawa 51256 Scale H0
H0 Beer Car "Adler-Brauerei Bielstein" DRG

Prototype Beer was one of the first goods to be transported on our railways. Breweries commissioned their own insulated wagons, which were incorporated into the railway companies’ fleets for operational purposes. Due to the small production batches, these wagons were rarely identical but generally conformed to the dimensions of standard goods wagons built by the various state and national railways. It is hardly surprising, then, that the beer transport wagons were yet another iteration of the A2 wagon type master drawing. The original wagon that served as the inspiration for BRAWA’s new model features vertically mounted wooden cladding that conceals the body frame, increasing the width of the wagon body. In this design, as well as slightly modified variants, these beer wagons were used by many breweries between 1910 and 1970. Model Vertical board joints Three-point support Multi-part Kkg brake system True to original frame construction Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover

Regular price: CHF 42.35

On order, shipped within 10-15 days