Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Electronics

Command stations, decoders, boosters and wiring for digital control, whatever your system.
Filter products
BM2 brake module
Lenz Elektronik 22610
BM2 brake module

The BM2 not only allows the train to be stopped at "Hp 0" before the signal, but also offers the installation of a slow-running section for "Hp 2". The track section before the signal is divided into a running section and a braking section. The length of the running section must be designed so that the longest train operating there fits completely within it. The length of the braking section is determined (as with the BM1) by the set braking deceleration or the set braking distance.

Selling price: CHF 53.90 RRP CHF 59.50

On order, lead time to be confirmed

BM3 block section module
Lenz Elektronik 22620
BM3 block section module

The Block Section Module BM3 is a building block that uses ABC technology to slow down and stop trains. It enables prototypical block section operation. The number of blocks is unlimited, as one BM3 is used for each block. The BM3 has a connection for colour light signals to indicate the status: red signal = next block occupied, BM3 set to stop; green signal = next block free, BM3 set to proceed.

Selling price: CHF 62.90 RRP CHF 69.80

On order, lead time to be confirmed

10% off the recommended price
BM3K block section module for reversing loop
Lenz Elektronik 22621
BM3K block section module for reversing loop

A block section equipped with BM3 that runs through a reversing loop requires, in addition to the LK200, a special BM3 module, the BM3K, and two of them. The reason is the reporting line, which consists of only one wire, which is very practical in the "normal case". In this special case, however, the potential is reversed by the reversing loop module, so the reporting via the reporting line would no longer work.

Selling price: CHF 76.90 RRP CHF 85.50

On order, lead time to be confirmed

BMA adapter for BM3 block section module
Lenz Elektronik 22630
BMA adapter for BM3 block section module

The BMA adapter (adapter for the BM3 block section module) enables the connection of signals equipped with a double-coil or motor drive to the BM3 block section module. Technically, the BMA is a relay controlled by the lamp outputs of the BM3. Dimensions: 33 x 19 x 12 mm

Selling price: CHF 26.90 RRP CHF 29.80

On order, lead time to be confirmed

LAN and USB interface
Lenz Elektronik 23151
LAN and USB interface

The Digital plus interface provides an Ethernet connection in addition to the USB interface. This allows the system to be connected to a PC or a router, opening up interesting new possibilities for model railway control. Dimensions: 120 x 60 x 20 mm

Selling price: CHF 177.00 RRP CHF 196.50

On order, lead time to be confirmed

LW150 button module
Lenz Elektronik 25150
LW150 button module

Up to 16 digitally controlled solenoid accessories can be switched with the LW150. Two buttons or a single-pole changeover switch are required for each point/signal (not included in the LW150 supply). Multiple button modules can be used simultaneously, each button module has its own adjustable XpressNet address. Dimensions: 120 x 60 x 20 mm

Selling price: CHF 99.90 RRP CHF 110.80

On order, lead time to be confirmed

SET101 starter set with LZV200 and LH101
Lenz Elektronik 60101
SET101 starter set with LZV200 and LH101

The SET101 consists of the LZV200 central power booster and the LH101 hand controller. You can control locomotives with digital addresses from 1 to 9999, plus one conventional locomotive. To control speed, the LH101 hand controller features a finely graduated, precise rotary control. Up to 68 functions in locomotives can be switched – either momentarily or continuously. Double and multiple traction are easily configured.

Selling price: CHF 420.00 RRP CHF 466.30

On order, lead time to be confirmed

SET101-R starter set with LZV200, LH101-R, LTM101
Lenz Elektronik 60103
SET101-R starter set with LZV200, LH101-R, LTM101

The SET101-R consists of the LZV200 central power booster and the LH101-R wireless hand controller. You can control locomotives with digital addresses from 1 to 9999, plus one conventional locomotive. The hand controller features a finely graduated, precise rotary knob for speed control. Up to 68 functions in locomotives can be switched – either momentarily or continuously. Double and multiple traction are easily configured.

Selling price: CHF 624.00 RRP CHF 693.00

On order, lead time to be confirmed

Starter set with digital operation
Lenz Elektronik 60120
Starter set with digital operation

Starter Digital Set, consisting of the Starter Central Station, Starter Hand Controller and switched-mode power supply. With the Starter Digital you can control up to 4 locomotives independently of each other, activate up to 10 functions in locomotives and digitally switch up to 10 points (or signals). 2 Starter Hand Controllers can be used in parallel. The switched-mode power supply has a typical output current of 4A, guaranteed 3A.

Selling price: CHF 102.00 RRP CHF 113.10

On order, lead time to be confirmed

10% off the recommended price
LY145 32 LEDs including connecting cable for LW150
Lenz Elektronik 80145
LY145 32 LEDs including connecting cable for LW150

The extension set consists of a 20-core connecting cable, 32 yellow LEDs, one red LED, and one green LED.

Selling price: CHF 17.90 RRP CHF 20.00

On order, lead time to be confirmed

10% off the recommended price
Update stick for LZV200 to software version 4.0
Lenz Elektronik 80210
Update stick for LZV200 to software version 4.0

Update stick for updating an LZV200 to software version 4.0 The update procedure is described in the accompanying operating instructions.

Selling price: CHF 81.90 RRP CHF 91.30

On order, lead time to be confirmed

15% off the recommended price
Shuttle Train Automatic Circuit Box
LGB 10345 Scale G
Shuttle Train Automatic Circuit Box

With the automatic shuttle unit, you can have a train shuttle back and forth between two stations. An electronic circuit stops the train at the station and then lets it run back again. Easy to install, with an adjustable dwell time and prototypical gentle starting and braking. For connection to 10-24 V DC. The 10345 is the technically optimised and improved successor to the 10340.

Selling price: CHF 135.15 RRP CHF 159.00

On order, shipped within 10-15 days

14% off the recommended price
Track Contact
LGB 17100 Scale G
Track Contact

With this small contact, you can automatically control your LGB points, signals and other accessories. It is triggered by a locomotive equipped with the LGB 17010 magnet and can easily be clipped into most LGB tracks.

Selling price: CHF 18.70 RRP CHF 21.99

On order, shipped within 10-15 days

14% off the recommended price
Orange/White 2-Conductor Wire, 20 Meters / 65 feet 7 inches
LGB 50130 Scale G
Orange/White 2-Conductor Wire, 20 Meters / 65 feet 7 inches

This cable is designed and colour-coded especially for LGB points and signals. Cross-section: 0.5 mm2, length: 20 m.

Selling price: CHF 25.50 RRP CHF 29.99

On order, shipped within 10-15 days

14% off the recommended price
Wire Terminals, 50 Pieces
LGB 50131 Scale G
Wire Terminals, 50 Pieces

Keep your cable ends from "fraying". Using pliers, you can crimp these ferrules onto all LGB cables with a 0.5 mm2 cross-section.

Selling price: CHF 11.05 RRP CHF 12.99

On order, shipped within 10-15 days

14% off the recommended price
Black/White 2-Conductor Wire, 20 Meters / 65 feet 7 inches
LGB 50140 Scale G
Black/White 2-Conductor Wire, 20 Meters / 65 feet 7 inches

This cable is designed and colour-coded especially for LGB accessories such as control panels and lighting. Cross-section: 0.5 mm2, length: 20 m.

Selling price: CHF 25.50 RRP CHF 29.99

On order, shipped within 10-15 days

14% off the recommended price
Track Feeder Wire Terminals, 2 Pieces
LGB 50161 Scale G
Track Feeder Wire Terminals, 2 Pieces

Make your own track connection cable with the cable length you want. Each terminal is equipped with a screw for fastening to the rail and a socket for connecting the cable. Required for connecting the CS2/CS3 digital central unit, Märklin 60215/60216.

Selling price: CHF 11.05 RRP CHF 12.99

On order, shipped within 10-15 days

14% off the recommended price
Distribution Strip
LGB 50720 Scale G
Distribution Strip

With this practical wiring aid you can connect up to 12 wires at a time. This allows you to connect street lamps or cables for several feeder points. Terminals 1-12 and 13-24 are each electrically connected to one another. Screw terminals make the connections easier. 84 x 42 x 19 mm.

Selling price: CHF 28.90 RRP CHF 33.99

On order, shipped within 10-15 days

15% off the recommended price
Electronic Locomotive Controller, 5 Amps
LGB 51079 Scale G
Electronic Locomotive Controller, 5 Amps

This electronic controller for analogue operation offers state-of-the-art technology with high traction current and modern features for your analogue LGB layout: max. 5 A traction current, for use with the 51095 switched-mode power supply. Very sensitive control and smoothed DC voltage. Adjustable control range: +/- 135° with a zero position in the centre / booster button with programmable acceleration, stop/halt button. LED indicators for stop, overload, ready for operation, and direction of travel. Terminals for cables with a cross-section of up to 1.5 mm2, protection against short circuits. Output: 0-24 V DC voltage. Traction current: max. 5 A. Dimensions 160 x 120 x 95 mm.

Selling price: CHF 199.75 RRP CHF 235.00

On order, shipped within 10-15 days

15% off the recommended price New
EU Switched Mode Power Pack 110 VA IP65
LGB 51085 Scale G
EU Switched Mode Power Pack 110 VA IP65

Prototype Splash-proof 110 VA switched mode power pack, IP 65, with a European plug. 120 volts - 240 volts. Suitable for the 51079 locomotive controller and the CS 2/3 60215, 60216, 60226.

Selling price: CHF 126.65 RRP CHF 149.00

On order, shipped within 10-15 days

14% off the recommended price
36 Watt Switched Mode Power Pack
LGB 51092 Scale G
36 Watt Switched Mode Power Pack

Model Switched-mode power supply, protected against water jets (IP 65), for supplying power to the 51099 controller. Connecting cable to the mains with a Euro plug. Highlights 230V, 36 VA. Euro plug, can be used universally Protected against water jets IP 65

Selling price: CHF 68.00 RRP CHF 79.99

On order, shipped within 10-15 days

14% off the recommended price
Locomotive Controller
LGB 51099 Scale G
Locomotive Controller

Controller for use with the 51092 switched-mode power supply.

Selling price: CHF 59.50 RRP CHF 69.99

On order, shipped within 10-15 days

14% off the recommended price
Connection Wires
LGB 51233 Scale G
Connection Wires

This two-conductor black/white cable is designed for the AC connections on your LGB layout and is colour-coded accordingly. Cross-section 1.5 mm2, length 15 m.

Selling price: CHF 25.50 RRP CHF 29.99

On order, shipped within 10-15 days

14% off the recommended price
Control Box
LGB 51805 Scale G
Control Box

With this versatile control panel you can switch up to four electrical circuits on and off, e.g. electrically separated track blocks or street lamps. Each toggle switch operates one circuit. Depending on your needs, you can connect the control panel to DC or AC power by means of the plugs on the sides. An LED indicates when the control panel is being supplied with power. Colour-coded connections on the back make hooking it up easier. With stickers for marking the switch assignments. 126 x 116 x 66 mm. Replaces item 51800.

Selling price: CHF 76.50 RRP CHF 89.99

On order, shipped within 10-15 days