Freight Wagons
Prototype Freight cars have always been required on the railways, now as in the past. The Deutsche Reichsbahn (DR) was able to provide a short-term remedy in the 1950s through retrofitting and modernisation, but it was clear that other solutions would have to be found in the long-term. As a result, in 1965 the Leipzig RAW “unit” designed a Glmms car which complied substantially with the standard characteristics of the UIC leaflet. The lessons learned from the test locomotives were incorporated in the series wagon produced from 1968, which was now known as Glmms 14.05 (later Gbs 1500). The design, with its distinctive corrugated side panels, came into being as a fully welded structure. The side panels were moved down onto the lower edge of the external bodysolebar and welded to the box profiles. This allowed for simplified side body supports. In order to prevent damage to the sheet metal walls during loading, the wagons were lined internally with wood. The floor consisted of standard pine planks and was suitable for loading with a forklift. Based on the Gbs 1500 design, of which over 1700 units were manufactured, a number of different versions were produced, including insulated boxcars, express goods wagons and vestibule cars. Since production capacity was almost exhausted at domestic facilities, wagons were also constructed in neighbouring countries and even Spain. Due to their RIV, MC and OPW transport suitability, the wagons could be used with relative freedom outside the DDR and were therefore often seen in Bundesbahn trains even before the fall of the Iron Curtain. However, until DB AG was founded, there were still as many as 7,000 wagons in use. Model Metal wheels Individually mounted signal holder Individually mounted axle box cover NEM-standard short-coupling Metal axle bearing Multi-part brake system Brake shoes in wheel plane True to original car bottom
On order, shipped within 10-15 days
Prototype Freight cars have always been required on the railways, now as in the past. The Deutsche Reichsbahn (DR) was able to provide a short-term remedy in the 1950s through retrofitting and modernisation, but it was clear that other solutions would have to be found in the long-term. As a result, in 1965 the Leipzig RAW “unit” designed a Glmms car which complied substantially with the standard characteristics of the UIC leaflet. The lessons learned from the test locomotives were incorporated in the series wagon produced from 1968, which was now known as Glmms 14.05 (later Gbs 1500). The design, with its distinctive corrugated side panels, came into being as a fully welded structure. The side panels were moved down onto the lower edge of the external bodysolebar and welded to the box profiles. This allowed for simplified side body supports. In order to prevent damage to the sheet metal walls during loading, the wagons were lined internally with wood. The floor consisted of standard pine planks and was suitable for loading with a forklift. Based on the Gbs 1500 design, of which over 1700 units were manufactured, a number of different versions were produced, including insulated boxcars, express goods wagons and vestibule cars. Since production capacity was almost exhausted at domestic facilities, wagons were also constructed in neighbouring countries and even Spain. Due to their RIV, MC and OPW transport suitability, the wagons could be used with relative freedom outside the DDR and were therefore often seen in Bundesbahn trains even before the fall of the Iron Curtain. However, until DB AG was founded, there were still as many as 7,000 wagons in use. Model Metal wheels Individually mounted signal holder Individually mounted axle box cover NEM-standard short-coupling Metal axle bearing Multi-part brake system Brake shoes in wheel plane True to original car bottom
On order, shipped within 10-15 days
Prototype Freight cars have always been required on the railways, now as in the past. The Deutsche Reichsbahn (DR) was able to provide a short-term remedy in the 1950s through retrofitting and modernisation, but it was clear that other solutions would have to be found in the long-term. As a result, in 1965 the Leipzig RAW “unit” designed a Glmms car which complied substantially with the standard characteristics of the UIC leaflet. The lessons learned from the test locomotives were incorporated in the series wagon produced from 1968, which was now known as Glmms 14.05 (later Gbs 1500). The design, with its distinctive corrugated side panels, came into being as a fully welded structure. The side panels were moved down onto the lower edge of the external bodysolebar and welded to the box profiles. This allowed for simplified side body supports. In order to prevent damage to the sheet metal walls during loading, the wagons were lined internally with wood. The floor consisted of standard pine planks and was suitable for loading with a forklift. Based on the Gbs 1500 design, of which over 1700 units were manufactured, a number of different versions were produced, including insulated boxcars, express goods wagons and vestibule cars. Since production capacity was almost exhausted at domestic facilities, wagons were also constructed in neighbouring countries and even Spain. Due to their RIV, MC and OPW transport suitability, the wagons could be used with relative freedom outside the DDR and were therefore often seen in Bundesbahn trains even before the fall of the Iron Curtain. However, until DB AG was founded, there were still as many as 7,000 wagons in use. Model Metal wheels Individually mounted signal holder Individually mounted axle box cover NEM-standard short-coupling Metal axle bearing Multi-part brake system Brake shoes in wheel plane True to original car bottom
On order, shipped within 10-15 days
Prototype Freight cars have always been required on the railways, now as in the past. The Deutsche Reichsbahn (DR) was able to provide a short-term remedy in the 1950s through retrofitting and modernisation, but it was clear that other solutions would have to be found in the long-term. As a result, in 1965 the Leipzig RAW “unit” designed a Glmms car which complied substantially with the standard characteristics of the UIC leaflet. The lessons learned from the test locomotives were incorporated in the series wagon produced from 1968, which was now known as Glmms 14.05 (later Gbs 1500). The design, with its distinctive corrugated side panels, came into being as a fully welded structure. The side panels were moved down onto the lower edge of the external bodysolebar and welded to the box profiles. This allowed for simplified side body supports. In order to prevent damage to the sheet metal walls during loading, the wagons were lined internally with wood. The floor consisted of standard pine planks and was suitable for loading with a forklift. Based on the Gbs 1500 design, of which over 1700 units were manufactured, a number of different versions were produced, including insulated boxcars, express goods wagons and vestibule cars. Since production capacity was almost exhausted at domestic facilities, wagons were also constructed in neighbouring countries and even Spain. Due to their RIV, MC and OPW transport suitability, the wagons could be used with relative freedom outside the DDR and were therefore often seen in Bundesbahn trains even before the fall of the Iron Curtain. However, until DB AG was founded, there were still as many as 7,000 wagons in use. Model Metal wheels Individually mounted signal holder Individually mounted axle box cover NEM-standard short-coupling Metal axle bearing Multi-part brake system Brake shoes in wheel plane True to original car bottom
On order, shipped within 10-15 days
Prototype Freight cars have always been required on the railways, now as in the past. The Deutsche Reichsbahn (DR) was able to provide a short-term remedy in the 1950s through retrofitting and modernisation, but it was clear that other solutions would have to be found in the long-term. As a result, in 1965 the Leipzig RAW “unit” designed a Glmms car which complied substantially with the standard characteristics of the UIC leaflet. The lessons learned from the test locomotives were incorporated in the series wagon produced from 1968, which was now known as Glmms 14.05 (later Gbs 1500). The design, with its distinctive corrugated side panels, came into being as a fully welded structure. The side panels were moved down onto the lower edge of the external bodysolebar and welded to the box profiles. This allowed for simplified side body supports. In order to prevent damage to the sheet metal walls during loading, the wagons were lined internally with wood. The floor consisted of standard pine planks and was suitable for loading with a forklift. Based on the Gbs 1500 design, of which over 1700 units were manufactured, a number of different versions were produced, including insulated boxcars, express goods wagons and vestibule cars. Since production capacity was almost exhausted at domestic facilities, wagons were also constructed in neighbouring countries and even Spain. Due to their RIV, MC and OPW transport suitability, the wagons could be used with relative freedom outside the DDR and were therefore often seen in Bundesbahn trains even before the fall of the Iron Curtain. However, until DB AG was founded, there were still as many as 7,000 wagons in use. Model Metal wheels Individually mounted signal holder Individually mounted axle box cover NEM-standard short-coupling Metal axle bearing Multi-part brake system Brake shoes in wheel plane True to original car bottom
On order, shipped within 10-15 days
Prototype 30m³ lightweight tank wagon in Uerdinger design – thanks to general technical advances in lightweight construction and welding technology, the management at the National Railway (Reichsbahn) decided to dispense with the actual vehicle frame when designing new tank wagons. Instead, the tensile and impact forces would, as far as possible, be absorbed by the boiler. Through the extensive use of welding technology, the goal was to reduce the raw-material requirements and manufacturing costs while at the same time obtaining more robust vehicles. For this reason, the wagon factory in Uerdingen received an order in 1938 to develop a lightweight tank car with a cargo volume of 30m³. As early as 1939, the three prototypes were handed over to two private goods-wagon rental companies as well as the state’s economic research association (Wirtschaftliche Forschungsgesellschaft (Wifo)) for testing. Following a small intermediate series in 1940, series production of the 30m³ Uerdinger-type lightweight tank wagon began in 1941. The largest customer was the German air force (Luftwaffe) with approx. 2,200 units, followed by the Wifo and many smaller companies, which resulted in a total of around 3,700 cars being built. In the post-war period, the wagons acquired by the Wifo and Luftwaffe were redistributed to other wagon operators in both German states. In the following decades, the wagons were primarily used by larger companies in the mineral oil industry, and also by smaller private companies as well as DB and DR themselves. Some of the wagons also remained abroad, where they were operated by new owners. In 2016 one of these wagons was still in use in internal interfactory traffic at Haltermann in Hamburg. Model Bogie with three-point support Individually mounted axle box cover Individually mounted wheelchocks Individually mounted brake systems Finely engraved bogies Brake blocks in wheel plane Individually mounted axle brake rod Free standing handle bars
On order, shipped within 10-15 days
Prototype 30m³ lightweight tank wagon in Uerdinger design – thanks to general technical advances in lightweight construction and welding technology, the management at the National Railway (Reichsbahn) decided to dispense with the actual vehicle frame when designing new tank wagons. Instead, the tensile and impact forces would, as far as possible, be absorbed by the boiler. Through the extensive use of welding technology, the goal was to reduce the raw-material requirements and manufacturing costs while at the same time obtaining more robust vehicles. For this reason, the wagon factory in Uerdingen received an order in 1938 to develop a lightweight tank car with a cargo volume of 30m³. As early as 1939, the three prototypes were handed over to two private goods-wagon rental companies as well as the state’s economic research association (Wirtschaftliche Forschungsgesellschaft (Wifo)) for testing. Following a small intermediate series in 1940, series production of the 30m³ Uerdinger-type lightweight tank wagon began in 1941. The largest customer was the German air force (Luftwaffe) with approx. 2,200 units, followed by the Wifo and many smaller companies, which resulted in a total of around 3,700 cars being built. In the post-war period, the wagons acquired by the Wifo and Luftwaffe were redistributed to other wagon operators in both German states. In the following decades, the wagons were primarily used by larger companies in the mineral oil industry, and also by smaller private companies as well as DB and DR themselves. Some of the wagons also remained abroad, where they were operated by new owners. In 2016 one of these wagons was still in use in internal interfactory traffic at Haltermann in Hamburg. Model Bogie with three-point support Individually mounted axle box cover Individually mounted wheelchocks Individually mounted brake systems Finely engraved bogies Brake blocks in wheel plane Individually mounted axle brake rod Free standing handle bars
On order, shipped within 10-15 days
Prototype 30m³ lightweight tank wagon in Uerdinger design – thanks to general technical advances in lightweight construction and welding technology, the management at the National Railway (Reichsbahn) decided to dispense with the actual vehicle frame when designing new tank wagons. Instead, the tensile and impact forces would, as far as possible, be absorbed by the boiler. Through the extensive use of welding technology, the goal was to reduce the raw-material requirements and manufacturing costs while at the same time obtaining more robust vehicles. For this reason, the wagon factory in Uerdingen received an order in 1938 to develop a lightweight tank car with a cargo volume of 30m³. As early as 1939, the three prototypes were handed over to two private goods-wagon rental companies as well as the state’s economic research association (Wirtschaftliche Forschungsgesellschaft (Wifo)) for testing. Following a small intermediate series in 1940, series production of the 30m³ Uerdinger-type lightweight tank wagon began in 1941. The largest customer was the German air force (Luftwaffe) with approx. 2,200 units, followed by the Wifo and many smaller companies, which resulted in a total of around 3,700 cars being built. In the post-war period, the wagons acquired by the Wifo and Luftwaffe were redistributed to other wagon operators in both German states. In the following decades, the wagons were primarily used by larger companies in the mineral oil industry, and also by smaller private companies as well as DB and DR themselves. Some of the wagons also remained abroad, where they were operated by new owners. In 2016 one of these wagons was still in use in internal interfactory traffic at Haltermann in Hamburg. Model Bogie with three-point support Individually mounted axle box cover Individually mounted wheelchocks Individually mounted brake systems Finely engraved bogies Brake blocks in wheel plane Individually mounted axle brake rod Free standing handle bars
On order, shipped within 10-15 days
Prototype 30m³ lightweight tank wagon in Uerdinger design – thanks to general technical advances in lightweight construction and welding technology, the management at the National Railway (Reichsbahn) decided to dispense with the actual vehicle frame when designing new tank wagons. Instead, the tensile and impact forces would, as far as possible, be absorbed by the boiler. Through the extensive use of welding technology, the goal was to reduce the raw-material requirements and manufacturing costs while at the same time obtaining more robust vehicles. For this reason, the wagon factory in Uerdingen received an order in 1938 to develop a lightweight tank car with a cargo volume of 30m³. As early as 1939, the three prototypes were handed over to two private goods-wagon rental companies as well as the state’s economic research association (Wirtschaftliche Forschungsgesellschaft (Wifo)) for testing. Following a small intermediate series in 1940, series production of the 30m³ Uerdinger-type lightweight tank wagon began in 1941. The largest customer was the German air force (Luftwaffe) with approx. 2,200 units, followed by the Wifo and many smaller companies, which resulted in a total of around 3,700 cars being built. In the post-war period, the wagons acquired by the Wifo and Luftwaffe were redistributed to other wagon operators in both German states. In the following decades, the wagons were primarily used by larger companies in the mineral oil industry, and also by smaller private companies as well as DB and DR themselves. Some of the wagons also remained abroad, where they were operated by new owners. In 2016 one of these wagons was still in use in internal interfactory traffic at Haltermann in Hamburg. Model Bogie with three-point support Individually mounted axle box cover Individually mounted wheelchocks Individually mounted brake systems Finely engraved bogies Brake blocks in wheel plane Individually mounted axle brake rod Free standing handle bars
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days
Prototype To promote the renewal of rolling stock and the standardisation of goods wagons among European state railways, the UIC (Union Internationale de Chemins de Fer) designed two variants of an open goods wagon at the beginning of the 1950s: the UIC Type I and UIC Type II. The UIC Type II closely adhered to the dimensions of 10.0 metres in length with a 5.4-metre wheelbase, drawing strong inspiration from pre-war German designs. The entire frame and wagon body were constructed using welded techniques. Upon completing the detailed design, the Federal Railway began upgrading its O-rolling stock at the Kaiserslautern workshop, using the UIC Type II as a basis. From 1954, 10,589 wagons of the Omm 54 types were produced in Kaiserslautern in just two years. Although officially considered conversions based on usable parts from older wagons, these wagons were largely built from new materials. An exception was the brake components, for which Kkg brakes from donor wagons were utilised. In the subsequent construction batches – designated as Omm 55 – these brakes were also dispensed with and new KE brakes were installed, resulting in the procurement of over 17,300 units from 1955 onwards. Through numerous detailed improvements during production as well as later design changes, the vehicles were maintained throughout their lifecycle and were not completely retired until 1994. In addition to the Federal Railway, other state railways also procured wagons based on the UIC Type II specifications for their fleets. These were deployed by the DR Ost (East German Deutsche Reichsbahn), SNCF, SNCB, FS, MAV, ÖBB (Austrian Federal Railways), SBB, CSD, DSB and others, each featuring country-specific details or components. Model Lots of design differences Variants with handbrake Lots of extra details Wheels profiled on both sides Car floor of metal Different versions of the brake systems Three-point bearing for safe operation Achshalter aus Metall Side doors with inside contours
On order, shipped within 10-15 days