Rolling Stock
Prototype Following the models 130 (maximum speed 140 km/h) and 131 (100 km/h), the DB put the 132 model (120 km/h) into service after 1974 with the electric heating system. Thanks to its configuration, the DR had found its optimum machine. This is why the DR acquired 709 locomotives from the factory in Woroschilowgrad. After a few initial teething problems, the technical service finally had a reliable and multifunctional machine. Model Rear signals True to original sound True-to-original speed 5-pole motor All axles driven Standard shaft to NEM 355 Reproduction of cooling van Finely engraved details
On order, shipped within 10-15 days
Prototype After the annexation of Austria, the E44 locomotives were supposed to be used also on the alpine routes of the „Ostmark“. In order to minimize the brake block wear during downhill ride, the installation of an electric dynamic brake was required. The German National Railway (DRB) ordered such an additional device for the machines of the batch E44 152 - 191 and referred to the subtype as E44W for „Widerstandsbremse“ (dynamic brake). Because of the war, only the models E44W 152 - 183 were delivered between 1943 and 1951. Externally, the machines attracted attention primarily by the roof- mounted vent stacks of the dynamic brakes. After 1945, the German Railway (DB) maintained the dynamic brake only for the 16 Freiburg- based locomotives, which were used on the Höllental railway track, and referred to these as E44.11 from 1962 onwards, and as BR 145 after 1968. On all other machines, the electric brake was removed or, in case of a damage, decommissioned. The machines E44 1170 and 1180 survived; we can only hope that one of them will once again „hum“ past the Hirschsprung (location where a stag is said to have leapt over the Höllental). Model Detailed body Fine engravings and rivets Many extra mounted parts, such as handles, ladders and multi-part cooling coil Reproduction of the driver´s cab Precise replica of the bogies Separately mounted brake cylinder, brake pull rod, sand box and cowcatcher Precise replica of the roof, versions with normal and extended roof Prototypical roof-fittings, with many individually mounted parts Free-standing roof lines Various insulators Different main switch types Finely detailed pantographs True-to-original length of the roof walkways Bogie with three-point support Fine paintwork and painting 3rd front light can be switched on or off also in analog mode Driver's cab with LED lighting and in the sound version also in the machine room NEM-standard short coupling Analog models with Next18 interface Soundversion: all light functions can be switched on and off in digital mode, also machine roof lighting; optimal motor and load control for perfect running characteristics; noiseless 16-bit sound with up to 8 independent channels thanks to latest sound technology and excellent sound characteristics; compatible with all established digital systems (DCC, Motorola, SX1 und SX2); sound decoder on the main circuit board Modell: pantograph type SBS 39; main swith type R 628; with 8 sand boxes, indusi and extended roof; with dynamic brake for the first time in a model (deviating photo)
On order, shipped within 10-15 days
Detailed body Fine engravings and rivets Many extra mounted parts, such as handles, ladders and multi-part cooling coil Reproduction of the driver´s cab Precise replica of the bogies Separately mounted brake cylinder, brake pull rod, sand box and cowcatcher Precise replica of the roof, versions with normal and extended roof Prototypical roof-fittings, with many individually mounted parts Free-standing roof lines Various insulators Different main switch types Finely detailed pantographs True-to-original length of the roof walkways Bogie with three-point support Fine paintwork and painting 3rd front light can be switched on or off also in analog mode Driver's cab with LED lighting and in the sound version also in the machine room NEM-standard short coupling Analog models with Next18 interface Soundversion: all light functions can be switched on and off in digital mode, also machine roof lighting; optimal motor and load control for perfect running characteristics; noiseless 16-bit sound with up to 8 independent channels thanks to latest sound technology and excellent sound characteristics; compatible with all established digital systems (DCC, Motorola, SX1 und SX2); sound decoder on the main circuit board Modell: pantograph type SBS 39; main swith type R 628; with 8 sand boxes, indusi and extended roof; with dynamic brake for the first time in a model (deviating photo)
On order, lead time to be confirmed
Detailed body Fine engravings and rivets Many extra mounted parts, such as handles, ladders and multi-part cooling coil Reproduction of the driver´s cab Precise replica of the bogies Separately mounted brake cylinder, brake pull rod, sand box and cowcatcher Precise replica of the roof, versions with normal and extended roof Prototypical roof-fittings, with many individually mounted parts Free-standing roof lines Various insulators Different main switch types Finely detailed pantographs True-to-original length of the roof walkways Bogie with three-point support Fine paintwork and painting 3rd front light can be switched on or off also in analog mode Driver's cab with LED lighting and in the sound version also in the machine room NEM-standard short coupling Analog models with Next18 interface Soundversion: all light functions can be switched on and off in digital mode, also machine roof lighting; optimal motor and load control for perfect running characteristics; noiseless 16-bit sound with up to 8 independent channels thanks to latest sound technology and excellent sound characteristics; compatible with all established digital systems (DCC, Motorola, SX1 und SX2); sound decoder on the main circuit board Modell: pantograph type SBS 39; main swith type R 628; with 8 sand boxes, indusi and extended roof; with dynamic brake for the first time in a model (deviating photo)
On order, lead time to be confirmed
Prototype After the annexation of Austria, the E44 locomotives were supposed to be used also on the alpine routes of the „Ostmark“. In order to minimize the brake block wear during downhill ride, the installation of an electric dynamic brake was required. The German National Railway (DRB) ordered such an additional device for the machines of the batch E44 152 - 191 and referred to the subtype as E44W for „Widerstandsbremse“ (dynamic brake). Because of the war, only the models E44W 152 - 183 were delivered between 1943 and 1951. Externally, the machines attracted attention primarily by the roof- mounted vent stacks of the dynamic brakes. After 1945, the German Railway (DB) maintained the dynamic brake only for the 16 Freiburg- based locomotives, which were used on the Höllental railway track, and referred to these as E44.11 from 1962 onwards, and as BR 145 after 1968. On all other machines, the electric brake was removed or, in case of a damage, decommissioned. The machines E44 1170 and 1180 survived; we can only hope that one of them will once again „hum“ past the Hirschsprung (location where a stag is said to have leapt over the Höllental). Model Detailed body Fine engravings and rivets Many extra mounted parts, such as handles, ladders and multi-part cooling coil Reproduction of the driver´s cab Precise replica of the bogies Separately mounted brake cylinder, brake pull rod, sand box and cowcatcher Precise replica of the roof, versions with normal and extended roof Prototypical roof-fittings, with many individually mounted parts Free-standing roof lines Various insulators Different main switch types Finely detailed pantographs True-to-original length of the roof walkways Bogie with three-point support Fine paintwork and painting 3rd front light can be switched on or off also in analog mode Driver's cab with LED lighting and in the sound version also in the machine room NEM-standard short coupling Analog models with Next18 interface Soundversion: all light functions can be switched on and off in digital mode, also machine roof lighting; optimal motor and load control for perfect running characteristics; noiseless 16-bit sound with up to 8 independent channels thanks to latest sound technology and excellent sound characteristics; compatible with all established digital systems (DCC, Motorola, SX1 und SX2); sound decoder on the main circuit board Modell: pantograph type SBS 39; main swith type R 628; with 8 sand boxes, indusi and extended roof; with dynamic brake for the first time in a model (deviating photo)
On order, shipped within 10-15 days
Detailed body Fine engravings and rivets Many extra mounted parts, such as handles, ladders and multi-part cooling coil Reproduction of the driver´s cab Precise replica of the bogies Separately mounted brake cylinder, brake pull rod, sand box and cowcatcher Precise replica of the roof, versions with normal and extended roof Prototypical roof-fittings, with many individually mounted parts Free-standing roof lines Various insulators Different main switch types Finely detailed pantographs True-to-original length of the roof walkways Bogie with three-point support Fine paintwork and painting 3rd front light can be switched on or off also in analog mode Driver's cab with LED lighting and in the sound version also in the machine room NEM-standard short coupling Analog models with Next18 interface Soundversion: all light functions can be switched on and off in digital mode, also machine roof lighting; optimal motor and load control for perfect running characteristics; noiseless 16-bit sound with up to 8 independent channels thanks to latest sound technology and excellent sound characteristics; compatible with all established digital systems (DCC, Motorola, SX1 und SX2); sound decoder on the main circuit board Modell: pantograph type SBS 39; main swith type R 628; with 4 sand boxes
On order, shipped within 10-15 days
Prototype At the end of the 1920s, it became clear that Deutsche Reichsbahn Gesellschaft (DRG) would have to acquire new electric locomotives, among other things, to accelerate its goods traffic. The need to increase maximum speeds to at least 80 km/h could not be met with the most recently purchased E77 and E75 series since the standard drive technology by means of bars and additional trailing wheelsets did not allow for higher speeds. The good experiences from abroad and with the two Bavarian EG 1 with the Bo’Bo’ two-bogie locomotives convinced the DRG to deviate from single-frame construction as well. The arrival of the world economic crisis in 1929, however, put a halt to this plan by interrupting the cost- intensive electrical expansion of the lines, thus eliminating the need for electric locomotives. The locomotive industry in Germany, however, feared falling behind current developments due to this pause in procurement. They therefore began developing a cheaper design at their own costs. Thus a prototype with the designation E44 70 was created at the Siemens-Schuckert Works (SSW) under the general management of Walter Reichel. This prototype later became the E44 001. SSW was able to integrate its experience with electric arc welding from its production of components for electric generators into locomotive manufacturing, which led to significant savings in materials and manufacturing costs. The prototype’s positive test results convinced DRG to further develop the new locomotive type into a universal locomotive. The result was Germany’s first two-bogie electric locomotive produced in series, which can safely be categorised as the prototype for the subsequently developed standard electric locomotive of Deutsche Bundesbahn (DB). Due to the war the delivery of the locomotives, which were registered for 90 km/h, stretched from 1933 into the postwar period, and Henschel only handed over the last one, a E44 187G, to DB on 29 November 1954. The predominant distribution to central and southern Germany led to the fact that approximately 100 locomotives remained in West Germany and around 50 in East Germany after the war. The most conspicuous design changes at DB were the lengthening of the roof shield for accident prevention and the Indusi (inductive train control system) equipment. The last locomotives, however, remained in service until 1985. Of the original 187 locomotives, only 21 still exist today, partially as museum locomotives and as spare parts donors. Model Detailed body Fine engravings and rivets Many extra mounted parts, such as handles, ladders and multi-part cooling coil Reproduction of the driver´s cab Precise replica of the bogies Separately mounted brake cylinder, brake pull rod, sand box and cowcatcher Precise replica of the roof, versions with normal and extended roof Prototypical roof-fittings, with many individually mounted parts Free-standing roof lines Various insulators Different main switch types Finely detailed pantographs True-to-original length of the roof walkways Bogie with three-point support Fine paintwork and painting 3rd front light can be switched on or off also in analog mode Driver's cab with LED lighting and in the sound version also in the machine room NEM-standard short coupling Analog models with Next18 interface Soundversion: all light functions can be switched on and off in digital mode, also machine roof lighting; optimal motor and load control for perfect running characteristics; noiseless 16-bit sound with up to 8 independent channels thanks to latest sound technology and excellent sound characteristics; compatible with all established digital systems (DCC, Motorola, SX1 und SX2); sound decoder on the main circuit board Modell: pantograph type SBS 39; main swith type R 62; with 8 sand boxes; with dynamic brake for the first time in a model (deviating photo)
On order, shipped within 10-15 days
Prototype At the end of the 1920s, it became clear that Deutsche Reichsbahn Gesellschaft (DRG) would have to acquire new electric locomotives, among other things, to accelerate its goods traffic. The need to increase maximum speeds to at least 80 km/h could not be met with the most recently purchased E77 and E75 series since the standard drive technology by means of bars and additional trailing wheelsets did not allow for higher speeds. The good experiences from abroad and with the two Bavarian EG 1 with the Bo’Bo’ two-bogie locomotives convinced the DRG to deviate from single-frame construction as well. The arrival of the world economic crisis in 1929, however, put a halt to this plan by interrupting the cost- intensive electrical expansion of the lines, thus eliminating the need for electric locomotives. The locomotive industry in Germany, however, feared falling behind current developments due to this pause in procurement. They therefore began developing a cheaper design at their own costs. Thus a prototype with the designation E44 70 was created at the Siemens-Schuckert Works (SSW) under the general management of Walter Reichel. This prototype later became the E44 001. SSW was able to integrate its experience with electric arc welding from its production of components for electric generators into locomotive manufacturing, which led to significant savings in materials and manufacturing costs. The prototype’s positive test results convinced DRG to further develop the new locomotive type into a universal locomotive. The result was Germany’s first two-bogie electric locomotive produced in series, which can safely be categorised as the prototype for the subsequently developed standard electric locomotive of Deutsche Bundesbahn (DB). Due to the war the delivery of the locomotives, which were registered for 90 km/h, stretched from 1933 into the postwar period, and Henschel only handed over the last one, a E44 187G, to DB on 29 November 1954. The predominant distribution to central and southern Germany led to the fact that approximately 100 locomotives remained in West Germany and around 50 in East Germany after the war. The most conspicuous design changes at DB were the lengthening of the roof shield for accident prevention and the Indusi (inductive train control system) equipment. The last locomotives, however, remained in service until 1985. Of the original 187 locomotives, only 21 still exist today, partially as museum locomotives and as spare parts donors. Model Detailed body Fine engravings and rivets Many extra mounted parts, such as handles, ladders and multi-part cooling coil Reproduction of the driver´s cab Precise replica of the bogies Separately mounted brake cylinder, brake pull rod, sand box and cowcatcher Precise replica of the roof, versions with normal and extended roof Prototypical roof-fittings, with many individually mounted parts Free-standing roof lines Various insulators Different main switch types Finely detailed pantographs True-to-original length of the roof walkways Bogie with three-point support Fine paintwork and painting 3rd front light can be switched on or off also in analog mode Driver's cab with LED lighting and in the sound version also in the machine room NEM-standard short coupling Analog models with Next18 interface Soundversion: all light functions can be switched on and off in digital mode, also machine roof lighting; optimal motor and load control for perfect running characteristics; noiseless 16-bit sound with up to 8 independent channels thanks to latest sound technology and excellent sound characteristics; compatible with all established digital systems (DCC, Motorola, SX1 und SX2); sound decoder on the main circuit board Modell: pantograph type SBS 39; main swith type R 62; with 8 sand boxes; with dynamic brake for the first time in a model (deviating photo)
On order, shipped within 10-15 days
Prototype At the end of the 1920s, it became clear that Deutsche Reichsbahn Gesellschaft (DRG) would have to acquire new electric locomotives, among other things, to accelerate its goods traffic. The need to increase maximum speeds to at least 80 km/h could not be met with the most recently purchased E77 and E75 series since the standard drive technology by means of bars and additional trailing wheelsets did not allow for higher speeds. The good experiences from abroad and with the two Bavarian EG 1 with the Bo’Bo’ two-bogie locomotives convinced the DRG to deviate from single-frame construction as well. The arrival of the world economic crisis in 1929, however, put a halt to this plan by interrupting the cost- intensive electrical expansion of the lines, thus eliminating the need for electric locomotives. The locomotive industry in Germany, however, feared falling behind current developments due to this pause in procurement. They therefore began developing a cheaper design at their own costs. Thus a prototype with the designation E44 70 was created at the Siemens-Schuckert Works (SSW) under the general management of Walter Reichel. This prototype later became the E44 001. SSW was able to integrate its experience with electric arc welding from its production of components for electric generators into locomotive manufacturing, which led to significant savings in materials and manufacturing costs. The prototype’s positive test results convinced DRG to further develop the new locomotive type into a universal locomotive. The result was Germany’s first two-bogie electric locomotive produced in series, which can safely be categorised as the prototype for the subsequently developed standard electric locomotive of Deutsche Bundesbahn (DB). Due to the war the delivery of the locomotives, which were registered for 90 km/h, stretched from 1933 into the postwar period, and Henschel only handed over the last one, a E44 187G, to DB on 29 November 1954. The predominant distribution to central and southern Germany led to the fact that approximately 100 locomotives remained in West Germany and around 50 in East Germany after the war. The most conspicuous design changes at DB were the lengthening of the roof shield for accident prevention and the Indusi (inductive train control system) equipment. The last locomotives, however, remained in service until 1985. Of the original 187 locomotives, only 21 still exist today, partially as museum locomotives and as spare parts donors. Model Detailed body Fine engravings and rivets Many extra mounted parts, such as handles, ladders and multi-part cooling coil Reproduction of the driver´s cab Precise replica of the bogies Separately mounted brake cylinder, brake pull rod, sand box and cowcatcher Precise replica of the roof, versions with normal and extended roof Prototypical roof-fittings, with many individually mounted parts Free-standing roof lines Various insulators Different main switch types Finely detailed pantographs True-to-original length of the roof walkways Bogie with three-point support Fine paintwork and painting 3rd front light can be switched on or off also in analog mode Driver's cab with LED lighting and in the sound version also in the machine room NEM-standard short coupling Analog models with Next18 interface Soundversion: all light functions can be switched on and off in digital mode, also machine roof lighting; optimal motor and load control for perfect running characteristics; noiseless 16-bit sound with up to 8 independent channels thanks to latest sound technology and excellent sound characteristics; compatible with all established digital systems (DCC, Motorola, SX1 und SX2); sound decoder on the main circuit board Modell: pantograph type SBS 39; main swith type R 62; with 8 sand boxes; with dynamic brake for the first time in a model (deviating photo)
On order, shipped within 10-15 days
Prototype At the end of the 1920s, it became clear that Deutsche Reichsbahn Gesellschaft (DRG) would have to acquire new electric locomotives, among other things, to accelerate its goods traffic. The need to increase maximum speeds to at least 80 km/h could not be met with the most recently purchased E77 and E75 series since the standard drive technology by means of bars and additional trailing wheelsets did not allow for higher speeds. The good experiences from abroad and with the two Bavarian EG 1 with the Bo’Bo’ two-bogie locomotives convinced the DRG to deviate from single-frame construction as well. The arrival of the world economic crisis in 1929, however, put a halt to this plan by interrupting the cost- intensive electrical expansion of the lines, thus eliminating the need for electric locomotives. The locomotive industry in Germany, however, feared falling behind current developments due to this pause in procurement. They therefore began developing a cheaper design at their own costs. Thus a prototype with the designation E44 70 was created at the Siemens-Schuckert Works (SSW) under the general management of Walter Reichel. This prototype later became the E44 001. SSW was able to integrate its experience with electric arc welding from its production of components for electric generators into locomotive manufacturing, which led to significant savings in materials and manufacturing costs. The prototype’s positive test results convinced DRG to further develop the new locomotive type into a universal locomotive. The result was Germany’s first two-bogie electric locomotive produced in series, which can safely be categorised as the prototype for the subsequently developed standard electric locomotive of Deutsche Bundesbahn (DB). Due to the war the delivery of the locomotives, which were registered for 90 km/h, stretched from 1933 into the postwar period, and Henschel only handed over the last one, a E44 187G, to DB on 29 November 1954. The predominant distribution to central and southern Germany led to the fact that approximately 100 locomotives remained in West Germany and around 50 in East Germany after the war. The most conspicuous design changes at DB were the lengthening of the roof shield for accident prevention and the Indusi (inductive train control system) equipment. The last locomotives, however, remained in service until 1985. Of the original 187 locomotives, only 21 still exist today, partially as museum locomotives and as spare parts donors. Model Detailed body Fine engravings and rivets Many extra mounted parts, such as handles, ladders and multi-part cooling coil Reproduction of the driver´s cab Precise replica of the bogies Separately mounted brake cylinder, brake pull rod, sand box and cowcatcher Precise replica of the roof, versions with normal and extended roof Prototypical roof-fittings, with many individually mounted parts Free-standing roof lines Various insulators Different main switch types Finely detailed pantographs True-to-original length of the roof walkways Bogie with three-point support Fine paintwork and painting 3rd front light can be switched on or off also in analog mode Driver's cab with LED lighting and in the sound version also in the machine room NEM-standard short coupling Analog models with Next18 interface Soundversion: all light functions can be switched on and off in digital mode, also machine roof lighting; optimal motor and load control for perfect running characteristics; noiseless 16-bit sound with up to 8 independent channels thanks to latest sound technology and excellent sound characteristics; compatible with all established digital systems (DCC, Motorola, SX1 und SX2); sound decoder on the main circuit board Modell: pantograph type SBS 39; main swith type R 62; with 8 sand boxes; with dynamic brake for the first time in a model (deviating photo)
On order, shipped within 10-15 days
Body with panorama window With interface (digital version with decoder, analog version with soldering points) Free view into the passenger compartment True to original lighting Three-point support Power take-up via wheel loop Conducting coupling Light between wagon units can be switched off (analog and digital) With interior lighting and fittings Digital versions: decoder and loudspeaker in the engine car; with taillights and headlights; trailer true to original only with red taillights
On order, shipped within 10-15 days
Body with panorama window With interface (digital version with decoder, analog version with soldering points) Free view into the passenger compartment True to original lighting Three-point support Power take-up via wheel loop Conducting coupling Light between wagon units can be switched off (analog and digital) With interior lighting and fittings Digital versions: decoder and loudspeaker in the engine car; with taillights and headlights; trailer true to original only with red taillights
On order, shipped within 10-15 days
Body with panorama window With interface (digital version with decoder, analog version with soldering points) Free view into the passenger compartment True to original lighting Three-point support Power take-up via wheel loop Conducting coupling Light between wagon units can be switched off (analog and digital) With interior lighting and fittings Digital versions: decoder and loudspeaker in the engine car; with taillights and headlights; trailer true to original only with red taillights
On order, shipped within 10-15 days
Body with panorama window With interface (digital version with decoder, analog version with soldering points) Free view into the passenger compartment True to original lighting Three-point support Power take-up via wheel loop Conducting coupling Light between wagon units can be switched off (analog and digital) With interior lighting and fittings Digital versions: decoder and loudspeaker in the engine car; with taillights and headlights; trailer true to original only with red taillights
On order, shipped within 10-15 days
Prototype At the end of 2010, Bombardier Transportation obtained an order for 27 five-part Bombardier TWINDEXX Vario double-decker push-pull trains belonging to the 2010 generation. The block trains with comfortable equipment for long-distance traffic consist of three 2nd class middle wagons, one 1st class middle wagon and one 2nd class control car respectively. The TWINDEXX Vario is a further development of the tried-and-trusted double-decker platform from Görlitz. Each train has 468 seats, 70 of which are in 1st class as well as 9 bicycle parking spaces. The top speed of the trains is 160 km/h. The equipment of the double-decker trains for use in long-distance traffic will correspond to the level of comfort found in ICE trains. Model Exactly scale 1:160 True-to-original length over buffer Structure made of high-quality, impact-resistant plastic Metal bottom plate Printed window frames In-plane assembled windows Illuminated destination indicator (digital) Lighting with warm white LEDs Long-distance headlights (digital) True-to-scale details Perfectly replicated three-dimensional front Finely engraved details Fine paintwork and painting Illuminated driver's cab With interior fittings, incl. driver's cab NEM-standard close coupling Light change white/red, in the direction of travel For digital operation, decoder are required for each individual vehicle - Middle Car: Order no. 0019695.01; Control Car: Order no. 0019695.02 (Operating the vehicle without decoder in digital mode can result in damage to the electronics)
On order, shipped within 10-15 days
Prototype At the end of 2010, Bombardier Transportation obtained an order for 27 five-part Bombardier TWINDEXX Vario double-decker push-pull trains belonging to the 2010 generation. The block trains with comfortable equipment for long-distance traffic consist of three 2nd class middle wagons, one 1st class middle wagon and one 2nd class control car respectively. The TWINDEXX Vario is a further development of the tried-and-trusted double-decker platform from Görlitz. Each train has 468 seats, 70 of which are in 1st class as well as 9 bicycle parking spaces. The top speed of the trains is 160 km/h. The equipment of the double-decker trains for use in long-distance traffic will correspond to the level of comfort found in ICE trains. Model Exactly scale 1:160 True-to-original length over buffer Structure made of high-quality, impact-resistant plastic Metal bottom plate Printed window frames In-plane assembled windows Illuminated destination indicator (digital) Lighting with warm white LEDs True-to-scale details Finely engraved details Fine paintwork and painting NEM-standard close coupling For digital operation, decoder (order no. 0019695.01) are required for each individual vehicle (Operating the vehicle without decoder in digital mode can result in damage to the electronics)
On order, shipped within 10-15 days
Prototype At the end of 2010, Bombardier Transportation obtained an order for 27 five-part Bombardier TWINDEXX Vario double-decker push-pull trains belonging to the 2010 generation. The block trains with comfortable equipment for long-distance traffic consist of three 2nd class middle wagons, one 1st class middle wagon and one 2nd class control car respectively. The TWINDEXX Vario is a further development of the tried-and-trusted double-decker platform from Görlitz. Each train has 468 seats, 70 of which are in 1st class as well as 9 bicycle parking spaces. The top speed of the trains is 160 km/h. The equipment of the double-decker trains for use in long-distance traffic will correspond to the level of comfort found in ICE trains. Model Exactly scale 1:160 True-to-original length over buffer Structure made of high-quality, impact-resistant plastic Metal bottom plate Printed window frames In-plane assembled windows Illuminated destination indicator (digital) Lighting with warm white LEDs True-to-scale details Finely engraved details Fine paintwork and painting NEM-standard close coupling For digital operation, decoder (order no. 0019695.01) are required for each individual vehicle (Operating the vehicle without decoder in digital mode can result in damage to the electronics)
On order, shipped within 10-15 days
Prototype For many years now, double-decker trains have successfully formed the backbone of regional traffic. Double-decker trains are the ideal solution, especially on routes with low platform lengths and a high volume of passengers. The tried-and-tested single-wagon concept of the TWINDEXX Vario double-decker fleet is now being supplemented with an electrical railcar. Bombardier Transportation will supply 16 Bombardier TWINDEXX Vario railcars with regional train equipment to Deutsche Bahn AG. The new four-part railcars from the "Do 2010" generation consist of 2 railcars and 2 middle wagons respectively. With the newly-developed driven TWINDEXX Vario railcar, it is now possible to utilise the trains as pure double-decker multiple unit trains. As a result, it is also possible to use this vehicle as an electric multiple unit train alongside the classic push-pull operation with an electric or diesel locomotive. This railcar can be combined with middle wagons and control cars depending upon the application and desired capacity. The central buffer coupling enables operation with double traction and, as a result, the implementation of a wing-train concept. The trains with a combined upper and lower entrance are comfortably equipped with generous seat spacing and plenty of storage space. Furthermore, the double-decker individual wagons permit the extension and shortening of the block train and, consequently, an adjustment to fluctuating demand or future development. As a result, they can be utilised for the most diverse of operational applications in both regional and long-distance traffic. Model Exact scale 1:160 Illuminated passenger compartment Structure made of high-quality, impact-resistant plastic Metal bottom plate Lighting with white LEDs Illuminated destination indicator (analog permanently on, digitally switchable) Long-distance headlights (can only be used digitally with decoder) Perfectly replicated three-dimensional front Illuminated driver's cab (only with decoder) With interior fittings, incl. driver's cab NEM-standard close coupling Light change white/red, in the direction of travel
On order, shipped within 10-15 days
Prototype For many years now, double-decker trains have successfully formed the backbone of regional traffic. Double-decker trains are the ideal solution, especially on routes with low platform lengths and a high volume of passengers. The tried-and-tested single-wagon concept of the TWINDEXX Vario double-decker fleet is now being supplemented with an electrical railcar. Bombardier Transportation will supply 16 Bombardier TWINDEXX Vario railcars with regional train equipment to Deutsche Bahn AG. The new four-part railcars from the "Do 2010" generation consist of 2 railcars and 2 middle wagons respectively. With the newly-developed driven TWINDEXX Vario railcar, it is now possible to utilise the trains as pure double-decker multiple unit trains. As a result, it is also possible to use this vehicle as an electric multiple unit train alongside the classic push-pull operation with an electric or diesel locomotive. This railcar can be combined with middle wagons and control cars depending upon the application and desired capacity. The central buffer coupling enables operation with double traction and, as a result, the implementation of a wing-train concept. The trains with a combined upper and lower entrance are comfortably equipped with generous seat spacing and plenty of storage space. Furthermore, the double-decker individual wagons permit the extension and shortening of the block train and, consequently, an adjustment to fluctuating demand or future development. As a result, they can be utilised for the most diverse of operational applications in both regional and long-distance traffic. Model Exact scale 1:160 Illuminated passenger compartment Structure made of high-quality, impact-resistant plastic Metal bottom plate Lighting with white LEDs Illuminated destination indicator (analog permanently on, digitally switchable) Long-distance headlights (can only be used digitally with decoder) Perfectly replicated three-dimensional front Illuminated driver's cab (only with decoder) With interior fittings, incl. driver's cab NEM-standard close coupling Light change white/red, in the direction of travel
On order, shipped within 10-15 days
Prototype “IC 2” is the name for the DB Fernverkehr AG TWINDEXX Vario® trains introduced following the timetable change on 13 December 2015. Back in 2010, Bombardier Transportation received the first order for 27 five-part double-deck trains in combination with the BR 146.5 locomotives from a previously-concluded framework contract with DB AG for a total of 800 double-deck trains. An order was placed for a further 17 trains in March 2015. The TWINDEXX Vario® is a further development of the tried-and-trusted double-deck platform from Görlitz. The top speed of the trains is 160 km/h. The IC 2 gradually replaced all previous IC trains in the new long-distance traffic concept from DB Fernverkehr AG. After the timetable change, the first routes for these trains were Leipzig – Norddeich Mole, Dresden – Cologne and Koblenz – Norddeich Mole. Model Exactly scale 1:160 True-to-original length over buffer Structure made of high-quality, impact-resistant plastic Metal bottom plate Printed window frames In-plane assembled windows Illuminated destination indicator (digital) Lighting with warm white LEDs Long-distance headlights (digital) True-to-scale details Perfectly replicated three-dimensional front Finely engraved details Fine paintwork and painting Illuminated driver's cab With interior fittings, incl. driver's cab NEM-standard close coupling Light change white/red, in the direction of travel For digital operation, decoder are required for each individual vehicle - Middle Car: Order no. 0019695.01; Control Car: Order no. 0019695.02 (Operating the vehicle without decoder in digital mode can result in damage to the electronics)
On order, shipped within 10-15 days
Prototype “IC 2” is the name for the DB Fernverkehr AG TWINDEXX Vario® trains introduced following the timetable change on 13 December 2015. Back in 2010, Bombardier Transportation received the first order for 27 five-part double-deck trains in combination with the BR 146.5 locomotives from a previously-concluded framework contract with DB AG for a total of 800 double-deck trains. An order was placed for a further 17 trains in March 2015. The TWINDEXX Vario® is a further development of the tried-and-trusted double-deck platform from Görlitz. The top speed of the trains is 160 km/h. The IC 2 gradually replaced all previous IC trains in the new long-distance traffic concept from DB Fernverkehr AG. After the timetable change, the first routes for these trains were Leipzig – Norddeich Mole, Dresden – Cologne and Koblenz – Norddeich Mole. Model Exactly scale 1:160 True-to-original length over buffer Structure made of high-quality, impact-resistant plastic Metal bottom plate Printed window frames In-plane assembled windows Illuminated destination indicator (digital) Lighting with warm white LEDs True-to-scale details Finely engraved details Fine paintwork and painting NEM-standard close coupling For digital operation, decoder (order no. 0019695.01) are required for each individual vehicle (Operating the vehicle without decoder in digital mode can result in damage to the electronics)
On order, shipped within 10-15 days
Prototype “IC 2” is the name for the DB Fernverkehr AG TWINDEXX Vario® trains introduced following the timetable change on 13 December 2015. Back in 2010, Bombardier Transportation received the first order for 27 five-part double-deck trains in combination with the BR 146.5 locomotives from a previously-concluded framework contract with DB AG for a total of 800 double-deck trains. An order was placed for a further 17 trains in March 2015. The TWINDEXX Vario® is a further development of the tried-and-trusted double-deck platform from Görlitz. The top speed of the trains is 160 km/h. The IC 2 gradually replaced all previous IC trains in the new long-distance traffic concept from DB Fernverkehr AG. After the timetable change, the first routes for these trains were Leipzig – Norddeich Mole, Dresden – Cologne and Koblenz – Norddeich Mole. Model Exactly scale 1:160 True-to-original length over buffer Structure made of high-quality, impact-resistant plastic Metal bottom plate Printed window frames In-plane assembled windows Illuminated destination indicator (digital) Lighting with warm white LEDs True-to-scale details Finely engraved details Fine paintwork and painting NEM-standard close coupling For digital operation, decoder (order no. 0019695.01) are required for each individual vehicle (Operating the vehicle without decoder in digital mode can result in damage to the electronics)
On order, shipped within 10-15 days
Prototype For many years now, double-decker trains have successfully formed the backbone of regional traffic. Double-decker trains are the ideal solution, especially on routes with low platform lengths and a high volume of passengers. The tried-and-tested single-wagon concept of the TWINDEXX Vario double-decker fleet is now being supplemented with an electrical railcar. Bombardier Transportation will supply 16 Bombardier TWINDEXX Vario railcars with regional train equipment to Deutsche Bahn AG. The new four-part railcars from the "Do 2010" generation consist of 2 railcars and 2 middle wagons respectively. With the newly-developed driven TWINDEXX Vario railcar, it is now possible to utilise the trains as pure double-decker multiple unit trains. As a result, it is also possible to use this vehicle as an electric multiple unit train alongside the classic push-pull operation with an electric or diesel locomotive. This railcar can be combined with middle wagons and control cars depending upon the application and desired capacity. The central buffer coupling enables operation with double traction and, as a result, the implementation of a wing-train concept. The trains with a combined upper and lower entrance are comfortably equipped with generous seat spacing and plenty of storage space. Furthermore, the double-decker individual wagons permit the extension and shortening of the block train and, consequently, an adjustment to fluctuating demand or future development. As a result, they can be utilised for the most diverse of operational applications in both regional and long-distance traffic. Model Exact scale 1:160 Illuminated passenger compartment Structure made of high-quality, impact-resistant plastic Metal bottom plate Lighting with white LEDs Illuminated destination indicator (analog permanently on, digitally switchable) Long-distance headlights (can only be used digitally with decoder) Perfectly replicated three-dimensional front Illuminated driver's cab (only with decoder) With interior fittings, incl. driver's cab NEM-standard close coupling Light change white/red, in the direction of travel
On order, shipped within 10-15 days
Prototype For many years now, double-decker trains have successfully formed the backbone of regional traffic. Double-decker trains are the ideal solution, especially on routes with low platform lengths and a high volume of passengers. The tried-and-tested single-wagon concept of the TWINDEXX Vario double-decker fleet is now being supplemented with an electrical railcar. Bombardier Transportation will supply 16 Bombardier TWINDEXX Vario railcars with regional train equipment to Deutsche Bahn AG. The new four-part railcars from the "Do 2010" generation consist of 2 railcars and 2 middle wagons respectively. With the newly-developed driven TWINDEXX Vario railcar, it is now possible to utilise the trains as pure double-decker multiple unit trains. As a result, it is also possible to use this vehicle as an electric multiple unit train alongside the classic push-pull operation with an electric or diesel locomotive. This railcar can be combined with middle wagons and control cars depending upon the application and desired capacity. The central buffer coupling enables operation with double traction and, as a result, the implementation of a wing-train concept. The trains with a combined upper and lower entrance are comfortably equipped with generous seat spacing and plenty of storage space. Furthermore, the double-decker individual wagons permit the extension and shortening of the block train and, consequently, an adjustment to fluctuating demand or future development. As a result, they can be utilised for the most diverse of operational applications in both regional and long-distance traffic. Model Exact scale 1:160 Illuminated passenger compartment Structure made of high-quality, impact-resistant plastic Metal bottom plate Lighting with white LEDs Illuminated destination indicator (analog permanently on, digitally switchable) Long-distance headlights (can only be used digitally with decoder) Perfectly replicated three-dimensional front Illuminated driver's cab (only with decoder) With interior fittings, incl. driver's cab NEM-standard close coupling Light change white/red, in the direction of travel
On order, shipped within 10-15 days