Electronics
Timepiece without function. Prototypical brass mast with base socket for easy mounting. Height: 5,6 cm.
On order, lead time to be confirmed
Timepiece without function. Prototypical lattice mast with base socket for easy mounting. Maintenance free by LED lighting. Height: 7 cm.
On order, lead time to be confirmed
Timepiece without function. Prototypical lattice mast with base socket for easy mounting. Maintenance free by LED lighting. Height: 11 cm.
On order, lead time to be confirmed
This traffic sign (prescribed direction of the traffic) fits ideally epoch III and early epoch IV. With base socket for easy mounting. Maintenance free by LED lighting. Dimensions: L 0,6 x W 0,8 x H 1,9 cm.
On order, lead time to be confirmed
These LED light strips are suitable for stationary lighting. They consist of flexible material and are coated on their backs with adhesive tape. Thus they can easily be mounted even in bent condition. The LED strips are intended to be used with power modules 5215, 5225 or 5205 or with DC voltages of 18V or higher. The enclosed resistors allow for brightness adjustment.The max. contact load per segment is 25 mA, the load for the total strip must not exceed 190 mA. Operating voltage with serial resistor: 24V =. Incl. connection cable. The light strip equipped with 42 LEDs consists of 7 separable segments and has a total length of approx. 250 mm. Each segment is approx. 35 mm long and has 6 white LEDs (4000K). The segments are connected in parallel.
On order, lead time to be confirmed
The circuit board with 8 white, maintenance free LEDs can be shortened. Constant power supply integrated, prepared for flicker-protection. Uniform illumination by small LED distance can be used in any coach of all manufacturers designed to be equipped with lighting. Suitable for DC, AC or digital power. Maximum power input 30 mA. Dimensions: L 13,2 x W 0,9 cm.
On order, lead time to be confirmed
Pedestrian signal for epochs III – VI. The set contains 4 pedestrian lights, with red and green LEDs, used for pedestrian crosswalks. Prototypical brass mast with base socket for easy mounting. Maintenance free by LED-lighting. The pedestrian signals are useable with traffic lights item 5094 or 5095, which contain the necessary electronic control module. For a full two-street intersection 2 x item 5094 or 2x item 5095 and 1 x item 5096 are required. Height: 4,1 cm.
On order, lead time to be confirmed
One piece Vollmer stone art street is attached. Length: 18 cm. The tunnel portal is made of Vollmer stone art. Dimensions: L 16,7 x W 9,7 x H 2,2 cm.
On order, lead time to be confirmed
These LED light strips are intended solely for stationary lighting applications, such as simulating neon tubes in buildings or at train platforms. They are made from flexible material. The LED strips are designed for operation with the power modules, items 5215, 5225, or 5208, or the LED dimmer, item 5590, or with DC voltages of approx. 18 V and above. The included resistors allow for brightness adjustment. Recommended operating voltage: 24 V DC, total current without series resistor: 9 mA. Connection cable included. The light strip, equipped with 5 warm-white (2200k) LEDs, has a total length of approx. 17 mm.
On order, lead time to be confirmed
These LED light strips are intended solely for stationary lighting applications, such as simulating neon tubes in buildings or at train platforms. They are made from flexible material. The LED strips are designed for operation with the power modules, items 5215, 5225, or 5208, or the LED dimmer, item 5590, or with DC voltages of approx. 18 V and above. The included resistors allow for brightness adjustment. Recommended operating voltage: 24 V DC, total current without series resistor: 9 mA. Connection cable included. The light strip, equipped with 5 white (5700k) LEDs, has a total length of approx. 17 mm.
On order, lead time to be confirmed
Extremely powerful model train transformer to provide lighting of complete model towns and for controlling magnetic components, for safe switching of various magnetic items (even at the same time). Due to the high power, the use of the high current cable item 6896 (brown) and item 6897 (yellow) is necessary to supply electricity. Integrated overload protection avoids overload and short-circuit breakdown by timeous cut-off of the transformer. Technical data: Input voltage 230 V ~,output voltage 9 and 16 V~, maximum power 150 VA. Dimensions: L 17,9 x W 8,9 x H 8,1 cm.
On order, lead time to be confirmed
Integrated light signal control by prototypical smooth signal pictures. Full automatic and semi-automatic modes are available, in semi-automatic mode the train is started manually with a button. Current situation is shown by 2 LEDs. External power supply, transformer, is required. Provided for analogue locomotives, but limited operation with digital locomotives is possible. This item is not suitable for Märklin metal track. Please contact our customer service.
On order, lead time to be confirmed
To control and support 8 track sections. The outputs can be mounted directly to insulated track sections and detect every consuming vehicle. Suitable for AC- and DC digital voltage. Feedback decoders e. g. item 5217, relays items 5207, 5551, 5552, points and signals with end sections, LEDs or lamps can be connected. Max. load is 3 A for the outputs and 4,5 A for the whole module. Track occupancy detector provides a special track supply, which provides feedback even if the current on the rails is interrupted (trafo reset to zero or after short circuit).
On order, lead time to be confirmed
For time-triggered operations, e.g. blinking lights, or simulation of train driver’s reaction time after setting a signal to green. Delays for switching on or off are separately adjustable between 0 and 3 minutes. Two simultaneously switching outputs are available, so you can use it for a signal and a train at the same time. Contact load max. current: 2 A each output.
On order, lead time to be confirmed
Suitable to connect all scales of Viessmann standard colour light signals. With this module you can control the aspects of colour light signals without using relays. Optional connection of one signal with more aspects or two signals with 3 aspects. Special technology allows prototypical smooth changing of the signal lights. Optional blanking (distant signal switched off while main signal on the same mast shows “stop” position). One control module replaces up to 7 relays which are required with conventional technology. Without train control, so best used with computer-controlled digital layouts. Controlled by push-button panels items 5546 or 5547, single switch, track contacts or digital decoders are possible.
On order, lead time to be confirmed
Decoder to switch continuous current for colour light signals, lighting, motors, track or accessories. Compatible with Viessmann Commander, Märklin Digital and Uhlenbrock Intellibox. The switches for the setting of 80 possible addresses are accessible from the outside. It has 4 separate and independently controlled relays, max. current 2 A each. Supports both external supply and supply from the digital track.
On order, lead time to be confirmed
Easy connection (only 4 cables). Current situation is shown by 4 LEDs. No regulated transformer required. Connection to 10 – 16 V AC voltage or 14 – 22 V DC. The output is DC, so it is not suitable for AC (Märklin) or digital locomotives.
On order, lead time to be confirmed
Compatible with the s88. The feedback decoder can be used with the Märklin Interface, the Märklin Memory, Uhlenbrock Intellibox and Viessmann Commander. The 16 inputs of the module for track occupancy detection or for starting memory-switch sequences can be connected to the track contacts item 6840 or with Märklin K-and C-tracks directly to the contacts track section. Attached is a 15 cm length special cable and original s88 plugs. For 2 rail tracks the track occupancy detector item 5233 is recommended.
On order, lead time to be confirmed
Useable in connection with control modules for colour light signals items 5221 – 5223 and hobby light signals, item 4021, 4022. The module offers 3 possible distant signal aspects (Vr0, Vr1 and Vr2). Authentic smooth switch of signal aspects. By masking the stop showing home signal fixed on the same mast the distant signal is switched off.
On order, lead time to be confirmed
Useable for all 2-aspect colour light main signals (block signals) and light block signals with LED lighting scale 0 up to Z (except signals with multiplex-technology). The module provides the block signal aspects Hp0 and Hp1. Authentic smooth switch of signal aspects. Integrated contact for train control. With stop showing signal the track in front of the signal is switched off. Control by universal push-button panel item 5547, single button, switching tracks, track contacts or digital magnet decoder. Additional output to control distant signal by control module item 5220.
On order, lead time to be confirmed
Useable for all 3-aspect colour light entry signals scale 0 to Z (except signals with multiplex-technology). The module provides all 3 entry signal aspects (Hp0, Hp1 and Hp2). Authentic smooth switch of signal aspects. Integrated contact for train control. With stop showing signal the track in front of the signal is switched off. Control by universal push-button panel item 5546, single button, switching tracks, track contacts or digital magnet decoder. Additional output to control distant signal by control module item 5220.
On order, lead time to be confirmed
Useable for all 4-aspect colour light departure signals scale 0 to Z (except signals with multiplex-technology). The module provides all 4 block signal aspects (Hp0, Hp1, Hp2 and Sh1). Authentic smooth switch of signal aspects. Integrated contact for train control. By stop showing signal the track in front of the signal is switched off. Control by universal push-button panel item 5545, single button, switching tracks, track contacts or digital magnet decoder. Additional output to control distant signal by control module item 5220.
On order, lead time to be confirmed
The module offers an integrated digital decoder (Märklin-Motorola, NMRA-DCC) and is used to control 2 colour light signals (one home signal and one distant signal) with LEDs and a common plus pole or bulbs, provided they do not draw more than 200 mA in total. Therefore, it is suitable for all signal scales 0 up to Z (except for the Viessmann signals with multiplex-technology). It can be activated in conventional mode via the push-button panels items 5545, 5546 and 5547 or via a digital signal. It is equipped with Viessmann Signalbus and can be configured for the following applications: 2 or several aspect colour light signal: A 2-aspect home signal with the aspects proceed and stop requires the push-button panel item 5547 (for 4 signals) or a digital address. A signal with 3 or 4 aspects with the additional aspects proceed slowly and shunting permitted requires the push-button panel item 5546 (3-aspect, 2 signals) resp. item 5545 (4-aspect, 2 signals) resp. a digital operation 2-aspect. Distant signal or block signal: When configured as a block signal the module responds automatically to the status of the corresponding track sector. This works only in conjunction with track occupancy detectors with continuous output. Per signal sector up to 2 track sectors are required. In this mode the module changes automatically to proceed if the following sector is clear (unoccupied). If one of the two sectors is occupied, the module switches to stop. Own distant signal or distant signal on the same mast: The signal module controls the main signal and the corresponding distant signal or the distant signal of a following main signal mounted on the same mast. In that case the distant signal will show the dark aspect when the main signal shows stop. Interrupt track supply or switch on brake generator when stop aspect is shown: With the relay for automatic train control item 5228 the module can stop trains automatically either by interrupting the track voltage in front of the signal or – more prototypical – with the digital brake module item 5232 (Märklin Motorola) or a brake generator (for NMRA DCC). This makes it possible in both analogue and digital mode to control the track by sections. Signal with aspects stop and proceed slowly: If required you can configure the module to permit these two aspects only. In that case the module can be activated via the push-button panel item 5547 or a digital address. Regardless if the module is triggered by push buttons or track contacts the logic always assures that the red button has preference if two or more devices provide conflicting commands.
On order, lead time to be confirmed
The ideal solution for stable and powerful switching current as well as bright and flicker-free LED-lighting. To increase the switching power of digital decoders with separate voltage feed. For connection to the decoders items 5211, 5231, 5280 and 5285 and digital signals. Suitable for all decoders even from other producers in case an external power supply input is offered. One power module is able supply to 200 LED lights or several decoders. Power rating: 5A. Protected against overload, a green LED indicates the readiness for operation.
On order, lead time to be confirmed