Decoders
LokPilot 5 DCC/MM/SX/M4, 21MTC MKL, gauge H0 ,0 The LokPilot 5 is the most important representative of the LokPilot family and is suitable for almost all questions in locomotives of gauge H0 and 0. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The M4 protocol enables automatic registration at mfx®-compatible control centers. All 32 possible function keys are offered here. The LokPilot 5 decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC and AC railways.The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. Therefore, we packed the LokPilot 5 with function outputs. Depending on the interface version, each LokPilot 5 decoder offers at least 10 amplified function outputs with 250mA output current each. In the versions with PluX22 or 21MTC interface, 4 outputs are added to control servos or logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 1.5A motor current, the LokPilot 5 decoder provides enough juice even for older motors. Operational safety On request, a PowerPack can be connected to the LokPilot 5 to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Possible under Selectrix® operation. Programming must be carried out in DCC mode. Programming with "pure" Selectrix® devices is not possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Digital Motorola® (alt und neu), bis zu 255 Adressen im Motorola®-Betrieb Selectrix® Fahrbetrieb M4-Betrieb (Automatische Anmeldung an mfx®-kompatiblen Zentralen) Analog Gleichspannung (abschaltbar). Analog Wechselspannung (abschaltbar) Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Intelligenter Programmiermodus mit Märklin® 6021® Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59610 LokPilot 5 DCC/MM/SX/M4, 8-pin NEM652, gauge H0 ,0 59612 LokPilot 5 DCC/MM/SX/M4, PLUX22 NEM658, gauge H0 ,0 59616 LokPilot 5 DCC/MM/SX/M4, 6-pin NEM651, gauge H0 ,0 59619 LokPilot 5 DCC/MM/SX/M4, 21MTC NEM660, gauge H0 ,0 59649 LokPilot 5 DCC/MM/SX/M4, 21MTC MKL, gauge H0 ,0
On order, shipped within 4-5 days
LokPilot 5 DCC, 21MTC MKL, gauge H0 ,0 The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl. The decoder accepts all DCC programming modes and thanks to RailCom® the CV values can be read on the main track with RailCom equipped DCC systems. For command stations that only program the CVs from 1-255 auxiliary CV registers exist. The LokPilot 5 DCC decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACKCommands or the Lenz® ABC system. Also braking with DCC brake modules or with DC voltageis possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle trainenables automatic commuting between two train stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The top speedcan be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5DCC packed with function outputs. Depending on the interface version, each LokPilot offers 5 DCCDecoder at least 10 amplified function outputs with 250mA output current each. In the executionswith PluX22 or 21MTC interface there are 4 outputs to control servos orLogic level outputs added. All-important lighting functions are available. The brightness of each outputcan be set separately. The decoder masters automatic pushing and pullingwhen uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 DCC has been fundamentally improved again. A variably adjustablePWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors.Operation - The typical “hum” is a thing of the past. The load control now has up to10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enablesthe automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to 1.5A of motor current. Enough juice even for older motors. Operational safety On request, a PowerPack can be fitted to the LokPilot 5 DCC to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Analog Gleichspannung (abschaltbar). Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59620 LokPilot 5 DCC, 8-pin NEM652, gauge H0 ,0 59622 LokPilot 5 DCC, PLUX22 NEM658, gauge H0 ,0 59626 LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 59629 LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 59659 LokPilot 5 DCC, 21MTC MKL, gauge H0 ,0
On order, shipped within 4-5 days
LokPilot 5 micro DCC Direct, gauge: N The LokPilot 5 micro DCC Direct is the “twin” of the LokSound 5 Nano DCC. With its dimensions of 66.0mm x 8.2mm it has been specially developed for installation in Spur N vehicles of the Atlas and Intermountain brands: it can be inserted directly instead of the analog board installed there as standard. However, the decoder can also be used for similar models from other manufacturers at your own discretion. Modes The LokPilot 5 micro DCC Direct is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 micro DCC Direct decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 micro DCC Direct decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Functions The LokPilot 5 micro DCC Direct has 10 directly soldered LEDs. Two of them are intended for front and rear head lighting, two more are connected to the aux3 and AUX4 outputs to switch e.g. number boards. A further 6 LEDs on the bottom are intended for ditch lights, but can also be used for other lighting purposes on request. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 micro DCC Direct has a variable PWM clock frequency from 10kHz to 50kHz, which ensures super-quiet operation, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokPilot 5 Nano DCC Direct Decoder delivers up to 0.75A motor power. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 59721 LokPilot 5 micro DCC Direct, gauge: N
On order, shipped within 4-5 days
LokPilot 5 micro DCC Direct Atlas Legacy, gauge: N The LokPilot 5 micro DCC Direct Atlas Legacy has been specially developed for installation in N gauge locomotives of the Atlas and InterMountain brands: it can be inserted directly instead of the analog board installed there as standard. However, the decoder can also be used for similar models from other manufacturers at your own discretion. The LokPilot 5 micro DCC Direct Atlas Legacy is also a “direct style" decoder developed for early (before 2016) Atlas, InterMountain (and others). The decoder was made for locos produced before sound was added during production. The LokPilot 5 micro DCC Direct Atlas Legacy is the twin to the LokSound 5 micro DCC Direct Atlas Legacy and shares the same dimensions of 66.0mm x 8.2mm. Modes The LokPilot 5 micro DCC Direct Atlas Legacy is a “pure-bred” DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoder logs in fully automatically to a suitable digital center such as the ESU CabControl and ECoS. It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokPilot 5 micro DCC Direct Atlas Legacy Decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or DC voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An AUTOMATIC ABC commuter train allows automatic commuting between two stations. The LokPilot 5 micro DCC Direct Atlas Legacy decoder can be used on analog DC layouts. The decoder switches “on-the-fly” fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 micro DCC Direct Atlas Legacy decoder has two directly soldered LEDs, one on top (front) and one on bottom (rear). Resistor protected solder pads are provided on the bottom of the decoder, one at each end, for adding a front and rear headlight LED. Two additional pads (non-resistor protected) are for further lighting. All important lighting functions are available. The brightness of each output can be set separately. Motor Control The motor control of the LokPilot 5 micro DCC Direct Atlas Legacy decoder has a variable PWM clock frequency from 10kHz to 50kHz, which ensures super-quiet operation, especially for bell anchor motors – the hitherto typical “hum” is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique “Autotune” function allows the decoder to be automatically measured against the motor. The LokPilot 5 micro DCC Direct Atlas Legacy decoder delivers up to 0.9A motor power. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 59751 LokPilot 5 micro DCC Direct Atlas Legacy, gauge: N
On order, shipped within 4-5 days
LokPilot 5 micro DCC/MM/SX, 8-pin NEM652, gauge N, TT The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm) that it can be used even in very small locomotives Nominal sizes Z, N or TT can accommodate. Nevertheless, functionality and robustness were not spared compared to the larger versions. LokPilot 5 micro decoders are offered with all common interfaces. The versions with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but they also speak for the mfx®-compatible M4 protocol. Modes The LokPilot 5 micro is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The Next18 and PluX16 variants also allow automatic registration to mfx®-compatible control centers thanks to the M4 protocol. All 32 possible function keys are offered here. The LokPilot 5 micro decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC trains. The versions with Next18 or PluX16 can also be used on analog AC systems. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. That is why we have equipped the LokPilot 5 micro with an astonishing number of function outputs. The variants with 6-pin or 8-pin wiring harness offer 4 amplified function outputs with 180mA output current each as well as two logic level outputs for servos or Susi. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. motor control The engine control of the LokPilot 5 micro has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 0.75A motor current, the LokPilot 5 micro decoder provides enough juice for the intended application scenarios. Operational safety On request, a PowerPack can be connected to the LokPilot 5 micro to bridge dirty rail sections. Protection Of course, the motor output and the function outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59810 LokPilot 5 micro DCC/MM/SX, 8-pin NEM652, gauge N, TT 59814 LokPilot 5 micro DCC/MM/SX/M4, PluX16, gauge N, TT 59816 LokPilot 5 micro DCC/MM/SX, 6-pin NEM651, gauge N, TT 59817 LokPilot 5 micro DCC/MM/SX, 6-pin Direkt, gauge N, TT 59818 LokPilot 5 micro DCC/MM/SX/M4, Next18, gauge N, TT 59837 LokPilot 5 micro DCC/MM/SX, 6-pin Direct angled, gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 micro DCC/MM/SX, 6-pin NEM651, gauge N, TT The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm) that it can be used even in very small locomotives Nominal sizes Z, N or TT can accommodate. Nevertheless, functionality and robustness were not spared compared to the larger versions. LokPilot 5 micro decoders are offered with all common interfaces. The versions with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but they also speak for the mfx®-compatible M4 protocol. Modes The LokPilot 5 micro is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The Next18 and PluX16 variants also allow automatic registration to mfx®-compatible control centers thanks to the M4 protocol. All 32 possible function keys are offered here. The LokPilot 5 micro decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC trains. The versions with Next18 or PluX16 can also be used on analog AC systems. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. That is why we have equipped the LokPilot 5 micro with an astonishing number of function outputs. The variants with 6-pin or 8-pin wiring harness offer 4 amplified function outputs with 180mA output current each as well as two logic level outputs for servos or Susi. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. motor control The engine control of the LokPilot 5 micro has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 0.75A motor current, the LokPilot 5 micro decoder provides enough juice for the intended application scenarios. Operational safety On request, a PowerPack can be connected to the LokPilot 5 micro to bridge dirty rail sections. Protection Of course, the motor output and the function outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59810 LokPilot 5 micro DCC/MM/SX, 8-pin NEM652, gauge N, TT 59814 LokPilot 5 micro DCC/MM/SX/M4, PluX16, gauge N, TT 59816 LokPilot 5 micro DCC/MM/SX, 6-pin NEM651, gauge N, TT 59817 LokPilot 5 micro DCC/MM/SX, 6-pin Direkt, gauge N, TT 59818 LokPilot 5 micro DCC/MM/SX/M4, Next18, gauge N, TT 59837 LokPilot 5 micro DCC/MM/SX, 6-pin Direct angled, gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 micro DCC/MM/SX/M4, Next18, gauge N, TT The LokPilot 5 micro is the smallest digital decoder from ESU to date. Thanks to the use of subminiature components, 8-layer printed circuit boards and the latest manufacturing technology, it is so small with only 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm) that it can be used even in very small locomotives Nominal sizes Z, N or TT can accommodate. Nevertheless, functionality and robustness were not spared compared to the larger versions. LokPilot 5 micro decoders are offered with all common interfaces. The versions with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but they also speak for the mfx®-compatible M4 protocol. Modes The LokPilot 5 micro is a real multi-protocol decoder. He masters the data format DCC as well as Motorola®, Selectrix® and M4. In DCC format, 14 to 128 speed steps are as natural as 2 and 4-digit addresses and up to 32 functions. Thanks to RailComPlus®, the decoders log on to a suitable digital center fully automatically. It masters all DCC programming modes and, thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. Auxiliary registers exist for control centers that can only program CVs from 1-255. Motorola® users benefit from up to 28 speed steps with 255 addresses. Three additional Motorola® addresses enable the activation of 16 functions. A built-in programming mode also makes reprogramming possible with the venerable Control Unit 6021. The Next18 and PluX16 variants also allow automatic registration to mfx®-compatible control centers thanks to the M4 protocol. All 32 possible function keys are offered here. The LokPilot 5 micro decoder recognizes the Märklin® braking distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 decoder can be used on analog DC trains. The versions with Next18 or PluX16 can also be used on analog AC systems. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Usually nothing needs to be set. Features We know that you want your locomotives to be as realistic as possible. That is why we have equipped the LokPilot 5 micro with an astonishing number of function outputs. The variants with 6-pin or 8-pin wiring harness offer 4 amplified function outputs with 180mA output current each as well as two logic level outputs for servos or Susi. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs. All important lighting functions are available. The brightness of each output can be set separately. The decoder masters the automatic pressing and detaching when uncoupling for ROCO®, Krois® and Telex® couplings. motor control The engine control of the LokPilot 5 micro has been fundamentally improved again. A variably adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors - the typical "hum" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function enables the decoder to be automatically calibrated to the motor. With up to 0.75A motor current, the LokPilot 5 micro decoder provides enough juice for the intended application scenarios. Operational safety On request, a PowerPack can be connected to the LokPilot 5 micro to bridge dirty rail sections. Protection Of course, the motor output and the function outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59810 LokPilot 5 micro DCC/MM/SX, 8-pin NEM652, gauge N, TT 59814 LokPilot 5 micro DCC/MM/SX/M4, PluX16, gauge N, TT 59816 LokPilot 5 micro DCC/MM/SX, 6-pin NEM651, gauge N, TT 59817 LokPilot 5 micro DCC/MM/SX, 6-pin Direkt, gauge N, TT 59818 LokPilot 5 micro DCC/MM/SX/M4, Next18, gauge N, TT 59837 LokPilot 5 micro DCC/MM/SX, 6-pin Direct angled, gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 micro DCC, 8-pin NEM652, gauge N, TT The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a pure DCC Decoder. This lack of flexibility is rewarded with a lower price. LokPilot 5 micro DCC decoders are available with all common interfaces. The variants with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but have 2 additional function outputs. Modes The LokPilot 5 micro DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 micro DCC decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5 micro DCC equipped with an amazing number of function outputs. The variants with 6-pin or 8-pin Wiring harnesses offer 4 amplified function outputs, each with 180mA output current and two logic level outputs. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs available. All important lighting effects are available. The brightness of each output can be adjusted separately. The decoder masters automatic pushing and pulling when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The motor control of the LokPilot 5 micro DCC has been fundamentally improved again. A variable adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors- The typical “hum” is a thing of the past. The load control now has up to 10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enables the automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors. Safety A PowerPack to bypass dirty track can be fitted to the LokPilot 5 micro. Protection Of course, the motor output and the function outputs are against overload protected. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59820 LokPilot 5 micro DCC, 8-pin NEM652, gauge N, TT 59824 LokPilot 5 micro DCC, PluX16, gauge N, TT 59826 LokPilot 5 micro DCC, 6-pin NEM651, gauge N, TT 59827 LokPilot 5 micro DCC, 6-pin Direkt, gauge N, TT 59828 LokPilot 5 micro DCC, Next18, gauge N, TT 59857 LokPilot 5 micro DCC, 6-pin Direkt gewinkelt, gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 micro DCC, 6-pin NEM651, gauge N, TT The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a pure DCC Decoder. This lack of flexibility is rewarded with a lower price. LokPilot 5 micro DCC decoders are available with all common interfaces. The variants with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but have 2 additional function outputs. Modes The LokPilot 5 micro DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 micro DCC decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5 micro DCC equipped with an amazing number of function outputs. The variants with 6-pin or 8-pin Wiring harnesses offer 4 amplified function outputs, each with 180mA output current and two logic level outputs. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs available. All important lighting effects are available. The brightness of each output can be adjusted separately. The decoder masters automatic pushing and pulling when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The motor control of the LokPilot 5 micro DCC has been fundamentally improved again. A variable adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors- The typical “hum” is a thing of the past. The load control now has up to 10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enables the automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors. Safety A PowerPack to bypass dirty track can be fitted to the LokPilot 5 micro. Protection Of course, the motor output and the function outputs are against overload protected. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59820 LokPilot 5 micro DCC, 8-pin NEM652, gauge N, TT 59824 LokPilot 5 micro DCC, PluX16, gauge N, TT 59826 LokPilot 5 micro DCC, 6-pin NEM651, gauge N, TT 59827 LokPilot 5 micro DCC, 6-pin Direkt, gauge N, TT 59828 LokPilot 5 micro DCC, Next18, gauge N, TT 59857 LokPilot 5 micro DCC, 6-pin Direkt gewinkelt, gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 micro DCC, 6-pin Direkt, gauge N, TT The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a pure DCC Decoder. This lack of flexibility is rewarded with a lower price. LokPilot 5 micro DCC decoders are available with all common interfaces. The variants with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but have 2 additional function outputs. Modes The LokPilot 5 micro DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 micro DCC decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5 micro DCC equipped with an amazing number of function outputs. The variants with 6-pin or 8-pin Wiring harnesses offer 4 amplified function outputs, each with 180mA output current and two logic level outputs. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs available. All important lighting effects are available. The brightness of each output can be adjusted separately. The decoder masters automatic pushing and pulling when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The motor control of the LokPilot 5 micro DCC has been fundamentally improved again. A variable adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors- The typical “hum” is a thing of the past. The load control now has up to 10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enables the automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors. Safety A PowerPack to bypass dirty track can be fitted to the LokPilot 5 micro. Protection Of course, the motor output and the function outputs are against overload protected. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59820 LokPilot 5 micro DCC, 8-pin NEM652, gauge N, TT 59824 LokPilot 5 micro DCC, PluX16, gauge N, TT 59826 LokPilot 5 micro DCC, 6-pin NEM651, gauge N, TT 59827 LokPilot 5 micro DCC, 6-pin Direkt, gauge N, TT 59828 LokPilot 5 micro DCC, Next18, gauge N, TT 59857 LokPilot 5 micro DCC, 6-pin Direkt gewinkelt, gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 micro DCC, 6-pin Direkt gewinkelt, gauge N, TT The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a pure DCC Decoder. This lack of flexibility is rewarded with a lower price. LokPilot 5 micro DCC decoders are available with all common interfaces. The variants with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but have 2 additional function outputs. Modes The LokPilot 5 micro DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 micro DCC decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5 micro DCC equipped with an amazing number of function outputs. The variants with 6-pin or 8-pin Wiring harnesses offer 4 amplified function outputs, each with 180mA output current and two logic level outputs. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs available. All important lighting effects are available. The brightness of each output can be adjusted separately. The decoder masters automatic pushing and pulling when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The motor control of the LokPilot 5 micro DCC has been fundamentally improved again. A variable adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors- The typical “hum” is a thing of the past. The load control now has up to 10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enables the automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors. Safety A PowerPack to bypass dirty track can be fitted to the LokPilot 5 micro. Protection Of course, the motor output and the function outputs are against overload protected. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59820 LokPilot 5 micro DCC, 8-pin NEM652, gauge N, TT 59824 LokPilot 5 micro DCC, PluX16, gauge N, TT 59826 LokPilot 5 micro DCC, 6-pin NEM651, gauge N, TT 59827 LokPilot 5 micro DCC, 6-pin Direkt, gauge N, TT 59828 LokPilot 5 micro DCC, Next18, gauge N, TT 59857 LokPilot 5 micro DCC, 6-pin Direkt gewinkelt, gauge N, TT
On order, shipped within 4-5 days
LokPilot 5 Nano DCC, E24 interface, gauge: N, TT The LokPilot 5 Nano DCC is the “twin” of the LokSound 5 Nano DCC. At 19.6 mm x 8.5 mm and a thickness of only 3.2 mm, it is exactly the same size as the corresponding LokSound decoder, but does without the sound functions. The LokPilot 5 Nano DCC is equipped with the E24 interface, which will fit into many newly released N gauge locomotives. Modes The LokPilot 5 Nano DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 Nano DCC decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 Nano DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Functions Despite its small size, the LokPilot 5 Nano DCC has 8 powered function outputs as well as a 5 logic level outputs provided at the E24 interface. All important lighting functions are available. The brightness of each output can be set separately. The decoder controls the automatic start-up and disconnection when uncoupling for ROCO®, Krois® and Märklin telex ® couplings. Motor The motor control of the LokPilot 5 Nano DCC has a variable PWM clock frequency from 10kHz to 50kHz, which ensures super-quiet operation, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokPilot 5 Nano DCC decoder delivers up to 0.75A motor power. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 59925 LokPilot 5 Nano DCC, E24 interface, gauge: N, TT
On order, shipped within 4-5 days
LokPilot 5 micro DCC Direct Kato USA Widebody, gauge: N The LokPilot 5 micro DCC Direct Kato USA Widebody is the “twin” of the LokSound 5 micro DCC Direct Kato USA Widebody. With its dimensions of 47.5mm x 14.0mm x 4.5mm it has been specially developed for installation in wide body N gauge locomotives of the Kato USA brand: Most diesel locomotives of this manufacturer come with only a common DC lighting board. Finally, these models can also be easily retrofitted with a LokPilot 5 Decoder. Modes The LokPilot 5 micro DCC Direct Kato USA Widebody is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 micro DCC Direct Kato USA Widebody decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 micro DCC Direct Kato USA Widebody decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Functions Despite its compact dimensions, the LokPilot 5 micro DCC Direct Kato USA Widebody is equipped with an enormous number of function outputs. Two DIP LEDs (included in the box) can be adjusted in length and soldered in directly and controlled separately. In addition, eight (!) more powered function outputs are available. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 micro DCC Direct Kato USA Widebody has a variable PWM pulse frequency from 10kHz to 50kHz, which ensures super-quiet operation, especially for coreless motors – the typical "hum" is a thing of the past. Load control can be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokPilot 5 micro DCC Direct Kato USA Widebody Decoder delivers up to 0.75A motor power. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 59941 LokPilot 5 micro DCC Direct Kato USA Widebody, gauge: N
On order, shipped within 4-5 days
Suitable for Gauge H0e, TT and N. The decoder is equipped with the RailCom function. Maximum motor current: 0.7 A. For further technical data see data sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. Answers to possible questions can be found in this Zimo manual
On order, shipped within 10-15 days
Suitable for Gauge H0e, TT and N. The decoder is equipped with the RailCom function. Maximum motor current: 0.8 A. Length of pigtail: 35 mm. For further technical specification, see the spec sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. Answers to possible questions can be found in this Zimo manual
On order, shipped within 10-15 days
Suitable for Gauge TT and N. The decoder is equipped with the RailCom function. Maximum motor current: 0.8 A. For further technical data see data sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. This sound decoder is equipped with a pre-installed Zimo sound (sound collection). You will find an extensive list of questions/answers that are frequently posed to us in Chapter 5 of this Zimo manual .
On order, shipped within 10-15 days
Decoder with wires and 8-pole plug. Suitable for Gauge H0e, TT and N. The decoder is equipped with the RailCom function. Maximum motor current: 0.8 A. For further technical data see data sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. Answers to possible questions can be found in this Zimo manual
On order, shipped within 10-15 days
Suitable for Gauge H0e, TT and N. The decoder is equipped with the RailCom function. Maximum motor current: 0.7 A. For further technical data see data sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. This sound decoder is equipped with a pre-installed Zimo sound (sound collection). You will find an extensive list of questions/answers that are frequently posed to us in Chapter 5 of this Zimo manual .
On order, shipped within 10-15 days
HM7000-21TXS: Bluetooth® & DCC Sound Decoder (21-pin) Part of the innovative new HM7000 range, this 21-pin Bluetooth® and DCC sound decoder is ready to plug into locomotives featuring a 21-pin (NEM660) socket. You'll find the 8 pin socket in Hornby locos and many other locomotives in OO, HO and some smaller scale locomotives. The decoder is designed to supply 1000mA continuous load to the main motor and a peak demand of 1500mA, making it highly suitable for most 00 and HO scale locos. This decoder also has sound capabilities and comes with a high quality 'sugar-cube' miniature speaker. This is quickly and easily plugged into a socket on the decoder. Also included are assorted 'speaker enclosures'. When installing the speaker inside your locomotive, picking the largest enclosure which will fit inside the loco body will give the best sound reproduction from your speaker. Download your first set of sounds and install them via the HM7000 app - you can download different sound packs and change those on your decoder later if you wish. ** An R7377 Power Bank can be purchased separately and added to this decoder. We recommend for ease you do this during the first install. The Power Bank will keep the loco operating during short power outages when running over dirty track or complex points - keeping the sounds operating and the loco moving. ** Box Contents: 1 Decoder, 1 Sugar-cube Speaker, 1 set of assorted speaker enclosures. Not included: Controller - download the HM7000 free app from your App Store. R7377 Power Bank (Available separately) Locomotive
On order, lead time to be confirmed
HM7000-8: Bluetooth® & DCC Decoder (8-pin) Part of the innovative new HM7000 range, this 8-pin Bluetooth® and DCC decoder is perfect for getting OO scale locomotives working on the HM7000 system. The 8 pin socket has historicaly been fitted to Hornby locomotives manufactured prior to 2022. The decoder is designed to supply 1000mA continuous load to the main motor and a peak demand of 1500mA. ** An R7377 Power Bank can be purchased separately and added to this decoder. We recommend for ease you do this during the first install. The Power Bank will keep the loco operating during short power outages when running over dirty track or complex points.
On order, shipped within 4-5 days
HM7000-8TXS: Bluetooth® & DCC Sound Decoder (8-pin) Part of the innovative new HM7000 range, this 8-pin Bluetooth® and DCC sound decoder is ready to plug into locomotives featuring a 8-pin (NEM652) socket. You'll find the 8 pin socket in Hornby locos and many other locomotives in OO, HO and some smaller scale locomotives. The decoder is designed to supply 1000mA continuous load to the main motor and a peak demand of 1500mA. Making it highly suitable for most OO and HO scale locos. This decoder also has sound capabilities and comes with a high quality 'sugar-cube' miniature speaker. This is quickly and easily plugged into a socket on the decoder. Also included are assorted 'speaker enclosures'. When installing the speaker inside your locomotive, picking the largest enclosure which will fit inside the loco body will give the best sound reproduction from your speaker. Download your first set of sounds and install them via the HM7000 app - you can download different sound packs and change those on your decoder later if you wish. ** An R7377 Power Bank can be purchased separately and added to this decoder. We recommend for ease you do this during the first install. The Power Bank will keep the loco operating during short power outages when running over dirty track or complex points - keeping the sounds operating and the loco moving. ** Box Contents: 1 Decoder, 1 Sugar-cube Speaker, 1 set of assorted speaker enclosures. Not included: Controller - download the HM7000 free app from your App Store. R7377 Power Bank (Available separately) Locomotive
On order, lead time to be confirmed
Standard+ V2 locomotive decoder, continuous current rating 1000 mA, with NEM 652 interface, 4 function outputs, ABC, RailCom, dimensions: 25 x 15 x 3.8 mm
On order, lead time to be confirmed
The "SILVERmini+" digital decoder has a continuous current rating of 500 mA, includes a cable, 2 function outputs, ABC, RailCom, and a S.U.S.I. interface. Dimensions: 10.6 x 7.5 x 2.6 mm.
On order, lead time to be confirmed
Locomotive decoder "SILVER+ PluX12" Continuous current rating 750 mA, with interface according to NEM 658, 4 function outputs, ABC, RailCom, dimensions: 11.0 x 20.0 x 4.0 mm
On order, lead time to be confirmed