Electronics
With a 10 V light bulb. For use in the 8950 lighting base, the 8939 signal (old version) and 8940, the 8992 level crossing, in all locomotives that can be lighted and in models of ICE intermediate cars (exception: lighting with maintenance-free LEDs).
On order, shipped within 10-15 days
The DiMAX radio conversion set 2.4GHz consists of the 8131001 DiMAX radio receiver 2.4GHz and the 8131901 DiMAX radio transmitter 2.4GHz. This allows for an affordable entry into the new radio system. The operating instructions can be found on the relevant product page.
On order, lead time to be confirmed
The new DiMAX radio receiver operates on the 2.4GHz frequency internationally and can therefore be used worldwide. It supports up to 4 radio users and can be used with both Central stations with Massoth bus (DiMAX 800Z, 1200Z, 1210Z, LGB 55006 and PIKO 35010) and analogue controllers (LGB 51070, 51079 or PIKO 35002). The range is up to 100 metres in the open air. For the first time, the classic whip antenna is no longer required, as it is internally mounted.
On order, lead time to be confirmed
This retrofit wireless transmitter can equip all navigators currently on the market with the latest 2.4GHz radio technology. This ensures that the hand controller remains up to date in the future. The 2.4GHz wireless transmitter requires at least Navigator firmware version 2.2.
On order, lead time to be confirmed
In addition to the DiMAX EU radio transmitter (8133301), the circuit board including the antenna (without housing) is now also available as a spare part for the corresponding DiMAX EU radio receiver II (8133101). This makes it easy for customers to continue operating and maintaining existing DiMAX digital layouts with the old radio system, even after many years.
On order, lead time to be confirmed
The DiMAX radio transmitter has an extended range (up to 100 m) and can be retrofitted in the Navigator. A small hole through the housing wall is required.
On order, lead time to be confirmed
Since 2019, the DiMAX Navigator has been supplied with 2.4GHz radio technology. The 2.4GHz radio system allows international use and reduces the product range to a single transmitter. The range is comparable to the previous radio system. The DiMAX Navigators 8134801 are already equipped from the factory with a 2.4GHz radio chip onboard; a radio interface is no longer present. All Navigators currently on the market can be equipped with the retrofit transmitter 8131901. This ensures that the Navigators remain up to date technically in the future.
On order, lead time to be confirmed
Enjoy boundless freedom with the DiMAX Navigator. This handheld controller offers a range of functions that goes far beyond the operating options of handheld controllers to date. One highlight is that, for example, locomotives can be driven and points switched at the same time. For maximum operating enjoyment, the housing has been optimally shaped on ergonomic principles and the centre of gravity balanced so that it sits perfectly in the hand. Thanks to the symmetrical cross-section of the housing, the DiMAX Navigator is equally well suited to left-handed and right-handed users and can be operated optimally. A large, clearly arranged graphic display with backlighting provides comprehensive information on the locomotive currently being controlled, in a freely selectable language. This handheld controller is also equipped with switchable and dimmable blue/white keyboard lighting, which ensures running around the clock. The rotary knob is lit in different colours depending on the function. All locomotives from volume manufacturers available on the market can be shown on the LCD with the matching symbol and an individual name. The individual functions, the light symbol and the current speed step are also shown on the display. Since 2019 the DiMAX Navigator has been supplied with 2.4GHz radio technology. The 2.4GHz radio system allows international use and reduces the product range to a single transmitter. The range is comparable to that of the previous radio system. The DiMAX Navigators 8134801 are already fitted at the factory with a 2.4GHz radio chip on board, and a radio interface is no longer present. All Navigators previously on the market can be fitted with the retrofit transmitter 8131901. The Navigators will therefore remain technically up to date in future too. Features simple to use, ergonomically shaped large, easily legible graphic display adjustable backlighting easy to read in sunlight suitable for left-handed and right-handed users more than 10 language packs available to download manual in German and English easy for children to use (incl. child lock) illuminated rotary knob with status detection individual locomotive name per address 2 operating modes for the rotary knob for NMRA/DCC and Motorola operation 14/28/128 speed steps 99 functions per locomotive (F0 to F28 + 60 BS) parallel and serial function data up to 240 locomotive images (narrow gauge and standard gauge) control of 2 locomotives at the same time 2 STOP buttons (programmable STOP commands) radio and cable operation possible (depending on the system) various programming modes display of system power and system load point switching commands (with history) up to 32 routes programmable suitable for the following bus systems*: DiMAX (Massoth), XpressNet V 3.6, LocoNet
On order, lead time to be confirmed
The popular DiMAX Navigator is now available in a bright orange colour variant! It is the central hand controller for your model railway – for driving, switching and programming. With an open radio interface for 2.4 GHz or 433 MHz, plug-and-play retrofitting and full functionality even without a radio module. Stylish, flexible, future-proof – your Navigator, now in orange!
On order, lead time to be confirmed
A small, powerful switched-mode power supply, ready-made for connection to the DiMAX PC module or a small Central Station.
On order, lead time to be confirmed
The DiMAX 24 V | 12.5 A switched-mode power supply is the ideal power feed, precisely matched to the DiMAX product range (e.g. Digital Central Station 1210Z or Digital Booster 1202B). It is also suitable for other applications requiring consistently high power.
On order, lead time to be confirmed
The DiMAX switched-mode power supply 24V | 12.5A is the ideal power supply, precisely matched to the DiMAX product range (e.g. Digital Central Station 1210Z or Digital Booster 1202B). It is also suitable for other applications where a consistently high output is required.
On order, lead time to be confirmed
Facelift version 2021 of the popular 12 ampere garden railway command station with a new power output stage, optimised for operation with the DiMAX 1200T switched-mode power supply, achieving minimal power losses under full and partial load. Adjustable output voltage 14-22 volts; track current 4, 7 or 12 amperes. USB interface for PC control and automation, as well as firmware update for the command station and connected bus components. Supports locomotive addresses up to 10239, 14,28,128 speed steps, parallel and serial functions, F0 to F28 and 99 Binary State functions, automatic functions, etc.
On order, lead time to be confirmed
The DiMAX 1202B digital booster is a modern and powerful digital booster. With two separate output stages of 6 amps running current each, it offers ample reserves for 2 additional track sections on the model railway layout. If the 6 amps per track section are not sufficient, the two output stages can be connected together on the output side to form one output stage of 12 amps. The track voltage can be set in 5 steps: 14, 16, 18, 20 and 22 volts. A switched-mode power supply of 18-24 volts (DC) with sufficient power (min. 12A) is required for the power supply, for example the DiMAX 1200T switched-mode power supply (8135501) with up to 15 amps peak power. All desired settings are made with easy-to-use buttons on the front of the booster. A clear LED display shows the current settings and the operating state. With its different connection options, the booster can be used with most digital systems: booster bus socket for connection to Massoth / DiMAX digital command stations booster bus socket for connection to LGB MZS II and III digital command stations C-D-E terminal (e.g. for Lenz, Tams, Roco, etc.) Please observe the separate CDE usage note! Märklin CAN* (for operation on Märklin CS 2 / CS 3) is fully integrated from production year 2019 (new in 2019) direct track signal tap via terminals C, D for all digital command stations that do not provide a usable booster bus It can be used regardless of the data format and can therefore be operated, in addition to NMRA/DCC, with Motorola, Selectrix, etc., for example. The booster supports the following operating modes: normal running/booster mode braking booster function with active pass-through of function commands RailCom Märklin CAN / MfX* The booster can be operated on the Märklin CS II / III Central Station as a running booster. The matching connection cable 8312086 DiMAX Booster CAN bus cable for Märklin CS is not included in the delivery. MfX feedback is not available at present and is to be retrofitted at a later date with an additional module.
On order, lead time to be confirmed
Connect up to 5 additional bus components to your Central Station. Compatible with MZS. A control light indicates operational readiness.
On order, lead time to be confirmed
Powerful 3 amp locomotive decoder with a total load rating of four amps and 8 function outputs, suitable for locomotives with up to two motors. The eMOTION XL locomotive decoder is a high-quality decoder for large-scale and garden railways, for NMRA DCC and all generations of the LGB® MZS. With its various connection options and adjustable special functions, it can drive, among other things, speed-dependent sound module controls or uncoupling drives of the most varied technical designs. Simple function mapping, a freely programmable shunting speed and modern load control for digital and analogue operation (patent pending) round off the range of functions. Of course, analogue or digital operation is recognised automatically. The eMOTION XL locomotive decoder also supports automatic detection between serial (LGB® MZS) and parallel (NMRA DCC) function data processing. The features of the eMOTION XL locomotive decoder at a glance: 14, 28 and 128 speed steps 256 internal speed steps 10239 locomotive addresses programmable speed curve starting, medium and maximum speed (as well as delay times) serial and parallel control for all light and function outputs incl. LGB® P sound updates digital and analogue operation with automatic detection compatible with NMRA DCC and LGB® MZS (all generations) latest-generation load control (for digital and analogue operation) adjustable motor frequency (70Hz – 16 kHz) 3 light connections (front, rear, interior) max. 0.3A each 6 function outputs (all with configurable special functions) max. 0.6A each light and function outputs dimmable and can be activated in analogue mode programmable flashing light, short-time and clock generator functions 2 additional contact inputs for future functions (reserved) shunting speed (with free function mapping) simple function mapping for all function outputs all function outputs freely addressable (F1 to F16) total load rating of 4 amps (motor output stage and function outputs) motor output stage rated for 3 amps (suitable for up to 2 motors of 1.5 amps each) voltage buffer connection integrated for smooth running (accessory: 8151001 or 8151501) overload and temperature protection for the motor and function outputs reset function for all CV values software can be updated CV reading CV writing bitwise CV writing indirect CVs (via register programming for older digital systems) direct register programming (CV 1 – CV4) POM – Program on Main (programming on the main track)
On order, lead time to be confirmed
The Powercap 200 (ex. nano), with its miniature design, is suitable for particularly small, single-motor models, including field railway locomotives, and buffers for a few seconds – enough to get a small locomotive over a dirty section of track. With its minimal size of just 25 x 17 x 15 mm, it can be fitted almost anywhere. The three-core connecting cable (200 mm) can be shortened individually.
On order, lead time to be confirmed
Following the introduction of the Powercap 200, the more powerful Powercap 900 now complements the product range. Despite its compact dimensions of just 30x30x16mm, it is capable of buffering a single-motor locomotive drawing 600mA for up to 6 seconds, and for a considerably longer period when the current consumption is lower. It replaces item 8151601 Powercap micro. Available from October 2024.
On order, lead time to be confirmed
Following the introduction of the Powercap 200 and Powercap 900, the more powerful Powercap 2300 completes the product range. Despite its compact dimensions of just 44x23x32mm, it is able to buffer a two-motor locomotive with 2000mA for up to 12 seconds, and considerably longer with lower current consumption. It replaces 8151701 Powercap maxi. Available from April 2025.
On order, lead time to be confirmed
24.03.2025 – 8151701 is replaced by 8151321 Powercap 2300 The new Powercap maxi replaces the Goldcap buffer 8151501. The size has been reduced by about 40 %. Reserve of up to 30 seconds! The eMOTION Powercap maxi bridges brief interruptions in the track voltage. It was designed especially for twin-motor locomotives. The motor and the special functions are supplied from the storage unit during this interruption. Locomotives can therefore cross common crossings or insulated sections without stopping. The buffering time is up to 30 seconds, depending on the connected load, the current speed and the charge level of the storage unit. Universal digital use & intelligent technology Thanks to its well-thought-out design and the use of special capacitors, the Powercap maxi, with integrated charging circuit and charging function cut-out during decoder programming, is suitable for use with almost all digital decoders that provide the Decoder + and Decoder – contacts directly. (tested with: Massoth, LGB®, Lenz©, Zimo©) Direct connection of the Powercap maxi to decoders of the eMOTION series The Powercap maxi is particularly suitable for connection to decoders of the eMOTION series. The Decoder + (red) and Decoder – (black) contacts are used as usual. The third wire (white) is used to switch off the charging function when the contact is open. This function is handled by a function output of the eMOTION decoder. When the decoder is being programmed or read, the charging function is switched off automatically. The programming procedure can therefore be carried out without any problem. With third-party or older decoders, the switch also included in the delivery is used. The performance data are: Buffering time up to 30 seconds (depending on load) maximum buffer current 3A maximum charging current 400mA Operating voltage 6-20 V DC (max. 24 V)
On order, lead time to be confirmed
The new 10FX servo decoder is an innovative further development of the long-proven and versatile 8FS/8FX decoder generation. It provides sufficient power reserves for controlling up to four servos, two uncouplers or pantograph drives, and other consumers with a wide range of functions, thanks to its ten function outputs suitable for analogue operation, which have a total current capacity of two amperes. Additionally, a voltage buffer is integrated, ensuring smoother operation of the connected servos and uncouplers. With these performance specifications, there is nothing left to desire.
On order, lead time to be confirmed
Compact and powerful DCC function decoder with four reinforced function outputs, each capable of handling a peak load of 1 ampere. The total current capacity is also 1 ampere. The solder connections are located on the underside of the small 25 x 16 mm circuit board. A removable mounting bracket is included. The pack contains two pieces. Available from October 2024.
On order, lead time to be confirmed
Completely newly developed and even more powerful is the new XXL II locomotive decoder, suitable for locomotives with up to 4 motors, with up to 8 amperes of running current and 10 amperes of total current. Highlights: New function mapping, F0-F127, 10 function outputs, 2 servo connections, bus connection for MASSOTH/LGB and SUSI, overload and temperature protection for motor and function outputs. Updatable.
On order, lead time to be confirmed
Universal 1.8 amp locomotive decoder with 8 function outputs, suitable for locomotives with 1 motor. The eMOTION L decoder is a compact locomotive and function decoder, optimally designed for the demands of large-scale operation. In addition to the motor output for single-motor locomotives, it offers up to 8 programmable function outputs. The eMOTION L decoder offers excellent digital and analogue running characteristics. Its good analogue capability is also worth stressing, allowing stable operation from about 7 to 8 volts. With an additional voltage buffer it can do its job even more reliably in analogue and digital operation, and thereby avoids dropouts caused by dirty spots on the track. The features of the eMOTION L locomotive decoder at a glance: locomotive decoder for digital and analogue operation 14, 28 and 128 speed steps motor output rated for 1.8A connection for a model-making servo bus interface for MASSOTH and LGB® modules programmable speed curve starting, medium and maximum speed (as well as delay times) adjustable serial and parallel control for all light and function outputs control of parallel data updates (LGB®) digital and analogue operation with automatic detection compatible with NMRA DCC and LGB® MZS (all generations) latest-generation load control (for digital and analogue operation) adjustable motor frequency (90Hz – 23.5 kHz) 2 light connections (front, rear) max. 0.5A each 6 function outputs (2 of 0.5A each, 4 of 50mA each) light and function outputs dimmable and can be activated in analogue mode programmable flashing light and short-time functions shunting speed and delay times can be switched by function key simple function mapping with direction assignment all function outputs freely addressable (F1 to F16) voltage buffer connection integrated for smooth running (accessory: 8151001 or 8151501) overload and temperature protection for the motor and function outputs reset function for all CV values CV reading CV writing bitwise CV writing indirect CVs (via register programming for older digital systems) direct register programming (CV 1 – CV4) POM – Program on Main (programming on the main track)
On order, lead time to be confirmed