Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Electronic Accessories

Filter products
Fluorescent lamp-simulator
Viessmann 5067
Fluorescent lamp-simulator

Electronic circuitry for realistic operation of Viessmann fluorescent lighted lamps in all scales. Useable with LED lights, too. After switching on, the fluorescent tubes flicker for a prototypical time until they all reach full output and burn uniformly. Each lamp operates slightly differently. At one of the outputs a defect fluorescent lamp can be simulated. This tube will flicker in irregular intervals, sometimes lighting up quickly and other times very slowly. 5 separate outputs with different starting patterns. Each output can drive 3 lamps. We recommend connection of only one lamp to each output, since no 2 lamps will ever operate exactly the same way in reality. Switching on / off is effected via a separate momentary action switch, e. g. push-button panel item 5547.

Selling price: CHF 33.90 RRP CHF 37.20

On order, lead time to be confirmed

10% off the recommended price
H0 Pantograph flashlight
Viessmann 5068 Scale H0
H0 Pantograph flashlight

Effect simulates the arc discharge of a moving train. Established with very small electronics and blue micro-LED. For easy installation in electric locomotives gauge H0.

Selling price: CHF 35.90 RRP CHF 39.90

On order, lead time to be confirmed

H0 Train rear lanterns with LED, 2 pieces
Viessmann 5069 Scale H0
H0 Train rear lanterns with LED, 2 pieces

Highly detailed functional lantern for epochs II-III fitting H0 scale waggons. Maintenance free by LED lighting. Scope: 2 LED lights with boards, rectifier and 2 resistors.

Selling price: CHF 34.90 RRP CHF 38.30

On order, lead time to be confirmed

10% off the recommended price
H0 Conducting couplers, 4-pole, 1 pair
Viessmann 5071 Scale H0
H0 Conducting couplers, 4-pole, 1 pair

In each coupler 4 conducting contact areas are integrated. Each wire is up to 0,5 A. Used as fixed trainset formation, cannot be uncoupled automatically, yet easy to separate and to couple! Including connection cable. Fitting NEM 362-shaft.

Selling price: CHF 25.90 RRP CHF 29.00

On order, lead time to be confirmed

Multi protocol light decoder
Viessmann 5074
Multi protocol light decoder

Multi-protocol light decoder, item 5074 - maximum versatility, minimal cost! Discover the next generation of lighting control for your model railway layout: With the multi-protocol light decoder, item 5074, you can replace up to 16 individual signal control modules (e. g. for block signals) with a single device – reducing your costs by up to 90%! Your benefits at a glance: Highly versatile: Control a vast range of lighting scenes and effects – from building and industrial illumination to street lamps and specialized effects such as lightning flashes, fireworks, or emergency vehicle dual-flashers. Simple operation: Configuration is effortless using DIP switches (“mouse-pianos”) or – for even greater flexibility – via CV programming. Maximum flexibility: Four independent groups, each with eight overload-protected outputs, can be driven individually or combined into stunning light scenes. Wide effect selection: Each output offers 13 distinct scene types with numerous effects – from flicker-free LED illumination to realistic random effects. Smart control options: Each group features 2 independent analogue control inputs. Additionally, all outputs can be controlled digitally via your central command station. Powerful and safe: Every light output supports up to 100 mA and includes overload protection for reliable, worry-free operation. Compatible with both analogue and digital systems: Full compatibility for seamless integration into your layout. Typical applications: House lighting with realistic random behaviour Colour light signal control TV simulator Industrial or commercial lighting Street lights with start-up, flicker and after-glow effects Campfires, warning flashers, railway crossing lights, chasing lights Special effects including lightning, fireworks, emergency vehicle dual-flash and much more Choose innovation, reduce costs, and illuminate your model railway with item 5074!

Selling price: CHF 119.00 RRP CHF 132.20

On order, lead time to be confirmed

H0 Coach lighting, 11 LEDs yellow, with function decoder
Viessmann 5076 Scale H0
H0 Coach lighting, 11 LEDs yellow, with function decoder

Coach lighting with maintenance free, power-saving, bright LEDs with integrated multi protocol decoder (Motorola/DCC). Brightness adjustable by CVs and potentiometer. Can be used in any coach of all manufacturers designed to be equipped with lighting. By shortening the circuit board, it can be adapted to various waggon lengths. Integrated flickering protection for constant light even with short interruptions of the voltage supply, additional capacitors/power packs can be connected. Various lighting effects are adjustable, as start-up simulation of track bed inverter or single flickering tubes. The model offers direction depending switching outputs for front- and rear lighting. An additional switching output up to 150 mA capacity completes the functionalities. Power supply by grinder/point unit or conducting couplers items 5048/5071. Suitable for DC, AC or digital power. Due to low-loss switching regulator the coach lighting warms up only a bit. Maximum power input 20 mA. Dimensions: L 25,4 x W 0,8 cm.

Selling price: CHF 29.90 RRP CHF 33.20

On order, lead time to be confirmed

H0 Coach lighting, 11 LEDs white, with function decoder
Viessmann 5078 Scale H0
H0 Coach lighting, 11 LEDs white, with function decoder

Coach lighting with maintenance free, power-saving, bright LEDs with integrated multi protocol decoder (Motorola/DCC). Brightness adjustable by CVs and potentiometer. Can be used in any coach of all manufacturers designed to be equipped with lighting. By shortening the circuit board, it can be adapted to various waggon lengths. Integrated flickering protection for constant light even with short interruptions of the voltage supply, additional capacitors/power packs can be connected. Various lighting effects are adjustable, as start-up simulation of track bed inverter or single flickering tubes. The model offers direction depending switching outputs for front- and rear lighting. An additional switching output up to 150 mA capacity completes the functionalities. Power supply by grinder/point unit or conducting couplers items 5048/5071. Suitable for DC, AC or digital power. Due to low-loss switching regulator the coach lighting warms up only a bit. Maximum power input 20 mA. Dimensions: L 25,4 x W 0,8 cm.

Selling price: CHF 29.90 RRP CHF 33.20

On order, lead time to be confirmed

10% off the recommended price
LED house interior lighting with TV-simulation
Viessmann 5079
LED house interior lighting with TV-simulation

Power-saving and maintenance free LED house interior lighting for all model railway buildings. All windows/rooms can be illuminated separately and realistically.The clou: Attached control module and board with special red-blue LEDs create a lifelike TV simulation! The control module is equipped with 4 outputs which allows to connect up to 6 LED-boards. More boards with one LED are available, yellow item 6007, white item 6008, warm-white item 6006 or boards with 2 LEDs for more brightness in white item 6017, yellow item 6018 and warm-white item 6021. Including 3 boards with one white LED, one board with red-blue LEDs for TV simulation, one control electronics and 12 light boxes in 4 different sizes. Dimensions of the light boxes: L 1,7 x W 1,8 x H 2,6 cm, L 1,7 x W 1,6 x H 2,1 cm, L 1,7 x W 1,2 x H 1,9 cm, L 1,7 x W 1,4 x H 2,3 cm.

Selling price: CHF 54.90 RRP CHF 61.00

On order, lead time to be confirmed

11% off the recommended price
H0 Lit platform clock, LED white - replaces 50801
Viessmann 5080 Scale H0
H0 Lit platform clock, LED white - replaces 50801

Timepiece without function. Prototypical brass mast with base socket for easy mounting. Height: 5,6 cm.

Selling price: CHF 17.90 RRP CHF 20.20

On order, lead time to be confirmed

H0 Lit platform clock on lattice mast, LED white, height: 7 cm
Viessmann 5081 Scale H0
H0 Lit platform clock on lattice mast, LED white, height: 7 cm

Timepiece without function. Prototypical lattice mast with base socket for easy mounting. Maintenance free by LED lighting. Height: 7 cm.

Selling price: CHF 30.90 RRP CHF 34.10

On order, lead time to be confirmed

H0 Lit platform clock on lattice mast, LED white, height: 11 cm
Viessmann 5082 Scale H0
H0 Lit platform clock on lattice mast, LED white, height: 11 cm

Timepiece without function. Prototypical lattice mast with base socket for easy mounting. Maintenance free by LED lighting. Height: 11 cm.

Selling price: CHF 31.90 RRP CHF 35.10

On order, lead time to be confirmed

H0 Traffic sign 222 with LED lighting
Viessmann 5085 Scale H0
H0 Traffic sign 222 with LED lighting

This traffic sign (prescribed direction of the traffic) fits ideally epoch III and early epoch IV. With base socket for easy mounting. Maintenance free by LED lighting. Dimensions: L 0,6 x W 0,8 x H 1,9 cm.

Selling price: CHF 27.90 RRP CHF 30.60

On order, lead time to be confirmed

11% off the recommended price
LED light strips 5 mm wide with 42 LEDs white
Viessmann 5088
LED light strips 5 mm wide with 42 LEDs white

These LED light strips are suitable for stationary lighting. They consist of flexible material and are coated on their backs with adhesive tape. Thus they can easily be mounted even in bent condition. The LED strips are intended to be used with power modules 5215, 5225 or 5205 or with DC voltages of 18V or higher. The enclosed resistors allow for brightness adjustment.The max. contact load per segment is 25 mA, the load for the total strip must not exceed 190 mA. Operating voltage with serial resistor: 24V =. Incl. connection cable. The light strip equipped with 42 LEDs consists of 7 separable segments and has a total length of approx. 250 mm. Each segment is approx. 35 mm long and has 6 white LEDs (4000K). The segments are connected in parallel.

Selling price: CHF 16.90 RRP CHF 19.20

On order, lead time to be confirmed

10% off the recommended price
H0, TT N Coach lighting, 8 LEDs yellow
Viessmann 5091 Scale H0
H0, TT N Coach lighting, 8 LEDs yellow

The circuit board with 8 white, maintenance free LEDs can be shortened. Constant power supply integrated, prepared for flicker-protection. Uniform illumination by small LED distance can be used in any coach of all manufacturers designed to be equipped with lighting. Suitable for DC, AC or digital power. Maximum power input 30 mA. Dimensions: L 13,2 x W 0,9 cm.

Selling price: CHF 13.90 RRP CHF 15.60

On order, lead time to be confirmed

H0 Pedestrian signal, 4 pieces
Viessmann 5096 Scale H0
H0 Pedestrian signal, 4 pieces

Pedestrian signal for epochs III – VI. The set contains 4 pedestrian lights, with red and green LEDs, used for pedestrian crosswalks. Prototypical brass mast with base socket for easy mounting. Maintenance free by LED-lighting. The pedestrian signals are useable with traffic lights item 5094 or 5095, which contain the necessary electronic control module. For a full two-street intersection 2 x item 5094 or 2x item 5095 and 1 x item 5096 are required. Height: 4,1 cm.

Selling price: CHF 57.90 RRP CHF 64.00

On order, lead time to be confirmed

H0 Road tunnel classic, with LED mirroring- and depth effect
Viessmann 5097 Scale H0
H0 Road tunnel classic, with LED mirroring- and depth effect

One piece Vollmer stone art street is attached. Length: 18 cm. The tunnel portal is made of Vollmer stone art. Dimensions: L 16,7 x W 9,7 x H 2,2 cm.

Selling price: CHF 59.90 RRP CHF 66.10

On order, lead time to be confirmed

Mini LED light strips 2.3 mm wide with 5 LEDs warm-white, 4 pieces
Viessmann 5158
Mini LED light strips 2.3 mm wide with 5 LEDs warm-white, 4 pieces

These LED light strips are intended solely for stationary lighting applications, such as simulating neon tubes in buildings or at train platforms. They are made from flexible material. The LED strips are designed for operation with the power modules, items 5215, 5225, or 5208, or the LED dimmer, item 5590, or with DC voltages of approx. 18 V and above. The included resistors allow for brightness adjustment. Recommended operating voltage: 24 V DC, total current without series resistor: 9 mA. Connection cable included. The light strip, equipped with 5 warm-white (2200k) LEDs, has a total length of approx. 17 mm.

Selling price: CHF 11.90 RRP CHF 13.00

On order, lead time to be confirmed

Mini LED light strips 2.3 mm wide with 5 LEDs white, 4 pieces
Viessmann 5159
Mini LED light strips 2.3 mm wide with 5 LEDs white, 4 pieces

These LED light strips are intended solely for stationary lighting applications, such as simulating neon tubes in buildings or at train platforms. They are made from flexible material. The LED strips are designed for operation with the power modules, items 5215, 5225, or 5208, or the LED dimmer, item 5590, or with DC voltages of approx. 18 V and above. The included resistors allow for brightness adjustment. Recommended operating voltage: 24 V DC, total current without series resistor: 9 mA. Connection cable included. The light strip, equipped with 5 white (5700k) LEDs, has a total length of approx. 17 mm.

Selling price: CHF 11.90 RRP CHF 13.00

On order, lead time to be confirmed

10% off the recommended price
Power transformer 16 V, 150 VA
Viessmann 5201
Power transformer 16 V, 150 VA

Extremely powerful model train transformer to provide lighting of complete model towns and for controlling magnetic components, for safe switching of various magnetic items (even at the same time). Due to the high power, the use of the high current cable item 6896 (brown) and item 6897 (yellow) is necessary to supply electricity. Integrated overload protection avoids overload and short-circuit breakdown by timeous cut-off of the transformer. Technical data: Input voltage 230 V ~,output voltage 9 and 16 V~, maximum power 150 VA. Dimensions: L 17,9 x W 8,9 x H 8,1 cm.

Selling price: CHF 223.00 RRP CHF 248.00

On order, lead time to be confirmed

Shuttle service control module for AC-trains
Viessmann 5204
Shuttle service control module for AC-trains

Integrated light signal control by prototypical smooth signal pictures. Full automatic and semi-automatic modes are available, in semi-automatic mode the train is started manually with a button. Current situation is shown by 2 LEDs. External power supply, transformer, is required. Provided for analogue locomotives, but limited operation with digital locomotives is possible. This item is not suitable for Märklin metal track. Please contact our customer service.

Selling price: CHF 109.00 RRP CHF 120.80

On order, lead time to be confirmed

10% off the recommended price
Track occupancy detector, 8-sections
Viessmann 5206
Track occupancy detector, 8-sections

To control and support 8 track sections. The outputs can be mounted directly to insulated track sections and detect every consuming vehicle. Suitable for AC- and DC digital voltage. Feedback decoders e. g. item 5217, relays items 5207, 5551, 5552, points and signals with end sections, LEDs or lamps can be connected. Max. load is 3 A for the outputs and 4,5 A for the whole module. Track occupancy detector provides a special track supply, which provides feedback even if the current on the rails is interrupted (trafo reset to zero or after short circuit).

Selling price: CHF 114.00 RRP CHF 127.10

On order, lead time to be confirmed

10% off the recommended price
Time relay
Viessmann 5207
Time relay

For time-triggered operations, e.g. blinking lights, or simulation of train driver’s reaction time after setting a signal to green. Delays for switching on or off are separately adjustable between 0 and 3 minutes. Two simultaneously switching outputs are available, so you can use it for a signal and a train at the same time. Contact load max. current: 2 A each output.

Selling price: CHF 45.90 RRP CHF 51.20

On order, lead time to be confirmed

10% off the recommended price
Colour light signal control module
Viessmann 5210
Colour light signal control module

Suitable to connect all scales of Viessmann standard colour light signals. With this module you can control the aspects of colour light signals without using relays. Optional connection of one signal with more aspects or two signals with 3 aspects. Special technology allows prototypical smooth changing of the signal lights. Optional blanking (distant signal switched off while main signal on the same mast shows “stop” position). One control module replaces up to 7 relays which are required with conventional technology. Without train control, so best used with computer-controlled digital layouts. Controlled by push-button panels items 5546 or 5547, single switch, track contacts or digital decoders are possible.

Selling price: CHF 79.90 RRP CHF 88.80

On order, lead time to be confirmed

10% off the recommended price
Motorola digital switching decoder
Viessmann 5213
Motorola digital switching decoder

Decoder to switch continuous current for colour light signals, lighting, motors, track or accessories. Compatible with Viessmann Commander, Märklin Digital and Uhlenbrock Intellibox. The switches for the setting of 80 possible addresses are accessible from the outside. It has 4 separate and independently controlled relays, max. current 2 A each. Supports both external supply and supply from the digital track.

Selling price: CHF 64.90 RRP CHF 72.40

On order, lead time to be confirmed