Electronic Accessories
Interiour lighting set with decoder, Entry+Red marker light, 264mm, divisible, PowerPack Option, 13 LED, yellow With the digital LED interior lights from ESU, you can retrofit your N, TT or H0 gauge passenger cars with prototypical, uniform lighting. Two versions are available to suit the desired location. The digital interior lights are 264mm long, 9mm slim and each fitted with 13 (!) LEDs. In addition to a version with warm white LEDs (50718), there is also a board with yellow LEDs (50719) so that the light color always matches your existing wagons. Features The digital interior lighting consists of a 74 mm long base section, on which a digital decoder and four LEDs are mounted, and eight adjoining sections, each equipped with one LED spaced 24mm apart. The additional sections can be cut off to customize the length to suit the wagon. Furthermore, two additional 4.5mm wide, detachable LED sections are provided on the far left and right sides to illuminate the entry area. The brightness of the LEDs can be set either using a potentiometer or via software CV and remains constant regardless of the track voltage thanks to the built-in constant voltage supply. A built-in buffer capacitor bridges small current interruptions ex works. To completely prevent flickering even with poor power pickup, a special, very compact PowerPack supercapacitor (ESU item no. 50710) can be connected directly upon request. This can power the LEDs for a few seconds. The digital interior lighting comes with a soldered red tail light. Operating modes The decoder, based on the LokPilot 5 Basic and adapted to the intended use, supports the DCC and Märklin® Motorola® protocols. It can handle 2- and 4-digit addresses and can trigger functions up to F31. Thanks to RailComPlus®, the decoders register fully automatically with a suitable DCC command station. It supports all DCC programming modes, and thanks to RailCom®, the CV values can be read on the main track with suitable command stations. Auxiliary registers are available for command stations that can only program CVs 1-255. Alternatively, the decoder can be read on the programming track without an additional load resistor. The digital interior lighting can also be used on analog AC and DC systems. In both operating modes, the direction of travel is correctly detected and the tail light is switched accordingly. Functions The 13 built-in LEDs can be individually controlled in a total of seven groups: The two entrance LEDs can each be switched separately. The tail light can also be switched separately depending on the direction of travel. Furthermore, there is an amplified output and two outputs for connecting additional LEDs (e.g., for headlights on Pilot cars or toilet lighting), which can be wired individually. Various prototypical lighting effects such as soft dimming, neon tube effects, defective neon tubes, battery lighting, and much more ensure a realistic result. The ESU V5 Function Mapping allows the individual assignment of all LED groups to the desired function keys. Robust You can rely on the experience and quality of a renowned brand manufacturer, even when it comes to digital interior lighting.
On order, shipped within 4-5 days
Linear Servo, movement 4.5 mm, with microcontroller, 30cm wire,with fittings accessories This linear servo with dimensions 26mm x 22.5mm x 10.8mm is primarily intended for installation in electric locomotives in order to subsequently make the pantographs raised and lowered. The mechanics enable very quiet, smooth running and avoid the noise produced by commercially available servos. The servos radius of movement is approx. 4.5 mm. As is usual with ESU servos, the electronics have been optimized for use in model railway systems: the “start-up twitching” has been eliminated, as has the “humming” under load. The servo can be controlled either with LokSound 5 or LokPilot 5 decoders (both decoders generate the required control impulse) or alternatively used at your own discretion on a model railway system to switch switches or gates. In this case we recommend the SwitchPilot Servo for control.
On order, shipped within 4-5 days
Cable USB-A 2.0 FTDI to RS232; 1.80m, for LokProgrammer As contemporary computers do not have a serial interface anymore we include a USB adapter cable. Since Windows Vista and Windows 7, cables that support USB 2.0 and are provided with a FTDI chip are required. The previous cables, available until the end of 2009, will not work with these operating systems due to their modified inner structures by Windows. If your LokProgrammer has been in use for a considerable time and you intend to switch to Windows 7 , you will need a new USB cable . The USB cable can be ordered at your ESU retailers shop, art. no. 51952. Art.No. 51952 Cable USB-A 2.0 FTDI to RS232; 1.80m, for LokProgrammer
On order, shipped within 4-5 days
Blindplug for adapter board for LokSound L with pin connectors, Universal On request, this dummy plug replaces a LokSound 5 L or LokSound L V4.0 decoder in locomotives that are to run on analog systems. The dummy plug is plugged onto the Adat board 51959. DIP switches can be used to configure which function outputs should be switched on or off. The definition of the direction of travel is possible. The dummy plug is useful for converters who want to prepare their track 0 or track 1 locos digitally using the 51959 board, but do not want to install a LokSound 5 L decoder straight away. Art.No. Delivery 51956 Blindplug for adapter board for LokSound L with pin connectors, Universal
On order, shipped within 4-5 days
adapter board for LokSound/LokPilot L with pin connectors This adapter board provides the suitable connections for your new LokSound/LokPilot L decoder. The decoder can be plugged directly into the socket terminal strip. All functions of the locomotive can be wired to soldering pads on the adapter board. Thus wiring is a breeze and, if necessary, the decoder can easily be exchanged. The adapter board is fixed with screws to the model. Dimensions 61.8 x 25.4 x 10.15 mm (LxWxH). 51959 with decoder
On order, shipped within 4-5 days
For the retrofit of old Märklin all-current motors you need a permanent magnet. It replaces the present field winding, and in combination with a LokSound – or LokPilot decoder, helps to make your loco run astonishingly smooth. We offer 4 different magnets, depending on the particular armature. You find the armature code number on a spare-parts sheet, which you can download from
On order, shipped within 4-5 days
For the retrofit of old Märklin all-current motors you need a permanent magnet. It replaces the present field winding, and in combination with a LokSound – or LokPilot decoder, helps to make your loco run astonishingly smooth. We offer 4 different magnets, depending on the particular armature. You find the armature code number on a spare-parts sheet, which you can download from
On order, shipped within 4-5 days
For the retrofit of old Märklin all-current motors you need a permanent magnet. It replaces the present field winding, and in combination with a LokSound – or LokPilot decoder, helps to make your loco run astonishingly smooth. We offer 4 different magnets, depending on the particular armature. You find the armature code number on a spare-parts sheet, which you can download from
On order, shipped within 4-5 days
For the retrofit of old Märklin all-current motors you need a permanent magnet. It replaces the present field winding, and in combination with a LokSound – or LokPilot decoder, helps to make your loco run astonishingly smooth. We offer 4 different magnets, depending on the particular armature. You find the armature code number on a spare-parts sheet, which you can download from
On order, shipped within 4-5 days
I/O expansion board for LokSound, LokPilot 21MTC (4x AUX, 2x Servo, Smokeunit) With this expansion board you can easily expand your LokPilot or LokSound decoder (with 21MTC interface!): All you need to do is to plug the decoder onto the expansion board and benefit from using 4 additional function outputs (AUX5 through AUX8) for lighting effects, coupler etc. In addition, you are able to connect 2 RC-servos! The 5V voltage needed (for this) will be also provided. The highlight of the expansion board is surly the control electronics for synchronised smoke units. You just need to install an ESU smoke unit (from Class 215) into your locomotive that allows to generate synchronised steam chuffs or Diesel smoke. With the help of the LokPilot / LokSound decoder all functions can be controlled in a direct way and are fully integrated into function mapping. The board measures 15.5mmx 30mmx 5.5mm (0.61 x 1.18 x 0.22 inch) and has therefore the exact size of a LokSound decoder. The module can be directly plugged into a 21MTC interface of a loco (if enough height available) or freely wired via its cable connections. Suitable for 21MTC (not MKL) decoders from generation 4.
On order, shipped within 4-5 days
Adapter board 24 pin E24 socket to PluX16 This adapter board can be connected to all decoders with an E24 connection and offers a PluX16 interface on the locomotive side. This means, for example, a LokSound 5 Nano or LokPilot 5 Nano can be easily installed in older locomotives that only provide a PluX16 interface (e.g. some Fleischmann H0 locomotives or Piko N or TT locomotives) Art.No. Delivery 51992 Adapter board 24 pin E24 socket to PluX16
On order, shipped within 4-5 days
Adapter board, 18-pin Next-18 socket to PluX12, Flex, 88mm This adapter board can be docked to all decoders with a Next18 connection and offers a PluX12 interface on the locomotive side. In particular, TT locomotives from Tillig can now be easily converted with our LokSound 5 micro Next18 or LokPilot 5 micro Next18. The flex circuit board can be folded and extended to almost any length. The adapter board comes with shrink tubing and speaker connection cables. Art.No. Delivery 51997 Adapter board, 18-pin Next-18 socket to PluX12, Flex, 88mm
On order, shipped within 4-5 days
Adapter board 21MTC to Next18, for certain Liliput engines This small adapter board is a practical helper for equipping some models (e.g. from Liliput) with a LokSound decoder: A 21MTC interface was installed there, but the required length for a LokSound 5 decoder was not taken into account. With the help of this adapter board, a LokSound 5 micro can be used horizontally in the available installation space. If the width is 21mm, these locomotives can now also be easily converted to LokSound. Dimensions with LokSound 5 micro 58818 plugged in: total width 21.5mm x 19mm length. Art.No. Delivery 51998 Adapter board 21MTC to Next18, for certain Liliput engines 51998 with 58818
On order, shipped within 4-5 days
Decoder tester for decoder.NEM651,652,21MTC,PluX22,Next18, Single wires. Coreless motor, LED monitor, 20mm spk., Extension port If necessary, you can add the Decoder Tester Extension to your Profi Decoder Tester: Plugged into the side of the Decoder Tester it enables you to comfortably test all large scale decoders. If you also have to deal with large scale LokSound XL or LokSound L decoders in your workshop, the Profi Decoder Tester Extension is just the right thing for you: You can plug on LokSound XL decoders with multi-pin connectors as well as LokSound L decoders directly and easily test them. The extension module has multi-pin connectors for direct plug-on of the decoder types mentioned above. An LED monitor with 12 LEDs displays the status of all physical function outputs. You may also plug on a second speaker or sensor inputs onto the multi-pin connector for quick and easy testing. Up to four servos may also be plugged on for direct testing. Especially for the LokSound L, connecting pins for a smoke generator have also been added. The Profi Decoder Tester Extension represents the perfect test and programming bench in conjunction with the Profi Decoder Tester, where you can test and program almost all (ESU) decoders quickly and easily. Art.No. Delivery 53900 Decoder tester for decoder.NEM651,652,21MTC,PluX22,Next18, Single wires. Coreless motor, LED monitor, 20mm spk., Extension port 53901 Decoder tester extension for LokSound XL V4.0, LokSound L V4.0 with LED monitor, servo connectors
On order, shipped within 4-5 days
Adapter board for LokSound L / LokPilot L, with screw terminals This adapter board ensures the convenient connection of your LokSound 5 L or LokPilot 5 L Decoders. The decoder is inserted directly into the socket strips. On the output side, the most important connections can be contacted directly on robust screw terminals – without soldering! A socket for the optional connection of a SUSI module as well as pin headers for the direct connection of four RC servos complete the equipment.This adapter board allows professional, clean cabling of your locomotive and the decoder can be easily replaced in case of emergency.The adapter board is fastened with screws in the model. Dimensions 76.2 x 26.4 x 11 mm (LxWxH). Art.No. Delivery 53950 Adapter board for LokSound L / LokPilot L, with screw terminals
On order, shipped within 4-5 days
Adapter board for Hübner Schienenbus, 21MTC interface for LokSound or LokPilot Decoders This adapter board is for owners of a Hübner railbus in track 1 (Art. No. 4070 or 4071) thought. There, a LokSound 2 decoder was installed in the motor car on a special adapter, and in the control car a specially made light change decoder was installed. With the help of this adapter you can finally replace these old decoders with a modern LokSound 5 or LokPilot 5 Fx decoder. Insert a decoder with 21MTC snide into the adapter board and then install it in the railbus. Nothing needs to be rewired, all lamps will work correctly. Note: Not suitable for the new edition of the railbus under Märklin® direction. Art.No. Delivery 53951 Adapter board for Hübner Schienenbus, 21MTC interface for LokSound or LokPilot Decoders
On order, lead time to be confirmed
Adapter board, for BLI steam engines with Paragon 3/4 Decoder, 21MTC, with PowerPack With the help of the BLI Paragon 3/4 (P34) adapter board, H0 Scale tender steam locomotives from Broadway Limited (BLI), in which a Paragon 3 or Paragon 4 decoder was factory installed, can finally be equipped with a LokSound 5 decoder without much effort. All you have to do is open the tender, remove the standard Paragon 3 or 4 decoder and install the BLI P34 adapter board. All connections can be made exactly as before: The type and position of all plug connections is exactly like for the factory installed decoder. No soldering work needs to be done. The locomotive tender coupling can also remain. The locomotive itself does not need to be opened. The LokSound 5 decoder can communicate with the electronics built into the locomotive using a serial protocol and directly control all smoke and light functions. An integrated PowerPack ensures uninterrupted operation even on dirty rails. The BLI P34 adapter board requires a LokSound 5 decoder with 21MTC interface. From firmware 5.9.159 this can speak the required protocol instead of SUSI. Appropriate preconfigured sound files will gradually be made available on our website. Art.No. Delivery 53952 Adapter board, for BLI steam engines with Paragon 3/4 Decoder, 21MTC, with PowerPack
On order, lead time to be confirmed
Adapter board, for Kato USA N WideBody, for E24 Interface This adapter board with dimensions 47.5mm x 14.0mm fits in such Kato (USA) N-gauge locomotives that have a wide body design such as F-units. It replaces the original circuit board and has connection pads for motor and track as well as the function outputs AUX1, AUX2, AUX3, AUX4, AUX5, AUX6, AUX7 and AUX8. Either a LokSound 5 Nano or a LokPilot 5 Nano can be plugged into the E24 interface. Connection pads for an ESU PowerPack are also available of course. Art.No. Delivery 53954 Adapter board, for Kato USA N WideBody, for E24 Interface
On order, shipped within 4-5 days
Adapter board with PowerPack for E24 Interface This adapter board with the dimensions 54.0mm x 17.0mm has an ESU PowerPack ‘On Board’. Although the capacitors protruding at the front and rear make for a total length of 70mm, this adapter board is ideal for converting many American H0 locomotives from Atlas or Athearn, where it replaces the original circuit board. In addition to connection pads for motor and track, there are also pads for the function outputs AUX1, AUX2, AUX3, AUX4, AUX5, AUX6, AUX7 and AUX8. The series resistors for LEDs installed there can be bridged if required. Either a LokSound 5 Nano or a LokPilot 5 Nano can be plugged into the E24 interface. Art.No. Delivery 53955 Adapter board with PowerPack for E24 Interface
On order, shipped within 4-5 days
Adapter board, 18-pin Next-18 socket to RCN-114 MTC14, Flex Using this adapter board with the dimensions 13.5mm x 8.4mm, Minitrix® locomotives with MTC14 interface can finally be equipped with a LokSound decoder at your own discretion: The adapter board is flexible and is plugged directly into the 14MTC socket of the locomotive, on the other side you can use any decoder with Next18, preferably of course the LokSound 5 Nano Next 18. Additional solder pads for speakers and PowerPack are provided as well. Before installation, please check the available space in the locomotive and in particular whether the locomotive housing can still be closed: The ‘sandwich’ of adapter board and LokSound decoder is somewhat thicker than specified in the VHDM standard RCN-114. ESU cannot guarantee that the conversion will work in all affected locomotives. Art.No. Delivery 53956 Adapter board, 18-pin Next-18 socket to RCN-114 MTC14, Flex
On order, shipped within 4-5 days
PowerPack Maxi energy buffer for LokSound L V4.0, LokSound V4.0, LokSound 5 L and LokSound 5, LokPilot 5 and LokPilot 5 L 2x 5F/2.7V The new ESU PowerPack Maxi has been developed as the powerful complement to the LokSound L V4.0 / LokSound 5 L decoder. It can, of course, provided there is sufficient space, also be connected to all LokPilot V4.0, LokSound V4.0, LokSound V4.0 M4, LokPilot 5 or LokSound 5 decoders. It provides uninterrupted power to your locomotive when traversing dirty track and long turnout ladders. All sound, lighting and motor functions are buffered with the aid of two energy storage capacitors enabling your models – subject to the total energy consumption - to continue running for up to three seconds. The PowerPack Maxi incorporates an integral charging circuit controlled by the decoder. Therefore it may be connected even during programming. The charging current is limited in order to avoid an undue load on the booster, in case there are several models in the same booster sector. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). The space requirements of the PowerPack Maxi of about 27.5 mm x 15.7 mm x 13 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Maxi to the decoder. The wires are already soldered to the PowerPack Maxi but must be soldered to the appropriate solder pads of the decoder. Please note that due to technical reasons the PowerPack cannot operate in analogue mode: Buffering is therefore not possible in analogue mode. Art.No. Delivery 54672 PowerPack Maxi energy buffer for LokSound L V4.0, LokSound V4.0, LokSound 5 L and LokSound 5, LokPilot 5 and LokPilot 5 L 2x 5F/2.7V
On order, shipped within 4-5 days
PowerPack MiniXS, energy buffer with MCU for LokPilot 5 / LokSound 5, 6*0.3F/2.7V, 29 x 5.1 x 15mm The ESU PowerPack MiniXS can be wired to all fifth generation ESU decoders (LokSound 5, LokPilot 5, LokPilot 5 Basic). It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (6 x 0.3 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound system. Subject to the energy consumption of your model it may continue to move for up to 1.5 seconds. This extremely flat module is intended for smaller vehicles with moderate power consumption. The PowerPack MiniXS is equipped with a microcontroller and incorporates an charging circuit controlled by the decoder. Therefore it may be connected even during programming. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). The output voltage is adjusted fully automatically to the track voltage by the microcontroller in order to avoid flickering of the lighting when buffering is activated. The space requirements of the PowerPack MiniXS of about 29 mm x 5.1 mm x 15 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack MiniXS to the decoder. Art.No. Delivery 54673 PowerPack MiniXS, energy buffer with MCU for LokPilot 5 / LokSound 5, 6*0.3F/2.7V, 29 x 5.1 x 15mm
On order, shipped within 4-5 days
PowerPack Midi, energy buffer with MCU for LokPilot 5 / LokSound 5, 6*1F/2.7V, 20.8 x 13.8 x 13.4mm The ESU PowerPack Midi can be wired to all fifth generation ESU decoders (LokSound 5, LokPilot 5, LokPilot 5 Basic). It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (6x1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound system. Subject to the energy consumption of your model it may continue to move for up to three seconds. The PowerPack Midi is equipped with a microcontroller and incorporates an charging circuit controlled by the decoder. Therefore it may be connected even during programming. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). The output voltage is adjusted fully automatically to the track voltage by the microcontroller in order to avoid flickering of the lighting when buffering is activated. The space requirements of the PowerPack Midi of about 20.8 mm (L) x 13.8 mm (W) x 13.4 mm (H) must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Midi to the decoder. Art.No. Delivery 54674 PowerPack Midi, energy buffer with MCU for LokPilot 5 / LokSound 5, 6*1F/2.7V, 20.8 x 13.8 x 13.4mm
On order, shipped within 4-5 days
Smoke unit, Dual Mini (Exhaust + Cylinder) (Gauge 0) for LokSound XL device with electronic board Our smoke generator "Dual small" is suitable for vehicles of the nominal sizes gauge G, and 1 but also for smaller vehicles in gauge 0. Both exhaust steam and cylinder steam are integrated in a compact housing. This means that you can finally retrofit your older locomotives with a realistic cylinder steam. The "Dual Small" smoke generator has a common tank that can be filled from above. Two separate fan motors with separate heating and temperature elements ensure a strong steam output. The required control electronics is housed on a separate board, only 36 mm x 19 mm x 5 mm in size, and controls both the amount of smoke and the fan speed regardless of the level or rail voltage. A burn-through in the case of an empty tank is preventable. The control electronics are simply placed between the smoke generator and the locomotive sound decoder in a suitable location in the vehicle. Our LokSound 5 L and LokSound 5 XL are ideal for control, but the previous versions LokSound XL V4.0 or LokSound L V4.0 can also be used. The smoke generator Dual small is 51.5 mm long, 27.5 mm wide and 30.5 mm high and is made of temperature-resistant plastic. Thanks to various, cut-off fastening straps, it should be possible to install it in many locomotives. Art.No. Delivery 54676 Smoke unit, Dual Mini (Exhaust + Cylinder) (Gauge 0) for LokSound XL device with electronic board
On order, shipped within 4-5 days