Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Decoders

Filter products
Decoder k 83.
Märklin
Decoder k 83.

Receiver for switching points, signals or uncoupling tracks.

Regular price: CHF 18.00

In stock: 1 on the shelf, shipped within 1-3 days

Märklin sound decoder mSD.
Märklin
Märklin sound decoder mSD.

For converting Märklin/Trix H0 hobby locomotives of the 36 series. The Märklin sound decoder has a 21-pin interface and a matching interface board for bogie locomotives of the 36 series. The Märklin sound decoder supports the digital formats mfx, MM 1, MM2 and DCC. Preset sound of an electric locomotive (TRAXX).

Regular price: CHF 79.90

In stock: 1 on the shelf, shipped within 1-3 days

Märklin mSD sound decoder
Märklin
Märklin mSD sound decoder

For converting Märklin/Trix H0 locomotives with a built-in high-performance motor or other DC motors. The Märklin sound decoder has a soldered cable harness with an 8-pin NEM interface plug for retrofitting many locomotives with a corresponding NEM interface and locomotives with space constraints. The Märklin sound decoder supports the digital formats mfx, MM1, MM2 and DCC. Pre-set sound of a diesel locomotive.

Regular price: CHF 99.90

In stock: 1 on the shelf, shipped within 1-3 days

14% off the recommended price
Märklin mSD3 PluX22 SoundDecoder
Märklin 60996 Scale H0
Märklin mSD3 PluX22 SoundDecoder

Model For retrofitting locomotives with a built-in PluX22 interface to NEM 658. The märklin SoundDecoder3 supports the mfx, MM1, MM2, DCC and RailCom® digital formats. Preset sound of a diesel locomotive. Highlights mfx/DCC/RailCom®-capable Full integration into the Märklin digital system Additional physical outputs Märklin's own mapping Note A Märklin 60970 decoder tester is required for programming.

Selling price: CHF 85.90 RRP CHF 99.99

In stock: 1 on the shelf, shipped within 1-3 days

10% off the recommended price
eMOTION XLS sound decoder – RhB Ge 2/4 "Schnupftrückerli"
Massoth 8230045
eMOTION XLS sound decoder – RhB Ge 2/4 "Schnupftrückerli"

The eMOTION XLS has been one of the most popular large-scale sound decoders since its introduction in 2006, thanks to continuous development. With 18 robust screw terminals, the XLS can be used universally. Components such as clock generators, reed contacts, speakers, buffer connections, SUSI, etc., can be practically plugged in once the decoder is installed. With a motor output stage power of up to 3.5 amperes, it is ideally suited for two-motor locomotive models for both digital and analogue operation.

Selling price: CHF 163.00 RRP CHF 181.20

In stock: 1 on the shelf, shipped within 1-3 days

12% off the recommended price
Turnout decoder Geo-Line
Roco 61196 Scale H0
Turnout decoder Geo-Line

Turnout decoder geoLine. Suitable for the turnout drive 61195 of the geoLine track system. Accessible via turnout addresses 1 to 1024. Decoder characteristics can be changed via CVs. Easy assembling Simple operation Safeguarded against overheating and short-circuit fault NOTE: No longer accessible via locomotive addresses!

Selling price: CHF 28.90 RRP CHF 32.90

In stock: 1 on the shelf, shipped within 1-3 days

Locomotive decoder 2000 mA for NEM interface
Trix 66837
Locomotive decoder 2000 mA for NEM interface

Decoder for all DC locomotives with a current consumption of up to 2000 mA (motor 2000 mA, lighting 300 mA). Suitable for digital locomotives with an 8-pin digital interface to NEM. Universally usable in Selectrix and DCC format. Automatic system and analogue detection. Same locomotive address in Selectrix and DCC operation. 7 adjustable maximum speeds. 4 adjustable motor pulse variants. Automatic load compensation. Connection for lighting function. Connection for additional function. 4-pin SUSI interface for further special functions in DCC operation. Short-circuit protection of the motor output. Overload protection of the lighting output. Overload protection of the additional function. Programming of additional settings by selecting address "00", e.g. fine graduation of the pulse widths (control variant), polarity reversal of the direction of travel in Selectrix operation: 31 speed steps. 111 addresses. Block section operation with simple diodes (1 or 2 stopping sections). Braking mode with brake diode. in DCC operation: Manual speed step selection 14/28 steps. Automatic switchover to 128 speed steps. Addresses optionally 7-bit or 14-bit. Braking mode with DC voltage and "broadcast-mode" braking generators Dimensions approx. 24.2 x 15.4 x 3.9 mm.

Regular price: CHF 10.00

In stock: 1 on the shelf, shipped within 1-3 days

ID2 N-TT decoder, 6-pole
Uhlenbrock 73310
ID2 N-TT decoder, 6-pole

The standard decoders for small gauges are the 73xxx series. These decoders are available with connecting wires (73300), with 6-pin plug to NEM 651 (73310) and with PluX12 interface (73340). This can be used, for example, to equip Tillig locomotives. The highlight is the 73236 decoder for locomotives with the Next18 interface. It is even fitted with the Intellimatic. Our new 73406 decoders with connecting wires and 73416 with 6-pin plug to NEM 651 are intended for the smallest locomotives. They are distinguished by a very small size while achieving high performance. Thanks to the built-in protection mechanisms, these decoders are extremely robust even at this small size. All IntelliDrive 2 decoders have RailComPlus®, Selectrix®, ABC braking and extended function mapping, and can be updated on the track. For easy plugging in of a sound module, the decoders are fitted with a SUSI or microSUSI interface. On the Next18 decoder, the SUSI connections are found on the connector strip. Together with the IntelliSound-microModul or IntelliSound-kompaktModul, an extremely small decoder-sound combination results. Art. no. 73310 Decoder, microSUSI, Multi, DC, control, wire

Selling price: CHF 27.90 RRP CHF 30.60

In stock: 1 on the shelf, shipped within 1-3 days

10% off the recommended price
AnDi, motor, AC
Uhlenbrock 75000
AnDi, motor, AC

The digital decoder is the brain of your locomotive. It determines the running characteristics and switching options. A poorly chosen decoder can quickly spoil your enjoyment of the vehicle. IntelliDrive decoders are at the forefront of technology and guarantee you optimal running characteristics.

Selling price: CHF 22.90 RRP CHF 25.50

In stock: 1 on the shelf, shipped within 1-3 days

Load-regulated mini locomotive decoder for DCC and Selectrix, NEM 651
Viessmann
Load-regulated mini locomotive decoder for DCC and Selectrix, NEM 651

Very small and flat load-regulated locomotive decoder without sound for DCC and Selectrix. 6-pin flat cable for direct connection to the NEM 651 interface Motor output 1 A, 2 light outputs (300 mA each), 1 function output (50 mA) Dimensions: 13.8 × 9 × 1.8 mm

Regular price: CHF 71.90

In stock: 1 on the shelf, shipped within 1-3 days

Servo drive with plastic gear. With microcontroller. 30 cm cable harness. Fixing material.
ESU 51804
Servo drive with plastic gear. With microcontroller. 30 cm cable harness. Fixing material.

Servo Motor, precision mini-servo, micro-controlled with plastic gearing, incl. mounting kit The Precision Servo Motor is a high-performance and noiseless actuator, introduced by ESU, suitable for the SwitchPilot decoders. It uses a highly-developed remote control (RC) technique and is perfectly suited for setting in motion all kinds of scenes on your layout. ESU has put all the experience gained with the previous servo motor into the new Precision version, which is better than other servo products, to offer a solution for all the demands of model railroaders. Applications The most important application regarding the Precision Servo Motor is to throw points. With the help of the Precision Servo Motor you are able to move your model railway switches like the original ones: the switch blade moves slowly and powerfully from one position to another. While doing this the Precision Servo motor works almost noiselessly due to the precision gearing made of long-lasting plastic. It is mere child´s play to motorize railway crossings via the Precision Servo motor and the SwitchPilot Servo. At last you can let the gates down at your keyboard in due time. Furthermore the Servo motor enables you to open and close the doors of your engine shed by remote control. Thanks to its new electronics the ESU Precision Servo Motor moves considerably smoother than other servos, as the ESU product has been optimized for slow motions. Mini servo The most important component of the Precision Servo Motor is a tiny, 9-gram-light mini servo which has been specially developed and optimized for all demands of a model railway layout. Despite its small dimensions of only 26 mm x 13 mm x 24 mm, it reaches a power of up to 1.0 kg/cm. Its cable length of 30cm (almost twice as long as cables of other standard servos on the market) allows for a longer distance between the servo motor and decoder. Beyond that, an electronic processor-controlled servo enables a precise heading for the required position without bucking - very important for garage doors. The closed current requirements of the electronics have been mottled compared to the previous servo motor which preserves the decoder. However, one of the most important improvements of the new Precision Servo Motor has to do with the switching-on: The well-known tremor when switching on the layout, which occurs with a lot of conventional RC-servos, is 100% choked during every operation mode. You will hear absolutely nothing from the servo when switching your layout on, no railway crossing will bounce. To make the application of the Servo motor as easy as possible, we include substantial accessories with delivery, which are especially adjusted to our customers´ needs: among some, diverse control horns, there is a special servo horn for a direct insert of the controlling wire. The controlling wire is, of course, included as well as the mounting screws. The most important accessory is a special servo holder: it enables you to install the Servo Motor either horizontally or vertically - depending on the application. Art.No. 51804 Servo Motor, precision mini-servo, micro-controlled with plastic gearing, incl. mounting kit

Selling price: CHF 17.90 RRP CHF 18.90

On order, shipped within 4-5 days

SwitchPilot extension adapter set for ABC braking section, 2 pcs. for a total of 4 braking sections
ESU 51808
SwitchPilot extension adapter set for ABC braking section, 2 pcs. for a total of 4 braking sections

SwitchPilot Extension Adapter for ABC brake sections. Set of 2 for 4 brake sections These adaptor boards greatly simplify set-up and wiring of ABC braking sections. They are simply plugged into the terminals of a SwitchPilot Extension. Every adaptor board can generate the signals for two braking sectors and are wired as shown in the picture. ABC braking works reliably with all ESU V4 decoders (and others) and facilitates not just a prototypical slow down ahead of a red signal but also allows for triggering functions while waiting for the signal aspect to change. Any sound effects are also maintained.

Selling price: CHF 15.90 RRP CHF 16.90

On order, shipped within 4-5 days

SwitchPilot adapter set for signals with a common cathode, 2 pcs, with a total of 8 outputs. Cathode
ESU 51809
SwitchPilot adapter set for signals with a common cathode, 2 pcs, with a total of 8 outputs. Cathode

SwitchPilot Adapter for Signals with common cathode. Set of 2 for 8 Outputs Our SwitchPilot decoders cannot only control point mechanisms but also daylight signals. Most modern signals are equipped with LEDs. Usually the anode connections of multi-aspect signals are combined in order to reduce the number of wires. Some manufacturers (e.g.: Viessmann®) combine the cathodes and for that reason these signals could not be controlled with the SwitchPilot in the past. Our new adapter provides the solution. Simply plug the adapter into the output terminals of the SwitchPilot and you are ready to go.

Selling price: CHF 15.90 RRP CHF 16.90

On order, shipped within 4-5 days

3-pin servo extension cable with JR/Futaba plug to socket, 75 cm length
ESU 51810
3-pin servo extension cable with JR/Futaba plug to socket, 75 cm length

Servo Extension Cable, 3-pole J/R plug on socket J/R / Futaba, Length: 75cm With the Servo Extension Cable you are able to lengthen your Precision Servo Motor by up to 75cm. Art.No. 51810 Servo Extension Cable, 3-pole J/R plug on socket J/R / Futaba, Length: 75cm

Selling price: CHF 4.80 RRP CHF 4.90

On order, shipped within 4-5 days

SwitchPilot 3 4-fold DCC/MM OLED RC-Feedback
ESU 51830
SwitchPilot 3 4-fold DCC/MM OLED RC-Feedback

SwitchPilot 3, 4x accessory decoder, DCC/MM, OLED, with RC-Feedback, updatable SwitchPilot 3 decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption.In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons. Modes The SwitchPilot 3 is multi-protocol and can be used with workstations according to the Märklin® Motorola® system (e.g. 6021, Central Station® or Mobile Station®) as well as DCC-enabled control panels. The configuration can take place on both the main track and the programming track. Thanks to RailCom®, CVs can also be read out. Functioning The SwitchPilot 3 can be supplied directly from the digital system or from an external DC or change voltage source. It has a total of 8 transistor outputs, which are grouped in the 4 exit pairs 1 to 4. Each output pair contains two outputs (OutA and OutB) and can be configured individually for the desired use case:In pulse mode, the output is switched on as soon as a switching command is received. The fact that the output automatically switches off again as soon as the time stored in the decoder has elapsed prevents the burning of magnetic article drives.At the moment (K83-compatible) the output remains active as long as the button on the control panel is pressed. This operating mode is suitable for turnout drives with final shutdown or for de-caps.In bi-stable continuous operation (k84-compatible), the two outputs are switched on and off: When pressing the first button (red) on the control panel, the output Out A is switched on. It remains active until pressing the assigned button (green) activates the output Out B of the same output group. Out A and Out B behave like a change switch.In alternating flasher mode, the outputs Out A and Out B of an output pair are switched on alternately with an adjustable flashing frequency. The change indicator is started with the command "Ge- rade/Green" of the assigned button and stopped again with the command "Branching/Red".Optionally, the output can also be slowly dimmed and dimmed (so-called "zoom" for glow lam pen simulation).With the switch 3 mode switch, you can switch all output pairs together to the "k83" or "k84" modes at lightning speed, regardless of how they are configured. Feedback Since the SwitchPilot 3 is RailCom®-capable, all settings can be read out and changed directly in the built-in state on request. In combination with an ECoS as an ideal "partner", the SwitchPilot 3 can record and display the actual turnout setting with appropriately prepared turnout drives. Finally, you have the certainty that your switch has switched correctly! Set The SwitchPilot 3 can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom® CVs. On request, he also learns the addresses directly via a programming button. The easiest way to set is, of course, with the integrated OLED display and the three input buttons: All (!) Settings can be checked directly on the decoder and changed on request. A"Programming" with the help of your control panel is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 are largely protected against overload. We want you to enjoy your decoder for as long as possible.

Selling price: CHF 46.90 RRP CHF 49.90

On order, shipped within 4-5 days

SwitchPilot 3 Plus 8-fold DCC/MM OLED
ESU 51831
SwitchPilot 3 Plus 8-fold DCC/MM OLED

SwitchPilot 3 Plus, 8x accessory decoder, DCC/MM, OLED, updatable SwitchPilot 3 Plus decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption. In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 Plus has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons. Modes The SwitchPilot 3 Plus is multi-protocol and can be used with control panels according to the Märklin® Motorola® system (e.g. 6021, Central Station® or Mobile Station®) as well as DCC-enabled control panels. The configuration can take place on both the main track and the programming track. Thanks to RailCom®, CVs can also be read out. Functioning The SwitchPilot 3 Plus can be supplied directly from the digital system or from an external DC or change voltage source. It has a total of 16 transistor outputs, which are grouped in the 8 exit pairs 1 to 8. Each output pair contains two outputs (OutA and OutB) and can be configured individually for the desired use case: In pulse mode, the output is switched on as soon as a switching command is received. Since the output automatically switches off again as soon as a time stored in the decoder has been reached, a burn-through of magnetic articles is prevented. At the moment (K83-compatible) the output remains active as long as the button on the control panel is pressed. This operating mode is suitable for turnout drives with final shutdown or for de-caps. In bi-stable continuous operation (k84-compatible), the two outputs are switched on and off: When pressing the first button (red) on the control panel, the output Out A is switched on. It remains active until pressing the assigned button (green) activates the output Out B of the same output group. Out A and Out B behave like a change switch.In alternating flasher mode, the outputs Out A and Out B of an output pair are switched on alternately with an adjustable flashing frequency. The change indicator is started with the command "Gerade/Green" of the assigned button and stopped again with the command "Branching/Red".Optionally, the output can also be slowly dimmed and dimmed (so-called "zoom" for incandescent lamp simulation). Set The SwitchPilot 3 Plus can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom® CVs. On request, he also learns the addresses directly via a programming button. The setting is, of course, the simplest with the integrated OLED displays as well as the three input buttons: All (!) Settings can be checked directly on the decoder and changed on request. "Programming" with the help of your headquarters is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 Plus are protected against overload. We want you to enjoy your decoder for as long as possible.

Selling price: CHF 75.90 RRP CHF 82.90

On order, shipped within 4-5 days

SwitchPilot 3 Mini 1-fold solenoid accessory decoder DCC/MM OLED updateable RETAIL packaged
ESU 51834
SwitchPilot 3 Mini 1-fold solenoid accessory decoder DCC/MM OLED updateable RETAIL packaged

SwitchPilot 3 Mini, 1x accessory decoder, DCC/MM, OLED, updatable The compact SwitchPilot 3 Mini decoder is designed for stationary use in hard-to-reach areas of your layout and can control a double-coil turnout motor, two magnetic uncouplers, a two-aspect signal, two incandescent bulbs, or other stationary loads. The SwitchPilot 3 Mini features an innovative operating concept consisting of a 4-line, backlit OLED display and three input buttons. Operating Modes The SwitchPilot 3 Mini is multi-protocol compatible and can be used with command stations based on the Märklin® Motorola® system (e.g., 6021, Central Station®, or Mobile Station®) as well as DCC-compatible control units. Configuration can be performed on either the main track or the programming track. Functions The SwitchPilot 3 Mini can be powered either directly from the digital system or from an external DC or AC power source. It has a total of two transistor outputs. The outputs (OutA and OutB) can be individually configured for the desired application: In pulse mode, the output is switched on as soon as a switching command is received. The fact that the output switches off automatically once the time stored in the decoder has elapsed prevents solenoid drives from burning out. In momentary mode (K83-compatible), the output remains active as long as the button on the control panel is pressed. This operating mode is suitable for accessories with limit switches or for uncoupling tracks. In bistable continuous mode (K84-compatible), the two outputs are switched on and off alternately: Pressing the first button (red) on the control panel switches on output Out A. It remains active until the corresponding button (green) activates output Out B. Out A and Out B behave like a changeover switch. In alternating flashing mode, outputs Out A and Out B are switched on alternately at an adjustable flashing frequency. The alternating flasher is started with the "Straight/Green" command of the assigned button and stopped with the "Round/Red" command. Optionally, the output can also be slowly faded in and out (so-called "zoom" for incandescent bulb simulation). Setup The SwitchPilot 3 Mini can be flexibly set up either on the programming track with DCC command stations or on the main track with POM ("Programming on Main"). It can also learn addresses directly via a programming button. The easiest way to set it up, however, is with the integrated OLED display and the three input buttons: All settings can be checked and changed directly on the decoder. "Programming" using your command station is not required. It really couldn't be simpler. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 Mini are largely protected against overload. We want you to enjoy your decoder for as long as possible.

Selling price: CHF 30.90 RRP CHF 32.90

On order, lead time to be confirmed

SwitchPilot 3 Servo Mini 1-fold servo decoder DCC/MM OLED updateable RETAIL packaged
ESU 51835
SwitchPilot 3 Servo Mini 1-fold servo decoder DCC/MM OLED updateable RETAIL packaged

SwitchPilot 3 Servo Mini, 1x servo decoder, DCC/MM, OLED, updatable The compact SwitchPilot 3 Servo Mini decoder is designed for stationary use in hard-to-reach areas of your layout and can control an RC servo drive. The SwitchPilot 3 Servo Mini features an innovative operating concept consisting of a 4-line, backlit OLED display and three input buttons. Operating Modes The SwitchPilot 3 Servo Mini is multi-protocol compatible and can be used with command stations based on the Märklin® Motorola® system (e.g., 6021, Central Station®, or Mobile Station®) as well as DCC-compatible control units. Configuration can be performed on both the main track and the programming track. Functions The SwitchPilot 3 Servo Mini can be powered either directly from the command station or from an external DC or AC power source. It has an RC servo output. It can control these drives so precisely that, in addition to switching turnouts, it can also control any other slow-moving sequences. The SwitchPilot 3 Servo Mini features built-in power-on pulse suppression to eliminate or reduce the inherent "jerking" of RC servos when power is applied. Furthermore, the power supply to the servo can be disabled to prevent the "humming" sound of some inexpensive servos. The servo can be operated in either "digital mode" or "proportional mode." In digital mode, the servo can move to two end positions, "A" and "B," depending on the switch position on the control panel. The position of these two end positions, as well as the speed at which the servo moves in the desired direction, can be individually adjusted on the SwitchPilot 3 Servo Mini. Digital mode is ideal for switching turnouts or signals that need to remain in a fixed position. In proportional mode, the servo can move to any position within the end positions "A" and "B" and can also stop. The servo only runs as long as the control panel sends a command. Releasing the button stops the servo. This allows you to stop a servo in any desired position. The servo speed can be individually adjusted. Proportional mode is ideal for (water) cranes, locomotive shed doors, or any other application that requires intermediate positions. For each servo, in addition to the end positions and rotation speeds, you can specify whether it should bounce after reaching the end position. Furthermore, to adapt to the various RC servos available on the market, the generation of the servo pulse can be adjusted. This allows for optimal control of inexpensive analog servos as well as modern digital servos (with microcontrollers). Analog Operation The SwitchPilot 3 Servo Mini can be used without a digital command station as a special feature: Two pushbuttons can be added as needed to control the servos directly. Setup The SwitchPilot 3 Servo Mini can be flexibly set up either on the programming track with DCC control units or on the main track with POM ("Programming on Main"). It can also learn addresses directly via a programming button. The easiest way to set it up, however, is with the integrated OLED display and the three input buttons: All settings can be checked and changed directly on the decoder. "Programming" via your control unit is not required. It really couldn't be simpler. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 Servo Mini are largely protected against overload. We want you to enjoy your decoder for as long as possible.

Selling price: CHF 26.90 RRP CHF 28.90

On order, lead time to be confirmed

SwitchPilot signal decoder with 16 independent function outputs, push/pull, removable terminals
ESU 51840
SwitchPilot signal decoder with 16 independent function outputs, push/pull, removable terminals

SignalPilot, accessory decoder with 16 outputs Push/Pull, Removable screw terminals The ESU SignalPilot decoder is a multi-protocol decoder designed primarily for switching daylight signals. It has 16 outputs to which micro lamps or LEDs (with series resistors) can be connected directly. Because all outputs are designed as push/pull output stages, both daylight signals with common anode as well as daylight signals with a common earth connection (common cathode) are suitable, as is the case with Viessmann® signals. Motorised semaphore signals and turnout drives can also be operated with the SignalPilot. Operating modes The SignalPilot supports both DCC with RailComPlus® and Motorola®. Programming allows for each output to be assigned to any address or to a combination of addresses. Functionality The SignalPilot can be powered either directly by the digital command station or by any transformer /power supply unit providing DC or AC. The SignalPilot has 16 transistor outputs in push-pull configuration. Each output can be operated individually as continuous light, flashing light or pulse light. Here, the brightness or flashing frequency can be adjusted as well as fade-in and fade-out times. Various prototypical lighting effects such as soft dimming, fluorescent tube effect, defective fluorescent tube, gas lantern simulation, flicker light ensure a realistic result. Randomly controlled switching on/off as well as an on/off delay can also be activated. A night service extension can dim down the outputs together if so desired. The outputs of the SignalPilot are combined into signal aspects during configuration. In principle, two-, three-, four- or multiaspect signals are conceivable. Depending on the number of outputs involved, one or more turnout numbers (accessory addresses) are assigned to each signal, with the help of which you can later switch the individual signal aspects. Up to 16 turnout numbers are available for this purpose. The configuration of the signal aspects is carried out exclusively with the aid of the ESU LokProgrammer software. You select the desired signal aspects, then write them to the decoder and finally wire the signals as configured. All signal aspects predefined in the LokProgrammer software can be changed individually. The description of the signal aspects themselves is done with the help of XML files, which on the one hand are regularly extended by ESU or can be created and extended by you at your own discretion. In this way, „exotic” signals can also be supported. The SignalPilot is multi-protocol capable and can be used with digital command stations operating the Märklin® Motorola® system (e.g.: 6021, Central Station® or Mobile Station®) as well as DCC enabled command stations. The configuration can be doen by Programming on the Main (POM) and on the programming track. Thanks to RailCom®, CVs can also be read out. Optionally, a SwitchPilot Extension relay module can be docked to the SignalPilot. This facilitates setting up brake chapters or turnout frog polarisation. LokProgrammer The easiest method of configuring the SignalPilot is programming it with the ESU LokProgrammer. Simply choose the desired signal type, and the wiring will be displayed on the screen. Designed with future developments in mind The firmware of the SignalPilot can be updated with the aid of the LokProgrammer at any time. This may be necessary whenever we add new signal types. Art.No. Delivery 51840 SignalPilot, accessory decoder with 16 outputs Push/Pull, Removable screw terminals

Selling price: CHF 75.90 RRP CHF 82.90

On order, shipped within 4-5 days

Adapter board for LokSound XL V4.0
ESU 51971
Adapter board for LokSound XL V4.0

Adapter board for LokSound XL with PIN connectors For professionals in digital model railroading there is a new adapter board. This makes installation easier and safer. First all wires are connected to the soldering points of the adapter board. All contact points (terminals) are present on both - top and bottom.  After that the LokSound XL decoder is plugged on with the multi-pin connector. Finished. Finally you can remove and reinsert your decoder at any time. Art.No. 51971 Adapter board for LokSound XL with PIN connectors

Selling price: CHF 18.90 RRP CHF 19.90

On order, shipped within 4-5 days

LokSound 5 Fx DCC/MM/SX/M4 8-pin NEM652 11x15mm
ESU 58210
LokSound 5 Fx DCC/MM/SX/M4 8-pin NEM652 11x15mm

LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 8-pin NEM652, with loudspeaker 11x15mm, gauge: H0, 0 The LokSound 5 Fx represents a unique feature within the LokSound family: it has NO MOTOR OUTPUT and is specially designed for use in control cars (Cab Cars) or power cars that require sound but lack a motor and thus are not powered themselves. By omitting the motor component, it offers all the sound features of the other LokSound 5 members, yet measures just 21.5mm x 15.5mm. LokSound 5 Fx decoders are offered with an 8-pin NEM652 or 21MTC interface and always come with an 11 x 15 mm "sugar cube" speaker and speaker enclosure kit. Operating Modes Like all family members, the LokSound 5 Fx is a true multi-protocol decoder. It supports the DCC data format as well as Motorola®, Selectrix® and M4. In DCC format, 14, 28, or 128 speed steps are as standard as Short and Long addresses and up to 32 functions. With RailComPlus® technology, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and can be both operated and programmed with compatible digital command stations: Thanks to RailCom®, CV values can be read on the main track with suitable command stations. Auxiliary CVs are available for command stations that can only program the CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses allow the triggering of 16 functions. A built-in programming mode also enables reprogramming with the venerable Control Unit 6021. The M4 protocol allows automatic registration to mfx®-compatible command stations. The LokSound 5 Fx Decoder recognizes the Märklin® brake sections as well as ZIMO® HLU brake commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops when a Selectrix® brake diode is activated. An ABC shuttle train system enables automatic shuttle operation between two stations. The LokSound 5 decoder can be used on analog DC and AC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustment is required. Sound The LokSound 5 Fx decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz, providing hi-fi quality on your layout. There is practically no audible difference from the original recordings. A Class-D audio amplifier with up to 3W output power drives the speakers, which can have an impedance between 4 ohms and 32 ohms. A 128 Mbit sound memory provides sufficient capacity. The volume of all individual sounds can be individually adjusted. The super-flexible sound engine, without a rigid sequence plan, allows for the prototypical simulation of all conceivable rail vehicles. Functions The control car and the power car also have a number of lights to be controlled. Therefore, we equipped the LokSound 5 Fx with 6 powered function outputs for lights. The version with the 21MTC interface has 6 additional outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. NO Motor Control Although the LokSound 5 Fx itself DOES NOT have a motor output, it still "simulates" one. This serves to synchronize with the powered vehicle, where ideally a "full-fledged" LokSound 5 decoder performs its duties. This ensures that the brake squeal occurs simultaneously within a train, or that the lights change direction simultaneously. Operational Safety A PowerPack can be connected to the LokSound 5 Fx to bridge dirty track sections if desired. Protection The outputs are naturally protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 58210 LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 8-pin NEM652, with loudspeaker 11x15mm, gauge: H0, 0 58219 LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 21MTC NEM660, with loudspeaker 11x15mm, gauge: H0, 0

Selling price: CHF 69.90 RRP CHF 74.90

On order, shipped within 4-5 days

LokSound 5 Fx DCC/MM/SX/M4 21MTC NEM660 11x15mm
ESU 58219
LokSound 5 Fx DCC/MM/SX/M4 21MTC NEM660 11x15mm

LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 21MTC NEM660, with loudspeaker 11x15mm, gauge: H0, 0 The LokSound 5 Fx represents a unique feature within the LokSound family: it has NO MOTOR OUTPUT and is specially designed for use in control cars (Cab Cars) or power cars that require sound but lack a motor and thus are not powered themselves. By omitting the motor component, it offers all the sound features of the other LokSound 5 members, yet measures just 21.5mm x 15.5mm. LokSound 5 Fx decoders are offered with an 8-pin NEM652 or 21MTC interface and always come with an 11 x 15 mm "sugar cube" speaker and speaker enclosure kit. Operating Modes Like all family members, the LokSound 5 Fx is a true multi-protocol decoder. It supports the DCC data format as well as Motorola®, Selectrix® and M4. In DCC format, 14, 28, or 128 speed steps are as standard as Short and Long addresses and up to 32 functions. With RailComPlus® technology, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and can be both operated and programmed with compatible digital command stations: Thanks to RailCom®, CV values can be read on the main track with suitable command stations. Auxiliary CVs are available for command stations that can only program the CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses allow the triggering of 16 functions. A built-in programming mode also enables reprogramming with the venerable Control Unit 6021. The M4 protocol allows automatic registration to mfx®-compatible command stations. The LokSound 5 Fx Decoder recognizes the Märklin® brake sections as well as ZIMO® HLU brake commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops when a Selectrix® brake diode is activated. An ABC shuttle train system enables automatic shuttle operation between two stations. The LokSound 5 decoder can be used on analog DC and AC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustment is required. Sound The LokSound 5 Fx decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz, providing hi-fi quality on your layout. There is practically no audible difference from the original recordings. A Class-D audio amplifier with up to 3W output power drives the speakers, which can have an impedance between 4 ohms and 32 ohms. A 128 Mbit sound memory provides sufficient capacity. The volume of all individual sounds can be individually adjusted. The super-flexible sound engine, without a rigid sequence plan, allows for the prototypical simulation of all conceivable rail vehicles. Functions The control car and the power car also have a number of lights to be controlled. Therefore, we equipped the LokSound 5 Fx with 6 powered function outputs for lights. The version with the 21MTC interface has 6 additional outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. NO Motor Control Although the LokSound 5 Fx itself DOES NOT have a motor output, it still "simulates" one. This serves to synchronize with the powered vehicle, where ideally a "full-fledged" LokSound 5 decoder performs its duties. This ensures that the brake squeal occurs simultaneously within a train, or that the lights change direction simultaneously. Operational Safety A PowerPack can be connected to the LokSound 5 Fx to bridge dirty track sections if desired. Protection The outputs are naturally protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 58210 LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 8-pin NEM652, with loudspeaker 11x15mm, gauge: H0, 0 58219 LokSound 5 Fx DCC/MM/SX/M4 »NO MOTOR CONTROL« »Blank decoder«, 21MTC NEM660, with loudspeaker 11x15mm, gauge: H0, 0

Selling price: CHF 65.90 RRP CHF 70.90

On order, shipped within 4-5 days

LokSound 5 L DCC/MM/SX/M4 pin header with adapter
ESU 58315
LokSound 5 L DCC/MM/SX/M4 pin header with adapter

LokSound 5 L DCC/MM/SX/M4 "blank decoder", Pinheader with adapter, gauge: 0 LokSound 5 L is intended for use in all applications where the required power exceeds the limits of LokSound 5. Ideally these are 0 gauge vehicles and also smaller 1 gauge locomotives. Despite its compact dimensions of only 50.8 mm x 25.4 mm x 14 mm it is equipped with a dual speaker output and integral PowerPack. The LokSound 5 is equipped with a multi-pin connector and is supplied ex works with an adapter board featuring solder pads. Operating modes Like all products of the LokSound family the LokSound 5 L is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps and 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Control Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound 5 L decoder supports Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound 5 L will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables automatic commuting between two stations. The LokSound 5 L decoder is also suitable for analogue DC and AC layouts. Sound The LokSound 5 L decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A dual class D audio power amplifier with up to 2-times 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions Every LokSound 5 L decoder has 11 amplified function outputs. On top of that there are another 6 logic outputs, which can, if so desired, control two RC servos or SUSI extension modules. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for the reliable function of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. 4 sensor inputs may be employed in order to trigger functions. Motor control Motor control of the LokSound 5 L has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 L decoder supplies ample current for the motor, namely up to 3.0 A. LokSound 5 L DCC The LokSound 5 L DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Betrieb unter DCC mit RailComPlus®, M4, Motorola® und Selectrix® 32 Funktionen schaltbar (abhängig von der Zentrale) 32-Bit-Prozessor Digitaler Class-„D“-Verstärker mit bis zu 3 W Leistung (LokSound 5 XL: 13 W) Jeder Kanal in 16-Bit-Auflösung und 31250 kHz Samplerate Geräuschspeicher mit 128 Mbit Kapazität Motorregelung mit 50 kHz Taktfrequenz RC-Servos und Susi-Module ansteuerbar 3 neue, individuell einstellbare Bremsregler Zweistufige Schwerlast-Simulation Updatefähig mit ESU-LokProgrammer LokSound 5 L Für die Baugrößen 0 und I Motorstrom 3 A 11 verstärkte Ausgänge für Sonderfunktionen (Total: 17 Ausgänge) Anschlussmöglichkeit für 2 RC-Servos Doppelendstufe zur Ansteuerung von 2 Lautsprechern PowerPack-Speicherkondensator serienmäßig Abmessungen: 50,8 mm x 25.4 mm x 14 mm Schnittstelle Stiftleiste mit Adapter Click the image for a bigger view. Instruction manual Art.No. Delivery 58325 LokSound 5 L DCC "blank decoder", Pinheader with adapter, gauge: 0 Only available at ESU LLC! 58315 LokSound 5 L DCC/MM/SX/M4 "blank decoder", Pinheader with adapter, gauge: 0

Selling price: CHF 165.00 RRP CHF 177.00

On order, shipped within 4-5 days

LokSound 5 DCC/MM/SX/M4 PluX22 speaker 11x15mm
ESU 58412
LokSound 5 DCC/MM/SX/M4 PluX22 speaker 11x15mm

LokSound 5 DCC/MM/SX/M4 "blank decoder", PluX22, with speaker 11x15mm, gauge: 0, H0 The LokSound 5 is the most important member of the LokSound family. Due to the combination of the digital decoder and the sound module on one circuit board we achieve the smallest possible dimensions of 30 mm x 15.5 mm. Therefore it fits into almost any H0 or 0 gauge locomotive. LokSound 5 decoders are available with all popular interface types and are supplied with a sugar cube speaker (11 mm x 15 mm) and a sound enclosure. The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Please note the LokSound 5 DCC decoder does not come with a speaker. Operating modes Like all products of the LokSound family the LokSound 5 is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Central Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound 5 decoder supports the Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables the automatic commuting between two stations. The LokSound 5 decoder is also suitable for analogue DC and AC (!) layouts. Sound The LokSound 5 decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A class D audio power amplifier with up to 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions We are quite aware that you want your locomotives to be as realistic as possible. Therefore we have packed many function outputs into it.  Subject to the type of interface every LokSound 5 has at least 10 amplified outputs. The decoders with PluX22 or 21MTC interface have an additional 4 outputs for controlling servos or as logic outputs. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for reliable operation of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. Motor control Motor control of the LokSound 5 has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 decoder supplies up to 1.5A motor current, which is quite sufficient even for older motor types. LokSound 5 DCC The LokSound 5 DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Betrieb unter DCC mit RailComPlus®, M4, Motorola® und Selectrix® 32 Funktionen schaltbar (abhängig von der Zentrale) 32-Bit-Prozessor Digitaler Class-„D“-Verstärker mit bis zu 3 W Leistung (LokSound 5 XL: 13 W) Jeder Kanal in 16-Bit-Auflösung und 31250 kHz Samplerate Geräuschspeicher mit 128 Mbit Kapazität Motorregelung mit 50 kHz Taktfrequenz RC-Servos und Susi-Module ansteuerbar 3 neue, individuell einstellbare Bremsregler Zweistufige Schwerlast-Simulation Updatefähig mit ESU-LokProgrammer LokSound 5 Universal-Sound-Decoder für die Spurweiten H0 und Spur 0 Motorstrom 1,5 A Je nach Schnittstelle bis zu 12 verstärkte Funktionsausgänge für Sonderfunktionen (Total: Bis zu 15 Ausgänge) 10 Soundkanäle gleichzeitig abspielbar Ab Werk mit 11x15-mm-„Zuckerwürfel“-Lautsprecher mit anpassbarem Schallkapsel-Set PowerPack-Speicherkondensator optional anschließbar Abmessungen: 30 mm x 15,5 mm, Höhe abhängig von Schnittstelle 8-pin NEM 652 PluxX22 6-pin NEM 651 21MTC 21MTC MKL Click the image for a bigger view. Instruction manual Art.No. Delivery 58420 LokSound 5 DCC "blank decoder", 8-pin NEM652, gauge: 0, H0 Only available at ESU LLC! 58429 LokSound 5 DCC "blank decoder", 21MTC NEM660, gauge: 0, H0 Only available at ESU LLC! 58410 LokSound 5 DCC/MM/SX/M4 "blank decoder", 8-pin NEM652, with Speaker 11x15mm, gauge: 0, H0 58412 LokSound 5 DCC/MM/SX/M4 "blank decoder", PluX22, with speaker 11x15mm, gauge: 0, H0 58419 LokSound 5 DCC/MM/SX/M4 "blank decoder", 21MTC NEM660, with speaker 11x15mm, gauge: 0, H0 58449 LokSound 5 DCC/MM/SX/M4 "blank decoder", 21MTC "MKL", with speaker 11x15mm, gauge: 0, H0

Selling price: CHF 92.90 RRP CHF 99.90

On order, lead time to be confirmed