Freight Wagons
Prototype In order to achieve a larger loading space of 40 m3, the undercarriage and the wheel base of the previous Otmm wagons were extended by 500 mm. The first of these wagons with a capacity of 40 m3 was built by the Paderborn railway repair shop on a trial basis in 1961. The design stood the test, and so the railway repair shops of Kaiserslautern and Weiden built more than 16,000 Otmm 70/Ed 090 wagons between 1961 and 1970, also using profiles of old but usable Omm 37 wagons. The wagons - referred to as Fc 090 from 1980 onwards - ran as single wagons and in block trains with bulk goods of all kinds. A shortage of hinged roof wagons led to the fact that they were also covered with tarpaulins and used for the transport of cereals. Consequently, 1,500 wagons were equipped with hinged roofs in 1978/79 and referred to as Tdgs-z 932. Many other wagons received a load alteration switchover and were referred to as Fcs 090 or, after being adapted for further operation from 1991 onwards, as Fcs 092. In 1994, the DB AG took over even more than 8,500 Fc(s) 090 wagons which were decommissioned until 2007. In 2012, around 2,600 of the Fcs 092 wagons were still in service, another 786 wagons were used as Fcs-x 092 in coal transport. Model Metal axle holders Bogie with three-point support Individually mounted brake system Brake blocks in wheel plane Many separately mounted parts Individually mounted axle box cover Free standing ladders Individually mounted railing Replica of the supports in the funnel
On order, shipped within 10-15 days
Prototype In order to achieve a larger loading space of 40 m3, the undercarriage and the wheel base of the previous Otmm wagons were extended by 500 mm. The first of these wagons with a capacity of 40 m3 was built by the Paderborn railway repair shop on a trial basis in 1961. The design stood the test, and so the railway repair shops of Kaiserslautern and Weiden built more than 16,000 Otmm 70/Ed 090 wagons between 1961 and 1970, also using profiles of old but usable Omm 37 wagons. The wagons - referred to as Fc 090 from 1980 onwards - ran as single wagons and in block trains with bulk goods of all kinds. A shortage of hinged roof wagons led to the fact that they were also covered with tarpaulins and used for the transport of cereals. Consequently, 1,500 wagons were equipped with hinged roofs in 1978/79 and referred to as Tdgs-z 932. Many other wagons received a load alteration switchover and were referred to as Fcs 090 or, after being adapted for further operation from 1991 onwards, as Fcs 092. In 1994, the DB AG took over even more than 8,500 Fc(s) 090 wagons which were decommissioned until 2007. In 2012, around 2,600 of the Fcs 092 wagons were still in service, another 786 wagons were used as Fcs-x 092 in coal transport. Model Metal axle holders Bogie with three-point support Individually mounted brake system Brake blocks in wheel plane Many separately mounted parts Individually mounted axle box cover Free standing ladders Individually mounted railing Replica of the supports in the funnel
On order, shipped within 10-15 days
Prototype In order to achieve a larger loading space of 40 m3, the undercarriage and the wheel base of the previous Otmm wagons were extended by 500 mm. The first of these wagons with a capacity of 40 m3 was built by the Paderborn railway repair shop on a trial basis in 1961. The design stood the test, and so the railway repair shops of Kaiserslautern and Weiden built more than 16,000 Otmm 70/Ed 090 wagons between 1961 and 1970, also using profiles of old but usable Omm 37 wagons. The wagons - referred to as Fc 090 from 1980 onwards - ran as single wagons and in block trains with bulk goods of all kinds. A shortage of hinged roof wagons led to the fact that they were also covered with tarpaulins and used for the transport of cereals. Consequently, 1,500 wagons were equipped with hinged roofs in 1978/79 and referred to as Tdgs-z 932. Many other wagons received a load alteration switchover and were referred to as Fcs 090 or, after being adapted for further operation from 1991 onwards, as Fcs 092. In 1994, the DB AG took over even more than 8,500 Fc(s) 090 wagons which were decommissioned until 2007. In 2012, around 2,600 of the Fcs 092 wagons were still in service, another 786 wagons were used as Fcs-x 092 in coal transport. Model Metal axle holders Bogie with three-point support Individually mounted brake system Brake blocks in wheel plane Many separately mounted parts Individually mounted axle box cover Free standing ladders Individually mounted railing Replica of the supports in the funnel
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Bogie with three-point support Individually mounted wheelchocks Individually mounted brake systems Metal wheels Finely engraved bogies brake shoes in wheel plane Individually mounted axle brake rod
On order, shipped within 10-15 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
On order, shipped within 10-15 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
On order, shipped within 10-15 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
On order, shipped within 10-15 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
On order, shipped within 10-15 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
On order, shipped within 10-15 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
On order, shipped within 10-15 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
On order, shipped within 10-15 days
Prototype Freight cars have always been required on the railways, now as in the past. The Deutsche Reichsbahn (DR) was able to provide a short-term remedy in the 1950s through retrofitting and modernisation, but it was clear that other solutions would have to be found in the long-term. As a result, in 1965 the Leipzig RAW “unit” designed a Glmms car which complied substantially with the standard characteristics of the UIC leaflet. The lessons learned from the test locomotives were incorporated in the series wagon produced from 1968, which was now known as Glmms 14.05 (later Gbs 1500). The design, with its distinctive corrugated side panels, came into being as a fully welded structure. The side panels were moved down onto the lower edge of the external bodysolebar and welded to the box profiles. This allowed for simplified side body supports. In order to prevent damage to the sheet metal walls during loading, the wagons were lined internally with wood. The floor consisted of standard pine planks and was suitable for loading with a forklift. Based on the Gbs 1500 design, of which over 1700 units were manufactured, a number of different versions were produced, including insulated boxcars, express goods wagons and vestibule cars. Since production capacity was almost exhausted at domestic facilities, wagons were also constructed in neighbouring countries and even Spain. Due to their RIV, MC and OPW transport suitability, the wagons could be used with relative freedom outside the DDR and were therefore often seen in Bundesbahn trains even before the fall of the Iron Curtain. However, until DB AG was founded, there were still as many as 7,000 wagons in use. Model Metal wheels Individually mounted signal holder Individually mounted axle box cover NEM-standard short-coupling Metal axle bearing Multi-part brake system Brake shoes in wheel plane True to original car bottom
On order, shipped within 10-15 days
Prototype Freight cars have always been required on the railways, now as in the past. The Deutsche Reichsbahn (DR) was able to provide a short-term remedy in the 1950s through retrofitting and modernisation, but it was clear that other solutions would have to be found in the long-term. As a result, in 1965 the Leipzig RAW “unit” designed a Glmms car which complied substantially with the standard characteristics of the UIC leaflet. The lessons learned from the test locomotives were incorporated in the series wagon produced from 1968, which was now known as Glmms 14.05 (later Gbs 1500). The design, with its distinctive corrugated side panels, came into being as a fully welded structure. The side panels were moved down onto the lower edge of the external bodysolebar and welded to the box profiles. This allowed for simplified side body supports. In order to prevent damage to the sheet metal walls during loading, the wagons were lined internally with wood. The floor consisted of standard pine planks and was suitable for loading with a forklift. Based on the Gbs 1500 design, of which over 1700 units were manufactured, a number of different versions were produced, including insulated boxcars, express goods wagons and vestibule cars. Since production capacity was almost exhausted at domestic facilities, wagons were also constructed in neighbouring countries and even Spain. Due to their RIV, MC and OPW transport suitability, the wagons could be used with relative freedom outside the DDR and were therefore often seen in Bundesbahn trains even before the fall of the Iron Curtain. However, until DB AG was founded, there were still as many as 7,000 wagons in use. Model Metal wheels Individually mounted signal holder Individually mounted axle box cover NEM-standard short-coupling Metal axle bearing Multi-part brake system Brake shoes in wheel plane True to original car bottom
On order, shipped within 10-15 days
Prototype Freight cars have always been required on the railways, now as in the past. The Deutsche Reichsbahn (DR) was able to provide a short-term remedy in the 1950s through retrofitting and modernisation, but it was clear that other solutions would have to be found in the long-term. As a result, in 1965 the Leipzig RAW “unit” designed a Glmms car which complied substantially with the standard characteristics of the UIC leaflet. The lessons learned from the test locomotives were incorporated in the series wagon produced from 1968, which was now known as Glmms 14.05 (later Gbs 1500). The design, with its distinctive corrugated side panels, came into being as a fully welded structure. The side panels were moved down onto the lower edge of the external bodysolebar and welded to the box profiles. This allowed for simplified side body supports. In order to prevent damage to the sheet metal walls during loading, the wagons were lined internally with wood. The floor consisted of standard pine planks and was suitable for loading with a forklift. Based on the Gbs 1500 design, of which over 1700 units were manufactured, a number of different versions were produced, including insulated boxcars, express goods wagons and vestibule cars. Since production capacity was almost exhausted at domestic facilities, wagons were also constructed in neighbouring countries and even Spain. Due to their RIV, MC and OPW transport suitability, the wagons could be used with relative freedom outside the DDR and were therefore often seen in Bundesbahn trains even before the fall of the Iron Curtain. However, until DB AG was founded, there were still as many as 7,000 wagons in use. Model Metal wheels Individually mounted signal holder Individually mounted axle box cover NEM-standard short-coupling Metal axle bearing Multi-part brake system Brake shoes in wheel plane True to original car bottom
On order, shipped within 10-15 days
Prototype Freight cars have always been required on the railways, now as in the past. The Deutsche Reichsbahn (DR) was able to provide a short-term remedy in the 1950s through retrofitting and modernisation, but it was clear that other solutions would have to be found in the long-term. As a result, in 1965 the Leipzig RAW “unit” designed a Glmms car which complied substantially with the standard characteristics of the UIC leaflet. The lessons learned from the test locomotives were incorporated in the series wagon produced from 1968, which was now known as Glmms 14.05 (later Gbs 1500). The design, with its distinctive corrugated side panels, came into being as a fully welded structure. The side panels were moved down onto the lower edge of the external bodysolebar and welded to the box profiles. This allowed for simplified side body supports. In order to prevent damage to the sheet metal walls during loading, the wagons were lined internally with wood. The floor consisted of standard pine planks and was suitable for loading with a forklift. Based on the Gbs 1500 design, of which over 1700 units were manufactured, a number of different versions were produced, including insulated boxcars, express goods wagons and vestibule cars. Since production capacity was almost exhausted at domestic facilities, wagons were also constructed in neighbouring countries and even Spain. Due to their RIV, MC and OPW transport suitability, the wagons could be used with relative freedom outside the DDR and were therefore often seen in Bundesbahn trains even before the fall of the Iron Curtain. However, until DB AG was founded, there were still as many as 7,000 wagons in use. Model Metal wheels Individually mounted signal holder Individually mounted axle box cover NEM-standard short-coupling Metal axle bearing Multi-part brake system Brake shoes in wheel plane True to original car bottom
On order, shipped within 10-15 days