Scenery
The semitrailer with rear lighting is equipped with a 5-pole plug-in coupling for the connection to the respective vehicle. By connecting to the tractor, the following functions are transferred to the trailer: Infrared transmitter for distance control Braking and reversing lights Direction indicators right/left and warning lights controllable L 10.9 x W 2.8 x H 4 cm
On order, lead time to be confirmed
The module allows the transmission of a variety of commands to CarMotion vehicles via infrared signals. These commands range from simple blinking to deceleration and stopping of CarMotion vehicles, for example in front of traffic lights. The two infrared transmitter diodes can be inconspicuously positioned alongside the road or placed horizontally in a small cut-out in the roadway or roadside. Like the vehicles, the module can be conveniently configured in the CarManager. All macros stored in the vehicles can be invoked by the module, including those that cannot be accessed through magnetic sequences for technical reasons. The two IR LEDs transmit different signals depending on the selected operating mode. One of the numerous applications is precise stopping in front of a traffic light or similar. The first IR LED is positioned some distance before the traffic light and sends the command for gradual deceleration when the traffic light is red. The vehicle then gently comes to a stop on an optional stop magnet (north pole). The second IR LED is located in close proximity to the traffic light and sends the start command when the light is green. The module is directly controlled by the Viessmann traffic light controller, items 5094 or 5095, or the level crossing items 5104 and 510) via the control input. The input also allows control of the module through a switch, relay contact, or DCC switch command using a suitable central control unit. Simple commands can also be generated by turning the module on and off, for example, to send blink commands only when a corresponding turnout is set. Board dimensions with cable outlet: ca. L 45 x W 5 x H 5 mm Recommended installation space (programming plug): ca. L 55 x W 5 x H 5 mm Cable length to the IR LEDs: each ca. 300 mm IR LED dimensions: ca. L 2 x W 1.2 x H 1.2 mm
On order, lead time to be confirmed
The IR Scanner is a locally deployed sensor unit designed to detect vehicle-specific information at defined points along the route. While vehicles are in motion, it captures relevant data in real time and makes this information immediately available to the traffic infrastructure. This enables situation-dependent control of routes, access points, and special zones – precise, automated, and efficient. Continuous data acquisition allows traffic flows to be differentiated in a targeted manner. For example, short vehicles can be preferentially guided into inner-city areas, while long vehicles or vehicle-trailer combinations are automatically routed along alternative paths. Access can also be selectively granted to specific vehicle types, such as allowing buses to enter designated stop areas while other traffic is diverted. Vehicles with a low battery charge can be directed to inductive charging zones, while vehicles with sufficient remaining charge continue without impacting traffic flow. The result is more efficient use of infrastructure while simultaneously relieving sensitive traffic areas.
On order, lead time to be confirmed
The magnetic bar enables you to switch your CarMotion vehicles on and off on your layout even from a distance. No need to lift the vehicle from the road. Length: 12.6 – 64 cm.
On order, lead time to be confirmed
To be used exclusively with the Proxxon angle grinder LHW/A item 29815. Suitable for our 1 mm magnetic tape item 8430. Contents: - enclosure with suction connection - depth limiter - disc cutter 3 mm
On order, lead time to be confirmed
The charger is specifically designed for smaller vehicles such as the Beetle, item 8090 and is optimally matched to the charging current of their batteries. It features the appropriate connector for these vehicle models.
On order, lead time to be confirmed
Functionally equivalent to the programming device for trucks and buses, item 8401, but equipped with a smaller connector designed for passenger vehicles, such as the Beetle, item 8090.
On order, lead time to be confirmed
With this set you can retrofit your long trailers and semitrailers of kibri and other manufacturers to be able to use the full scope of functions of the CarMotion vehicles. Contents: 1 bumper with 5-pole connection plug and infrared transmitter for distance control. Cable length: ca. 19 cm
On order, lead time to be confirmed
High-performance, low-wear motor for underfloor drive with encapsulated gear and one driven axle, suitable for CarMotion vehicles. Operating voltage: 7 – 12 V DC L 2.5 x W 2.8 x H 1.3 cm
On order, lead time to be confirmed
Front axle fully assembled with steering arm and magnet for CarMotion trucks. This front axle is suitable for vehicles with a distance of 45–55 mm from the front axle to the drive axle. Suitable vehicles: 8115, 8152, 8161, 8130, 8131, 8132, 8133, 8135 L 2.2 x W 2.8 x H 1.3 cm
On order, lead time to be confirmed
Lightweight, high-performance, and compact LiPo pouch cells with built-in protection electronics against overcharging, deep discharge, and overcurrent (short-circuit resistant). Replacement part for MB Actros vehicles, designed for operations with the cells connected in parallel. Nominal voltage 3.7 V, capacity each 60 mAh, maximum charge and discharge current 2 C (120 mA). L 22 x W 12 x H 4.5 mm
On order, lead time to be confirmed
Lightweight, high-performance, and compact LiPo pouch cell with built-in protection electronics against overcharging, deep discharge and overcurrent (short-circuit resistant). Replacement parts for MB round bonnet and Magirus square bonnet vehicles. Nominal voltage 3.7 V, capacity 120 mAh, maximum charge and discharge current 2C (240 mA). L 24 x W 12 x H 7.5 mm
On order, lead time to be confirmed
With this set you can retrofit your trailers and short semitrailers of kibri and other manufacturers to be able to use the full scope of functions of the CarMotion vehicles. Contents: 1 bumper with 5-pole connection plug and infrared transmitter for distance control.
On order, lead time to be confirmed
Front axle fully assembled with steering arm and magnet for CarMotion trucks. Suitable vehicles: 8000, 8001, 8002, 8003, 8010, 8011, 8012, 8013, 8014, 8015, 8016, 8017, 8018, 8019, 8020, 8021, 8022, 8023, 8030, 8031, 8032, 8033, 8034, 8035, 8036, 8040, 8041, 8050, 8051, 8052, 8053, 8054, 8055, 8060, 8061, 8065, 8070, 8071, 8072, 8114, 8155, 8160 L 2.2 x W 2.8 x H 1.3 cm
On order, lead time to be confirmed
These steered axles for semitrailers are excellently suited for driving smaller radii even with longer semitrailers, without having to widen the roads very much in the curves or the semitrailers getting too far into the lane of opposite traffic. Precisely guided by ball bearing mounted cogwheel mechanism.
On order, lead time to be confirmed
High-performance, low-wear motor for underfloor drive with encapsulated gear and one driven axle, suitable for CarMotion vehicles. The rear axle is non-driven and height-adjustable. Operating voltage: 7 – 12 V DC L 4 x W 2.8 x H 1.3 cm
On order, lead time to be confirmed
The universal electronics module for trucks offers compact solutions for retrofitting trucks over 7.5 tons with the proven driving characteristics of CarMotion trucks. The slim module (W 12.5 mm x L 26.5 mm) is particularly suited for tight installation spaces and operates in conjunction with the H0 gearbox with motor, item 8426. Power is supplied by two 60 mAh rechargeable batteries included in the set. This module is designed exclusively for use with this specific motor and battery configuration. An additional trim-to-size distribution board (approx.. W 7 mm x L 25 mm) can be shortened to L 17 mm and facilitates the connection of LEDs for lighting purposes and enables extra lighting effects. An expansion interface is provided for additional modules. The LEDs and sensors come pre-wired with enamelled wires, making installation straightforward. Expansion kits for further lighting effects will be available in the future. Set includes: Main board, distribution board, Hall sensor, charging and programming socket, 2 rechargeable batteries, rear bumper with lights and IR transmitter, mini board with IR receiver, mini board with reed switch and driver’s cab lighting, mini board with trailer connector
On order, lead time to be confirmed
For the proper installation of the magnetic tape, items 8429 and 8430 in freely designed road courses to avoid collision with oncoming traffic. Milling of the groove for the magnetic tape is done along the marking.
On order, lead time to be confirmed
For the proper installation of the magnetic tape, items 8429 and 8430 in freely designed road courses to avoid collision with oncoming traffic. Milling of the groove for the magnetic tape is done along the marking.
On order, lead time to be confirmed
Marking aid for marking the locations of the permanent magnets, item 8431 at the correct spacing relative to each other, in a magnetic sequence, and with respect to magnetic tape, items 8429/8430. L 7 x W 3 x H 0.4 cm
On order, lead time to be confirmed
Cable for extending the EasyChain line for the InduktivCharger, item 8408. Ideally suited for lengthening the EasyChain line and connecting remote InduktivChargers. Length: 0.5 m per cable
On order, lead time to be confirmed
The permanent magnet holder is the ideal solution for testing the CarMotion system. Equipped with one or more magnets, the holder can be flexibly positioned to the right of the roadway. This allows you to precisely verify whether – and at which point – the CarMotion vehicle detects and executes defined control commands. Its sturdy design enables quick setup and easy repositioning during test runs, ensuring accurate results under realistic conditions.
On order, lead time to be confirmed
With this set you can retrofit your kibri trailers or semitrailers to optimize the running smoothness and the tracking accuracy of the vehicle. This will improve the driving characteristics of the trailer resp. the semitrailer. Contents: 6 rubber wheels, 6 rims, 3 steel axles, 6 sockets. Suitable for trailer and semitrailer with up to 3 axles and single tyres.
On order, lead time to be confirmed
With this set you can retrofit your kibri trailers or semitrailers to optimize the running smoothness and the tracking accuracy of the vehicle. This will improve the driving characteristics of the trailer resp. the semitrailer. Contents: 8 rubber wheels, 4 rims, 2 steel axles, 4 sockets. Suitable for 2-axle trailer and semitrailer with twin tyres.
On order, lead time to be confirmed