Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Rolling Stock

Locomotives, multiple units, coaches and wagons, new and pre-owned, from Z to G, checked by modellers.
Filter products
H0 Freight Locomotive BR 44 DRG
Brawa 70038 Scale H0
H0 Freight Locomotive BR 44 DRG

Prototype The Deutsche Reichsbahn Gesellschaft’s (DRG) procurement process for standardised freight locomotives mirrored its earlier evaluations of the 01 and 02 series. According to the specification, the new locomotive had to be capable of hauling goods trains weighing up to 1,200 metric tons over low mountain ranges, with an axle pressure of 20 tons. The maximum speed was set at 70 km/h for the pre-series locomotives. In 1926, to determine the most economical design, orders were placed with various locomotive manufacturers for the construction of 10 locomotives each of the 43 (two-cylinder engine) and 44 (three-cylinder engine) series. In addition to allocating the locomotives to other railway depots, a direct comparison was made between the 43 and 44 at the Pressig-Rothenkirchen depot. The respective merits and shortcomings of both series were determined via tests on the Franconian Forest Railway. The comparison of the two series did not initially favour the more powerful 44 series – the increased economy offered by the two-cylinder type 43 locomotive won the day. However, as Germany emerged from the shadow of the Great Depression in the mid-1930s, calls for more powerful freight locomotives grew louder. The experience gained ten years earlier with the type 44 was still fresh in the memory. The type 44 013-065 locomotives were consequently developed as an intermediate series – in part based on the experience gained in steam engine construction since 1925. In 1938 (from 44 066), full series production finally began. By 1949, a total of 1989 type 44 locomotives had been built at various locomotive factories in Germany and abroad. The new models lived up to all expectations and henceforth became the backbone of the goods train fleet. Model Detailed and movable internal engine, with two crop axles AC version with latest pickup generation Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Standard shaft rear with link guide Illuminated driver's cab (Version Digital EXTRA) Fire flickering (Version Digital EXTRA) Sound decoder, either built in or as a retrofit option Smoke generator can be retrofitted Close coupling between locomotive and tender Perfectly replicated back boilerplate Drive in the tender Single axle bearing Many extra mounted parts True to original wagner smoke deflectors Tender 2'2' T32

Regular price: CHF 568.50

On order, shipped within 10-15 days

H0 Freight Locomotive BR 44 DRG
Brawa 70039 Scale H0
H0 Freight Locomotive BR 44 DRG

Prototype The Deutsche Reichsbahn Gesellschaft’s (DRG) procurement process for standardised freight locomotives mirrored its earlier evaluations of the 01 and 02 series. According to the specification, the new locomotive had to be capable of hauling goods trains weighing up to 1,200 metric tons over low mountain ranges, with an axle pressure of 20 tons. The maximum speed was set at 70 km/h for the pre-series locomotives. In 1926, to determine the most economical design, orders were placed with various locomotive manufacturers for the construction of 10 locomotives each of the 43 (two-cylinder engine) and 44 (three-cylinder engine) series. In addition to allocating the locomotives to other railway depots, a direct comparison was made between the 43 and 44 at the Pressig-Rothenkirchen depot. The respective merits and shortcomings of both series were determined via tests on the Franconian Forest Railway. The comparison of the two series did not initially favour the more powerful 44 series – the increased economy offered by the two-cylinder type 43 locomotive won the day. However, as Germany emerged from the shadow of the Great Depression in the mid-1930s, calls for more powerful freight locomotives grew louder. The experience gained ten years earlier with the type 44 was still fresh in the memory. The type 44 013-065 locomotives were consequently developed as an intermediate series – in part based on the experience gained in steam engine construction since 1925. In 1938 (from 44 066), full series production finally began. By 1949, a total of 1989 type 44 locomotives had been built at various locomotive factories in Germany and abroad. The new models lived up to all expectations and henceforth became the backbone of the goods train fleet. Model Detailed and movable internal engine, with two crop axles AC version with latest pickup generation Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Standard shaft rear with link guide Illuminated driver's cab (Version Digital EXTRA) Fire flickering (Version Digital EXTRA) Sound decoder, either built in or as a retrofit option Smoke generator can be retrofitted Close coupling between locomotive and tender Perfectly replicated back boilerplate Drive in the tender Single axle bearing Many extra mounted parts True to original wagner smoke deflectors Tender 2'2' T32

Regular price: CHF 568.50

On order, shipped within 10-15 days

H0 Freight Locomotive BR 44 DR
Brawa 70048 Scale H0
H0 Freight Locomotive BR 44 DR

Prototype The Deutsche Reichsbahn Gesellschaft’s (DRG) procurement process for standardised freight locomotives mirrored its earlier evaluations of the 01 and 02 series. According to the specification, the new locomotive had to be capable of hauling goods trains weighing up to 1,200 metric tons over low mountain ranges, with an axle pressure of 20 tons. The maximum speed was set at 70 km/h for the pre-series locomotives. In 1926, to determine the most economical design, orders were placed with various locomotive manufacturers for the construction of 10 locomotives each of the 43 (two-cylinder engine) and 44 (three-cylinder engine) series. In addition to allocating the locomotives to other railway depots, a direct comparison was made between the 43 and 44 at the Pressig-Rothenkirchen depot. The respective merits and shortcomings of both series were determined via tests on the Franconian Forest Railway. The comparison of the two series did not initially favour the more powerful 44 series – the increased economy offered by the two-cylinder type 43 locomotive won the day. However, as Germany emerged from the shadow of the Great Depression in the mid-1930s, calls for more powerful freight locomotives grew louder. The experience gained ten years earlier with the type 44 was still fresh in the memory. The type 44 013-065 locomotives were consequently developed as an intermediate series – in part based on the experience gained in steam engine construction since 1925. In 1938 (from 44 066), full series production finally began. By 1949, a total of 1989 type 44 locomotives had been built at various locomotive factories in Germany and abroad. The new models lived up to all expectations and henceforth became the backbone of the goods train fleet. Model Detailed and movable internal engine, with two crop axles Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Standard shaft rear with link guide Illuminated driver's cab (Version Digital EXTRA) Fire flickering (Version Digital EXTRA) Sound decoder, either built in or as a retrofit option Smoke generator can be retrofitted Close coupling between locomotive and tender Perfectly replicated back boilerplate Drive in the tender Single axle bearing Many extra mounted parts True to original witte smoke deflectors Tender 2'2' T34

Regular price: CHF 451.15

On order, shipped within 10-15 days

H0 Freight Locomotive BR 44 DR
Brawa 70050 Scale H0
H0 Freight Locomotive BR 44 DR

Prototype The Deutsche Reichsbahn Gesellschaft’s (DRG) procurement process for standardised freight locomotives mirrored its earlier evaluations of the 01 and 02 series. According to the specification, the new locomotive had to be capable of hauling goods trains weighing up to 1,200 metric tons over low mountain ranges, with an axle pressure of 20 tons. The maximum speed was set at 70 km/h for the pre-series locomotives. In 1926, to determine the most economical design, orders were placed with various locomotive manufacturers for the construction of 10 locomotives each of the 43 (two-cylinder engine) and 44 (three-cylinder engine) series. In addition to allocating the locomotives to other railway depots, a direct comparison was made between the 43 and 44 at the Pressig-Rothenkirchen depot. The respective merits and shortcomings of both series were determined via tests on the Franconian Forest Railway. The comparison of the two series did not initially favour the more powerful 44 series – the increased economy offered by the two-cylinder type 43 locomotive won the day. However, as Germany emerged from the shadow of the Great Depression in the mid-1930s, calls for more powerful freight locomotives grew louder. The experience gained ten years earlier with the type 44 was still fresh in the memory. The type 44 013-065 locomotives were consequently developed as an intermediate series – in part based on the experience gained in steam engine construction since 1925. In 1938 (from 44 066), full series production finally began. By 1949, a total of 1989 type 44 locomotives had been built at various locomotive factories in Germany and abroad. The new models lived up to all expectations and henceforth became the backbone of the goods train fleet. Model Detailed and movable internal engine, with two crop axles Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Standard shaft rear with link guide Illuminated driver's cab (Version Digital EXTRA) Fire flickering (Version Digital EXTRA) Sound decoder, either built in or as a retrofit option Smoke generator can be retrofitted Close coupling between locomotive and tender Perfectly replicated back boilerplate Drive in the tender Single axle bearing Many extra mounted parts True to original witte smoke deflectors Tender 2'2' T34

Regular price: CHF 568.50

On order, shipped within 10-15 days

H0 Diesel Locomotive BR 211 SETG
Brawa 70052 Scale H0
H0 Diesel Locomotive BR 211 SETG

Etched cooler grille and fan grille Free-standing handrails Spring buffers Clear view through the driver's cabin Realistic reproduction of the tubular frame bogies incl. axle drive Reproduction of brake rods All specific details of the different series taken into consideration Completely recreated driver's cab Zinc die-cast chassis and gear housing Lights fitted with maintenance-free LEDs Digital EXTRA: complete with the following features that can be digitally controlled: sound, automatic decoupling, driver's cabin lighting, driven fans, shunting light and red light can be individually controlled It is possible to retrospectively convert the V 100 from analogue to digital via a PluX22 interface (only sound functions). Please note that it is not possible to retrospectively convert the digital remotecontrol coupling, the driven fan or the additional light functions.

Regular price: CHF 234.55

On order, shipped within 10-15 days

H0 Diesel Locomotive BR 211 SETG
Brawa 70054 Scale H0
H0 Diesel Locomotive BR 211 SETG

Etched cooler grille and fan grille Free-standing handrails Spring buffers Clear view through the driver's cabin Realistic reproduction of the tubular frame bogies incl. axle drive Reproduction of brake rods All specific details of the different series taken into consideration Completely recreated driver's cab Zinc die-cast chassis and gear housing Lights fitted with maintenance-free LEDs Digital EXTRA: complete with the following features that can be digitally controlled: sound, automatic decoupling, driver's cabin lighting, driven fans, shunting light and red light can be individually controlled It is possible to retrospectively convert the V 100 from analogue to digital via a PluX22 interface (only sound functions). Please note that it is not possible to retrospectively convert the digital remotecontrol coupling, the driven fan or the additional light functions.

Regular price: CHF 451.15

On order, shipped within 10-15 days

H0 Diesel Locomotive BR 212 DB
Brawa 70058 Scale H0
H0 Diesel Locomotive BR 212 DB

Etched cooler grille and fan grille Free-standing handrails Spring buffers Clear view through the driver's cabin Realistic reproduction of the tubular frame bogies incl. axle drive Reproduction of brake rods All specific details of the different series taken into consideration Completely recreated driver's cab Zinc die-cast chassis and gear housing Lights fitted with maintenance-free LEDs Digital EXTRA: complete with the following features that can be digitally controlled: sound, automatic decoupling, driver's cabin lighting, driven fans, shunting light and red light can be individually controlled It is possible to retrospectively convert the V 100 from analogue to digital via a PluX22 interface (only sound functions). Please note that it is not possible to retrospectively convert the digital remotecontrol coupling, the driven fan or the additional light functions.

Regular price: CHF 451.15

On order, shipped within 10-15 days

H0 Diesel Locomotive BR 212 DB
Brawa 70059 Scale H0
H0 Diesel Locomotive BR 212 DB

Etched cooler grille and fan grille Free-standing handrails Spring buffers Clear view through the driver's cabin Realistic reproduction of the tubular frame bogies incl. axle drive Reproduction of brake rods All specific details of the different series taken into consideration Completely recreated driver's cab Zinc die-cast chassis and gear housing Lights fitted with maintenance-free LEDs Digital EXTRA: complete with the following features that can be digitally controlled: sound, automatic decoupling, driver's cabin lighting, driven fans, shunting light and red light can be individually controlled It is possible to retrospectively convert the V 100 from analogue to digital via a PluX22 interface (only sound functions). Please note that it is not possible to retrospectively convert the digital remotecontrol coupling, the driven fan or the additional light functions.

Regular price: CHF 451.15

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 01 DB
Brawa 70060 Scale H0
H0 Express Train Locomotive BR 01 DB

Prototype From 1958, the German Federal Railway (Deutsche Bundesbahn) equipped 50 locomotives of the 01 series with the so-called Type I high-performance boiler. Designed according to the construction principles developed by Friedrich Witte, this boiler type had previously been successfully installed in the Bundesbahn’s series BR 01.10 locomotives. The new, fully welded boiler had a significantly better ratio of radiant to tubular heating surface (1:8.8 compared to 1:13.54 in the old-style boiler), which was mainly due to the built-in combustion chamber. To put this in figures: while the evaporation surface of the high-efficiency boiler was 54 m² smaller than that of its predecessor, this was compensated for by an 18 kg/m²h increase in the heating surface load. This made it possible to achieve the same boiler output with significantly lower fuel consumption. Visually, the conversion to the high-performance boiler resulted in locomotives that looked far neater and more modern. In addition, some adjustments were made with regard to occupational health and safety. The pipework was routed in cleaner lines. The sandbox was removed from the top of the boiler. The running board was replaced by a wide circulating plate and handles were integrated into the wind deflectors. On the technical side, the Knorr surface preheater was replaced by a type 57 mixing preheater. The locomotives 01 217 and 223 were fitted with experimental roller bearings in the driving and coupling rods, similar to those used in the BR 01.10. In operational terms, the new locomotives were deployed alongside the “old-style boiler” locomotives from traditional maintenance depots. The use of both 01 variants by DB only came to an end when steam locomotive maintenance finally ceased at the Hof railway depot in 1973. Model Impact resistant body and chassis Perforated underframe in die-cast zinc Die-cast zinc spoked wheels Fine metal drive and coupling rods True to era lighting Drive in the tender for optimal driving characteristics Close coupling between locomotive and tender Standard shaft rear with link guide True to original boiler rear wall Metal axle bearing True to scale axle base New sound

Regular price: CHF 433.10

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 001 DB
Brawa 70064 Scale H0
H0 Express Train Locomotive BR 001 DB

Prototype From 1958, the German Federal Railway (Deutsche Bundesbahn) equipped 50 locomotives of the 01 series with the so-called Type I high-performance boiler. Designed according to the construction principles developed by Friedrich Witte, this boiler type had previously been successfully installed in the Bundesbahn’s series BR 01.10 locomotives. The new, fully welded boiler had a significantly better ratio of radiant to tubular heating surface (1:8.8 compared to 1:13.54 in the old-style boiler), which was mainly due to the built-in combustion chamber. To put this in figures: while the evaporation surface of the high-efficiency boiler was 54 m² smaller than that of its predecessor, this was compensated for by an 18 kg/m²h increase in the heating surface load. This made it possible to achieve the same boiler output with significantly lower fuel consumption. Visually, the conversion to the high-performance boiler resulted in locomotives that looked far neater and more modern. In addition, some adjustments were made with regard to occupational health and safety. The pipework was routed in cleaner lines. The sandbox was removed from the top of the boiler. The running board was replaced by a wide circulating plate and handles were integrated into the wind deflectors. On the technical side, the Knorr surface preheater was replaced by a type 57 mixing preheater. The locomotives 01 217 and 223 were fitted with experimental roller bearings in the driving and coupling rods, similar to those used in the BR 01.10. In operational terms, the new locomotives were deployed alongside the “old-style boiler” locomotives from traditional maintenance depots. The use of both 01 variants by DB only came to an end when steam locomotive maintenance finally ceased at the Hof railway depot in 1973. Model Impact resistant body and chassis Perforated underframe in die-cast zinc Die-cast zinc spoked wheels Fine metal drive and coupling rods True to era lighting Drive in the tender for optimal driving characteristics Close coupling between locomotive and tender Standard shaft rear with link guide True to original boiler rear wall Metal axle bearing True to scale axle base New sound

Regular price: CHF 433.10

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 001 DB, Museum Locomotive: BEM – Bayrisches Eisenbahnmuseum e.V.
Brawa 70068 Scale H0
H0 Express Train Locomotive BR 001 DB, Museum Locomotive: BEM – Bayrisches Eisenbahnmuseum e.V.

Prototype From 1958, the German Federal Railway (Deutsche Bundesbahn) equipped 50 locomotives of the 01 series with the so-called Type I high-performance boiler. Designed according to the construction principles developed by Friedrich Witte, this boiler type had previously been successfully installed in the Bundesbahn’s series BR 01.10 locomotives. The new, fully welded boiler had a significantly better ratio of radiant to tubular heating surface (1:8.8 compared to 1:13.54 in the old-style boiler), which was mainly due to the built-in combustion chamber. To put this in figures: while the evaporation surface of the high-efficiency boiler was 54 m² smaller than that of its predecessor, this was compensated for by an 18 kg/m²h increase in the heating surface load. This made it possible to achieve the same boiler output with significantly lower fuel consumption. Visually, the conversion to the high-performance boiler resulted in locomotives that looked far neater and more modern. In addition, some adjustments were made with regard to occupational health and safety. The pipework was routed in cleaner lines. The sandbox was removed from the top of the boiler. The running board was replaced by a wide circulating plate and handles were integrated into the wind deflectors. On the technical side, the Knorr surface preheater was replaced by a type 57 mixing preheater. The locomotives 01 217 and 223 were fitted with experimental roller bearings in the driving and coupling rods, similar to those used in the BR 01.10. In operational terms, the new locomotives were deployed alongside the “old-style boiler” locomotives from traditional maintenance depots. The use of both 01 variants by DB only came to an end when steam locomotive maintenance finally ceased at the Hof railway depot in 1973. Model Impact resistant body and chassis Perforated underframe in die-cast zinc Die-cast zinc spoked wheels Fine metal drive and coupling rods True to era lighting Drive in the tender for optimal driving characteristics Close coupling between locomotive and tender Standard shaft rear with link guide True to original boiler rear wall Metal axle bearing True to scale axle base New sound

Regular price: CHF 433.10

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 001 DB, Museum Locomotive: BEM – Bayrisches Eisenbahnmuseum e.V.
Brawa 70071 Scale H0
H0 Express Train Locomotive BR 001 DB, Museum Locomotive: BEM – Bayrisches Eisenbahnmuseum e.V.

Prototype From 1958, the German Federal Railway (Deutsche Bundesbahn) equipped 50 locomotives of the 01 series with the so-called Type I high-performance boiler. Designed according to the construction principles developed by Friedrich Witte, this boiler type had previously been successfully installed in the Bundesbahn’s series BR 01.10 locomotives. The new, fully welded boiler had a significantly better ratio of radiant to tubular heating surface (1:8.8 compared to 1:13.54 in the old-style boiler), which was mainly due to the built-in combustion chamber. To put this in figures: while the evaporation surface of the high-efficiency boiler was 54 m² smaller than that of its predecessor, this was compensated for by an 18 kg/m²h increase in the heating surface load. This made it possible to achieve the same boiler output with significantly lower fuel consumption. Visually, the conversion to the high-performance boiler resulted in locomotives that looked far neater and more modern. In addition, some adjustments were made with regard to occupational health and safety. The pipework was routed in cleaner lines. The sandbox was removed from the top of the boiler. The running board was replaced by a wide circulating plate and handles were integrated into the wind deflectors. On the technical side, the Knorr surface preheater was replaced by a type 57 mixing preheater. The locomotives 01 217 and 223 were fitted with experimental roller bearings in the driving and coupling rods, similar to those used in the BR 01.10. In operational terms, the new locomotives were deployed alongside the “old-style boiler” locomotives from traditional maintenance depots. The use of both 01 variants by DB only came to an end when steam locomotive maintenance finally ceased at the Hof railway depot in 1973. Model Impact resistant body and chassis Perforated underframe in die-cast zinc Die-cast zinc spoked wheels Fine metal drive and coupling rods True to era lighting Drive in the tender for optimal driving characteristics Close coupling between locomotive and tender Standard shaft rear with link guide True to original boiler rear wall Metal axle bearing True to scale axle base New sound

Regular price: CHF 568.50

On order, lead time to be confirmed

H0 Express Train Locomotive BR 01 DB
Brawa 70088 Scale H0
H0 Express Train Locomotive BR 01 DB

Prototype Before the class BR 01 gained its reputation as “the” German express locomotive, the companies Borsig (01 001-008) and AEG (01 009-010) delivered a total of 10 pre-series locomotives to the Deutsche Reichsbahn Gesellschaft (DRG). The first model was the 01 008, which is still preserved today and was handed over to the DRG on 10 January 1926. However, these locomotives were ahead of their time, as many lines and railway depots were not yet prepared for an axle load of 20 t. As a result, the operating distances remained severely limited in the first few years of use. This in turn made the testing phase for the new locomotives an extremely drawn-out process. The most striking difference to the later series locomotives was the visibly longer cab, which remained a feature of the first ten 01’s. There were also differences in the design of the frame and many other details. Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 433.10

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 01 DB
Brawa 70090 Scale H0
H0 Express Train Locomotive BR 01 DB

Prototype Before the class BR 01 gained its reputation as “the” German express locomotive, the companies Borsig (01 001-008) and AEG (01 009-010) delivered a total of 10 pre-series locomotives to the Deutsche Reichsbahn Gesellschaft (DRG). The first model was the 01 008, which is still preserved today and was handed over to the DRG on 10 January 1926. However, these locomotives were ahead of their time, as many lines and railway depots were not yet prepared for an axle load of 20 t. As a result, the operating distances remained severely limited in the first few years of use. This in turn made the testing phase for the new locomotives an extremely drawn-out process. The most striking difference to the later series locomotives was the visibly longer cab, which remained a feature of the first ten 01’s. There were also differences in the design of the frame and many other details. Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 568.50

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 01 DB
Brawa 70091 Scale H0
H0 Express Train Locomotive BR 01 DB

Prototype Before the class BR 01 gained its reputation as “the” German express locomotive, the companies Borsig (01 001-008) and AEG (01 009-010) delivered a total of 10 pre-series locomotives to the Deutsche Reichsbahn Gesellschaft (DRG). The first model was the 01 008, which is still preserved today and was handed over to the DRG on 10 January 1926. However, these locomotives were ahead of their time, as many lines and railway depots were not yet prepared for an axle load of 20 t. As a result, the operating distances remained severely limited in the first few years of use. This in turn made the testing phase for the new locomotives an extremely drawn-out process. The most striking difference to the later series locomotives was the visibly longer cab, which remained a feature of the first ten 01’s. There were also differences in the design of the frame and many other details. Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 568.50

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 02 DRG
Brawa 70092 Scale H0
H0 Express Train Locomotive BR 02 DRG

Prototype Before the class BR 01 gained its reputation as “the” German express locomotive, the companies Borsig (01 001-008) and AEG (01 009-010) delivered a total of 10 pre-series locomotives to the Deutsche Reichsbahn Gesellschaft (DRG). The first model was the 01 008, which is still preserved today and was handed over to the DRG on 10 January 1926. However, these locomotives were ahead of their time, as many lines and railway depots were not yet prepared for an axle load of 20 t. As a result, the operating distances remained severely limited in the first few years of use. This in turn made the testing phase for the new locomotives an extremely drawn-out process. The most striking difference to the later series locomotives was the visibly longer cab, which remained a feature of the first ten 01’s. There were also differences in the design of the frame and many other details. Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 433.10

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 02 DRG
Brawa 70094 Scale H0
H0 Express Train Locomotive BR 02 DRG

Prototype Before the class BR 01 gained its reputation as “the” German express locomotive, the companies Borsig (01 001-008) and AEG (01 009-010) delivered a total of 10 pre-series locomotives to the Deutsche Reichsbahn Gesellschaft (DRG). The first model was the 01 008, which is still preserved today and was handed over to the DRG on 10 January 1926. However, these locomotives were ahead of their time, as many lines and railway depots were not yet prepared for an axle load of 20 t. As a result, the operating distances remained severely limited in the first few years of use. This in turn made the testing phase for the new locomotives an extremely drawn-out process. The most striking difference to the later series locomotives was the visibly longer cab, which remained a feature of the first ten 01’s. There were also differences in the design of the frame and many other details. Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 568.50

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 02 DRG
Brawa 70095 Scale H0
H0 Express Train Locomotive BR 02 DRG

Prototype Before the class BR 01 gained its reputation as “the” German express locomotive, the companies Borsig (01 001-008) and AEG (01 009-010) delivered a total of 10 pre-series locomotives to the Deutsche Reichsbahn Gesellschaft (DRG). The first model was the 01 008, which is still preserved today and was handed over to the DRG on 10 January 1926. However, these locomotives were ahead of their time, as many lines and railway depots were not yet prepared for an axle load of 20 t. As a result, the operating distances remained severely limited in the first few years of use. This in turn made the testing phase for the new locomotives an extremely drawn-out process. The most striking difference to the later series locomotives was the visibly longer cab, which remained a feature of the first ten 01’s. There were also differences in the design of the frame and many other details. Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 568.50

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 02 DRG
Brawa 70096 Scale H0
H0 Express Train Locomotive BR 02 DRG

Prototype Before the class BR 01 gained its reputation as “the” German express locomotive, the companies Borsig (01 001-008) and AEG (01 009-010) delivered a total of 10 pre-series locomotives to the Deutsche Reichsbahn Gesellschaft (DRG). The first model was the 01 008, which is still preserved today and was handed over to the DRG on 10 January 1926. However, these locomotives were ahead of their time, as many lines and railway depots were not yet prepared for an axle load of 20 t. As a result, the operating distances remained severely limited in the first few years of use. This in turn made the testing phase for the new locomotives an extremely drawn-out process. The most striking difference to the later series locomotives was the visibly longer cab, which remained a feature of the first ten 01’s. There were also differences in the design of the frame and many other details. Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 433.10

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 02 DRG
Brawa 70098 Scale H0
H0 Express Train Locomotive BR 02 DRG

Prototype Before the class BR 01 gained its reputation as “the” German express locomotive, the companies Borsig (01 001-008) and AEG (01 009-010) delivered a total of 10 pre-series locomotives to the Deutsche Reichsbahn Gesellschaft (DRG). The first model was the 01 008, which is still preserved today and was handed over to the DRG on 10 January 1926. However, these locomotives were ahead of their time, as many lines and railway depots were not yet prepared for an axle load of 20 t. As a result, the operating distances remained severely limited in the first few years of use. This in turn made the testing phase for the new locomotives an extremely drawn-out process. The most striking difference to the later series locomotives was the visibly longer cab, which remained a feature of the first ten 01’s. There were also differences in the design of the frame and many other details. Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 568.50

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 02 DRG
Brawa 70099 Scale H0
H0 Express Train Locomotive BR 02 DRG

Prototype Before the class BR 01 gained its reputation as “the” German express locomotive, the companies Borsig (01 001-008) and AEG (01 009-010) delivered a total of 10 pre-series locomotives to the Deutsche Reichsbahn Gesellschaft (DRG). The first model was the 01 008, which is still preserved today and was handed over to the DRG on 10 January 1926. However, these locomotives were ahead of their time, as many lines and railway depots were not yet prepared for an axle load of 20 t. As a result, the operating distances remained severely limited in the first few years of use. This in turn made the testing phase for the new locomotives an extremely drawn-out process. The most striking difference to the later series locomotives was the visibly longer cab, which remained a feature of the first ten 01’s. There were also differences in the design of the frame and many other details. Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 568.50

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 01 DB
Brawa 70100 Scale H0
H0 Express Train Locomotive BR 01 DB

Prototype Celebrate 100 years of the iconic BR 01 express locomotive with us! To mark this special occasion, we are proud to present a faithful recreation of the legendary E 230 train formation, which carried passengers from Dortmund to Cologne in the latter half of the 1950s. The E 230 was the quintessential example of a post-war express train, composed of six pre-war express train coaches paired with modern “yl” city express coaches. All the passenger coaches came from the inventory of Dortmund Hauptbahnhof, showcasing the diverse fleets operated by the railway companies of that era. The train’s locomotive, by contrast, originated from the Cologne Betriebsbahnhof railway depot. The BR 01 or BR 03 were commonly used on this route, including the renowned 01 100, which has been faithfully recreated in our model. With its powerful build and striking appearance, the BR 01 defined the look of the express train services of its time. On its northern route, the E 230 express train carried passengers through the Ruhr region: Dortmund Hauptbahnhof – Rauxel – Herne – Wanne-Eickel – Gelsenkirchen – Essen-Altenessen – Oberhausen – Duisburg – Düsseldorf. This train reached its final destination in the late afternoon: Cologne Hauptbahnhof. Evoke the spirit of the 1950s with the BRAWA Express Train Locomotive BR 01 and its matching passenger coaches – customisable to your preferences for an authentic and nostalgic addition to your model railway layout! Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 433.10

On order, shipped within 10-15 days

H0 Express Train Locomotive BR 01 DB
Brawa 70102 Scale H0
H0 Express Train Locomotive BR 01 DB

Prototype Celebrate 100 years of the iconic BR 01 express locomotive with us! To mark this special occasion, we are proud to present a faithful recreation of the legendary E 230 train formation, which carried passengers from Dortmund to Cologne in the latter half of the 1950s. The E 230 was the quintessential example of a post-war express train, composed of six pre-war express train coaches paired with modern “yl” city express coaches. All the passenger coaches came from the inventory of Dortmund Hauptbahnhof, showcasing the diverse fleets operated by the railway companies of that era. The train’s locomotive, by contrast, originated from the Cologne Betriebsbahnhof railway depot. The BR 01 or BR 03 were commonly used on this route, including the renowned 01 100, which has been faithfully recreated in our model. With its powerful build and striking appearance, the BR 01 defined the look of the express train services of its time. On its northern route, the E 230 express train carried passengers through the Ruhr region: Dortmund Hauptbahnhof – Rauxel – Herne – Wanne-Eickel – Gelsenkirchen – Essen-Altenessen – Oberhausen – Duisburg – Düsseldorf. This train reached its final destination in the late afternoon: Cologne Hauptbahnhof. Evoke the spirit of the 1950s with the BRAWA Express Train Locomotive BR 01 and its matching passenger coaches – customisable to your preferences for an authentic and nostalgic addition to your model railway layout! Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 568.50

On order, lead time to be confirmed

H0 Express Train Locomotive BR 01 DB
Brawa 70103 Scale H0
H0 Express Train Locomotive BR 01 DB

Prototype Celebrate 100 years of the iconic BR 01 express locomotive with us! To mark this special occasion, we are proud to present a faithful recreation of the legendary E 230 train formation, which carried passengers from Dortmund to Cologne in the latter half of the 1950s. The E 230 was the quintessential example of a post-war express train, composed of six pre-war express train coaches paired with modern “yl” city express coaches. All the passenger coaches came from the inventory of Dortmund Hauptbahnhof, showcasing the diverse fleets operated by the railway companies of that era. The train’s locomotive, by contrast, originated from the Cologne Betriebsbahnhof railway depot. The BR 01 or BR 03 were commonly used on this route, including the renowned 01 100, which has been faithfully recreated in our model. With its powerful build and striking appearance, the BR 01 defined the look of the express train services of its time. On its northern route, the E 230 express train carried passengers through the Ruhr region: Dortmund Hauptbahnhof – Rauxel – Herne – Wanne-Eickel – Gelsenkirchen – Essen-Altenessen – Oberhausen – Duisburg – Düsseldorf. This train reached its final destination in the late afternoon: Cologne Hauptbahnhof. Evoke the spirit of the 1950s with the BRAWA Express Train Locomotive BR 01 and its matching passenger coaches – customisable to your preferences for an authentic and nostalgic addition to your model railway layout! Model Boiler, driver's cab and tender made of high-quality, impact-resistant plastic Perforated underframe and spoked wheels in die-cast zinc Sound decoder, either built in or as a retrofit option Illuminated driver's cab True-to epoch lighting, multipart lamp housing Standard shaft rear with link guide Close coupling between locomotive and tender Perfectly replicated back boilerplate Extra mounted steps Navigable minimum radius: The models of BR 01 are technically suitable for R 360. For best driving characteristics we recommend the use on R 420.

Regular price: CHF 568.50

On order, lead time to be confirmed