Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Decoders

Filter products
14% off the recommended price
Märklin mSD3 SoundDecoderDiesel Locomotive Sounds
Märklin 60978 Scale H0
Märklin mSD3 SoundDecoderDiesel Locomotive Sounds

For converting Märklin/Trix H0 Hobby locomotives of the 36 series. The märklin SoundDecoder mSD3 has a 21-pin 21mtc interface (to NEM 660) and a matching interface board for bogie locomotives of the 36 series. The märklin SoundDecoder mSD3 supports the mfx, MM1, MM2 and DCC digital formats. Preset sound of a diesel locomotive (Herkules).

Selling price: CHF 107.00 RRP CHF 125.00

In stock: 2 on the shelf, shipped within 1-3 days

14% off the recommended price
Märklin mSD3 SoundDecoderElectric Locomotive Sounds
Märklin 60979 Scale H0
Märklin mSD3 SoundDecoderElectric Locomotive Sounds

For converting Märklin/Trix H0 Hobby locomotives of the 36 series. The märklin SoundDecoder3 has a 21-pin interface and a matching interface board for bogie locomotives of the 36 series. The märklin SoundDecoder3 supports the mfx, MM 1, MM2 and DCC digital formats. Preset sound of an electric locomotive (TRAXX).

Selling price: CHF 107.00 RRP CHF 125.00

In stock: 2 on the shelf, shipped within 1-3 days

14% off the recommended price
Märklin mSD3 SoundDecoderNEM 652 Diesel Locomotive Sounds
Märklin 60986 Scale H0
Märklin mSD3 SoundDecoderNEM 652 Diesel Locomotive Sounds

For converting Märklin/Trix H0 locomotives with a built-in high-efficiency motor or other DC motors. The märklin SoundDecoder3 has a soldered-on wiring harness with an 8-pin NEM interface plug, for retrofitting many locomotives with a corresponding NEM interface and locomotives with limited space. The märklin SoundDecoder3 supports the mfx, MM1, MM2 and DCC digital formats. Preset sound of a diesel locomotive.

Selling price: CHF 107.00 RRP CHF 125.00

In stock: 2 on the shelf, shipped within 1-3 days

14% off the recommended price
Installation Digital Decoder for Turnouts (C Track)
Märklin 74466 Scale H0
Installation Digital Decoder for Turnouts (C Track)

Can be retrofitted to the C track three-way point (24630) with an electric point motor. Digital formats mfx, Motorola, and DCC. Connection by means of plug contacts, for Märklin and Trix C track three-way points. The address can be set both with the coding switch (MM 1–320, DCC 1–511) and via CV (MM 1–320, DCC 1–2044) using the programming track. A point lantern can also be controlled; soldering skills are required for this connection. A digital decoder can be fitted to the electric point motor at the same time or later. The decoder is simply connected with plug contacts and can be addressed individually for each point. The digital power supply can be taken directly from the traction current contact on the point. In this way you get a ready-made digital point that is immediately operational even on portable layouts.

Selling price: CHF 48.90 RRP CHF 56.99

In stock: 2 on the shelf, shipped within 1-3 days

11% off the recommended price
Digital Installation Double Slip Switch Decoder (C Track)
Märklin 74467 Scale H0
Digital Installation Double Slip Switch Decoder (C Track)

For retrofitting a slim C track double slip point 24720 or Trix 62720. Digital formats mfx, Motorola, and DCC. Connection by means of plug contacts. The address can be set both with the coding switch (MM 1–320, DCC 1–511) and via CV (MM 1–320, DCC 1–2044) using a programming track. A 74477 point lantern (not included in the contents supplied) can also be controlled.

Selling price: CHF 38.90 RRP CHF 43.99

In stock: 2 on the shelf, shipped within 1-3 days

13% off the recommended price
Decoder Plux16
Roco 10895
Decoder Plux16

Suitable for Gauge H0 and TT. The decoder is equipped with the RailCom function. Maximum motor current: 1.0 A. For further technical data see data sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. Answers to possible questions can be found in this Zimo manual

Selling price: CHF 38.90 RRP CHF 44.90

In stock: 2 on the shelf, shipped within 1-3 days

10% off the recommended price
Servo decoder
Uhlenbrock 67800
Servo decoder

Via simple button programming, the address, end stops, and rotation speed for each servo can be set separately using Motorola and DCC command stations.

Selling price: CHF 34.90 RRP CHF 39.10

In stock: 2 on the shelf, shipped within 1-3 days

Function decoder Basic
Viessmann
Function decoder Basic

Function decoder without sound, usable regardless of gauge. 2 function outputs, up to 100 mA each Effects: dimming, flashing, direction-dependent switching DCC and Motorola protocols with automatic detection Can supplement a locomotive decoder without RailCom as a RailCom transmitter Addresses: DCC up to 10239, Motorola up to 255 Dimensions: 12.5 × 9.5 × 3.3 mm

Regular price: CHF 19.40

In stock: 2 on the shelf, shipped within 1-3 days

H0/TT load-regulated locomotive decoder, NEM 652
Viessmann
H0/TT load-regulated locomotive decoder, NEM 652

Load-regulated locomotive decoder without sound for H0 and TT gauge. NEM 652 interface (8-pin) DCC (NMRA) and Märklin Motorola protocols (old and new) Short and long addresses up to 10239, 14, 28 or 128 speed steps Motor current up to 1.1 A, total load 1.2 A in digital operation 2 light outputs (150 mA each, dimmable) and 2 function outputs (300 mA each) Short-circuit protection Dimensions: approx. 24.6 × 14.0 × 2.9 mm

Regular price: CHF 24.90

In stock: 2 on the shelf, shipped within 1-3 days

8-fold point decoder for solenoid point motors
YaMoRC YD8008
8-fold point decoder for solenoid point motors

Specially designed to cope with, high-current, solenoid point-motors, the YD8008 is our 8-fold solenoid decoder with intelligent CDU. It presents the following features: - Eight independent 9.5Amp solenoid outputs - Smart, 9400 uF CDU, monitoring charge levels for safe and powerful switching - Only 380 mA power consumption during charging - Very simple basic-setup (base address), by pressing the programming button and switching the desired turnout address - No complicated CV settings. - Clear-text configuration based upon our new ES-Link technology. With our YD9101-Config or YD7100-Command, configuration can be done via built-in web interface. No need for PC-software or Phone/Tablet Apps ! - or - when using the classic Windows PC interface, the YD9100 config-USB-stick as well as our YD6016LN can provide the configuration. - Eight address to output mappings, each mapping can a free choice address which can switch any and every output - Sequential output activation based upon pulse time and CDU charge level. - CDU startup delay adjustable to prevent tripping short circuit protection in boosters - Very modest power supply requirements. Even for SEEP/Gaugemaster motors a 15V/500mA wall wart is more than enough. - Not suitable for motorized point motors. For these motors, use our YD8116. This also counts for MTB point motors. - For two-wire solenoid motors, like Kato, adapter YD6940 should be used.

Regular price: CHF 68.00

In stock: 2 on the shelf, shipped within 1-3 days

SwitchPilot Extension 4 Relay Outputs Extension for SwitchPilot V1.0
ESU 51801
SwitchPilot Extension 4 Relay Outputs Extension for SwitchPilot V1.0

SwitchPilot Extension, 4 twin-relays (DPDT) output, 2A each, extension for Switch Pilot Family If required, SwitchPilot can be augmented with the SwitchPilot Extension Modul: Plugged in at the side of the SwitchPilot, it offers four relay-driven outputs, used for switching potential-free loads, or for polarizing the frog; the ideal supplement for tricky circuitry. Modes of operation The SwitchPilot Extension Modul only works in conjunction with a SwitchPilot. Plugged in at the side, it gets its electrical power directly from the SwitchPilot. It contains a total of 4 Twin-Relays (2 x DPDT), of which each is dedicated to a pair of transistorized SwitchPilot outputs. The respective relay’s switch position is directly dependent upon the state of this pair of outputs. With the relay’s help, loads can be switched, galvanically separated from the rest of the track (it functions like a k84), or a motorized turnout can be polarized. With the relay’s 1.5 Amp continuous rating, either frogs can be polarized-, or blocks powered signal dependent, or motorized devices, such as (water) pumps may be switched. Especially intricate is the option to control motorized turnouts: Of course the SwitchPilot Extension Module easily handles the necessary motor polarization as well.

Selling price: CHF 37.90 RRP CHF 39.90

In stock: 1 on the shelf, shipped within 1-3 days

SwitchPilot 3 Servo 8-channel DCC/MM OLED RC-Feedback
ESU 51832
SwitchPilot 3 Servo 8-channel DCC/MM OLED RC-Feedback

SwitchPilot 3 Servo, 8x servo decoder, DCC/MM, OLED, with RC-Feedback, updatable SwitchPilot 3 servo decoders are optimized for stationary use on your system and can control up to eight RC servo drives. In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 Servo has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons. Modes The SwitchPilot 3 servo is multi-protocol and can be used with workstations according to the Märklin® Motorola® system (e.g. 6021, Central Station® or Mobile Station®) as well as DCC-enabled central. The configuration can take place on both the main track and the programming track. Thanks to RailCom®, CVs can also be read out. Functioning The SwitchPilot 3 servo can be supplied directly from the digital system or an external DC or AC voltage source. The SwitchPilot 3 servo has eight outputs for the control of RC servo drives. In doing so, it can control these drives so precisely that, in addition to switching switches, any other slow movement sequences can be controlled. The SwitchPilot 3 servo has a built-in power-on pulse suppression to eliminate or reduce the system-related "twitching" of RC servos when applying the supply voltage. Furthermore, the power supply to the servo can be interrupted to prevent a "hum" of some inexpensive servos. Each of the eight servos can be operated either in "digital mode" or in the "proportional mode" introduced for the first time with the SwitchPilot 3 servo: In digital mode, the servo can start two end positions "A" and "B", depending on the switching position on the control panel. The position of the two end positions as well as the speed at which thethe servo moves in the desired direction, can be individually set on the SwitchPilot 3 servo. The digital mode is perfect for switching switches or signals that should always remain in a fixed position. In proportional mode, the servo can move and stop in any position within the end positions "A" and B. The servo only runs as long as the control panel sends a command. If you release the button, the servo stops. In this way, a servo can be stopped in any desired position. The servo speed can be adjusted individually. The proportional mode is ideal for (water) cranes or engine shed gates or any other application, for which intermediate positions are also required. For each servo, in addition to the end positions and the rotational speeds, it can be determined whether it should rock up when reaching the final position. Furthermore, the generation of the servo pulse can be influenced to adapt to the different RC servos on the market or the power supply of each servo can be switched off individually. In this way, cheap so-called so-called Analog servos as well as modern digital servos (with microcontroller) optimally controlled. Analogue Operation The SwitchPilot 3 servo can be used as a special feature without a digital control panel: On request, up to 16 buttons can be connected for direct switching of the servos. Set The SwitchPilot 3 servo can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom® CVs. On request, he also learns the addresses directly via a programming button. The setting is, of course, the simplest with the integrated OLED displays as well as the three input buttons: All (!) Settings can be checked directly on the decoder and changed on request. "Programming" with the help of your headquarters is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 servo are protected against overload. We want you to enjoy your decoder for as long as possible.

Selling price: CHF 61.65 RRP CHF 64.90

In stock: 1 on the shelf, shipped within 1-3 days

18-pin Next18 to NEM651 6-pin adapter cable
ESU 51994
18-pin Next18 to NEM651 6-pin adapter cable

Adapter cable, 18-pin Next-18 socket to NEM651 6-pin, Flex, 88mm, with heat shrink tube Sometimes, the locomotive is still equipped with an "old" 6-pin interface compliant with NEM 651. Using this flexible PCB, which can be folded and cut to length almost at will, you can easily install a modern decoder with a Next18 interface. The adapter board comes with heat-shrink tubing. Art.No. Delivery 51994 Adapter cable, 18-pin Next-18 socket to NEM651 6-pin, Flex, 88mm, with heat shrink tube

Regular price: CHF 6.40

In stock: 1 on the shelf, shipped within 1-3 days

18-pin Next18 to NEM652 8-pin adapter cable
ESU 51995
18-pin Next18 to NEM652 8-pin adapter cable

Adapter cable, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube Due to space constraints, some HO locomotives with the "old" 8-pin NEM-652 interface cannot accommodate a standard HO decoder. With the help of this flexible PCB, which can be folded and cut to length as needed, you can install a modern, compact N-scale decoder featuring a Next18 interface. The adapter board comes with heat-shrink tubing. Art.No. Delivery 51995 Adapter cable, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube

Regular price: CHF 6.40

In stock: 1 on the shelf, shipped within 1-3 days

18-pin Next18 to PluX16 adapter cable
ESU 51996
18-pin Next18 to PluX16 adapter cable

Adapter board, Next18 socket to Plux16 Some N or TT scale models are equipped with a PluX16 interface. This adapter board is suitable for installing a LokSound 5 micro or LokPilot 5 micro in such models; simply plug it in between the locomotive and the vehicle to use a decoder with a Next18 interface. Please take the installation depth and available space into account. Art.No. Delivery 51996 Adapter board, Next18 socket to Plux16

Regular price: CHF 6.40

In stock: 1 on the shelf, shipped within 1-3 days

LokSound 5 micro DCC Direct Kato Japan N
ESU 58731
LokSound 5 micro DCC Direct Kato Japan N

LokSound 5 micro DCC Direct Kato Japan »Blank decoder«, gauge: N The LokSound 5 micro DCC Direct Kato Japan has been specially developed for installation in Kato-branded track N vehicles: in many European and Japanese locomotives of this manufacturer, the ser decoder can be installed directly below the engine instead of the analog board installed as standard. Finally, these models can also be easily retrofitted with a LokSound decoder. The LokSound 5 micro DCC Direct Kato Japan with its dimensions of 27.6mm x 14.1mm x 3mm is a pure DCC decoder and comes without a loudspeaker. Modes The LokSound 5 micro DCC Direct Kato Japan is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully to a suitable digital center.It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokSound 5 micro DCC Direct Kato Japan Decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An AUTOMATIC ABC commuter train allows automatic commuting between two stations. The LokSound 5 micro DCC Direct Kato Japan can be used on analog DC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Sound The LokSound 5 micro DCC Direct Kato Japan Decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz and offers hi-fi quality on its system. There is virtually no difference to the original audible anymore. A Class-D audio output with up to 3W output power controls the speakers, which can have between 4 ohms and 32 ohms impedance. A 128 Mbit sound memory provides enough capacity. All individual noises can be adjusted individually in the volume. The super-flexible sound engine without a rigid schedule allows the exemplary simulation of all conceivable rail tracks. Functions Although the LokSound 5 micro DCC Direct Kato Japan is normally installed in the motor car of a drive car set, three reinforced function outputs for lighting are available at their own discretion. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokSound 5 micro DCC Direct Kato Japan has a variable PWM clock frequency from 10kHz to 50kHz, which ensures a super-quiet drive, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokSound 5 micro DCC Direct Kato Japan Decoder delivers up to 0.9A motor power. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 58731 LokSound 5 micro DCC Direct Kato Japan »Blank decoder«, gauge: N

Regular price: CHF 115.00

In stock: 1 on the shelf, shipped within 1-3 days

LokSound 5 Nano DCC single wires 11x15mm N TT
ESU 58923
LokSound 5 Nano DCC single wires 11x15mm N TT

With the LokSound 5 Nano DCC, ESU has succeeded in developing an even smaller LokSound decoder! Thus, it should really be used in all vehicles of nominal sizes N and TT.

Regular price: CHF 115.00

In stock: 1 on the shelf, shipped within 1-3 days

LokPilot 5 Basic 8-Pin NEM652 gauge H0 0
ESU 59020
LokPilot 5 Basic 8-Pin NEM652 gauge H0 0

LokPilot 5 Basic, 8-pin NEM652, Gauge H0, 0 While LokPilot 5 decoders can undoubtedly meet all imaginable requirements of even the most demanding experts, many model railway eras are looking for a robust, high-quality DCC decoder for your standard requirements, which should also be affordable. The LokPilot 5 Basic was developed with the aim of offering a modern decoder with a reasonable range of functions at a reasonable price. The LokPilot 5 Basic comes in two versions: In addition to a version with an 8-pin NEM interface, a version with 21MTC interface is also available. This makes the LokPilot 5 Basic particularly suitable for use in track H0 vehicles. Modes The LokPilot 5 Basic is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 20 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully automatically to a suitable digital center. It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokPilot 5 Basic Decoder detects the Märklin® brake distances as well as the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible.The LokPilot 5 Basic Decoder can be used on analog DC webs. The maximum speed can be set separately.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Basic has 4 reinforced function outputs in each version. In the 21MTC interface, there are 8 logic-level outputs at the interface, two of which are also suitable for controlling servos. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 Basic delivers up to 0.9A continuous current. A variable PWM clock frequency from 10kHz to 50kHz ensures super-quiet operation, especially for bell anchor motors – The typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Basic to bridge dirty rail cuts. Protection Of course, all function outputs as well as the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59020 LokPilot 5 Basic, 8-pin NEM652, Gauge H0, 0 59029 LokPilot 5 Basic, 21MTC NEM660, Gauge H0, 0

Selling price: CHF 27.50 RRP CHF 28.90

In stock: 1 on the shelf, shipped within 1-3 days

LokPilot 5 Fx DCC PluX22 NEMV NEM658 H0 0
ESU 59222
LokPilot 5 Fx DCC PluX22 NEMV NEM658 H0 0

LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 The LokPilot 5 Fx DCC is a function decoder with NO MOTOR CONTROL and is therefore perfect for installation in control cars (Cab Cars) or rail vehicles that only need lights and/or lighting effects. As the "twin brother" of the LokPilot 5 Fx, it shares its features and the basic characteristics of all other LokPilot 5 decoders, but is a pure DCC decoder. The LokPilot 5 Fx DCC is supplied in three versions: In addition to the "classic" version with 8-pin NEM 652 wiring harness, a version for the 21MTC interface and a PluX22 interface is also available. Operating Modes The LokPilot 5 Fx DCC is a pure DCC decoder. 14 to 128 speed steps are as standard as short (1-127) and long (128-9999) addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable command stations such as those from ESU. Auxiliary CVs exist for command stations that can only program the CVs from 1-255. The LokPilot 5 Fx DCC decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An automatic ABC shuttle train system enables automatic shuttle operation between two stations. Although this decoder does not have motor control, it is important for the decoder to be able to synchronize non-motorized rail vehicles with those that are motorized. The LokPilot 5 Fx DCC decoder can be used on analog DC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustments are required. Functions The LokPilot 5 Fx DCC has been equipped with an astonishing number of function outputs. Depending on the interface version, each LokPilot 5 Fx DCC decoder offers at least 10 powered function outputs, each with a max output current of 250mA for lights. Versions with a PluX22 or 21MTC interface also feature 4 outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. Interaction The LokPilot 5 Fx DCC is designed to work with the LokSound 5 and the LokPilot 5 decoders: For example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 decoder and the control car (Cab Car) with a LokPilot 5 Fx DCC. Provided they have the same address, both behave identically. The identical CV arrangement makes it easier to coordinate the two decoders. Operational reliability A PowerPack can be connected to the LokPilot 5 Fx DCC to bridge dirty track sections. Protection The outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Technical Specifications Operating Modes: NMRA/DCC with 14, 28, and 128 speed steps, DCC RailCom® DCC 2-digit and 4-digit addresses (short and long addresses) Analog DC voltage (can be switched off). Automatic detection of operating mode and DCC speed step setting Support for Lenz® LG100, Märklin®, Roco® braking sections, and ZIMO® HLU commands Support for ABC braking mode and ABC shuttle train section Wrong-way bit / saving operating states Shunting mode and acceleration and braking delay can be switched via button Speed ​​controller: NO MOTOR CONTROL Function outputs: 10 powered function outputs Version with 21MTC interface has 2 additional logic level outputs and 2 further logic level outputs instead of SUSI Version with PluX22 interface has 2 logic level outputs instead of SUSI 250mA load capacity per powered output Total current of all function outputs approx. 1500mA. Short-circuit-proof outputs Functional output assignments freely selectable (function mapping) Dimensions: 16.5 mm x 15.5 mm x 4.5 mm Instruction manual Art.No. Delivery 59220 LokPilot 5 Fx DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 59222 LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 59229 LokPilot 5 Fx DCC, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0

Regular price: CHF 26.90

In stock: 1 on the shelf, shipped within 1-3 days

LokPilot 5 DCC, 6-pin NEM651, gauge H0, 0
ESU 59626
LokPilot 5 DCC, 6-pin NEM651, gauge H0, 0

LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl. The decoder accepts all DCC programming modes and thanks to RailCom® the CV values ​​can be read on the main track with RailCom equipped DCC systems. For command stations that only program the CVs from 1-255 auxiliary CV registers exist. The LokPilot 5 DCC decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACKCommands or the Lenz® ABC system. Also braking with DCC brake modules or with DC voltageis possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle trainenables automatic commuting between two train stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The top speedcan be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5DCC packed with function outputs. Depending on the interface version, each LokPilot offers 5 DCCDecoder at least 10 amplified function outputs with 250mA output current each. In the executionswith PluX22 or 21MTC interface there are 4 outputs to control servos orLogic level outputs added. All-important lighting functions are available. The brightness of each outputcan be set separately. The decoder masters automatic pushing and pullingwhen uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 DCC has been fundamentally improved again. A variably adjustablePWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors.Operation - The typical “hum” is a thing of the past. The load control now has up to10 CVs  which can be adjusted for difficult cases. The unique "Autotune" function enablesthe automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to 1.5A of motor current. Enough juice even for older motors. Operational safety On request, a PowerPack can be fitted to the LokPilot 5 DCC to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Analog Gleichspannung (abschaltbar). Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59620 LokPilot 5 DCC, 8-pin NEM652, gauge H0 ,0 59622 LokPilot 5 DCC, PLUX22 NEM658, gauge H0 ,0 59626 LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 59629 LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 59659 LokPilot 5 DCC, 21MTC MKL, gauge H0 ,0

Selling price: CHF 37.90 RRP CHF 38.90

In stock: 1 on the shelf, shipped within 1-3 days

12% off the recommended price
DCC-Decoder 6-pin
Fleischmann 685404
DCC-Decoder 6-pin

Suitable for Gauge H0e, TT and N. The decoder is equipped with the RailCom function. Maximum motor current: 0.8 A. Wire length: approx. 30 mm. For further technical specification, see the spec sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. Answers to possible questions can be found in this Zimo manual

Selling price: CHF 40.90 RRP CHF 46.90

In stock: 1 on the shelf, shipped within 1-3 days

11% off the recommended price
Decoder NEM651
Fleischmann 686101
Decoder NEM651

Suitable for Gauge H0e, TT and N. The decoder is equipped with the RailCom function. Maximum motor current: 0.8 A. For further technical data see data sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. Answers to possible questions can be found in this Zimo manual

Selling price: CHF 36.90 RRP CHF 41.90

In stock: 1 on the shelf, shipped within 1-3 days

DCC decoder without plug (N gauge)
Fleischmann 696859 Scale N
DCC decoder without plug (N gauge)

Digital locomotive decoder to NMRA DCC standard for N gauge, version without plug connector with connecting leads for retrofitting DC locomotives without an interface. Supports 14/28/128 speed steps, function mapping (CV 33/34) and load regulation. Predecessor of the current decoder 69685401.

Regular price: CHF 44.90

In stock: 1 on the shelf, shipped within 1-3 days

Retrofit Sound Decoder
LGB 55029 Scale G
Retrofit Sound Decoder

Model This decoder is suitable for use in digital operation (DCC, mfx) as well as in analogue operation (DC). It can be used to convert all LGB motive power units built from 2014 with the 27-pin interface. Many vehicles with the old 10-pin interface can be converted by means of the 55529 interface adapter. Vehicles without an interface can be converted by means of the included interface board; size of the interface board approx. 65 mm x 40 mm. A speaker box is also included, but other speakers with suitable electrical characteristics can also be connected. Compared to the previous decoder, the performance data have been considerably increased; it also offers considerably more functions and programming options. The decoder can be conveniently programmed and adapted to your individual needs with the Märklin decoder tool (https://www.maerklin.de/de/service/downloads/neu-nachruest-decoder-mld3msd3/mdecodertool-mdt3/). The extensive sound library, which has been specially expanded to include a large number of the well-known LGB models and is constantly being added to, can be accessed via the Internet. Technical data: - Total load capacity max. 10 A, motor output > 4 A - Audio power (sound) 6.7 W/4 Ω - Locomotive address programmable from 1-10239 - 14 or 28 (128) speed levels - Load control adjustable to different locomotive types in analogue and digital operation - Parallel control for all light and function outputs - Programmable blinking light and short-duration functions. These and other functions can be programmed with the Märklin CS 2 and CS 3 central units as well as the Märklin Mobile Station. Highlights Now 32 functions Max. 10 A total current Optimised coasting behaviour Volume of the sounds individually adjustable Calibration function for adapting the motors

Selling price: CHF 182.00 RRP CHF 199.00

In stock: 1 on the shelf, shipped within 1-3 days