Electronic Accessories
Connect up to 5 additional bus components to your Central Station. Compatible with MZS. A control light indicates operational readiness.
On order, lead time to be confirmed
Universal 4-function function decoder A universal 4-function function decoder for controlling and switching standard motor and point motors: regular coil point motors (2- and 3-wire) with pulse switching or genuine motor point motors. Four protected contact inputs allow switching via manual contacts, e.g. from a control panel or signal box or track contact, alternatively up to 8 light functions. The settings are made via CV programming (as well as POM).
On order, lead time to be confirmed
Universal switching decoder for points, motors and switching tasks The Massoth 4K III switching decoder is a versatile universal decoder for the digital control of points, motor drives and numerous other switching functions on your model railway layout. Four independent switching outputs allow the direct connection of up to four point motors or eight freely usable switching outputs. In addition to classic garden railway point motors, the switching decoder also supports twin-coil drives and motorised point drives. The powerful output stages also allow motors, lamps or other loads to be switched reliably. A particular highlight is the eight integrated contact inputs. They allow switching operations to be triggered not only digitally but also directly via push buttons, track contacts or reed contacts. Points and other functions can thus be switched fully automatically or manually. Alternatively, these connections can be used as status LED outputs. The switching decoder can be operated using both point addresses and locomotive addresses. In locomotive mode, extensive functions are available, such as freely assignable function keys, flashing functions, short-time functions (monoflop), PWM output voltage and automatic switch-back functions. The decoder is therefore also excellently suited to lighting, signalling and automation tasks. For particularly convenient commissioning, the 4K III switching decoder has an integrated programming load. All CVs can therefore be read and written directly without having to connect an additional load. CV reading, CV writing, bitwise programming and Programming on Main (PoM) are supported. Of course, the decoder's firmware can be updated, bringing it up to date at any time. Highlights Digital universal switching decoder for DCC layouts Four switching channels for up to four point or motor drives Eight freely usable switching outputs Eight programmable contact inputs for push buttons, reed contacts or track contacts Contact inputs can alternatively be used as status LED outputs Suitable for single-coil and twin-coil drives Also suitable for switching motors, lamps and other loads Operation via point or locomotive addresses Freely programmable function assignment in locomotive mode Flashing, monoflop and automatic functions Adjustable PWM output voltage Automatic switch-back function Integrated programming load for convenient CV reading and writing Programming via CV and PoM Firmware update via the Massoth Service Tool (MST) Overload protection on all outputs Made in Germany
On order, lead time to be confirmed
A completely newly developed function decoder with an expanded range of functions and, for the first time, a service-friendly plug-in connecting cable. In addition to the powerful switching output, the function decoder also features additional contact inputs.
On order, lead time to be confirmed
The DiMAX LED control module provides 16 function outputs for driving LEDs for various pre-programmed light effects (e.g. house lighting, traffic lights, flashing indicators, construction site beacons) and various signal aspects (DB, DR, Switzerland) with four signal aspects each, and can be operated digitally and analogously*.
On order, lead time to be confirmed
Switch the reversing loop on your layout to prevent short circuits, thereby protecting your digital system and rolling stock. Only with this technology can multiple reversing loops be operated simultaneously! Switching currents up to 15 amperes (peak current). With soft-start function when the train is standing at the isolation point. Regular short-circuit operating mode is of course also supported. In addition, the reversing loop module can be used in analogue operation!
On order, lead time to be confirmed
The DiMAX FB feedback module is used to detect events on the model railway layout, such as reporting a train on a specific track or the feedback from a switched point. The module monitors 16 contact inputs (compared to the previous 8 in 8170001). When a change occurs at an input, a command is sent to the central station via the DiMAX FB feedback bus. Depending on the module’s programming, this can trigger various actions. Either a point is switched directly, an automatic function in the DiMAX central station is started, or the feedback is forwarded to a PC.
On order, lead time to be confirmed
A completely newly developed electronic track contact for the DiMAX digital system with a novel sensor. The classic EPL control system is not supported. The contents supplied include two track contacts.
On order, lead time to be confirmed
The DiMAX FB occupancy detection module 8170510 monitors four independent track sections. As soon as a train is on an occupancy detection section, it is reported as occupied. The continuous current is 6A (peak current 8A). The trigger current for occupancy detection is between 2mA and 100mA and is individually adjustable in five stages. The occupancy detection module is suitable for both booster and reversing loop operation. Detailed connection diagrams are in the bilingual manual supplied with the product.
On order, lead time to be confirmed
With "intermittent train control" (PZB), the modern "full-size" railway today controls its operating processes to monitor and influence rail-bound vehicles by transmitting position-related data from the track to the train. In currently common systems, for example, it is monitored, among other things, that a signal showing "stop" has not been passed. Massoth has adopted precisely this proven principle with the innovative DiMAX-PZB/IR control system for the garden railway sector, and with just three components (prerequisite: SUSI-BIDI capability of the locomotive decoder) transmits data relevant to orderly operation from the track to the locomotives by infrared command. This does not merely execute train-controlled functions on the layout; genuine position-related commands are transmitted to the train. Enjoy the automatic stop of the train in front of a red signal and the continuation of the journey at the "clear" signal aspect, function commands for groups of trains, automatic triggering of sound, pulsed smoke generator and other decoder features, and many other functions. Complex wiring or isolating gaps in the track, as well as laying bus and feedback contact cables for PC control, are finally a thing of the past with DiMAX PZB. DiMAX PZB/IR offers the keen garden railway enthusiast many possibilities, for example: Switching signals and the associated train control Braking and stopping without braking section/modules Further functions are in preparation, such as: Locomotive position detection and feedback without track contact / feedback detector Triggering of sounds without track magnet or reed contact Feedback functions (e.g. Railcom© or MfX©) can be integrated in addition. The system components need no additional wiring; the power supply already present via the track is sufficient for operation. The permanent data transmission takes place independently of the digital track signal, by infrared signal from the signal decoder in the track to the vehicle fitted with a receiver as it passes over the transmitter. This can, for example, switch a function in the vehicle (light, steam, etc. on/off) or trigger an automatic action such as the bell ringing before a level crossing, but also a timed station stop. The data to be transmitted with PZB/IR can, however, also be influenced by a digital command on the track, if, for example, a signal aspect switched via the Navigator is transmitted to the vehicle in this way and the locomotive is thereby stopped in front of the signal showing "red". The PZB system components are supplied in sets with different compositions.
On order, lead time to be confirmed
The red lock-out prevents a train passing in the opposite direction from being stopped at a red signal. With "intermittent train control" (PZB), the modern "full-size" railway today controls its operating processes to monitor and influence rail-bound vehicles by transmitting position-related data from the track to the train. In currently common systems, for example, it is monitored, among other things, that a signal showing "stop" has not been passed. Massoth has adopted precisely this proven principle with the innovative DiMAX-PZB/IR control system for the garden railway sector, and with just three components (prerequisite: SUSI-BIDI capability of the locomotive decoder) transmits data relevant to orderly operation from the track to the locomotives by infrared command. This does not merely execute train-controlled functions on the layout; genuine position-related commands are transmitted to the train. Enjoy the automatic stop of the train in front of a red signal and the continuation of the journey at the "clear" signal aspect, function commands for groups of trains, automatic triggering of sound, pulsed smoke generator and other decoder features, and many other functions. Complex wiring or isolating gaps in the track, as well as laying bus and feedback contact cables for PC control, are finally a thing of the past with DiMAX PZB. DiMAX PZB/IR offers the keen garden railway enthusiast many possibilities, for example: Switching signals and the associated train control Braking and stopping without braking section/modules Further functions are in preparation, such as: Locomotive position detection and feedback without track contact / feedback detector Triggering of sounds without track magnet or reed contact Feedback functions (e.g. Railcom© or MfX©) can be integrated in addition. The system components need no additional wiring; the power supply already present via the track is sufficient for operation. The permanent data transmission takes place independently of the digital track signal, by infrared signal from the signal decoder in the track to the vehicle fitted with a receiver as it passes over the transmitter. This can, for example, switch a function in the vehicle (light, steam, etc. on/off) or trigger an automatic action such as the bell ringing before a level crossing, but also a timed station stop. The data to be transmitted with PZB/IR can, however, also be influenced by a digital command on the track, if, for example, a signal aspect switched via the Navigator is transmitted to the vehicle in this way and the locomotive is thereby stopped in front of the signal showing "red". The PZB system components are supplied in sets with different compositions.
On order, lead time to be confirmed
With "intermittent train control" (PZB), the modern "full-size" railway today controls its operating processes to monitor and influence rail-bound vehicles by transmitting position-related data from the track to the train. In currently common systems, for example, it is monitored, among other things, that a signal showing "stop" has not been passed. Massoth has adopted precisely this proven principle with the innovative DiMAX-PZB/IR control system for the garden railway sector, and with just three components (prerequisite: SUSI-BIDI capability of the locomotive decoder) transmits data relevant to orderly operation from the track to the locomotives by infrared command. This does not merely execute train-controlled functions on the layout; genuine position-related commands are transmitted to the train. Enjoy the automatic stop of the train in front of a red signal and the continuation of the journey at the "clear" signal aspect, function commands for groups of trains, automatic triggering of sound, pulsed smoke generator and other decoder features, and many other functions. Complex wiring or isolating gaps in the track, as well as laying bus and feedback contact cables for PC control, are finally a thing of the past with DiMAX PZB. DiMAX PZB/IR offers the keen garden railway enthusiast many possibilities, for example: Switching signals and the associated train control Braking and stopping without braking section/modules Further functions are in preparation, such as: Locomotive position detection and feedback without track contact / feedback detector Triggering of sounds without track magnet or reed contact Feedback functions (e.g. Railcom© or MfX©) can be integrated in addition. The system components need no additional wiring; the power supply already present via the track is sufficient for operation. The permanent data transmission takes place independently of the digital track signal, by infrared signal from the signal decoder in the track to the vehicle fitted with a receiver as it passes over the transmitter. This can, for example, switch a function in the vehicle (light, steam, etc. on/off) or trigger an automatic action such as the bell ringing before a level crossing, but also a timed station stop. The data to be transmitted with PZB/IR can, however, also be influenced by a digital command on the track, if, for example, a signal aspect switched via the Navigator is transmitted to the vehicle in this way and the locomotive is thereby stopped in front of the signal showing "red". The PZB system components are supplied in sets with different compositions.
On order, lead time to be confirmed
PZB/IR starter set with 2 x PZB/IR signal decoders and 1 x PZB/IR receiver.
On order, lead time to be confirmed
The new DiMAX PC Module III (8175230) replaces the proven 8175201 and features completely revised electronics with a new output stage for maximum operational reliability. Thanks to UltraFastUpdate, the integrated SUSI interface, and the robust DC socket, the module is more powerful and user-friendly than ever before. It connects your DiMAX Central Station to the PC, enabling programming, updates, diagnostics, and service functions via the Massoth Service Tool (MST) – and in the future via a new, enhanced PC software. Simply connect via USB 2.0 and get started!
On order, lead time to be confirmed
Do you own not just one or two digital locomotives? Do you like programming decoders to your own specifications? Are you a member of a Gauge G modelling railway club? Are you a model railway dealer offering the best service for your customers? Then the new Decoder Service Board is an important tool for you. The revised Decoder Service Board offers a wide range of interfaces for the digital modeller. This allows almost all garden railway decoders available on the market to be programmed and tested. Plug-in connections for speakers, uncouplers, servos and the SUSI bus, as well as screw terminals for the power connection and the motor, are of course included. LGB gearboxes, voltage buffers (3-pole) and many other components can be connected directly.
On order, lead time to be confirmed
The Massoth Service Stick includes the latest full version of the Massoth Service Tools, including all available sound projects, firmware files, and decoder profiles, as well as operating instructions and promotional material. The Massoth Service Tool is included as standard with the 8136501 DiMAX 1210Z Digital Central Station and the 8175201 DiMAX PC Module.
On order, lead time to be confirmed
The DiMAX FB bus distributor simplifies things: it is a multi-socket outlet for the Massoth DiMAX FB control bus. In comparison with the DiMAX control bus, the DiMAX feedback bus operates using shielded CAT network cables. The bus distributor provides four freely accessible DiMAX FB bus sockets (8-pin). Additionally, a classic (6-pin) DiMAX bus socket is located inside the housing. This allows the new DiMAX FB bus system to be connected to digital central units without a DiMAX FB bus. A separate power supply is not required.
On order, lead time to be confirmed
A suitable connecting cable for item 8442010 Shunting coupling 2.0 and the predecessor 8442000 Shunting coupling.
On order, lead time to be confirmed
Connecting cable for EVO-S point motor. Suitable for all EVO-S models manufactured from September 2023 (from serial number 3000).
On order, lead time to be confirmed
With the pantograph drives for single-arm and scissors-type pantographs, locomotives can be retrofitted with a sophisticated drive system. The drive is not limited to the well-known single-arm pantographs (8440013), such as those on the Ge 4/4 II and Ge 4/4 III. The new drive is designed so that scissors-type pantographs (84440023) can be operated for the first time. This makes retrofitting drives possible, for example, for the Crocodile (2040x) or the Schnüpftrückerli (2045x). And of course, old or defective drives can now be replaced. A special feature is the pleasantly slow and realistic speed when raising and lowering the pantographs. They are not opened and closed like a pocket knife. And thanks to the integrated spring mechanism, the pantograph can be raised or lowered manually without damaging the mechanism.
On order, lead time to be confirmed
With the pantograph drives for single-arm and scissors-type pantographs, locomotives can be retrofitted with a sophisticated drive system. The drive is not limited to the well-known single-arm pantographs (8440013), such as those on the Ge 4/4 II and Ge 4/4 III. The new drive is designed so that scissors-type pantographs (8440023) can be operated for the first time. This makes it possible to retrofit the drive, for example, on the Crocodile (2040x) or the Schnüpftrückerli (2045x). And of course, old or defective drives can now be replaced. A special feature is the pleasantly slow and clearly visible speed when raising and lowering the pantographs. They are not snapped up and down like a pocket knife. And thanks to the integrated spring mechanism, the pantograph can be raised or lowered manually without damaging the mechanism.
On order, lead time to be confirmed
Assembly set for PIKO BR 103 The set consists of the required mounting plates, fixing material and assembly instructions for installing two single-arm pantograph drives 8440012 in the PIKO BR 103. The drives are connected to a decoder in accordance with the instructions. (Drives and decoder not included)
On order, lead time to be confirmed
Assembly set for LGB self-unloading hopper wagons (4161x) The set consists of an assembly plate, assembly and fixing materials, and an instruction manual for fitting a single-arm pantograph drive 8440013 in the LGB self-unloading hopper wagon. The single-arm pantograph drive is modified and programmed according to the instructions before installation. The drive is connected either to the track current (as the decoder is already integrated) or to the function output of a decoder. (Drive and decoder not included in the supply)
On order, lead time to be confirmed
With the 2.0 update, the range of functions of the proven shunting coupling #8442000 has been significantly expanded. In addition to classic operation at the function output of a decoder, the new shunting coupling now also supports true DCC operation. Even if no function output is available on the decoder, or if it is to be used on a wagon without a decoder, the intelligent electronics allow direct control of the shunting coupling 2.0 in the DCC system.
On order, lead time to be confirmed