Accessories
LED lighting strip, cabin, 1 LED, „warm-white“, 15,0mm x 6,9mm x 2,3 mm Small modules that can easily be installed either in cabs or as end-of-train lights make fitting protypical lighting of your vehicles a simple task. They provide one warmwhite LED or two red LEDs including the needed electronics. Part No. 50704 LED lighting strip, cabin, 1 LED, „warm-white“, 15,0mm x 6,9mm x 2,3 mm 50705 LED lighting strip, taillight, 2 LED, „Red“
In stock: 1 on the shelf, shipped within 1-3 days
SwitchPilot Extension, 4 twin-relays (DPDT) output, 2A each, extension for Switch Pilot Family If required, SwitchPilot can be augmented with the SwitchPilot Extension Modul: Plugged in at the side of the SwitchPilot, it offers four relay-driven outputs, used for switching potential-free loads, or for polarizing the frog; the ideal supplement for tricky circuitry. Modes of operation The SwitchPilot Extension Modul only works in conjunction with a SwitchPilot. Plugged in at the side, it gets its electrical power directly from the SwitchPilot. It contains a total of 4 Twin-Relays (2 x DPDT), of which each is dedicated to a pair of transistorized SwitchPilot outputs. The respective relay’s switch position is directly dependent upon the state of this pair of outputs. With the relay’s help, loads can be switched, galvanically separated from the rest of the track (it functions like a k84), or a motorized turnout can be polarized. With the relay’s 1.5 Amp continuous rating, either frogs can be polarized-, or blocks powered signal dependent, or motorized devices, such as (water) pumps may be switched. Especially intricate is the option to control motorized turnouts: Of course the SwitchPilot Extension Module easily handles the necessary motor polarization as well.
In stock: 1 on the shelf, shipped within 1-3 days
SwitchPilot 3 Servo, 8x servo decoder, DCC/MM, OLED, with RC-Feedback, updatable SwitchPilot 3 servo decoders are optimized for stationary use on your system and can control up to eight RC servo drives. In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 Servo has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons. Modes The SwitchPilot 3 servo is multi-protocol and can be used with workstations according to the Märklin® Motorola® system (e.g. 6021, Central Station® or Mobile Station®) as well as DCC-enabled central. The configuration can take place on both the main track and the programming track. Thanks to RailCom®, CVs can also be read out. Functioning The SwitchPilot 3 servo can be supplied directly from the digital system or an external DC or AC voltage source. The SwitchPilot 3 servo has eight outputs for the control of RC servo drives. In doing so, it can control these drives so precisely that, in addition to switching switches, any other slow movement sequences can be controlled. The SwitchPilot 3 servo has a built-in power-on pulse suppression to eliminate or reduce the system-related "twitching" of RC servos when applying the supply voltage. Furthermore, the power supply to the servo can be interrupted to prevent a "hum" of some inexpensive servos. Each of the eight servos can be operated either in "digital mode" or in the "proportional mode" introduced for the first time with the SwitchPilot 3 servo: In digital mode, the servo can start two end positions "A" and "B", depending on the switching position on the control panel. The position of the two end positions as well as the speed at which thethe servo moves in the desired direction, can be individually set on the SwitchPilot 3 servo. The digital mode is perfect for switching switches or signals that should always remain in a fixed position. In proportional mode, the servo can move and stop in any position within the end positions "A" and B. The servo only runs as long as the control panel sends a command. If you release the button, the servo stops. In this way, a servo can be stopped in any desired position. The servo speed can be adjusted individually. The proportional mode is ideal for (water) cranes or engine shed gates or any other application, for which intermediate positions are also required. For each servo, in addition to the end positions and the rotational speeds, it can be determined whether it should rock up when reaching the final position. Furthermore, the generation of the servo pulse can be influenced to adapt to the different RC servos on the market or the power supply of each servo can be switched off individually. In this way, cheap so-called so-called Analog servos as well as modern digital servos (with microcontroller) optimally controlled. Analogue Operation The SwitchPilot 3 servo can be used as a special feature without a digital control panel: On request, up to 16 buttons can be connected for direct switching of the servos. Set The SwitchPilot 3 servo can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom® CVs. On request, he also learns the addresses directly via a programming button. The setting is, of course, the simplest with the integrated OLED displays as well as the three input buttons: All (!) Settings can be checked directly on the decoder and changed on request. "Programming" with the help of your headquarters is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 servo are protected against overload. We want you to enjoy your decoder for as long as possible.
In stock: 1 on the shelf, shipped within 1-3 days
Super thin cable, 0.5mm diameter, AWG36, 10m bundle, white colour Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
In stock: 1 on the shelf, shipped within 1-3 days
Adapterplatine PluX22 for 9 outputs, with soldering pads and wires Our new adapter board 3 for decoders with PluX22 interface is best suited for everyone intending to digitise a loco without interface but with many functions without having to carry out major soldering work. The adapter board with its compact dimensions of 32.5mm x 15.5mm is equipped with an extra mounting lug that can be easily broken off if not required. All outputs as per VHDM resp. NEM standard are accessible as soldering pads. For easy handling and wiring the most important contacts are already equipped with 200mm long wires. Dimensions: Length 33.0mm x 15.5mm (With mounting tab: 38.0mm x 15.5mm) Art.No. Delivery 51958 Adapterplatine PluX22 for 9 outputs, with soldering pads and wires
In stock: 1 on the shelf, shipped within 1-3 days
Ski change-over electronics for use with LokSound/LokPilot decoders V3.5 (or newer) with 21MTC (not MKL) connector. Many railcars are equipped with a grinder at both ends. For proper function in block locations and for timely stopping in front of red signals, it is essential that depending on the direction of travel, only one grinder is used to power the decoder. The grinder switch ensures this: it is hung between the pantograph and a LokPilot or LokSound decoder with a 21MTC interface. These generate a control signal that evaluates the grinder switchover electronics and switches the "correct" grinder. It works perfectly in digital and analog mode. The base of the board has the dimensions 43mm x 24mm. Note: The LokPilot Basic V1.0 and MKL decoder are not suitable for the grinder switching electronics.
In stock: 1 on the shelf, shipped within 1-3 days
Smoke distillate, 125 ml bottle Developed specially for the diesel and steam locomotives of the ESU Engineering Edition. It produces realistically dense, white smoke and evaporates without residue: no traces in the smoke generator, on locomotive or building roofs, or on the layout. It wipes off easily with alcohol and does not attack the paintwork or patina of your models. It also works in all other known smoke generators, in locomotives as well as ship models and model buildings. Danger: may be fatal if swallowed and enters airways. Store locked up. If swallowed, immediately call a poison centre or doctor; do not induce vomiting.
In stock: 1 on the shelf, shipped within 1-3 days
Adapter cable, 18-pin Next-18 socket to NEM651 6-pin, Flex, 88mm, with heat shrink tube Sometimes, the locomotive is still equipped with an "old" 6-pin interface compliant with NEM 651. Using this flexible PCB, which can be folded and cut to length almost at will, you can easily install a modern decoder with a Next18 interface. The adapter board comes with heat-shrink tubing. Art.No. Delivery 51994 Adapter cable, 18-pin Next-18 socket to NEM651 6-pin, Flex, 88mm, with heat shrink tube
In stock: 1 on the shelf, shipped within 1-3 days
Adapter cable, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube Due to space constraints, some HO locomotives with the "old" 8-pin NEM-652 interface cannot accommodate a standard HO decoder. With the help of this flexible PCB, which can be folded and cut to length as needed, you can install a modern, compact N-scale decoder featuring a Next18 interface. The adapter board comes with heat-shrink tubing. Art.No. Delivery 51995 Adapter cable, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube
In stock: 1 on the shelf, shipped within 1-3 days
Adapter board, Next18 socket to Plux16 Some N or TT scale models are equipped with a PluX16 interface. This adapter board is suitable for installing a LokSound 5 micro or LokPilot 5 micro in such models; simply plug it in between the locomotive and the vehicle to use a decoder with a Next18 interface. Please take the installation depth and available space into account. Art.No. Delivery 51996 Adapter board, Next18 socket to Plux16
In stock: 1 on the shelf, shipped within 1-3 days
PowerPack Mini enery buffer for LokPilot V4.0, LokSound V4.0, LokPilot 5 family and LokSound 5 family, 1F/2.7V The new ESU PowerPack Mini can be wired to all fourth and fifth generation ESU decoders. It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound module. Subject to the energy consumption of your model it may continue to move for up to three seconds. The PowerPack Mini incorporates an integral charging circuit controlled by the decoder. Therefore it may be connected even during programming. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). Although it is considerably smaller than its predecessor, the space requirements of the PowerPack Mini of about 15.7 mm x 9.7 mm x 13 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Mini to the decoder. The wires are already soldered to the PowerPack Mini and must be soldered to the appropriate solder pads of the decoder. Please note that the PowerPack cannot operate in analogue mode due to technical reasons: Buffering is therefore not possible in analogue mode. Art.No. Delivery 54671 PowerPack Mini enery buffer for LokPilot V4.0, LokSound V4.0, LokPilot 5 family and LokSound 5 family, 1F/2.7V
In stock: 1 on the shelf, shipped within 1-3 days
LokSound 5 micro DCC Direct Kato Japan »Blank decoder«, gauge: N The LokSound 5 micro DCC Direct Kato Japan has been specially developed for installation in Kato-branded track N vehicles: in many European and Japanese locomotives of this manufacturer, the ser decoder can be installed directly below the engine instead of the analog board installed as standard. Finally, these models can also be easily retrofitted with a LokSound decoder. The LokSound 5 micro DCC Direct Kato Japan with its dimensions of 27.6mm x 14.1mm x 3mm is a pure DCC decoder and comes without a loudspeaker. Modes The LokSound 5 micro DCC Direct Kato Japan is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully to a suitable digital center.It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokSound 5 micro DCC Direct Kato Japan Decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An AUTOMATIC ABC commuter train allows automatic commuting between two stations. The LokSound 5 micro DCC Direct Kato Japan can be used on analog DC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Sound The LokSound 5 micro DCC Direct Kato Japan Decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz and offers hi-fi quality on its system. There is virtually no difference to the original audible anymore. A Class-D audio output with up to 3W output power controls the speakers, which can have between 4 ohms and 32 ohms impedance. A 128 Mbit sound memory provides enough capacity. All individual noises can be adjusted individually in the volume. The super-flexible sound engine without a rigid schedule allows the exemplary simulation of all conceivable rail tracks. Functions Although the LokSound 5 micro DCC Direct Kato Japan is normally installed in the motor car of a drive car set, three reinforced function outputs for lighting are available at their own discretion. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokSound 5 micro DCC Direct Kato Japan has a variable PWM clock frequency from 10kHz to 50kHz, which ensures a super-quiet drive, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokSound 5 micro DCC Direct Kato Japan Decoder delivers up to 0.9A motor power. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 58731 LokSound 5 micro DCC Direct Kato Japan »Blank decoder«, gauge: N
In stock: 1 on the shelf, shipped within 1-3 days
With the LokSound 5 Nano DCC, ESU has succeeded in developing an even smaller LokSound decoder! Thus, it should really be used in all vehicles of nominal sizes N and TT.
In stock: 1 on the shelf, shipped within 1-3 days
LokPilot 5 Basic, 8-pin NEM652, Gauge H0, 0 While LokPilot 5 decoders can undoubtedly meet all imaginable requirements of even the most demanding experts, many model railway eras are looking for a robust, high-quality DCC decoder for your standard requirements, which should also be affordable. The LokPilot 5 Basic was developed with the aim of offering a modern decoder with a reasonable range of functions at a reasonable price. The LokPilot 5 Basic comes in two versions: In addition to a version with an 8-pin NEM interface, a version with 21MTC interface is also available. This makes the LokPilot 5 Basic particularly suitable for use in track H0 vehicles. Modes The LokPilot 5 Basic is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 20 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully automatically to a suitable digital center. It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokPilot 5 Basic Decoder detects the Märklin® brake distances as well as the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible.The LokPilot 5 Basic Decoder can be used on analog DC webs. The maximum speed can be set separately.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Basic has 4 reinforced function outputs in each version. In the 21MTC interface, there are 8 logic-level outputs at the interface, two of which are also suitable for controlling servos. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 Basic delivers up to 0.9A continuous current. A variable PWM clock frequency from 10kHz to 50kHz ensures super-quiet operation, especially for bell anchor motors – The typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Basic to bridge dirty rail cuts. Protection Of course, all function outputs as well as the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59020 LokPilot 5 Basic, 8-pin NEM652, Gauge H0, 0 59029 LokPilot 5 Basic, 21MTC NEM660, Gauge H0, 0
In stock: 1 on the shelf, shipped within 1-3 days
LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 The LokPilot 5 Fx DCC is a function decoder with NO MOTOR CONTROL and is therefore perfect for installation in control cars (Cab Cars) or rail vehicles that only need lights and/or lighting effects. As the "twin brother" of the LokPilot 5 Fx, it shares its features and the basic characteristics of all other LokPilot 5 decoders, but is a pure DCC decoder. The LokPilot 5 Fx DCC is supplied in three versions: In addition to the "classic" version with 8-pin NEM 652 wiring harness, a version for the 21MTC interface and a PluX22 interface is also available. Operating Modes The LokPilot 5 Fx DCC is a pure DCC decoder. 14 to 128 speed steps are as standard as short (1-127) and long (128-9999) addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable command stations such as those from ESU. Auxiliary CVs exist for command stations that can only program the CVs from 1-255. The LokPilot 5 Fx DCC decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An automatic ABC shuttle train system enables automatic shuttle operation between two stations. Although this decoder does not have motor control, it is important for the decoder to be able to synchronize non-motorized rail vehicles with those that are motorized. The LokPilot 5 Fx DCC decoder can be used on analog DC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustments are required. Functions The LokPilot 5 Fx DCC has been equipped with an astonishing number of function outputs. Depending on the interface version, each LokPilot 5 Fx DCC decoder offers at least 10 powered function outputs, each with a max output current of 250mA for lights. Versions with a PluX22 or 21MTC interface also feature 4 outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. Interaction The LokPilot 5 Fx DCC is designed to work with the LokSound 5 and the LokPilot 5 decoders: For example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 decoder and the control car (Cab Car) with a LokPilot 5 Fx DCC. Provided they have the same address, both behave identically. The identical CV arrangement makes it easier to coordinate the two decoders. Operational reliability A PowerPack can be connected to the LokPilot 5 Fx DCC to bridge dirty track sections. Protection The outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Technical Specifications Operating Modes: NMRA/DCC with 14, 28, and 128 speed steps, DCC RailCom® DCC 2-digit and 4-digit addresses (short and long addresses) Analog DC voltage (can be switched off). Automatic detection of operating mode and DCC speed step setting Support for Lenz® LG100, Märklin®, Roco® braking sections, and ZIMO® HLU commands Support for ABC braking mode and ABC shuttle train section Wrong-way bit / saving operating states Shunting mode and acceleration and braking delay can be switched via button Speed controller: NO MOTOR CONTROL Function outputs: 10 powered function outputs Version with 21MTC interface has 2 additional logic level outputs and 2 further logic level outputs instead of SUSI Version with PluX22 interface has 2 logic level outputs instead of SUSI 250mA load capacity per powered output Total current of all function outputs approx. 1500mA. Short-circuit-proof outputs Functional output assignments freely selectable (function mapping) Dimensions: 16.5 mm x 15.5 mm x 4.5 mm Instruction manual Art.No. Delivery 59220 LokPilot 5 Fx DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 59222 LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 59229 LokPilot 5 Fx DCC, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0
In stock: 1 on the shelf, shipped within 1-3 days
LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl. The decoder accepts all DCC programming modes and thanks to RailCom® the CV values can be read on the main track with RailCom equipped DCC systems. For command stations that only program the CVs from 1-255 auxiliary CV registers exist. The LokPilot 5 DCC decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACKCommands or the Lenz® ABC system. Also braking with DCC brake modules or with DC voltageis possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle trainenables automatic commuting between two train stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The top speedcan be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5DCC packed with function outputs. Depending on the interface version, each LokPilot offers 5 DCCDecoder at least 10 amplified function outputs with 250mA output current each. In the executionswith PluX22 or 21MTC interface there are 4 outputs to control servos orLogic level outputs added. All-important lighting functions are available. The brightness of each outputcan be set separately. The decoder masters automatic pushing and pullingwhen uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 DCC has been fundamentally improved again. A variably adjustablePWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors.Operation - The typical “hum” is a thing of the past. The load control now has up to10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enablesthe automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to 1.5A of motor current. Enough juice even for older motors. Operational safety On request, a PowerPack can be fitted to the LokPilot 5 DCC to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Analog Gleichspannung (abschaltbar). Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59620 LokPilot 5 DCC, 8-pin NEM652, gauge H0 ,0 59622 LokPilot 5 DCC, PLUX22 NEM658, gauge H0 ,0 59626 LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 59629 LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 59659 LokPilot 5 DCC, 21MTC MKL, gauge H0 ,0
In stock: 1 on the shelf, shipped within 1-3 days
Modular cable, RJ12 plug to RJ12 plug, 6 wires, all assigned, 1:1, length: 2 m. Connection cable for all common LocoNet modules.
In stock: 1 on the shelf, shipped within 1-3 days
Eye-catcher! Light-emitting diodes with built-in microcircuit, to be used wherever a flashing lamp is required, e. g. as a visual signal on stationary models of vehicles (police, rescue service, fire brigade, construction industry, municipal companies, or agriculture), during gate opening and shutting movements, for the illumination of funfair models, and many others more. Supply voltage: 3-4 V DC Current input: up to 20 mA Flashing rate: approx. 1.5 Hz International component size: 0805 Length: 2 mm Width: 1.25 mm Height: 1.1 mm Advice: For lighting effects on Car System vehicles, use the Flashing lights, Art. 163760 to 163765.
In stock: 1 on the shelf, shipped within 1-3 days
Gauge: H0, N, TT, Z Cross-section: 0.04 mm² Contents: stranded wire in 10 colours, 10 m each
In stock: 1 on the shelf, shipped within 1-3 days
This low-viscosity adhesive is perfect for permanently fixing gravel and sand. Simply apply the adhesive slowly to the desired area to create a stable, long-lasting bond. No additional aids are required, which makes it particularly easy to use!
In stock: 1 on the shelf, shipped within 1-3 days
This adhesive for pros reacts quicker, adheres quicker and more permanently. With a special needle applicator and protective cap for the needle.
In stock: 1 on the shelf, shipped within 1-3 days
This new adhesive allows you to create reliable bond lines between Styrodur, Styropor and Decorflex materials, as well as foamed structural rigid foam parts. It dries crystal clear, yet remains flexible, adheres to smooth surfaces, and bonds scatter materials to plastic parts without causing them to warp.
In stock: 1 on the shelf, shipped within 1-3 days
Transparent can with write-on label for storing all kinds of strew materials for layout construction. Two hinged openings are integrated in the screw cap and make for comfortable and exact dosing.
In stock: 1 on the shelf, shipped within 1-3 days
Model of a modern path light. The filigree design of this lamp has a special charm. This makes it particularly suitable for illuminating paths, parks and gardens. The pedestal light is equipped with long-lasting LED technology. Height: 15 mm. Light colour: warm white. The product is ready for connection for 12 V, direct voltage (DC). Use the transformer, Art. 180699, to operate the light.
In stock: 1 on the shelf, shipped within 1-3 days