Decoders
Locomotive decoder "SILVER+ Next18" Continuous current rating 600 mA, with interface according to NEM 662, 8 function outputs, ABC, RailCom, dimensions: 15 x 9.5 x 2.9 mm
On order, lead time to be confirmed
The locomotive decoder "SILVER+ 21MTC" has a continuous current rating of 1000 mA, a 21-pin interface, 4 function outputs, ABC, and RailCom. Dimensions: 20.6 x 15.7 x 4.0 mm.
On order, lead time to be confirmed
Locomotive decoder "SILVER+ PluX22" Continuous current rating 750 mA, with NEM 658 interface, 9 function outputs, ABC, RailCom, S.U.S.I. interface, dimensions: 22 x 15 x 6 mm
On order, lead time to be confirmed
Locomotive decoder "Gold+", continuous current rating 1000 mA, 4 function outputs, with NEM652 interface (function outputs 3 and 4 are led out as cables), ABC, USP, RailCom, S.U.S.I. interface, Dimensions: 22.8 x 16.7 x 4.9 mm
On order, lead time to be confirmed
Model Adapter board for plugging the new 55029 large-scale decoder into the Märklin 60971 decoder programmer. Easy connection to a PC/laptop. In addition, the Märklin Decoder Tool software is required, which can be conveniently downloaded from the Märklin homepage (www.maerklin.de under Service/Downloads/Nachrüstdecoder/mLD3/mSD3). It can be used to easily transfer existing or self-recorded sounds; other settings such as maximum speed, braking behaviour, etc. can also be programmed very easily and quickly with it. Note The Märklin 60971 decoder programmer is also required. It is not included.
On order, shipped within 10-15 days
With this point decoder, the control commands for up to four LGB solenoid accessories can be transmitted easily via the tracks. Power is drawn directly from the track, which avoids long, complicated wiring. This point decoder is thus ideal for controlling points and signals out on the line or at more distant locations on your LGB layout. Features: four control outputs / adjustable mode for each output: normal (for points and signals), synchronous blinking (for lamps), asynchronous blinking (for lamps), on/off (for lamps and accessories) / adjustable switching duration for normal, synchronous and asynchronous. Suitable for the CS 2 and CS 3 as well as MZS III. The DCC, mfx and MM formats are supported.
On order, shipped within 10-15 days
Matching the 59079 point motor, this decoder can be used to switch a point digitally. The point decoder is individually addressable (252 addresses) and can be used in the Motorola and DCC format. The switching direction can be swapped (inverted) if desired. It can be programmed with the Central Station 60216 (DCC), 60226 (DCC) or with controllers conforming to the NMRA standard. Size 40 x 27.7 x 13 mm. (H1032-1).
On order, shipped within 10-15 days
Model For quickly testing the new märklin LokDecoder3 and märklin SoundDecoder3 as well as all other decoders that use the following interfaces: NEM 651, NEM 652, MTC14, MTC21 and PluX22. Other decoders, such as those for Gauge 1, LGB or with single wires, are to be connected by means of screw terminals. The other equipment includes:– LED monitoring for the headlights, for Aux 1-6, track input, Aux 3 and 4 amplified and unamplified– Track connection for the digital central unit– Speaker– Motor– Separate connection terminals for another motor– Direct connection to the märklin Decoder Programmer Highlights Easy testing of decoder functions
On order, shipped within 10-15 days
Model For quickly programming the märklin LokDecoder mLD3 and mSD3. Easy connection to your PC/laptop by USB. You need the märklin Decoder Tool software, which you can conveniently download from our website. https://www.maerklin.de/de/service/downloads/neu-nachruest-decoder-mld3msd3/mdecodertool-mdt3 The software helps you to transfer existing sounds or sounds you have recorded yourself quickly and in an easily understandable way. You can now also make all of the other settings very easily, such as maximum speed, braking characteristics, function mapping, etc. IMPORTANT! The factory-fitted decoders in Märklin, Trix and LGB items cannot be edited with this programmer! The programmer works exclusively with the 6097x and 6098x retrofit decoders. Highlights Quick programming of the new märklin decoders mLD3 and mSD3
On order, shipped within 10-15 days
For converting Märklin/Trix H0 locomotives with a built-in high-efficiency motor or other DC motors. The märklin SoundDecoder3 has a 21-pin interface and a matching interface board for retrofitting analogue and digital locomotives. The märklin SoundDecoder3 supports the mfx, MM1, MM2 and DCC digital formats. Preset sound of an electric locomotive. You can find more Märklin explanatory videos at https://www.youtube.com/c/maerklin
On order, shipped within 10-15 days
Powerful 3 amp locomotive decoder with a total load rating of four amps and 8 function outputs, suitable for locomotives with up to two motors. The eMOTION XL locomotive decoder is a high-quality decoder for large-scale and garden railways, for NMRA DCC and all generations of the LGB® MZS. With its various connection options and adjustable special functions, it can drive, among other things, speed-dependent sound module controls or uncoupling drives of the most varied technical designs. Simple function mapping, a freely programmable shunting speed and modern load control for digital and analogue operation (patent pending) round off the range of functions. Of course, analogue or digital operation is recognised automatically. The eMOTION XL locomotive decoder also supports automatic detection between serial (LGB® MZS) and parallel (NMRA DCC) function data processing. The features of the eMOTION XL locomotive decoder at a glance: 14, 28 and 128 speed steps 256 internal speed steps 10239 locomotive addresses programmable speed curve starting, medium and maximum speed (as well as delay times) serial and parallel control for all light and function outputs incl. LGB® P sound updates digital and analogue operation with automatic detection compatible with NMRA DCC and LGB® MZS (all generations) latest-generation load control (for digital and analogue operation) adjustable motor frequency (70Hz – 16 kHz) 3 light connections (front, rear, interior) max. 0.3A each 6 function outputs (all with configurable special functions) max. 0.6A each light and function outputs dimmable and can be activated in analogue mode programmable flashing light, short-time and clock generator functions 2 additional contact inputs for future functions (reserved) shunting speed (with free function mapping) simple function mapping for all function outputs all function outputs freely addressable (F1 to F16) total load rating of 4 amps (motor output stage and function outputs) motor output stage rated for 3 amps (suitable for up to 2 motors of 1.5 amps each) voltage buffer connection integrated for smooth running (accessory: 8151001 or 8151501) overload and temperature protection for the motor and function outputs reset function for all CV values software can be updated CV reading CV writing bitwise CV writing indirect CVs (via register programming for older digital systems) direct register programming (CV 1 – CV4) POM – Program on Main (programming on the main track)
On order, lead time to be confirmed
The Powercap 200 (ex. nano), with its miniature design, is suitable for particularly small, single-motor models, including field railway locomotives, and buffers for a few seconds – enough to get a small locomotive over a dirty section of track. With its minimal size of just 25 x 17 x 15 mm, it can be fitted almost anywhere. The three-core connecting cable (200 mm) can be shortened individually.
On order, lead time to be confirmed
Following the introduction of the Powercap 200, the more powerful Powercap 900 now complements the product range. Despite its compact dimensions of just 30x30x16mm, it is capable of buffering a single-motor locomotive drawing 600mA for up to 6 seconds, and for a considerably longer period when the current consumption is lower. It replaces item 8151601 Powercap micro. Available from October 2024.
On order, lead time to be confirmed
Following the introduction of the Powercap 200 and Powercap 900, the more powerful Powercap 2300 completes the product range. Despite its compact dimensions of just 44x23x32mm, it is able to buffer a two-motor locomotive with 2000mA for up to 12 seconds, and considerably longer with lower current consumption. It replaces 8151701 Powercap maxi. Available from April 2025.
On order, lead time to be confirmed
24.03.2025 – 8151701 is replaced by 8151321 Powercap 2300 The new Powercap maxi replaces the Goldcap buffer 8151501. The size has been reduced by about 40 %. Reserve of up to 30 seconds! The eMOTION Powercap maxi bridges brief interruptions in the track voltage. It was designed especially for twin-motor locomotives. The motor and the special functions are supplied from the storage unit during this interruption. Locomotives can therefore cross common crossings or insulated sections without stopping. The buffering time is up to 30 seconds, depending on the connected load, the current speed and the charge level of the storage unit. Universal digital use & intelligent technology Thanks to its well-thought-out design and the use of special capacitors, the Powercap maxi, with integrated charging circuit and charging function cut-out during decoder programming, is suitable for use with almost all digital decoders that provide the Decoder + and Decoder – contacts directly. (tested with: Massoth, LGB®, Lenz©, Zimo©) Direct connection of the Powercap maxi to decoders of the eMOTION series The Powercap maxi is particularly suitable for connection to decoders of the eMOTION series. The Decoder + (red) and Decoder – (black) contacts are used as usual. The third wire (white) is used to switch off the charging function when the contact is open. This function is handled by a function output of the eMOTION decoder. When the decoder is being programmed or read, the charging function is switched off automatically. The programming procedure can therefore be carried out without any problem. With third-party or older decoders, the switch also included in the delivery is used. The performance data are: Buffering time up to 30 seconds (depending on load) maximum buffer current 3A maximum charging current 400mA Operating voltage 6-20 V DC (max. 24 V)
On order, lead time to be confirmed
The new 10FX servo decoder is an innovative further development of the long-proven and versatile 8FS/8FX decoder generation. It provides sufficient power reserves for controlling up to four servos, two uncouplers or pantograph drives, and other consumers with a wide range of functions, thanks to its ten function outputs suitable for analogue operation, which have a total current capacity of two amperes. Additionally, a voltage buffer is integrated, ensuring smoother operation of the connected servos and uncouplers. With these performance specifications, there is nothing left to desire.
On order, lead time to be confirmed
Compact and powerful DCC function decoder with four reinforced function outputs, each capable of handling a peak load of 1 ampere. The total current capacity is also 1 ampere. The solder connections are located on the underside of the small 25 x 16 mm circuit board. A removable mounting bracket is included. The pack contains two pieces. Available from October 2024.
On order, lead time to be confirmed
Completely newly developed and even more powerful is the new XXL II locomotive decoder, suitable for locomotives with up to 4 motors, with up to 8 amperes of running current and 10 amperes of total current. Highlights: New function mapping, F0-F127, 10 function outputs, 2 servo connections, bus connection for MASSOTH/LGB and SUSI, overload and temperature protection for motor and function outputs. Updatable.
On order, lead time to be confirmed
Universal 1.8 amp locomotive decoder with 8 function outputs, suitable for locomotives with 1 motor. The eMOTION L decoder is a compact locomotive and function decoder, optimally designed for the demands of large-scale operation. In addition to the motor output for single-motor locomotives, it offers up to 8 programmable function outputs. The eMOTION L decoder offers excellent digital and analogue running characteristics. Its good analogue capability is also worth stressing, allowing stable operation from about 7 to 8 volts. With an additional voltage buffer it can do its job even more reliably in analogue and digital operation, and thereby avoids dropouts caused by dirty spots on the track. The features of the eMOTION L locomotive decoder at a glance: locomotive decoder for digital and analogue operation 14, 28 and 128 speed steps motor output rated for 1.8A connection for a model-making servo bus interface for MASSOTH and LGB® modules programmable speed curve starting, medium and maximum speed (as well as delay times) adjustable serial and parallel control for all light and function outputs control of parallel data updates (LGB®) digital and analogue operation with automatic detection compatible with NMRA DCC and LGB® MZS (all generations) latest-generation load control (for digital and analogue operation) adjustable motor frequency (90Hz – 23.5 kHz) 2 light connections (front, rear) max. 0.5A each 6 function outputs (2 of 0.5A each, 4 of 50mA each) light and function outputs dimmable and can be activated in analogue mode programmable flashing light and short-time functions shunting speed and delay times can be switched by function key simple function mapping with direction assignment all function outputs freely addressable (F1 to F16) voltage buffer connection integrated for smooth running (accessory: 8151001 or 8151501) overload and temperature protection for the motor and function outputs reset function for all CV values CV reading CV writing bitwise CV writing indirect CVs (via register programming for older digital systems) direct register programming (CV 1 – CV4) POM – Program on Main (programming on the main track)
On order, lead time to be confirmed
Particularly small 1.2 amp locomotive decoder with 6 function outputs, suitable for small locomotives with 1 motor. The eMOTION M locomotive decoder is an NMRA/DCC-compatible locomotive decoder which, with its particularly small dimensions, is suitable for retrofitting and direct connection to a gearbox (4 pins) in very small locomotives: e.g. small garden railway locomotives, but also locomotives of smaller gauges, e.g. H0. Its total load rating is max. 1.8 amps. The decoder has 5 function outputs. With an additional voltage buffer it can do its job even more reliably in analogue and digital operation, and thereby avoids dropouts caused by dirty spots on the track. The features of the eMOTION M locomotive decoder at a glance: locomotive decoder for digital and analogue operation 14, 28 and 128 speed steps motor output rated for 1.2A programmable speed curve starting, medium and maximum speed (as well as delay times) adjustable serial and parallel control for all light and function outputs control of parallel data updates (LGB®) digital and analogue operation with automatic detection compatible with NMRA DCC and LGB MZS (all generations) latest-generation load control (for digital and analogue operation) adjustable motor frequency (70Hz – 16 kHz) 2 light connections (front, rear) max. 0.3A each 5 function outputs (2 x 0.3A, 2 x 0.05A and 1 x 0.01A (5V)) connection for a model-making servo light and function outputs dimmable and can be activated in analogue mode programmable flashing light and short-time functions shunting speed and delay times can be switched by function key simple function mapping with direction assignment all function outputs freely addressable (F1 to F16) voltage buffer connection integrated for smooth running (accessory: 8151001 or 8151501) overload and temperature protection for the motor and function outputs reset function for all CV values CV reading CV writing bitwise CV writing indirect CVs (via register programming for older digital systems) direct register programming (CV 1 – CV4) POM – Program on Main (programming on the main track)
On order, lead time to be confirmed
1-channel point decoder, which disappears directly into the track with its latest housing design. Without terminals, with only four lead-out cables (30 cm), it can be used outdoors all year round. The overload protection prevents damage to the electronics. New are 2 contact inputs, which can be used additionally (incl. direct programming function via point switch command for simpler digital systems, e.g. MZS II).
On order, lead time to be confirmed
Dealer pack eMOTION XLS sound decoder (5/pack)
On order, lead time to be confirmed
Dealer pack eMOTION LS sound decoder (5/pack)
On order, lead time to be confirmed
Dealer pack eMOTION XLS-M1 sound decoder (5/pack)
On order, lead time to be confirmed