Templates, spacers and posts
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy mounting of our I-Track segments or other constructions. The supports are available in two versions: wooden supports and universal supports. The universal supports are made of a special foam and measure 60x40x600mm or 25x40x600mm. The universal supports are simply cut to the desired length with a knife. They are then mounted with hot-melt glue or our Hacker CA adhesive. The wooden supports consist of several parts and can therefore be assembled individually. The individual parts are simply pushed into one another. In this way, for example, multi-level supports can be built entirely to your needs. The individual parts only need to be glued after assembly, so you can be sure that the supports will also fit your layout. To glue the wooden parts, use standard wood glue or our Hacker superglue. The lengths of the supports vary depending on the scale and are based on the respective height increments of our Rondela track helix system - Äh = 110mm (H0), Äh = 71mm (TT), Äh = 52.5mm (N). The supports are offered as kits, including screws for mounting the base, in various sets. E.g. sets with supports of the same height for building level trackbeds, with 12 pairs of one support height each (S1, S2, ..., S12). As a set for building gradients / downgrades, with one pair of each support height (S1 - S12, which follow the lower transition segment). For the upper transition segments of Rondela there are the SE supports. These are used to mount the upper transition segments, which achieve a gentle transition from the gradient to level track (see chapter – Transition segments). SE supports are available for the Rondela versions 360° (1 base circle) and 540° (1.5 base circles). With the SR extension supports, you can raise all supports by one or more levels. To mount our railing made of 2mm aluminium wire, simply use the grooves already provided for this purpose on the supports, or the separate railing brackets FA. When assembling the individual I-Track segments, they are fixed with the holder H until you have glued them. On curves we recommend positioning a support every 30°. For straight gradients / downgrades, position the individual supports so that you do not exceed the maximum gradient recommended for your gauge. For level, straight sections of line, choose the spacing between the supports so that the I-Track segments do not sag under load.
On order
The Hacker I-Track system also includes supports for easy assembly of the I-Track segments or other constructions, available as wooden supports or universal supports. The wooden supports consist of several interlocking parts that are glued together after assembly, allowing multi-tier supports to be built as needed.
On order
Set of 12 railing brackets.
On order
Extension set with height 52.5 mm and coupling K, 12 pieces. The support stands are suitable for the next level of the Rondela as well as for the track level.
On order
Extension set with height 52.5 mm and coupling, 4 pieces. The support stands are suitable for the next level of the Rondela as well as for the track level.
On order
The I-Track BF spacers ensure that tracks with roadbed are placed at the correct distance and coaxially to each other on flat baseboards. They are designed for use with the curved or straight I-Track templates. Spacer BF 77.5 mm for Märklin C+K tracks, 12 pieces.
On order
For laying multi-track sections, the H spacers ensure the mutual distance and concentricity of the tracks. They are slid onto the rails, placed closer together on curves and further apart on straight sections, before the tracks are screwed down or glued to the base with Hacker adhesive (CA). They are then removed again and reused for laying further tracks. The set contains 12 pieces for Märklin C+K track, 77.5 mm spacing.
On order
I-Track R spacers for the Rondela helix, 12 pieces. For laying multi-track sections, the R spacers ensure the mutual distance and concentricity of the tracks. They are slid onto the rails, placed closer together on curves and further apart on straight sections, before the tracks are screwed down or glued to the base with Hacker adhesive (CA). They are then removed again and reused for laying further tracks.
On order
When laying single or multi-track lines, the correct radius, mutual spacing and coaxiality of the tracks with ballast bed must be ensured. The I-Track BF spacers ensure correct track placement on flat baseboards and are designed for use with the curved or straight I-Track templates.
On order
The H spacer ensures the mutual distance and concentricity of the tracks when laying multi-track routes. The H segments are slid onto the rails and removed again once the tracks are screwed or glued down. The set contains 12 H segments for Märklin C+K tracks with 64.3 mm spacing.
On order
The I-Track R spacer for the Rondela helix ensures the mutual distance and concentricity of the tracks when laying multi-track routes. The R segments are slid onto the rails and removed again once the tracks are screwed or glued down. The set contains 12 R segments for Märklin C+K tracks with 64.3 mm spacing.
On order