Electronic Accessories
Roads and control technique in the advantageous set. This set allows to build a 2-lane H0 oval using Laser Street elements inclusive of a functioning bus stop. Along with a control unit suitable for a bus stop (16 V alternating current) there are the required Laser Street elements (H0), 1 Stop section, 1 Branch-off junction, 2 Sensors, 1 additional magnet (H0), 5 m of Special contact wire as well as detailed instructions within the set.
On order, shipped within 4-5 days
Two traffic lights with LED signals in the colours green, yellow and red with a control box. Equally suitable for Car System, Car System Digital or independent operation. The most current international signal sequences can be triggered via the inputs of the box: one regulator each for country setting and duration. Possible signal lights: -green/yellow/red -green/yellow/red/red-yellow -green/green blinking/yellow/red/red-yellow.
On order, shipped within 4-5 days
Two traffic lights with LED signals in the colours green, yellow and red. Equally suitable for Car System and Car System Digital. By connecting them to the control unit »Traffic Light Control« art. 161654 they help represent the international signal sequence with three states (green/yellow/red). By connecting them to an »Extension module« art. 161352 they help represent the international signal sequences with three states (green/yellow/red), four states (green/yellow/red/yellow-red) or five states (green/green blinking/yellow/red/red-yellow).
On order, shipped within 4-5 days
Printed circuit board allowing to retrofit various analog Car System vehicle models for digital operation with ultrasonic locating, fully automatic distance control and modifications of the driving speed while playing. Moreover all soldering pads required for additional lighting and equipment with sound functions are provided on the board. Experienced modellers will thus be able to convert any analog Car System vehicle to an integrally Car System Digital model.
On order, shipped within 4-5 days
Make the stationary vehicle model of your choice fit for Car System. Chassis kit to motorize stationary models of buses and trucks for Car System operation. Set contains all vehicle components required for the assembly of a fully functioning two-axle Car System H0 chassis (bus and truck), except the rechargeable batteries: support PCB, motor with worm, motor holder with worm wheel and driving axle, driving wheels, front axle with wheels, steering rod with magnet, front axle holder, switch, charging socket, dry-reed sensor, resistors to adjust the charging current and driving speed. Conversion info: - Axle base can be selected continuously between 38 mm and 88 mm - Width: 29 mm - Support PCB with all electrical connections required for easy soldering of components, incl. soldering pads for warning beacons - Fastening of motor and gear unit at choice horizontal (e.g. in buses and trucks with dropped frame) or vertical (e.g. in semitrailer trucks) - Built-in HERPA standard crossmember can be removed when using any bodywork of other manufacturers
On order, shipped within 4-5 days
Make the stationary vehicle model of your choice fit for Car System. Chassis kit to motorize stationary models of N buses and N trucks for Car System operation. Set contains all vehicle components required for the assembly of a fully functioning two- or three-axle Car System N gauge chassis (bus and truck), except the rechargeable batteries: Motor with worm, Motor holder with worm wheel and driving axle, Driving wheels, Front axle with wheels, Steering rod with magnet, Front axle holder, Switch, Charging socket, Dry-reed sensor, Resistors to adjust the charging current. Conversion info: - Fastening of motor in gear unit at choice horizontal (e.g. in buses and trucks with dropped frame) or vertical (e.g. in semitrailer trucks) - Axle bases (horizontal motor) can be selected continuously between 25 mm and 43 mm - Axle bases (vertical motor) can be selected continuously between 20 mm and 40 mm - Width: approx. 16 mm
On order, lead time to be confirmed
5 SMD reflector LEDs with powerful directional luminosity that like head lights does not radiate towards the interior of the vehicle. Suitable e.g. for the lighting of funfair kits, the equipment of vehicles with lights and many others more. SMD LEDs are characterized by their weak generation of heat and long service life. PAS format: 0603, corresponds to 1.6 x 0.8 mm. Operate LEDs only with the stated low voltage.
On order, shipped within 4-5 days
5 SMD reflector LEDs with powerful directional luminosity that like head lights does not radiate towards the interior of the vehicle. Suitable e.g. for the lighting of funfair kits, the equipment of vehicles with lights and many others more. SMD LEDs are characterized by their weak generation of heat and long service life. PAS format: 0603, corresponds to 1.6 x 0.8 mm. Operate LEDs only with the stated low voltage.
On order, shipped within 4-5 days
5 SMD reflector LEDs with powerful directional luminosity that like head lights does not radiate towards the interior of the vehicle. Suitable e.g. for the lighting of funfair kits, the equipment of vehicles with lights and many others more. SMD LEDs are characterized by their weak generation of heat and long service life. PAS format: 0603, corresponds to 1.6 x 0.8 mm. Operate LEDs only with the stated low voltage.
On order, shipped within 4-5 days
5 SMD reflector LEDs with powerful directional luminosity that like head lights does not radiate towards the interior of the vehicle. Suitable e.g. for the lighting of funfair kits, the equipment of vehicles with lights and many others more. SMD LEDs are characterized by their weak generation of heat and long service life. PAS format: 0603, corresponds to 1.6 x 0.8 mm. Operate LEDs only with the stated low voltage.
On order, shipped within 4-5 days
Light functions for your Car System Digital vehicles. The lighting kit contains two PCBs provided with LEDs that ensure all the lights on lorry models »MB SK« or »MAN F2000«. The adapted positions of the fastening holes and LEDs allow direct fastening of the PCBs to the bumpers of the vehicles. The LED lighting kit contains: - Front board with headlights and turn signal lamps - Rear board with rear lights and turn signal lamps - Set of cables To convert conventional Car System model vehicles for Car System Digital operation simply use the »Analog-Digital Conversion kit«, Art. 163701.
On order, shipped within 4-5 days
Rotating beacon modules (RKL modules) / flashing lights are intended to operate on 0.8 to 3.3 V DC, and can be used for both, Car System vehicles and the equipment of stationary models. Modules are 3.5 mm wide and 2.4 mm high including PCB.
On order, lead time to be confirmed
Rotating beacon modules (RKL modules) / flashing lights are intended to operate on 0.8 to 3.3 V DC, and can be used for both, Car System vehicles and the equipment of stationary models. Modules are 3.5 mm wide and 2.4 mm high including PCB.
On order, shipped within 4-5 days
Rotating beacon modules (RKL modules) / flashing lights are intended to operate on 0.8 to 3.3 V DC, and can be used for both, Car System vehicles and the equipment of stationary models. Modules are 3.5 mm wide and 2.4 mm high including PCB.
On order, shipped within 4-5 days
Rotating beacon modules (RKL modules) / flashing lights are intended to operate on 0.8 to 3.3 V DC, and can be used for both, Car System vehicles and the equipment of stationary models. Modules are 3.5 mm wide and 2.4 mm high including PCB.
On order, shipped within 4-5 days
Rotating beacon modules (RKL modules) / flashing lights are intended to operate on 0.8 to 3.3 V DC, and can be used for both, Car System vehicles and the equipment of stationary models. Modules are 3.5 mm wide and 2.4 mm high including PCB.
On order, shipped within 4-5 days
The refill bottle contains specially formulated smoke fluid for use in our smoke generator (Art. 180729). Simply top up and create fantastic smoke effects! The contents are sufficient for approx. 10 hours of smoke.
Pre-order, release expected in November 2026
Modern and widely used suitcase light. Particularly suitable for designing city, street and industrial scenes. The mast is made of metal. The intricate one-light lamp is equipped with long-life LED technology. The product is ready for connection to 12 V direct current (DC). Use the »Transformer«, Art. 180699, to operate the lamp. Height: 94 mm. Light colour: cold white. Contents: 3 units.
On order, shipped within 4-5 days
Modern and widely used suitcase light. Particularly suitable for designing city, street and industrial scenes. The mast is made of metal. The intricate one-light lamp is equipped with long-life LED technology. The product is ready for connection to 12 V direct current (DC). Use the »Transformer«, Art. 180699, to operate the lamp. Height: 94 mm. Light colour: cold white. Contents: 3 units.
On order, shipped within 4-5 days
Modern and widely used neon light. Particularly suitable for designing city, street and industrial scenes. The mast is made of metal. The intricate one-light lamp is equipped with long-life LED technology. The product is ready for connection to 12 V direct current (DC). Use the »Transformer«, Art. 180699, to operate the lamp. Height: 95 mm. Light colour: cold white. Contents: 3 units.
On order, shipped within 4-5 days
Model of a historical path light. The filigree design of this lamp has a special charm. This makes it particularly suitable for illuminating old town…
On order, shipped within 4-5 days
Model of a modern path light. The filigree design of this lamp has a special charm. This makes it particularly suitable for illuminating paths, parks…
On order, shipped within 4-5 days
Create atmosphere with timeless design. Set of 3 wall lights in a detailed design, single-flame. The lamp is easy to install on buildings or walls and set the scene. Particularly suitable for atmospheric lighting in cities and parks. The model is made of filigree plastic and equipped with long-lasting LED technology. Colour: black. Height: 15 mm. Light colour: warm white. Ready for connection for 12 V, direct voltage (DC). Use the FALLER transformer 50 VA 50-60Hz, Art. 180699, for operation.
On order, shipped within 4-5 days
Modern and widely used suitcase light. Particularly suitable for designing city, street and industrial scenes. The mast is made of metal. The intricate one-light lamp is equipped with long-life LED technology. The product is ready for connection to 12 V direct current (DC). Use the »Transformer«, Art. 180699, to operate the lamp. Height: 94 mm. Light colour: cold white.
On order, shipped within 4-5 days