Scenery
The car detector recognizes the steering magnet of passing vehicles and is installed beneath the magnetic tape or conductive wire. Exclusively designed for use with the IR module item 8403, the InduktivCharger (item 8408) and the speed cameras (items 1330, 1331 and 1332).
On order, lead time to be confirmed
The IR transmitting diodes are designed as a replacement component for the IR Mini, item 8403 and IR Scanner, item 8406. They come equipped with pre-wired connection leads (without pre-resistors). Cable length to the IR LEDs: approx. 300 mm Dimensions IR LEDs: approx. L 1.6 x W 0.8 x H 0.8 mm
On order, lead time to be confirmed
The IR transmitting diodes are designed as a replacement component for the IR Mini, item 8403 and IR Scanner, item 8406. They come equipped with pre-wired connection leads (without pre-resistors). Cable length to the IR LEDs: approx. 300 mm Dimensions IR LEDs: approx. L 1.6 x W 0.8 x H 0.8 mm
On order, lead time to be confirmed
This cable is designed for extending the 6-pin connector of the programming device, item 8401, or the charger, item 8400. Ideal for wiring hard-toreach modules, such as the IR Mini, item 8403.
On order, lead time to be confirmed
The universal electronics for buses offer compact solutions for retrofitting coach and transit buses with the proven driving characteristics of CarMotion trucks. The slim module (W 12.5 mm x L 26.5 mm) is particularly suited for tight installation spaces and operates in conjunction with the H0 gearbox and motor, item 8426. Power is supplied by one 120 mAh rechargeable battery included in the set. This module is designed exclusively for use with this specific motor and battery configuration. An additional trim-to-size distribution board (approx.. W 7 mm x L 25 mm) can be shortened to L 17 mm and facilitates the connection of LEDs for lighting purposes and enables extra lighting effects. An expansion interface is provided for additional modules. The LEDs and the sensors come pre-wired with enamelled wires, making installation straightforward. Expansion kits for further lighting effects will be available in the future. Set includes: Main board, distribution board, Hall sensor, charging and programming socket, rechargeable battery, mini board with IR transmitter, mini board with IR receiver, mini board with reed switch and driver’s cab lighting, 4 mini boards for interior bus lighting, mini board with trailer connector.
On order, lead time to be confirmed
This turnout is equipped with a powerful and low-noise drive featuring secure positioning achieved by a robust 10 mm motor with planetary gear. By rearranging the variable end stops, a left, right, or 3-way diversion can be selectively created. The electronics are housed compactly within the casing. The diverter can be controlled manually, via buttons/switches or our InduktivCharger, item 8408, enabling digital control capabilities. Like the vehicles, the turnout can be comfortably configured in the CarManager.
On order, lead time to be confirmed
Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module. Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz. Suitable vehicles: 8002, 8012, 8018, 8135. L 18 x W 8.8 x H 11.4 mm
On order, lead time to be confirmed
Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module. Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz. Suitable vehicles: 8019 L 22.5 x W 11.2 x H 9.3 mm
On order, lead time to be confirmed
Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module. Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz. Suitable vehicles: 8017, 8022, 8034, 8035, 8052, 8072. L 22.5 x W 11.2 x H 9.3 mm
On order, lead time to be confirmed
Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module. Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz. Suitable vehicles: 8040, 8160. L 2.5 x W 1.2 x H 1.1 mm
On order, lead time to be confirmed
Enhance your CarMotion layout with in-vehicle sound effects. The retrofittable sound modules are vehicle-specific, ensuring they are mechanically, visually, and acoustically tailored to each model. These modules reproduce engine sounds for starting and stopping, as well as various driving-related sounds, such as gear changes, brake squeals, and depending on the vehicle type, even reverse warning signals. The horn, and if equipped, a siren, can also be activated. The engine sound volume is adjustable. The selectable and adjustable sounds can be controlled via remote control, DCC command, infrared command, or magnetic sequence. The circuit board of the sound module is easily connected to the vehicle‘s circuit board using a four-pin connector and secured with screws. The previous left-side components, such as the exhaust and air tanks, are replaced with the new components that house the speaker. Please note that vehicles without the four-pin expansion socket cannot be equipped with a sound module. Output power 250 mW, efficiency 81 dBA, frequency range approx. 800 – 10 kHz. Suitable vehicles: 8041, 8114, 8115. L 2.5 x W 1.2 x H 1.1 mm
On order, lead time to be confirmed
This module is ideal for designing a wide variety of model scenes. It can, e. g. serve as a connecting element or a thematic intermediate segment that integrates seamlessly into a larger layout. Features include a pre-milled groove for 1 mm magnetic tape, item 8430 and breakout holes for the InduktivCharger, item 8408 or turnout, items 8445/8448. Supplied with acrylic glass panels for edging. L 90 x W 54 x H 10 cm
On order, lead time to be confirmed
The track (item 8461) is a practical addition to the Viessmann CarMotion base module (item 8460). It has been specially developed for testing and demonstration purposes. The precisely cut, printed cardboard is placed on the base module, enabling a quick and effective demonstration of the system. Please note: The track is made of printed cardboard and is therefore not designed for continuous use. It is suitable for temporary use, e.g. at trade fairs, demonstrations or for testing purposes L 88 x W 52 cm
On order, lead time to be confirmed
For attaching CarMotion modules, e. g. InduktivCharger, item 8408, or turnout, item 8448, from below.
On order, lead time to be confirmed
This practical accessory set includes a remote control, 10 meters of magnetic tape (0.5 mm), 10 permanent magnets, as well as a charger and a programming device.
On order, lead time to be confirmed
This nice alpine set consists of church St. Andrä item-No. 43709, alpine house Wetterstein item-No. 43703 and alpine house item-No. 49251. Best way to start with a small alpine village. Dimensions: 43703: L 12 x W 11 x H 8,5 cm. 43709: L 18,6 x W 14 x H 28,5 cm. 49251: L 12,5 x W 13 x H 7,8 cm.
On order, lead time to be confirmed
Ø 3.5 x H 3.6 cm
On order, lead time to be confirmed
This Christmas village fits wonderfully into any winter layout. Or build together with your kids or grand children, a great set for Christmas Eve. The single building offers decoration on the fire place or on the window bank. Just imagine. Contains: Silent Night Memorial Chapel, post office Christkindl, mulled wine kiosk, gingerbread house and kiosk Bratwurst Maxe. The chapel comes with an LED for the interior lighting. Dimensions: Chapel L 11 x W 8 x H 16 cm / Post office L 10,5 x W 9,7 x H 8,3 cm / Gingerbread house L 10,5 x W 9,7 x H 8,3 cm / Bratwurst-Maxe L 6 x W 6,5 x H 7,8 cm / Mulled wine kiosk L 6,2 x W 6,3 x H 3,3 cm.
On order, lead time to be confirmed
When the days get chilly during autumn and winter time, there are chestnut kiosks in the pedestrian zones. The chestnuts in paper bags are hot and the little snack is eaten during a shopping tour. Dimensions: L 4,5 x W 4 x H 4 cm.
On order, lead time to be confirmed
Dimensions: L 9,5 x B 0,7 x H 12,7 cm. Passage height 9 cm / Passage width 4.9 cm
On order, lead time to be confirmed
Dimensions: L 13,6 x B 0,7 x H 12,7 cm. Passage height 9 cm / Passage width 9.3 cm.
On order, lead time to be confirmed
Dimensions: L 14,7 x B 0,8 x H 14,9 cm. Passage height: 9,4 cm. Passage width: 9,4 cm.
On order, lead time to be confirmed
Kit. Viaduct with track bed and 3 arches is an ideal bridge construction for any layout with standard space. Using the single bridge element item-No. 42512 the viaduct can be enlarged into any size. Suitable for all common track systems. Dimensions: L 30,3 x W 6,5 x H 12,6 cm. Road width: 4 cm. Road height: 11 cm. Passage height: 9 cm. Passage width: 7,5 cm.
On order, lead time to be confirmed
Dimensions: L 8 x W 3 x H 7,8 cm.
On order, lead time to be confirmed