Accessories
Adapter board, 18-pin Next-18 socket to PluX12, Flex, 88mm This adapter board can be docked to all decoders with a Next18 connection and offers a PluX12 interface on the locomotive side. In particular, TT locomotives from Tillig can now be easily converted with our LokSound 5 micro Next18 or LokPilot 5 micro Next18. The flex circuit board can be folded and extended to almost any length. The adapter board comes with shrink tubing and speaker connection cables. Art.No. Delivery 51997 Adapter board, 18-pin Next-18 socket to PluX12, Flex, 88mm
On order, shipped within 4-5 days
Adapter board 21MTC to Next18, for certain Liliput engines This small adapter board is a practical helper for equipping some models (e.g. from Liliput) with a LokSound decoder: A 21MTC interface was installed there, but the required length for a LokSound 5 decoder was not taken into account. With the help of this adapter board, a LokSound 5 micro can be used horizontally in the available installation space. If the width is 21mm, these locomotives can now also be easily converted to LokSound. Dimensions with LokSound 5 micro 58818 plugged in: total width 21.5mm x 19mm length. Art.No. Delivery 51998 Adapter board 21MTC to Next18, for certain Liliput engines 51998 with 58818
On order, shipped within 4-5 days
Adapter board Next18 for 6 amplified outputs. With soldering pads and wires The Next18 adapter board is suitable if you want to digitize a very small locomotive without a digital interface, but do not want to freely wire the decoder. With dimensions of only 13.0 mm x 9.0 mm, the board is extremely small and also has a break-off fastening tab. For the functions AUX3 and AUX4, which are designed as logic outputs on the decoder according to the standard, power amplifiers (approx. 180mA each) are on board. A total of up to 6 outputs can be used. Already soldered connection cables with a length of approx. 20 cm for the most important contacts ensure easy handling and wiring. Dimensions: Length 13.0 mm x 9.0 mm (With mounting tongue: 18.0 mm x 9.0 mm). Art.No. Delivery 51999 Adapter board Next18 for 6 amplified outputs. With soldering pads and wires
On order, shipped within 4-5 days
LokProgrammer unit, power supply, manual, USB adapter (Dimensions: 95mm x 85mm x 22mm (3.74 inch x 3.35 inch x 0.87 inch) You want to listen to the sound spectrum of your favourite loco, or the special sound of that loco around the corner in the yard – on your model railroad? No problem with ESU’s LokProgrammer! This versatile device puts the power of realistic sound reproduction directly into your hands, transforming your model railroad experience. With the LokProgrammer, you can easily load custom sound projects onto ESU decoders, enabling your locomotives to reproduce the most authentic sounds. Whether you seek the powerful chuff of a steam giant, the distinctive growl of a diesel, or the specific horn of a chosen prototype, this tool unlocks those auditory possibilities. The intuitive LokProgrammer software interface allows you to select from an extensive library of pre-made high-quality sound files or even import your own meticulously recorded audio. You gain granular control over volume levels, the activation of individual sound elements, and the fine-tuning of engine characteristics to match prototype behavior. Picture precisely adjusting the diesel prime mover on a modern locomotive or the rhythmic exhaust beat of a vintage steam engine. The LokProgrammer empowers you to personalize every nuance, ensuring your models sound as unique and authentic as they appear. This unparalleled level of customization adds a profound layer of immersion to your miniature railway world. Program the decoder while it is installed in the locomotive or connect it to our Decoder Tester and program prior to installation. Sound customization is accessible and easy for everyone. Embrace the ultimate in model railroad sound realism and let your favorite locomotives truly come alive with ESU's groundbreaking LokProgrammer. Change the sound saved on the decoder. Setting of all digital parameters of the Loksound decoder such as address of the loco, operation speed, maximum speed, braking deceleration, brightness of lights etc; you can set all options with your computer very easily - no cumbersome entering of CVs (configuration variables) with your command station. Rearrange your sounds and transfer it to the LokSound decoder. You can use all sounds that can be downloaded to your computer hard disk. Sound can be allocated to different events. Additional sounds can be activated via function buttons. Sound With the LokProgrammer you can replace the sound data of any LokSound decoder as many times as you wish with a different sound. To this end we offer more than 200 different, fully matching sounds of various prototypes and locos for downloading on your computer. Also you can edit just parts of a sound project: You don’t like the horn/whistle? Just replace it with one of the many others. Suitable sources beside those offered by us, are available in Windows *.wav format. Sound – even your voice or music is no problem for our decoders. With the LokProgrammer’s aid you use the entire flexibility and functionality offered by LokSound decoders. Programming By the same token, all other ESU decoders profit from the LokProgrammer’s versatility; no matter if DCC, Multiprotocol - or mfx decoder. With its help it’s possible to edit all parameters of the particular decoder simply and conveniently. The available options depend on the kind of decoder. Besides addresses and acceleration / deceleration settings, this concerns above all the allotment of function keys (function mapping), the allocation of special effects to the individual outputs, or the lamp brightness. The LokProgrammer can also help when optimizing back EMF parameters or the loadable speed table. All options can be programmed very conveniently: There is no tedious punching-in of CV-numbers at the digital station anymore. Hook up It’s this simple: The LokProgrammer is a small stand-alone programming box, it does not interface or connect to any DCC command station. It gets wired between the PC and a dedicated LokProgrammer programming track. To connect it you use the included USBadapter cable. For power we include a 500 mA wall power supply. If your needs are greater (e.g. for gauge I engines), you can also use a conventional model railroad transformer with max 20V DC output. Software After hook-up you start up the especially user-friendly LokProgrammer software. This runs on all modern Windows-systems (Windows 8.1 and higher). Just put a locomotive with an ESU decoder on a dedicated piece of track connected to the LokProgrammer, and right away you can read, edit or program it. The Programmer automatically recognizes the decoder in the locomotive, no need to manually select the decoder type! Simplicity The LokProgrammer is recommended not only for the use with ESU "retail" decoders: Many well known model railroad manufacturers factory-furnish their locos with ESU-decoders. The parameters of these decoders can be modified again with the help of the LokProgrammer to suit the needs of your operations. You see, purchasing a LokProgrammer pays off in any case. Upgrades The LokProgrammer can also be instrumental in updating decoders. Almost all ESU decoders are firmware updatable, in case you desire a new software version. To do this, you only need the LokProgrammer and the most current version of the LokProgrammer software. The updates will happen automatically whenever you write sound or data to a LokSound decoder. The future LokProgrammer software is being reviewed continuously. The latest, pertinent version can always be downloaded from our website , or can be installed automatically, through an internet-update function, on your computer.
On order, shipped within 4-5 days
Decoder tester for decoder.NEM651,652,21MTC,PluX22,Next18, Single wires. Coreless motor, LED monitor, 20mm spk., Extension port If necessary, you can add the Decoder Tester Extension to your Profi Decoder Tester: Plugged into the side of the Decoder Tester it enables you to comfortably test all large scale decoders. If you also have to deal with large scale LokSound XL or LokSound L decoders in your workshop, the Profi Decoder Tester Extension is just the right thing for you: You can plug on LokSound XL decoders with multi-pin connectors as well as LokSound L decoders directly and easily test them. The extension module has multi-pin connectors for direct plug-on of the decoder types mentioned above. An LED monitor with 12 LEDs displays the status of all physical function outputs. You may also plug on a second speaker or sensor inputs onto the multi-pin connector for quick and easy testing. Up to four servos may also be plugged on for direct testing. Especially for the LokSound L, connecting pins for a smoke generator have also been added. The Profi Decoder Tester Extension represents the perfect test and programming bench in conjunction with the Profi Decoder Tester, where you can test and program almost all (ESU) decoders quickly and easily. Art.No. Delivery 53900 Decoder tester for decoder.NEM651,652,21MTC,PluX22,Next18, Single wires. Coreless motor, LED monitor, 20mm spk., Extension port 53901 Decoder tester extension for LokSound XL V4.0, LokSound L V4.0 with LED monitor, servo connectors
On order, shipped within 4-5 days
Highly flexible wire, diameter 0.5mm, AWG36, 2A, 10m sleeve, pink colour Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
On order, shipped within 4-5 days
Highly flexible wire, diameter 0.5mm, AWG36, 2A, 10m sleeve, turquoise colour Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
On order, shipped within 4-5 days
Adapter board for LokSound L / LokPilot L, with screw terminals This adapter board ensures the convenient connection of your LokSound 5 L or LokPilot 5 L Decoders. The decoder is inserted directly into the socket strips. On the output side, the most important connections can be contacted directly on robust screw terminals – without soldering! A socket for the optional connection of a SUSI module as well as pin headers for the direct connection of four RC servos complete the equipment.This adapter board allows professional, clean cabling of your locomotive and the decoder can be easily replaced in case of emergency.The adapter board is fastened with screws in the model. Dimensions 76.2 x 26.4 x 11 mm (LxWxH). Art.No. Delivery 53950 Adapter board for LokSound L / LokPilot L, with screw terminals
On order, shipped within 4-5 days
Adapter board for Hübner Schienenbus, 21MTC interface for LokSound or LokPilot Decoders This adapter board is for owners of a Hübner railbus in track 1 (Art. No. 4070 or 4071) thought. There, a LokSound 2 decoder was installed in the motor car on a special adapter, and in the control car a specially made light change decoder was installed. With the help of this adapter you can finally replace these old decoders with a modern LokSound 5 or LokPilot 5 Fx decoder. Insert a decoder with 21MTC snide into the adapter board and then install it in the railbus. Nothing needs to be rewired, all lamps will work correctly. Note: Not suitable for the new edition of the railbus under Märklin® direction. Art.No. Delivery 53951 Adapter board for Hübner Schienenbus, 21MTC interface for LokSound or LokPilot Decoders
On order, lead time to be confirmed
Adapter board, for BLI steam engines with Paragon 3/4 Decoder, 21MTC, with PowerPack With the help of the BLI Paragon 3/4 (P34) adapter board, H0 Scale tender steam locomotives from Broadway Limited (BLI), in which a Paragon 3 or Paragon 4 decoder was factory installed, can finally be equipped with a LokSound 5 decoder without much effort. All you have to do is open the tender, remove the standard Paragon 3 or 4 decoder and install the BLI P34 adapter board. All connections can be made exactly as before: The type and position of all plug connections is exactly like for the factory installed decoder. No soldering work needs to be done. The locomotive tender coupling can also remain. The locomotive itself does not need to be opened. The LokSound 5 decoder can communicate with the electronics built into the locomotive using a serial protocol and directly control all smoke and light functions. An integrated PowerPack ensures uninterrupted operation even on dirty rails. The BLI P34 adapter board requires a LokSound 5 decoder with 21MTC interface. From firmware 5.9.159 this can speak the required protocol instead of SUSI. Appropriate preconfigured sound files will gradually be made available on our website. Art.No. Delivery 53952 Adapter board, for BLI steam engines with Paragon 3/4 Decoder, 21MTC, with PowerPack
On order, lead time to be confirmed
Adapter board, 24-pin E24 socket to open wires, 88mm, heat shrink The E24 adapter board is suitable if you want to digitize a very small locomotive without a digital interface using the LokSound 5 Nano. With dimensions of only 19.6 mm x 8.5 mm, the board is exactly the same size as the decoder itself and therefore only increases the thickness as a “sandwich”. Already soldered connection wires with a length of approx. 88 mm for power pickup, motor and speaker as well as U+, the non-resistor protected powered light outputs FL, RL, AUX1, AUX2, AUX5, and AUX6 ensure easy handling and wiring. Soldering pads AUX7 and AUX8 are powered for additional lights. Soldering pad AUX3 is "PowerPack Control" when used with an ESU 58923 LokSound 5 Nano DCC decoder. Art.No. Delivery 53953 Adapter board, 24-pin E24 socket to open wires, 88mm, heat shrink
On order, shipped within 4-5 days
Adapter board, for Kato USA N WideBody, for E24 Interface This adapter board with dimensions 47.5mm x 14.0mm fits in such Kato (USA) N-gauge locomotives that have a wide body design such as F-units. It replaces the original circuit board and has connection pads for motor and track as well as the function outputs AUX1, AUX2, AUX3, AUX4, AUX5, AUX6, AUX7 and AUX8. Either a LokSound 5 Nano or a LokPilot 5 Nano can be plugged into the E24 interface. Connection pads for an ESU PowerPack are also available of course. Art.No. Delivery 53954 Adapter board, for Kato USA N WideBody, for E24 Interface
On order, shipped within 4-5 days
Adapter board with PowerPack for E24 Interface This adapter board with the dimensions 54.0mm x 17.0mm has an ESU PowerPack ‘On Board’. Although the capacitors protruding at the front and rear make for a total length of 70mm, this adapter board is ideal for converting many American H0 locomotives from Atlas or Athearn, where it replaces the original circuit board. In addition to connection pads for motor and track, there are also pads for the function outputs AUX1, AUX2, AUX3, AUX4, AUX5, AUX6, AUX7 and AUX8. The series resistors for LEDs installed there can be bridged if required. Either a LokSound 5 Nano or a LokPilot 5 Nano can be plugged into the E24 interface. Art.No. Delivery 53955 Adapter board with PowerPack for E24 Interface
On order, shipped within 4-5 days
Adapter board, 18-pin Next-18 socket to RCN-114 MTC14, Flex Using this adapter board with the dimensions 13.5mm x 8.4mm, Minitrix® locomotives with MTC14 interface can finally be equipped with a LokSound decoder at your own discretion: The adapter board is flexible and is plugged directly into the 14MTC socket of the locomotive, on the other side you can use any decoder with Next18, preferably of course the LokSound 5 Nano Next 18. Additional solder pads for speakers and PowerPack are provided as well. Before installation, please check the available space in the locomotive and in particular whether the locomotive housing can still be closed: The ‘sandwich’ of adapter board and LokSound decoder is somewhat thicker than specified in the VHDM standard RCN-114. ESU cannot guarantee that the conversion will work in all affected locomotives. Art.No. Delivery 53956 Adapter board, 18-pin Next-18 socket to RCN-114 MTC14, Flex
On order, shipped within 4-5 days
PowerPack Maxi energy buffer for LokSound L V4.0, LokSound V4.0, LokSound 5 L and LokSound 5, LokPilot 5 and LokPilot 5 L 2x 5F/2.7V The new ESU PowerPack Maxi has been developed as the powerful complement to the LokSound L V4.0 / LokSound 5 L decoder. It can, of course, provided there is sufficient space, also be connected to all LokPilot V4.0, LokSound V4.0, LokSound V4.0 M4, LokPilot 5 or LokSound 5 decoders. It provides uninterrupted power to your locomotive when traversing dirty track and long turnout ladders. All sound, lighting and motor functions are buffered with the aid of two energy storage capacitors enabling your models – subject to the total energy consumption - to continue running for up to three seconds. The PowerPack Maxi incorporates an integral charging circuit controlled by the decoder. Therefore it may be connected even during programming. The charging current is limited in order to avoid an undue load on the booster, in case there are several models in the same booster sector. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). The space requirements of the PowerPack Maxi of about 27.5 mm x 15.7 mm x 13 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Maxi to the decoder. The wires are already soldered to the PowerPack Maxi but must be soldered to the appropriate solder pads of the decoder. Please note that due to technical reasons the PowerPack cannot operate in analogue mode: Buffering is therefore not possible in analogue mode. Art.No. Delivery 54672 PowerPack Maxi energy buffer for LokSound L V4.0, LokSound V4.0, LokSound 5 L and LokSound 5, LokPilot 5 and LokPilot 5 L 2x 5F/2.7V
On order, shipped within 4-5 days
PowerPack MiniXS, energy buffer with MCU for LokPilot 5 / LokSound 5, 6*0.3F/2.7V, 29 x 5.1 x 15mm The ESU PowerPack MiniXS can be wired to all fifth generation ESU decoders (LokSound 5, LokPilot 5, LokPilot 5 Basic). It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (6 x 0.3 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound system. Subject to the energy consumption of your model it may continue to move for up to 1.5 seconds. This extremely flat module is intended for smaller vehicles with moderate power consumption. The PowerPack MiniXS is equipped with a microcontroller and incorporates an charging circuit controlled by the decoder. Therefore it may be connected even during programming. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). The output voltage is adjusted fully automatically to the track voltage by the microcontroller in order to avoid flickering of the lighting when buffering is activated. The space requirements of the PowerPack MiniXS of about 29 mm x 5.1 mm x 15 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack MiniXS to the decoder. Art.No. Delivery 54673 PowerPack MiniXS, energy buffer with MCU for LokPilot 5 / LokSound 5, 6*0.3F/2.7V, 29 x 5.1 x 15mm
On order, shipped within 4-5 days
PowerPack Midi, energy buffer with MCU for LokPilot 5 / LokSound 5, 6*1F/2.7V, 20.8 x 13.8 x 13.4mm The ESU PowerPack Midi can be wired to all fifth generation ESU decoders (LokSound 5, LokPilot 5, LokPilot 5 Basic). It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (6x1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound system. Subject to the energy consumption of your model it may continue to move for up to three seconds. The PowerPack Midi is equipped with a microcontroller and incorporates an charging circuit controlled by the decoder. Therefore it may be connected even during programming. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). The output voltage is adjusted fully automatically to the track voltage by the microcontroller in order to avoid flickering of the lighting when buffering is activated. The space requirements of the PowerPack Midi of about 20.8 mm (L) x 13.8 mm (W) x 13.4 mm (H) must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Midi to the decoder. Art.No. Delivery 54674 PowerPack Midi, energy buffer with MCU for LokPilot 5 / LokSound 5, 6*1F/2.7V, 20.8 x 13.8 x 13.4mm
On order, shipped within 4-5 days
Smoke unit, Dual Mini (Exhaust + Cylinder) (Gauge 0) for LokSound XL device with electronic board Our smoke generator "Dual small" is suitable for vehicles of the nominal sizes gauge G, and 1 but also for smaller vehicles in gauge 0. Both exhaust steam and cylinder steam are integrated in a compact housing. This means that you can finally retrofit your older locomotives with a realistic cylinder steam. The "Dual Small" smoke generator has a common tank that can be filled from above. Two separate fan motors with separate heating and temperature elements ensure a strong steam output. The required control electronics is housed on a separate board, only 36 mm x 19 mm x 5 mm in size, and controls both the amount of smoke and the fan speed regardless of the level or rail voltage. A burn-through in the case of an empty tank is preventable. The control electronics are simply placed between the smoke generator and the locomotive sound decoder in a suitable location in the vehicle. Our LokSound 5 L and LokSound 5 XL are ideal for control, but the previous versions LokSound XL V4.0 or LokSound L V4.0 can also be used. The smoke generator Dual small is 51.5 mm long, 27.5 mm wide and 30.5 mm high and is made of temperature-resistant plastic. Thanks to various, cut-off fastening straps, it should be possible to install it in many locomotives. Art.No. Delivery 54676 Smoke unit, Dual Mini (Exhaust + Cylinder) (Gauge 0) for LokSound XL device with electronic board
On order, shipped within 4-5 days
Smoke unit, Dual (Exhaust + Cylinder) (Gauge 0) for LokSound XL device with electronic board Our new smoke generator "Dual" is suitable for vehicles of the nominal sizes Gauge G, Gauge 1 but also for larger vehicles in Gauge 0. In contrast to the two other smoke generators from ESU, both exhaust steam and cylinder vapor are integrated in one housing. Thus, you can finally retrofit your older locomotives with a realistic cylinder steam. The smoke generator "Dual" has a common tank that can be filled from above. Two separate fan motors with separate heating and temperature elements ensure powerful steam emission. The required control electronics are housed on a separate, only 36 mm x 19 mm x 5 mm board and controls both the amount of smoke and the fan speed regardless of the level or the rail voltage. Burning through when the tank is empty is also prevented. The control electronics are simply placed between the smoke generator and the LokSound decoder at a suitable location. To control our brand new LokSound 5 L and LokSound 5 XL are excellent, but also the previous versions LokSound XL V4.0 or LokSound L V4.0 can be used. The smoke generator Dual is only 59.8 mm long, 32 mm wide (with fastening straps: 38 mm) and 36.6 mm high and made of temperature-resistant plastic. Thanks to various, cut-off fastening straps, it should be possible to install it in many locomotives. Art.No. Delivery 54677 Smoke unit, Dual (Exhaust + Cylinder) (Gauge 0) for LokSound XL device with electronic board
On order, shipped within 4-5 days
Smoke unit, small size (Gauge 0) for LokSound XL V4.0 and LokSound 5 XL Decoder or SUSI For many modellers running their trains in the garden smoke generators are a must. Besides sound reproduced by the LokSound XL decoders one finds the exhaust smoke synchronous with the exhaust chuffs most exciting. Prototype diesel locomotives also make their presence known by clearly visible exhaust fumes. Although our LokSound XL decoder can handle many commercially available smoke generators we would like to recommend our new smoke generators. Both work perfectly with the LokSound XL V4.0 and LokSound 5 decoders. Integral electronics control both the fan and the heating system of the smoke generator. Since we did not forget to include a temperature sensor the amount of smoke is independent of the track voltage. We have also made sure that nothing will burn if the tank is empty. The amount of smoke and the revs of the fan can be determined by the LokSound XL V4.0 decoder. Of course both steam smoke plumes as well as typical diesel exhaust plumes can be realised. The steam exhaust plumes can be synchronised with external triggers or can be determined by the LokSound XL decoder. If you do not wish to use an ESU decoder you may still use the smoke generator: It also accepts commands via the SUSI interface. The small smoke generator (zero track) is 39.2 mm long, 25 mm wide and 29.1 mm high and is made of temperature-resistant plastic. Thanks to various, cut-off fastening straps, it should be possible to install it in many locomotives. Art.No. Delivery 54678 Smoke unit, small size (Gauge 0) for LokSound XL V4.0 and LokSound 5 XL Decoder or SUSI
On order, shipped within 4-5 days
Smoke unit, big size (Gauge G) for LokSound XL V4.0 and LokSound 5 XL Decoder or SUSI For many modellers running their trains in the garden smoke generators are a must. Besides sound reproduced by the LokSound XL decoders one finds the exhaust smoke synchronous with the exhaust chuffs most exciting. Prototype diesel locomotives also make their presence known by clearly visible exhaust fumes. Although our LokSound XL decoder can handle many commercially available smoke generators we would like to recommend our new smoke generators. Both work perfectly with the LokSound V4.0 XL and LokSound 5 decoders. Integral electronics control both the fan and the heating system of the smoke generator. Since we did not forget to include a temperature sensor the amount of smoke is independent of the track voltage. We have also made sure that nothing will burn if the tank is empty. The amount of smoke and the revs of the fan can be determined by the LokSound XL decoder. Of course both steam smoke plumes as well as typical diesel exhaust plumes can be realised. The steam exhaust plumes can be synchronised with external triggers or can be determined by the LokSound XL decoder. If you do not wish to use an ESU decoder you may still use the smoke generator: It also accepts commands via the SUSI interface. The large smoke generator (G gauge) is 57.2 mm long, 29 mm wide and 32.6 mm high and is made of temperature-resistant plastic Art.No. Delivery 54679 Smoke unit, big size (Gauge G) for LokSound XL V4.0 and LokSound 5 XL Decoder or SUSI
On order, shipped within 4-5 days
LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 8-pin NEM652, with loudspeaker 11x15mm, gauge: H0, 0 The LokSound 5 Fx represents a unique feature within the LokSound family: it has NO MOTOR OUTPUT and is specially designed for use in control cars (Cab Cars) or power cars that require sound but lack a motor and thus are not powered themselves. By omitting the motor component, it offers all the sound features of the other LokSound 5 members, yet measures just 21.5mm x 15.5mm. LokSound 5 Fx decoders are offered with an 8-pin NEM652 or 21MTC interface and always come with an 11 x 15 mm "sugar cube" speaker and speaker enclosure kit. Operating Modes Like all family members, the LokSound 5 Fx is a true multi-protocol decoder. It supports the DCC data format as well as Motorola®, Selectrix® and M4. In DCC format, 14, 28, or 128 speed steps are as standard as Short and Long addresses and up to 32 functions. With RailComPlus® technology, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and can be both operated and programmed with compatible digital command stations: Thanks to RailCom®, CV values can be read on the main track with suitable command stations. Auxiliary CVs are available for command stations that can only program the CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses allow the triggering of 16 functions. A built-in programming mode also enables reprogramming with the venerable Control Unit 6021. The M4 protocol allows automatic registration to mfx®-compatible command stations. The LokSound 5 Fx Decoder recognizes the Märklin® brake sections as well as ZIMO® HLU brake commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops when a Selectrix® brake diode is activated. An ABC shuttle train system enables automatic shuttle operation between two stations. The LokSound 5 decoder can be used on analog DC and AC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustment is required. Sound The LokSound 5 Fx decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz, providing hi-fi quality on your layout. There is practically no audible difference from the original recordings. A Class-D audio amplifier with up to 3W output power drives the speakers, which can have an impedance between 4 ohms and 32 ohms. A 128 Mbit sound memory provides sufficient capacity. The volume of all individual sounds can be individually adjusted. The super-flexible sound engine, without a rigid sequence plan, allows for the prototypical simulation of all conceivable rail vehicles. Functions The control car and the power car also have a number of lights to be controlled. Therefore, we equipped the LokSound 5 Fx with 6 powered function outputs for lights. The version with the 21MTC interface has 6 additional outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. NO Motor Control Although the LokSound 5 Fx itself DOES NOT have a motor output, it still "simulates" one. This serves to synchronize with the powered vehicle, where ideally a "full-fledged" LokSound 5 decoder performs its duties. This ensures that the brake squeal occurs simultaneously within a train, or that the lights change direction simultaneously. Operational Safety A PowerPack can be connected to the LokSound 5 Fx to bridge dirty track sections if desired. Protection The outputs are naturally protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 58210 LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 8-pin NEM652, with loudspeaker 11x15mm, gauge: H0, 0 58219 LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 21MTC NEM660, with loudspeaker 11x15mm, gauge: H0, 0
On order, shipped within 4-5 days
LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 21MTC NEM660, with loudspeaker 11x15mm, gauge: H0, 0 The LokSound 5 Fx represents a unique feature within the LokSound family: it has NO MOTOR OUTPUT and is specially designed for use in control cars (Cab Cars) or power cars that require sound but lack a motor and thus are not powered themselves. By omitting the motor component, it offers all the sound features of the other LokSound 5 members, yet measures just 21.5mm x 15.5mm. LokSound 5 Fx decoders are offered with an 8-pin NEM652 or 21MTC interface and always come with an 11 x 15 mm "sugar cube" speaker and speaker enclosure kit. Operating Modes Like all family members, the LokSound 5 Fx is a true multi-protocol decoder. It supports the DCC data format as well as Motorola®, Selectrix® and M4. In DCC format, 14, 28, or 128 speed steps are as standard as Short and Long addresses and up to 32 functions. With RailComPlus® technology, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and can be both operated and programmed with compatible digital command stations: Thanks to RailCom®, CV values can be read on the main track with suitable command stations. Auxiliary CVs are available for command stations that can only program the CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses allow the triggering of 16 functions. A built-in programming mode also enables reprogramming with the venerable Control Unit 6021. The M4 protocol allows automatic registration to mfx®-compatible command stations. The LokSound 5 Fx Decoder recognizes the Märklin® brake sections as well as ZIMO® HLU brake commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops when a Selectrix® brake diode is activated. An ABC shuttle train system enables automatic shuttle operation between two stations. The LokSound 5 decoder can be used on analog DC and AC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustment is required. Sound The LokSound 5 Fx decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz, providing hi-fi quality on your layout. There is practically no audible difference from the original recordings. A Class-D audio amplifier with up to 3W output power drives the speakers, which can have an impedance between 4 ohms and 32 ohms. A 128 Mbit sound memory provides sufficient capacity. The volume of all individual sounds can be individually adjusted. The super-flexible sound engine, without a rigid sequence plan, allows for the prototypical simulation of all conceivable rail vehicles. Functions The control car and the power car also have a number of lights to be controlled. Therefore, we equipped the LokSound 5 Fx with 6 powered function outputs for lights. The version with the 21MTC interface has 6 additional outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. NO Motor Control Although the LokSound 5 Fx itself DOES NOT have a motor output, it still "simulates" one. This serves to synchronize with the powered vehicle, where ideally a "full-fledged" LokSound 5 decoder performs its duties. This ensures that the brake squeal occurs simultaneously within a train, or that the lights change direction simultaneously. Operational Safety A PowerPack can be connected to the LokSound 5 Fx to bridge dirty track sections if desired. Protection The outputs are naturally protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 58210 LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 8-pin NEM652, with loudspeaker 11x15mm, gauge: H0, 0 58219 LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 21MTC NEM660, with loudspeaker 11x15mm, gauge: H0, 0
On order, shipped within 4-5 days
LokSound 5 L DCC/MM/SX/M4 "blank decoder", Pinheader with adapter, gauge: 0 LokSound 5 L is intended for use in all applications where the required power exceeds the limits of LokSound 5. Ideally these are 0 gauge vehicles and also smaller 1 gauge locomotives. Despite its compact dimensions of only 50.8 mm x 25.4 mm x 14 mm it is equipped with a dual speaker output and integral PowerPack. The LokSound 5 is equipped with a multi-pin connector and is supplied ex works with an adapter board featuring solder pads. Operating modes Like all products of the LokSound family the LokSound 5 L is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps and 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Control Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound 5 L decoder supports Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound 5 L will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables automatic commuting between two stations. The LokSound 5 L decoder is also suitable for analogue DC and AC layouts. Sound The LokSound 5 L decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A dual class D audio power amplifier with up to 2-times 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions Every LokSound 5 L decoder has 11 amplified function outputs. On top of that there are another 6 logic outputs, which can, if so desired, control two RC servos or SUSI extension modules. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for the reliable function of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. 4 sensor inputs may be employed in order to trigger functions. Motor control Motor control of the LokSound 5 L has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 L decoder supplies ample current for the motor, namely up to 3.0 A. LokSound 5 L DCC The LokSound 5 L DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Betrieb unter DCC mit RailComPlus®, M4, Motorola® und Selectrix® 32 Funktionen schaltbar (abhängig von der Zentrale) 32-Bit-Prozessor Digitaler Class-„D“-Verstärker mit bis zu 3 W Leistung (LokSound 5 XL: 13 W) Jeder Kanal in 16-Bit-Auflösung und 31250 kHz Samplerate Geräuschspeicher mit 128 Mbit Kapazität Motorregelung mit 50 kHz Taktfrequenz RC-Servos und Susi-Module ansteuerbar 3 neue, individuell einstellbare Bremsregler Zweistufige Schwerlast-Simulation Updatefähig mit ESU-LokProgrammer LokSound 5 L Für die Baugrößen 0 und I Motorstrom 3 A 11 verstärkte Ausgänge für Sonderfunktionen (Total: 17 Ausgänge) Anschlussmöglichkeit für 2 RC-Servos Doppelendstufe zur Ansteuerung von 2 Lautsprechern PowerPack-Speicherkondensator serienmäßig Abmessungen: 50,8 mm x 25.4 mm x 14 mm Schnittstelle Stiftleiste mit Adapter Click the image for a bigger view. Instruction manual Art.No. Delivery 58325 LokSound 5 L DCC "blank decoder", Pinheader with adapter, gauge: 0 Only available at ESU LLC! 58315 LokSound 5 L DCC/MM/SX/M4 "blank decoder", Pinheader with adapter, gauge: 0
On order, shipped within 4-5 days