Track
Pier set for up and down ramp, 12 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Pier extension set for up and down ramp, 12 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Piers 50 mm, 5 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Fishplates, 20 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Insulated fishplates, 20 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Rocker for fixing bridges and viaducts (20 pieces). By Kato, N gauge.
On order, shipped within 4-5 days
H0 HV21 Variation Set, signal set, 9 pieces. By Kato, H0 gauge.
On order, shipped within 4-5 days
Kit. Modern rail cranes are used all over the world, most of the time in the construction and maintenance of the local railway tracks, but often also in case of accidents. In far-off countries, these cranes belonging to the rail maintenance cars are generally transported by sea. Due to their high total weight in service order of over 100 t they are usually transported divided in upper and lower part to the port and are reassembled only at the point of destination. This vehicle transports the superstructure of a rail crane. The undercarriage is transported by item 13601. With high quality pad printing. L 26.0 x W 3.5 x H 4.5 cm Level of difficulty: 2 (advanced)
On order, lead time to be confirmed
Kit. This vehicle transports the undercarriage of a rail crane. The superstructure is transported by item 13600. With high quality pad printing. L 25.7 x W 3.3 x H 4.0 cm Level of difficulty: 2 (advanced)
On order, lead time to be confirmed
Functional kit. With pre-assembled front and rear lighting and yellow flashing light. Used for mending and maintenance work on catenary wire systems. With high quality pad printing. L 7.5 x W 3.3 – 5.0 x H 4.2 cm / Crane boom fully tilted 8.8 cm Level of difficulty: 2 (advanced)
On order, lead time to be confirmed
Kit. Level of difficulty: 1 (beginners)
On order, lead time to be confirmed
G1 straight track, length 444.12 mm
On order, lead time to be confirmed
Compensating section. Together with the curved track R10 (45025), the opposing curve can be built for the simple points and the double crossover.
On order, lead time to be confirmed
Flexible track section for any radii. Supplied without fishplates.
On order, lead time to be confirmed
Standard curve R1. The angle is 22.5°, the radius is 914.4 mm. 16 track pieces are required to form a circle.
On order, lead time to be confirmed
Parallel curve R2. The angle is 22.5°, the radius is 1028.7 mm. This results in a track spacing to R1 of 114.3 mm. A circle requires 16 track pieces.
On order, lead time to be confirmed
Parallel curve R2. The angle is 7.5°, the radius is 1028.7mm. 2 pieces complete the 45° curve when using the curved point.
On order, lead time to be confirmed
Curved track for points and DKW. The angle is 11.25°, the radius is 1649.39 mm. 32 track pieces are required to form a circle.
On order, lead time to be confirmed
Point angle 11.25°, length 455.39 mm, radius 1649.39 mm (R10). Supplied with a point lever, it can be upgraded to a digitally controllable point using the 45040 point motor.
On order, lead time to be confirmed
Point angle 11.25°, length 455.39 mm, radius 1649.39 mm (R10). Supplied with a point lever, it can be upgraded to a digitally controllable point using the 45040 point motor.
On order, lead time to be confirmed
Point angle 11.25°. Radius of the inner curve 1028.70 mm. The outer curve is a curve with a continuously changing radius. It begins at the point blade with 1786.89 mm and ends with 1540.00 mm. Supplied with a point lever, it can be supplemented with the 45040 drive to become a digitally controllable point.
On order, lead time to be confirmed
Point angle 11.25°. Radius of the inner curve 1028.70 mm. The outer curve is a curve with a continuously changing radius. It begins at the point blade with 1786.89 mm and ends with 1540.00 mm. Supplied with a point lever, it can be supplemented with the 45040 drive to become a digitally controllable point.
On order, lead time to be confirmed
Double turnout (three-way point) 11.25°, with point lever, length 586 mm, radius 1649.39 mm (R10). Supplied with point lever, can be upgraded to a digitally controllable point using two 45040 point motors.
On order, lead time to be confirmed
The point motor can be controlled digitally or analogously. The motor can be mounted on points using the control lever 49035. Dimensions 46 x 33 x 8 mm (without lantern)
On order, lead time to be confirmed