Templates, spacers and posts
For laying multi-track lines, the H segments ensure correct spacing and concentricity of the tracks. They are slid onto the rails, placed closer together on curves and further apart on straights, until the tracks are screwed down or fixed with Hacker glue (CA). The set contains 12 pieces for N 33.6 gauge.
On order
For laying multi-track lines, the R segments ensure correct spacing and concentricity of the tracks in the Rondela N helix. They are slid onto the rails, placed closer together on curves and further apart on straights, until the tracks are screwed down or fixed with Hacker glue (CA). The set contains 12 pieces.
On order
Railing wire measuring 2 x 960 mm, including connector, 5 pieces per pack.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load. Base support - no. 1-12, height 27.3 to 128.1mm, set of 12 pairs
On order
Extension – height 110 mm + coupling, 24 pairs. The mounting stands are suitable for the next level of Rondela as well as for the track level.
On order
These universal supports made of special foam belong to the Hacker I-Track system and allow easy mounting of I-Track segments or other constructions. They are simply shortened to the desired length with a knife and mounted with hot melt glue or Hacker CA adhesive.
On order
These universal supports made of special foam belong to the Hacker I-Track system and allow easy mounting of I-Track segments or other constructions. They are simply shortened to the desired length with a knife and mounted with hot melt glue or Hacker CA adhesive.
On order
SE supports are used to mount the upper transition segments of the Rondela helix, which create a smooth transition from the gradient to the level section. This version is designed for the Rondela 360° version (1 base circle). The SR extension supports allow all supports to be raised by one or more levels.
On order
SE supports are used to mount the upper transition segments of the Rondela helix, which create a smooth transition from the gradient to the level section. This version is designed for the Rondela 540° version (1.5 base circles). The SR extension supports allow all supports to be raised by one or more levels.
On order
If no railing is used, close off the support with part Z. This part is used to fix the track segment to the support.
On order
Holder for securing the position of the assembled parts during construction, 24 pcs.
On order