Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Accessories

Filter products
14% off the recommended price
230 Volt Safety Transformer. 32 VA
Märklin 66471 Scale H0
230 Volt Safety Transformer. 32 VA

Model Track voltage adjustable between 4 and 16 V. Lighting voltage 16 V. Plastic housing. Dimensions 120 x 140 x 80 mm. On/off switch on the mains cable. VDE approved. The 32 VA safety transformer is suitable only for enclosed rooms. Note Tested safety. We guarantee the flawless operation of our trains only with original Märklin transformers. The transformers must be protected against moisture and are not approved for outdoor operation. Connect to AC only. Please also observe the operating instructions for the units. Multi-train operation with separate circuits. If several trains are to be operated independently of one another in conventional running, the layout is divided into several circuits. A transformer and at least one feeder track are assigned to each circuit, which is simply separated electrically from the other circuits by a centre conductor insulation (74030, 5022 or 7522). In the Märklin H0 system the rails are at the same potential everywhere and do not have to be interrupted. Circuits can be closed routes such as most main lines, but also other track sections with independent operation. Branch lines, station areas, sidings, shunting areas or locomotive depots lend themselves to this. This also makes it possible to control additional locomotives individually at the same time as fully automatic operation on the line. The catenary of electrified sections of line is as a rule also connected to its own transformer as an additional circuit in each case. This even allows the locomotives used in catenary operation to be controlled independently of the vehicles supplied via the centre conductor. Several catenary circuits are to be separated by the 7022 insulating contact wire section. Power consumption of locomotives and accessories. The output power indicated on the transformer (in VA) is available for the power consumption of all loads in the circuit. Here are some sample calculations: under load, smaller locomotives (e.g. tank locomotive 30001 or similar) require about 9 VA, larger locomotives (e.g. diesel locomotive 33803) about 12 VA. The power consumption of the train lighting depends on the light bulbs installed and is usually below 2 VA per coach. After deducting the power required at the track, the remaining reserve of the transformer can be used at the lighting output for electrical accessories. Here light bulbs consume between 0.5 and 1 VA (see the table "Light bulbs for accessories") and point or signal motors about 6 VA when switching. Further electrical accessories are to be connected to additional lighting transformers. The 66471 safety transformer is not a children's toy.

Selling price: CHF 136.00 RRP CHF 159.00

In stock: 2 on the shelf, shipped within 1-3 days

14% off the recommended price
Z Power Pack with 230 Volt Current Supply
Märklin 67013 Scale Z
Z Power Pack with 230 Volt Current Supply

Finely stepped speed control for smooth starting and powerful acceleration up to top speed. Single-knob operation for setting the track voltage and determining the direction of travel by turning the control knob out of the centre position. Dimensions of the controller 130 mm (L) x 70 mm (W) x 50 mm (H).

Selling price: CHF 110.00 RRP CHF 129.00

In stock: 2 on the shelf, shipped within 1-3 days

11% off the recommended price
Tool Set
Märklin 70900 Scale H0
Tool Set

Suitable for servicing H0 and Z models. Contents: 1 each of the Phillips screwdrivers PH 00, PH 0 and PH 1. 1 each of the slotted screwdrivers 2.0 mm and 3.0 mm. 1 each of the hex screwdrivers 2.5 mm, 3.0 mm and 3.5 mm. 1 pair of tweezers and 1 pair of cross-locking tweezers.

Selling price: CHF 24.90 RRP CHF 27.99

In stock: 2 on the shelf, shipped within 1-3 days

12% off the recommended price
Gray Wire
Märklin 7100 Scale H0
Gray Wire

Single-core. Grey. 10 m. Cross-section 0.19 mm².

Selling price: CHF 4.10 RRP CHF 4.69

In stock: 2 on the shelf, shipped within 1-3 days

12% off the recommended price
Blue Wire
Märklin 7101 Scale H0
Blue Wire

Model The Märklin 7101 cable (blue) is the ideal solution for clean and reliable wiring of your model railway layout. With a length of 10 metres, a 0.19 mm² cross-section and single-core construction, it is perfectly suited to common return leads, accessories or lighting – universally usable for all gauges. Single-core. Blue. 10 m. Cross-section 0.19 mm². Highlights 10 m connecting cable in blue, single-core, 0.19 mm² cross-section Universally usable for all gauges and systems (analogue & digital) Ideal for common return leads as well as accessories, points and lighting Flexible and long-lasting insulation for easy laying even on complex layouts Clear colour coding for tidy and safe wiring

Selling price: CHF 4.10 RRP CHF 4.69

In stock: 2 on the shelf, shipped within 1-3 days

12% off the recommended price
Red Wire
Märklin 7105 Scale H0
Red Wire

Model The Märklin 7105 cable (red) is the ideal solution for clean and reliable wiring of your model railway layout. With a length of 10 metres, a 0.19 mm² cross-section and single-core construction, it is perfectly suited to common return leads, accessories or lighting – universally usable for all gauges. Single-core. Red. 10 m. Cross-section 0.19 mm². Highlights 10 m connecting cable in red, single-core, 0.19 mm² cross-section Universally usable for all gauges and systems (analogue & digital) Ideal for common return leads as well as accessories, points and lighting Flexible and long-lasting insulation for easy laying even on complex layouts Clear colour coding for tidy and safe wiring

Selling price: CHF 4.10 RRP CHF 4.69

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Brown Plugs, pack of 10
Märklin 71411 Scale H0
Brown Plugs, pack of 10

Model Pack with 10 pieces. Note The plugs and sockets cannot be combined with the earlier version (pack item no. 7130). The sockets fit with limitations into the jacks of control panels and switch panels of the earlier version. The controllers and decoders in the current Märklin range have been converted to the new standard.

Content: 10 pc. (CHF 0.49 / 1 pc.)

Selling price: CHF 4.90 RRP CHF 5.69

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Yellow Plugs, pack of 10
Märklin 71412 Scale H0
Yellow Plugs, pack of 10

Model Pack with 10 pieces. Note The plugs and sockets cannot be combined with the earlier version (pack item no. 7130). The sockets fit with limitations into the jacks of the earlier version of control panels and switch panels. Many controllers and decoders in the Märklin range have already been converted to the new standard today.

Content: 10 pc. (CHF 0.49 / 1 pc.)

Selling price: CHF 4.90 RRP CHF 5.69

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Orange Plugs, pack of 10
Märklin 71414 Scale H0
Orange Plugs, pack of 10

Model Pack of 10 pieces. Note The plugs and sockets cannot be combined with the earlier version (pack item no. 7130). The sockets fit with limitations in the jacks of the earlier version of control panels and switch panels. Many controllers and decoders in the Märklin range have today already been converted to the new standard.

Content: 10 pc. (CHF 0.49 / 1 pc.)

Selling price: CHF 4.90 RRP CHF 5.69

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Red Plugs, pack of 10
Märklin 71415 Scale H0
Red Plugs, pack of 10

Model Pack of 10 pieces. Note The plugs and sockets cannot be combined with the earlier version (pack item no. 7130). The sockets fit with limitations in the jacks of the earlier version of control panels and switch panels. Many controllers and decoders in the Märklin range have today already been converted to the new standard.

Content: 10 pc. (CHF 0.49 / 1 pc.)

Selling price: CHF 4.90 RRP CHF 5.69

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Yellow Sockets, pack of 10
Märklin 71422 Scale H0
Yellow Sockets, pack of 10

Model Pack of 10 pieces. Matching the standard plugs and sockets from the 71400 assortment. Note The plugs and sockets cannot be combined with the earlier version (pack item no. 7130). The sockets fit with limitations in the jacks of control panels and switch panels of the earlier version. The controllers and decoders in the current Märklin range have been converted to the new standard.

Content: 10 pc. (CHF 0.49 / 1 pc.)

Selling price: CHF 4.90 RRP CHF 5.69

In stock: 2 on the shelf, shipped within 1-3 days

12% off the recommended price
Close Couplers, pack of 50
Märklin 7203 Scale H0
Close Couplers, pack of 50

Contents: 50 close coupler heads 701630. For fitting in vehicles with a standard coupler pocket (NEM 362) and a guide mechanism. Compatible with standard couplers (NEM 360).

Content: 50 pc. (CHF 1.12 / 1 pc.)

Selling price: CHF 55.90 RRP CHF 63.99

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Smoke Unit Kit, Diameter 5 mm / 3/16"
Märklin 7226 Scale H0
Smoke Unit Kit, Diameter 5 mm / 3/16"

Consisting of a smoke insert, a replacement steam pipe, a cleaning wire and tweezers. Installation from above.

Selling price: CHF 25.90 RRP CHF 29.99

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Braking Module
Märklin 72442 Scale H0
Braking Module

Model A signal drive with an integrated circuit for the controlled stopping of digital locomotives with a high-performance motor. Connections for a two-aspect colour light signal, for the 3 track sections required for stopping the locomotive safely. The brake module is switched either by means of a k 83 decoder or by means of a conventional control panel 7272/72720. Dimensions 100 x 54 x 22 mm. The brake module requires 3 insulated sections of line in the signal area. The first part is a transition area corresponding to the length of a ski pickup shoe (approx. 70-90 mm). The second section is the actual braking area, in which the locomotive comes to a controlled stop. The length of the braking distance is determined by the setting of the braking delay on the locomotive decoder. This second area should be at least 40-50 cm. The third section is a safety section, in which the track voltage is switched off as before in signal sections. This rules out the locomotive accidentally "overrunning" beyond the signal area. The brake module is suitable for colour light signals and semaphore signals. Locomotives with unregulated digital or Delta electronics installed will stop partly in the braking section or only in the safety section. No definite specification is possible. The use of the 72442 brake module together with unregulated drives is therefore less advisable. Note All connections with new click connections. The function corresponds to that of the 72441 brake module.

Selling price: CHF 68.90 RRP CHF 79.99

In stock: 2 on the shelf, shipped within 1-3 days

12% off the recommended price
Control Box
Märklin 72720 Scale H0
Control Box

Model For switching 4 twin-coil solenoid accessories such as points and signals or up to 8 uncoupler tracks. The position set is indicated by the position of the respective buttons. With 8 sockets on the back and 2 on the side. All of the connections are for the new plugs from the 71400 set. 8 matching plugs are included. Dimensions 80 x 40 mm. Highlights All of the connections with new plug connections. Matching plugs are included Function corresponds to the 7272 unit

Selling price: CHF 21.90 RRP CHF 24.99

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Lighting Kit
Märklin 73150 Scale H0
Lighting Kit

For the 43200, 43201, 43206, 43210, 43211, 43221, 43226, 43231, 43240, 43300, 43301, 43601, and 43602 coaches. Consisting of a power feed, a lighting strip with lamp sockets, 2 light bulbs, and a current-conducting close coupler.

Selling price: CHF 25.90 RRP CHF 29.99

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Lighting Kit with LEDs for "Donnerbüchsen" / "Thunder Boxes"
Märklin 73300 Scale H0
Lighting Kit with LEDs for "Donnerbüchsen" / "Thunder Boxes"

Model Circuit board with several warm white LEDs (2700k), suitable for the "Donnerbüchsen" coaches with the 4313 / 4314 / 4315 basis in the Märklin H0 programme. Anti-flicker capacitor for consistently bright light integrated. Mounting hardware is included. For "Donnerbüchsen" with the 4313 / 4314 basis (seating coaches) the 73301 power supply is additionally required. For "Donnerbüchsen" with the 4315 basis (baggage coach) the 73302 power supply is additionally required. Highlights Anti-flicker capacitor for consistently bright light integrated Note This product was created in cooperation with the firm Viessmann Modelltechnik GmbH.

Selling price: CHF 16.90 RRP CHF 19.49

In stock: 2 on the shelf, shipped within 1-3 days

Pickup Set for Coaches
Märklin 73301 Scale H0
Pickup Set for Coaches

Model Power feed for the 73300 interior lighting for "Donnerbüchsen" with the 4313 / 4314 basis (seating coaches). With a pickup shoe and a return spring. Mounting hardware is included. Note This product was created in cooperation with the firm Viessmann Modelltechnik GmbH.

Selling price: CHF 11.90 RRP CHF 12.99

In stock: 2 on the shelf, shipped within 1-3 days

12% off the recommended price
Cold White LED Lighting Kit
Märklin 73411 Scale H0
Cold White LED Lighting Kit

Model Universal circuit board with several LEDs for retrofitting most of the coaches in the Märklin H0 range. A built-in buffer capacitor allows flicker-free operation. The brightness of the interior lighting can be adjusted manually. The circuit board can be shortened at several places for shorter coaches. Retaining clips for mounting on the interior details are included. Highlights Bright light in the coach: white LEDs. Flicker-free operation thanks to a buffer capacitor Adjustable brightness for the interior lighting

Selling price: CHF 21.90 RRP CHF 24.99

In stock: 2 on the shelf, shipped within 1-3 days

14% off the recommended price
Feeder Wire Set with Interference Suppressor
Märklin 74046 Scale H0
Feeder Wire Set with Interference Suppressor

With radio interference suppression and overload protection. Circuit board with flat plugs for C tracks and red and brown connecting cables. One is required in each conventional circuit. To protect against possible radio interference when locomotives are operated, the 74046 connection set should be installed once in every circuit. In addition, effective protection against overloads and short circuits is ensured, which also responds very quickly with older transformers. The protective functions are retained when there are additional power feeds in the same circuit with the 74042 additional connection. Suitable for 24188 (straight track).

Selling price: CHF 24.90 RRP CHF 28.99

In stock: 2 on the shelf, shipped within 1-3 days

14% off the recommended price
Installation Digital Decoder for Turnouts (C Track)
Märklin 74466 Scale H0
Installation Digital Decoder for Turnouts (C Track)

Can be retrofitted to the C track three-way point (24630) with an electric point motor. Digital formats mfx, Motorola, and DCC. Connection by means of plug contacts, for Märklin and Trix C track three-way points. The address can be set both with the coding switch (MM 1–320, DCC 1–511) and via CV (MM 1–320, DCC 1–2044) using the programming track. A point lantern can also be controlled; soldering skills are required for this connection. A digital decoder can be fitted to the electric point motor at the same time or later. The decoder is simply connected with plug contacts and can be addressed individually for each point. The digital power supply can be taken directly from the traction current contact on the point. In this way you get a ready-made digital point that is immediately operational even on portable layouts.

Selling price: CHF 48.90 RRP CHF 56.99

In stock: 2 on the shelf, shipped within 1-3 days

11% off the recommended price
Digital Installation Double Slip Switch Decoder (C Track)
Märklin 74467 Scale H0
Digital Installation Double Slip Switch Decoder (C Track)

For retrofitting a slim C track double slip point 24720 or Trix 62720. Digital formats mfx, Motorola, and DCC. Connection by means of plug contacts. The address can be set both with the coding switch (MM 1–320, DCC 1–511) and via CV (MM 1–320, DCC 1–2044) using a programming track. A 74477 point lantern (not included in the contents supplied) can also be controlled.

Selling price: CHF 38.90 RRP CHF 43.99

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Spade Connectors, pack of 20
Märklin 74995 Scale H0
Spade Connectors, pack of 20

Model The Märklin 74995 flat plug sleeves are the perfect accessory for safe, reliable wiring of your Märklin C track. The high-quality metal sleeves let you make stable electrical connections – quickly, easily and without any additional tools. Suitable for the contact tabs on the C track. For all Märklin cables from 0.19 mm² to 0.75 mm² cross-section. Contents 20 pieces. Highlights Set of 20 flat plug sleeves, specially for the Märklin C track system Easy mounting – slide onto the contacts without tools High conductivity thanks to the robust metal version Reliable power supply for all C tracks (standard, contact and point tracks) Long-lasting and reliable – ideal for the assembly and expansion of any layout

Content: 20 pc. (CHF 0.28 / 1 pc.)

Selling price: CHF 5.50 RRP CHF 6.39

In stock: 2 on the shelf, shipped within 1-3 days

12% off the recommended price
Locomotive Magnets, pack of 3
Märklin 7557 Scale H0
Locomotive Magnets, pack of 3

3 pieces. 13 x 7 x 2.5 mm. For actuating the 7555 switching contact. For locomotives with greater ground clearance.

Content: 3 pc. (CHF 4.97 / 1 pc.)

Selling price: CHF 14.90 RRP CHF 16.99

In stock: 2 on the shelf, shipped within 1-3 days