Freight wagons
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype Due to the rolling process during their production, sheet steel coils are susceptible to moisture. In the 1970s, seeking to protect such coils from corrosion during transport to processing industries, the rail vehicle industry developed a special type of flatcar with three nested sliding hoods – the Shis 708, which was also known as the Shimmns 708 from 1987 onwards. To allow easy loading of the coils, the hoods can be opened as required, exposing the five loading troughs embedded in the vehicle frame. The Federal Railway placed orders for over 2,500 units of Shis/Shimmns 708 in two major batches. The actual number of vehicles of this design is significantly higher due to additional orders from other state railways and leasing companies. As the hoods became increasingly maintenance-intensive with age, DB AG replaced them with sliding tarpaulins on 1,000 carriages and reclassified these vehicles as the Shimmns-ttu 772 from 2002 onwards. However, private operators continue to utilise some vehicles in their original condition. Model Sliding hoods not movable Lots of design differences Variants with parking and handbrake Lots of extra details Three-point bearing for safe operation Different bogies of several types Variant-appropriate arrangement of the address boards
On order, shipped within 10-15 days
Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports
On order, shipped within 10-15 days
Prototype Innofreight, as the name suggests, is fully committed to innovation in rail freight transport. The company claims that its self-developed InnoWaggons allow freight transport on the railways to be organised more efficiently than ever before. Innofreight achieves this efficiency by offering its InnoWaggons in three different lengths: 2x30 ft, 2x40 ft and 2x45 ft. Each vehicle consists of two short-coupled carrying wagons. The InnoWaggons can be fitted with a variety of different superstructures and transport racks by means of standardised folding container spigots. The wagons can thus be individually equipped and loaded for each customer and, if required, even for each transport assignment. This is certainly a very far-sighted innovation, especially given the increasingly complex approval procedures for rail vehicles. Model Replica of all three InnoWaggons double carriages Replica of the latest generation Y25 bogie Extra mounted brake-switch Fine engravings NEM-standard short-coupling True-to-original replica of the car bottom Wheelsets with inside contours Bogie with three-point support Without loading, for free arrangement
On order, shipped within 10-15 days
Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports
On order, shipped within 10-15 days
Prototype Innofreight, as the name suggests, is fully committed to innovation in rail freight transport. The company claims that its self-developed InnoWaggons allow freight transport on the railways to be organised more efficiently than ever before. Innofreight achieves this efficiency by offering its InnoWaggons in three different lengths: 2x30 ft, 2x40 ft and 2x45 ft. Each vehicle consists of two short-coupled carrying wagons. The InnoWaggons can be fitted with a variety of different superstructures and transport racks by means of standardised folding container spigots. The wagons can thus be individually equipped and loaded for each customer and, if required, even for each transport assignment. This is certainly a very far-sighted innovation, especially given the increasingly complex approval procedures for rail vehicles. Model Replica of all three InnoWaggons double carriages Replica of the latest generation Y25 bogie Extra mounted brake-switch Fine engravings NEM-standard short-coupling True-to-original replica of the car bottom Wheelsets with inside contours Bogie with three-point support Without loading, for free arrangement
On order, shipped within 10-15 days
Prototype Innofreight, as the name suggests, is fully committed to innovation in rail freight transport. The company claims that its self-developed InnoWaggons allow freight transport on the railways to be organised more efficiently than ever before. Innofreight achieves this efficiency by offering its InnoWaggons in three different lengths: 2x30 ft, 2x40 ft and 2x45 ft. Each vehicle consists of two short-coupled carrying wagons. The InnoWaggons can be fitted with a variety of different superstructures and transport racks by means of standardised folding container spigots. The wagons can thus be individually equipped and loaded for each customer and, if required, even for each transport assignment. This is certainly a very far-sighted innovation, especially given the increasingly complex approval procedures for rail vehicles. Model Replica of all three InnoWaggons double carriages Replica of the latest generation Y25 bogie Extra mounted brake-switch Fine engravings NEM-standard short-coupling True-to-original replica of the car bottom Wheelsets with inside contours Bogie with three-point support Without loading, for free arrangement
On order, shipped within 10-15 days
Prototype The association construction types of the German national railway association already included an open-plan covered freight car, which was used in particular for freight with a high weight and low volume. After the foundation of the DRG, the main standard freight cars were redesigned according to the so-called principles of interchangeability. For this the production tolerances were kept so small that it was very easy to change replacement parts. The design of the new open-plan freight car was heavily based on its association type predecessor. The main dimensions such as wheelbase and length over buffers was adopted, as were the two metre wide doors opening to the right, which however were installed suspended. New features included the riveted strut bracing, which allowed a lower design of the longitudinal beam, and the barrel design of the roof instead of the basket arch of the predecessor cars. Some of the cars had a handbrake with brakeman’s cab and/or variable gauge wheel sets for adaptation to Russian wide gauge, identifiable by the white painted buffer sleeves and the sub-class mark "r". All covered open-plan cars were allocated to the "Dresden" class district. As already mentioned, the cars were particularly suitable for light freight with large volumes (e.g. glass industry). When the design was revised later, a few changes were made, for example longer and softer suspension springs, which allowed higher speeds and therefore also use in passenger trains. Due to the turmoil of the war, not only the two German railway administrations but also many other European railways had cars of this type in their stock after 1945. The last ones were only retired in the 1980s - proof of the quality and durability of the design. Model Axle holders made of embossed sheet metal Individually mounted wheelchocks Fine replica of the wheel bearing Individually mounted brake switch NEM-standard short-coupling True to original car bottom Wheelsets with inside contours
On order, shipped within 10-15 days
Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports
On order, shipped within 10-15 days
Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports
On order, shipped within 10-15 days
Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports
On order, shipped within 10-15 days
Prototype Ritter Sport is now known and loved not only in Germany, but all over the world. In 1912, Clara and Alfred Eugen Ritter founded the company in Stuttgart-Bad Cannstatt. Thanks to a suggestion by Clara Ritter, the iconic square chocolate was introduced in 1932. This innovative shape was not only practical for transportation, but is still a trademark that sets Ritter Sport apart from other chocolate manufacturers today. “Square. Practical. Good.” – describes not only the characteristic shape of the chocolate, but also the practical advantages and high quality of the products. The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports
On order, shipped within 10-15 days
Prototype Rotkäppchen Sektkellerei has its origins in Freyburg an der Unstrut in 1856. Founded by brothers Moritz and Julius Kloss together with their friend Carl Foerster, Sektkellerei Kloss und Foerster specialized in the production of sparkling wines. Due to a new law in 1894, the iconic red capsule became the new brand name. “Rotkäppchen Sekt” became one of the first German brands to be registered and still exists today. The company is now part of the Rotkäppchen-Mumm Group and stands for tradition, quality, and enjoyment. The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports
On order, shipped within 10-15 days