Accessories
The French edition of the main catalog has a format of 29 x 21 cm. In full color, with very detailed pictures and a complete product description Highlights Quick overview High image quality Full color
In stock: 1 on the shelf, shipped within 1-3 days
Controller with a 230 V / 18 VA switched-mode power supply. Four-stage speed control for a slow start and a powerful increase in speed up to maximum speed. Single-knob operation for setting the track voltage and for determining the direction of travel by turning the control knob out of the centre position. Dimensions of the controller: 130 mm (L) x 70 mm (W) x 50 mm (H).
In stock: 1 on the shelf, shipped within 1-3 days
Makes it easier to place vehicles on the track. Even for a locomotive with several axles a single movement is enough.
In stock: 1 on the shelf, shipped within 1-3 days
Interior lighting for the Märklin Bavarian and Palatinate express train passenger cars 41354, 41358, 41359, 41369 and 41379.
In stock: 1 on the shelf, shipped within 1-3 days
Decoder for all DC locomotives with a current consumption of up to 2000 mA (motor 2000 mA, lighting 300 mA). Suitable for digital locomotives with an 8-pin digital interface to NEM. Universally usable in Selectrix and DCC format. Automatic system and analogue detection. Same locomotive address in Selectrix and DCC operation. 7 adjustable maximum speeds. 4 adjustable motor pulse variants. Automatic load compensation. Connection for lighting function. Connection for additional function. 4-pin SUSI interface for further special functions in DCC operation. Short-circuit protection of the motor output. Overload protection of the lighting output. Overload protection of the additional function. Programming of additional settings by selecting address "00", e.g. fine graduation of the pulse widths (control variant), polarity reversal of the direction of travel in Selectrix operation: 31 speed steps. 111 addresses. Block section operation with simple diodes (1 or 2 stopping sections). Braking mode with brake diode. in DCC operation: Manual speed step selection 14/28 steps. Automatic switchover to 128 speed steps. Addresses optionally 7-bit or 14-bit. Braking mode with DC voltage and "broadcast-mode" braking generators Dimensions approx. 24.2 x 15.4 x 3.9 mm.
In stock: 1 on the shelf, shipped within 1-3 days
Replacement for all 23 mm festoon bulbs with 12–19 V, as used e.g. in Roco, Lima and Ade coaches.
In stock: 1 on the shelf, shipped within 1-3 days
LocoNet cable tester – the quick way to error-free LocoNet wiring. With this tool, you can quickly and easily check your LocoNet wiring before and after installation: detection of short circuits, continuity test, twisted or untwisted LocoNet cable, test of single and multiple cables. The tester consists of the main unit (Master) with an on/off switch for fast or slow test sequence and a detachable accessory unit (Remote); the LED chains 1 to 6 of both units show the test result as a running light. Contents supplied: LocoNet cable tester, protective case, 9-V block battery, 3 m LocoNet spiral cable, LocoNet coupling, operating instructions.
In stock: 1 on the shelf, shipped within 1-3 days
With the new mfx module, your Intellibox II also communicates with the mfx® vehicles on your layout. Through automatic registration, the vehicles are entered into the Intellibox II database with their names and associated special function symbols, so that they can be selected and operated immediately with full convenience. You can now reach directly
In stock: 1 on the shelf, shipped within 1-3 days
Free address setting without decoder presets Points and signals with a solenoid drive that are to be controlled digitally must be fitted with a solenoid accessory decoder. Lamps, colour-light signals or track sections that are to be switched on and off digitally are digitalised with a switching decoder. Uhlenbrock solenoid accessory and switching decoders can be used in Märklin, Motorola and DCC digital systems. In Motorola mode, addresses 1–320 can be addressed with the Intellibox, and addresses 1–256 with other command stations. In DCC mode, addresses 1–2048 are possible. The addresses are not preset. They can be freely chosen independently of one another. Each module has two outputs. Depending on the type, both outputs can be addressed together under one address or independently of one another under two addresses. The relay contacts of the switching decoders have potential-free outputs and can be connected as required. Each output can carry a load of 1 A. By limiting the connections to two per module, cable runs stay short and the wiring of the layout stays clear. Connection is conveniently made via screw terminals. Setting the address is extremely simple. First the decoder's programming button and then the corresponding point button on the control panel are pressed. The decoder simply remembers the corresponding address. The decoders are supplied with operating voltage and control information from the digital command station. Universal switching decoder with two separate, potential-free changeover contacts that can be addressed together under one address. One contact can, for example, operate a colour-light signal and the second can switch the track voltage. Art. no. 67500 SD1 switching decoder
In stock: 1 on the shelf, shipped within 1-3 days
Points and signals with a solenoid drive that are to be controlled digitally must be fitted with a solenoid accessory decoder. Lamps, colour-light signals or track sections that are to be switched on and off digitally are digitalised with a switching decoder. For Motorola and DCC digital systems Depending on the type, for pulsed or continuous current Large address range Free choice of address Address setting at the push of a button Relay contacts with potential-free outputs High load: 1 A per output Simple connection Size: 38 x 32 x 15 mm Uhlenbrock solenoid accessory and switching decoders can be used in Märklin, Motorola and DCC digital systems. In Motorola mode, addresses 1–320 can be addressed with the Intellibox, and addresses 1–256 with other command stations. In DCC mode, addresses 1–2048 are possible. The addresses are not preset. They can be freely chosen independently of one another. Each module has two outputs. Depending on the type, both outputs can be addressed together under one address or independently of one another under two addresses. The relay contacts of the switching decoders have potential-free outputs and can be connected as required. Each output can carry a load of 1 A. By limiting the connections to two per module, cable runs stay short and the wiring of the layout stays clear. Connection is conveniently made via screw terminals. Setting the address is extremely simple. First the decoder's programming button and then the corresponding point button on the control panel are pressed. The decoder simply remembers the corresponding address. The decoders are supplied with operating voltage and control information from the digital command station. Universal switching decoder with two potential-free changeover contacts that can be addressed independently of one another under two addresses. The decoder switches two different loads independently of one another, for example lamps or motorised point drives. Art. no. 67600 SD2 switching decoder
In stock: 1 on the shelf, shipped within 1-3 days
MARCo receiver + feedback module RailCom® automation + genuine feedback Now not only vehicles equipped with a RailCom® transmitter can be detected, but all other vehicles as well. The MARCo receiver contains two RailCom® detectors and two feedback modules for monitoring two track sections. In addition, it has an intelligence that can carry out switching operations independently. The connection to the digital command station is made via LocoNet. If simple switching functions are to be carried out independently of the direction of travel, one module can monitor two track sections. Only the address of the passing locomotive is transmitted and simple switching tasks are carried out. At locations where an automatic function dependent on the direction of travel is to be carried out, the two track sections of one detector are installed one behind the other in the track. In this way, the direction of travel is detected in addition to the address, and the automation can stop the train precisely in the second section.
In stock: 1 on the shelf, shipped within 1-3 days
The standard decoders for small gauges are the 73xxx series. These decoders are available with connecting wires (73300), with 6-pin plug to NEM 651 (73310) and with PluX12 interface (73340). This can be used, for example, to equip Tillig locomotives. The highlight is the 73236 decoder for locomotives with the Next18 interface. It is even fitted with the Intellimatic. Our new 73406 decoders with connecting wires and 73416 with 6-pin plug to NEM 651 are intended for the smallest locomotives. They are distinguished by a very small size while achieving high performance. Thanks to the built-in protection mechanisms, these decoders are extremely robust even at this small size. All IntelliDrive 2 decoders have RailComPlus®, Selectrix®, ABC braking and extended function mapping, and can be updated on the track. For easy plugging in of a sound module, the decoders are fitted with a SUSI or microSUSI interface. On the Next18 decoder, the SUSI connections are found on the connector strip. Together with the IntelliSound-microModul or IntelliSound-kompaktModul, an extremely small decoder-sound combination results. Art. no. 73310 Decoder, microSUSI, Multi, DC, control, wire
In stock: 1 on the shelf, shipped within 1-3 days
The digital decoder is the brain of your locomotive. It determines the running characteristics and switching options. A poorly chosen decoder can quickly spoil your enjoyment of the vehicle. IntelliDrive decoders are at the forefront of technology and guarantee you optimal running characteristics.
In stock: 1 on the shelf, shipped within 1-3 days
Coloured spare bulbs. All lamps are long life quality.
In stock: 1 on the shelf, shipped within 1-3 days
Suitable for house illumination socket item 6832.
In stock: 1 on the shelf, shipped within 1-3 days
The fith edition of the catenary book, German version, offers a lot of information about the subject catenary. On more than 130 pages you get information about the history and support ideas to assemble prototypically.
In stock: 1 on the shelf, shipped within 1-3 days
The blaze flickering generates a realistic fire effect of a blazing fire. Up to 7 red and yellow miniature bulbs all flicker in a different rhythm, suggesting to the observer the striking effect of a real burning fire. The intensity can be adjusted steplessly to suit the specific application and your own desire. The following applications are possible: Burning houses, camp fires (in the forest, by the lake), stoves etc. The set includes 2 yellow and 1 red bulbs. It is possible to upgrade to 7 bulbs items 3501 (yellow), 3502 (red) and 3503 (clear). Useable with camp fire item 5022.
In stock: 1 on the shelf, shipped within 1-3 days
The blinker electronics is used to equip the model train vehicles with very realistic flashlights. A special blink switching, which is mounted under the layout, provides real effective rotating flashlight. All 4 connectable spare bulbs are blinking separately. Operation allowed only with AC voltage. Spare bulbs: Items 3500 - 3503.
In stock: 1 on the shelf, shipped within 1-3 days
Subsequent mounting in existing vehicle models. Maintenance free by LED lighting.
In stock: 1 on the shelf, shipped within 1-3 days
The circuit board with high intensity, power-saving and maintenance free LEDs can be shortened and divided variously. Lighting intensity adjustable by a potentiometer. Additionally included are two soldering pads to connect rear lights. The supplied sitting figurines bring some life into the passenger cars. Can be used in any coach of all manufacturers designed to be equipped with lighting. The circuit is to be fixed under the waggon roof and can be adjusted to any waggon length by cutting. Flicker-protection and constant current source for steady brightness integrated. Current supply either by the sliding contactor/wheel-rail contactors of the waggon or by our current-carrying couplings. Suitable for DC, AC or digital supply voltage. Max. power input approx. 22 mA. Dimensions: L 0,7 x W 21,1 cm.
In stock: 1 on the shelf, shipped within 1-3 days
Set with 2 St. Andrew's crosses without blinker electronics. Maintenance free by LED lighting. Suitable blinker electronics item 5065. Height: 3,6 cm.
In stock: 1 on the shelf, shipped within 1-3 days
Set with 2 St. Andrew's crosses with blinker electronics item 5065. Maintenance free by LED lighting. For automatic operation electronic relay item 5552 and switching tracks resp. switching contact item 6840 are required. Height: 3,6 cm.
In stock: 1 on the shelf, shipped within 1-3 days
Coach lighting with maintenance free, power-saving, bright LEDs with integrated multi protocol decoder (Motorola/DCC). Brightness adjustable by CVs and potentiometer. Can be used in any coach of all manufacturers designed to be equipped with lighting. By shortening the circuit board, it can be adapted to various waggon lengths. Integrated flickering protection for constant light even with short interruptions of the voltage supply, additional capacitors/power packs can be connected. Various lighting effects are adjustable, as start-up simulation of track bed inverter or single flickering tubes. The model offers direction depending switching outputs for front- and rear lighting. An additional switching output up to 150 mA capacity completes the functionalities. Power supply by grinder/point unit or conducting couplers items 5048/5071. Suitable for DC, AC or digital power. Due to low-loss switching regulator the coach lighting warms up only a bit. Maximum power input 20 mA. Dimensions: L 25,4 x W 0,8 cm.
In stock: 1 on the shelf, shipped within 1-3 days
Draw a railway ticket prior to departure! With high quality pad printing. L 0.6 x W 1 x H 2.4 cm
In stock: 1 on the shelf, shipped within 1-3 days