Electronic Accessories
The LA 010 adapter is required when connecting motorised point motors or EPL drives to the LS100/LS101 signal receiver. Dimensions: 14 x 30 x 13 mm
On order, lead time to be confirmed
The LS101 function decoder, the successor to the well-known LS100, can connect four points, signals, etc. DC voltage is present at the outputs. This must be taken into account when using LEDs. The connection to the central unit required for the feedback of the point position is established via terminals R and S of the LS101; the point or signal position is then displayed, for example, on the hand controller or passed on as information to a control program.
On order, lead time to be confirmed
Up to six points, signals or other accessories can be controlled via the LS150 function decoder. It is supplied with separate AC voltage; the TR100 transformer is recommended for this purpose. This provides AC voltage at the switching outputs. This voltage form is of great advantage when using so-called "dual-coil point motors". Dimensions: 120 x 60 x 20 mm
On order, lead time to be confirmed
Up to 8 inputs of the LR101 can be connected to switching contacts or LB101 occupancy detectors, and a further input to the LB050 voltage detector. To bridge uncertain switching states (e.g. brief interruptions in the current flow), a programmable delay time for the free indication can be assigned to each occupancy detector input on the LR101.
On order, lead time to be confirmed
To detect track occupancy in conjunction with the LR101, the LB101 operates as a current sensor and is connected between the LR101 and the track section to be monitored. One LB101 can monitor two track sections independently. Dimensions: 60 x 12 x 42 mm
On order, lead time to be confirmed
The LK200 operates on the residual current principle, with polarity reversal occurring at a residual current of just 100 mA, and polarity indication provided by an LED. Switching is electronic without relays, ensuring high switching speed and no mechanical wear. Wiring is straightforward, allowing the LK200 to be retrofitted into the layout with minimal effort. No adjustment or setting work is required. The maximum current rating is 5 amperes.
On order, lead time to be confirmed
This 4-digit display can show the locomotive's address in the monitored section of track. It can be installed anywhere on the model railway layout, for example in a panel control desk. Dimensions: 47.5 x 65 x 12 mm
On order, lead time to be confirmed
Controller for four locomotives, 10 locomotive functions and 10 points/signals
On order, lead time to be confirmed
The LV103 is designed to meet the safety requirements and conditions for operating a model railway. If required, the track voltage and output current can be individually adjusted to suit the specific situation, with a maximum output current of 5 amperes. The factory settings are an output voltage of 16V and a maximum current of 5A.
On order, lead time to be confirmed
In the simplest case, the track voltage to the braking section before the signal is routed via the BM1. When the signal shows "Hp 0", the BM1 creates an asymmetry in the otherwise symmetrical digital voltage, which is detected by decoders from the GOLD and SILVER series. The result is a gentle deceleration of the train until it comes to a standstill. If the train approaches from the opposite direction, it simply continues running, as the asymmetry is detected depending on the direction of travel.
On order, lead time to be confirmed
The BM2 not only allows the train to be stopped at "Hp 0" before the signal, but also offers the installation of a slow-running section for "Hp 2". The track section before the signal is divided into a running section and a braking section. The length of the running section must be designed so that the longest train operating there fits completely within it. The length of the braking section is determined (as with the BM1) by the set braking deceleration or the set braking distance.
On order, lead time to be confirmed
The Block Section Module BM3 is a building block that uses ABC technology to slow down and stop trains. It enables prototypical block section operation. The number of blocks is unlimited, as one BM3 is used for each block. The BM3 has a connection for colour light signals to indicate the status: red signal = next block occupied, BM3 set to stop; green signal = next block free, BM3 set to proceed.
On order, lead time to be confirmed
A block section equipped with BM3 that runs through a reversing loop requires, in addition to the LK200, a special BM3 module, the BM3K, and two of them. The reason is the reporting line, which consists of only one wire, which is very practical in the "normal case". In this special case, however, the potential is reversed by the reversing loop module, so the reporting via the reporting line would no longer work.
On order, lead time to be confirmed
The BMA adapter (adapter for the BM3 block section module) enables the connection of signals equipped with a double-coil or motor drive to the BM3 block section module. Technically, the BMA is a relay controlled by the lamp outputs of the BM3. Dimensions: 33 x 19 x 12 mm
On order, lead time to be confirmed
The Digital plus interface provides an Ethernet connection in addition to the USB interface. This allows the system to be connected to a PC or a router, opening up interesting new possibilities for model railway control. Dimensions: 120 x 60 x 20 mm
On order, lead time to be confirmed
Up to 16 digitally controlled solenoid accessories can be switched with the LW150. Two buttons or a single-pole changeover switch are required for each point/signal (not included in the LW150 supply). Multiple button modules can be used simultaneously, each button module has its own adjustable XpressNet address. Dimensions: 120 x 60 x 20 mm
On order, lead time to be confirmed
The SET101 consists of the LZV200 central power booster and the LH101 hand controller. You can control locomotives with digital addresses from 1 to 9999, plus one conventional locomotive. To control speed, the LH101 hand controller features a finely graduated, precise rotary control. Up to 68 functions in locomotives can be switched – either momentarily or continuously. Double and multiple traction are easily configured.
On order, lead time to be confirmed
The SET101-R consists of the LZV200 central power booster and the LH101-R wireless hand controller. You can control locomotives with digital addresses from 1 to 9999, plus one conventional locomotive. The hand controller features a finely graduated, precise rotary knob for speed control. Up to 68 functions in locomotives can be switched – either momentarily or continuously. Double and multiple traction are easily configured.
On order, lead time to be confirmed
Starter Digital Set, consisting of the Starter Central Station, Starter Hand Controller and switched-mode power supply. With the Starter Digital you can control up to 4 locomotives independently of each other, activate up to 10 functions in locomotives and digitally switch up to 10 points (or signals). 2 Starter Hand Controllers can be used in parallel. The switched-mode power supply has a typical output current of 4A, guaranteed 3A.
On order, lead time to be confirmed
The extension set consists of a 20-core connecting cable, 32 yellow LEDs, one red LED, and one green LED.
On order, lead time to be confirmed
With the automatic shuttle unit, you can have a train shuttle back and forth between two stations. An electronic circuit stops the train at the station and then lets it run back again. Easy to install, with an adjustable dwell time and prototypical gentle starting and braking. For connection to 10-24 V DC. The 10345 is the technically optimised and improved successor to the 10340.
On order, shipped within 10-15 days
With this small contact, you can automatically control your LGB points, signals and other accessories. It is triggered by a locomotive equipped with the LGB 17010 magnet and can easily be clipped into most LGB tracks.
On order, shipped within 10-15 days
With this versatile control panel you can switch up to four electrical circuits on and off, e.g. electrically separated track blocks or street lamps. Each toggle switch operates one circuit. Depending on your needs, you can connect the control panel to DC or AC power by means of the plugs on the sides. An LED indicates when the control panel is being supplied with power. Colour-coded connections on the back make hooking it up easier. With stickers for marking the switch assignments. 126 x 116 x 66 mm. Replaces item 51800.
On order, shipped within 10-15 days
Reversing loop module for the digital LGB system world. Switch the reversing loop on your digital layout automatically and without short circuits. In doing so, you protect your digital system and of course your rolling stock. An additional advantage of the reversing loop module: several reversing loops can be used on the layout at the same time. Conventional reversing loop modules generate a short circuit when the train enters and, by means of a voltage dip, force the polarity of the track to be reversed, e.g. the 55080. The MZS reversing loop module, by contrast, switches without short circuits; an interruption of the voltage on the track is prevented. Overloading of the MZS central unit by the deliberately generated short circuit is thus a thing of the past. Above all, this protects track components such as locomotive decoders, point decoders and the electronics usually installed in locomotives and wagons. Compatible with the previous components. Notes: Suitable to a limited extent for analogue operation. This product is not weatherproof and must be protected from moisture. 80 x 70 x 20 mm.
On order, shipped within 10-15 days