Freight wagons
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
In stock: 1 on the shelf, shipped within 1-3 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
In stock: 1 on the shelf, shipped within 1-3 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
In stock: 1 on the shelf, shipped within 1-3 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
In stock: 1 on the shelf, shipped within 1-3 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
In stock: 1 on the shelf, shipped within 1-3 days
Prototype Tariff conditions on the one hand and technical conditions on the other resulted in all State railway administrations developing box cars with almost identical dimensions and payloads. These cars had a 4.5 m wheelbase, a length over buffers of 9.3 m for unbraked cars, a payload of 15 t, later 17 t and a floor area of approx. 21 square metres. This type of freight construction became the most important and most built box car; it originally had the type identifier Gm. The most common of these State railway cars, which numbered 47,533, were built according to the Prussian style sheet IId8. After the founding of the Deutscher Staatsbahn Wagen Verband (German state railway car federation) DWV in 1909, the federation car construction type A2 was developed from this. From 1911 a phenomenal total of 121,770 units were built, making it the most heavily produced box car. It dominated the image of the German goods trains until the early days of the third era. These cars were scattered all over Europe by two world wars, there were no European railway administrations where this type of car was not used at least temporarily. Model True to original frame construction Precise replica of board joints Metal wheels and axles Multi-part brake system Individually mounted signal holder Brake blocks in wheel plane Perforated car body supports Precise paintwork and painting Individually mounted axle box cover
In stock: 1 on the shelf, shipped within 1-3 days
Prototype In the 1970s, the works of the GDR coach building industry produced almost exclusively for export. The DR therefore had to look elsewhere to replace the ageing fleet of vehicles and have more vehicles available for the increased transport requirements. This was partly solved by producing new cars in own repair shops but this technology was not suitable for special cars. At the beginning of the 1970s, the foreign trade ministry succeeded in concluding comprehensive compensation business with France, as a result of which the DR received approx. 20,000 new freight cars of various classes. Among these, 1,250 four-axle mineral oil tank cars were delivered from 1975 onwards, which were classified under the documentation number 8105 and Class Uahs. Their number group began with 727 0000. The car had a welded undercarriage made of St 52-3 without middle longitudinal supports with bogies of type Y25Cs and a divided draw gear. The five-section tank made of 7mm steel plate (9mm in the floor area) has a volume of 85150 litres and therefore allows complete exploitation of the maximum permissible wheelset load at that time of 20t. The compressed air brake of type KE-GP with brake rod actuators and mechanical load braking was complemented by a handbrake operated from a platform and complied with the latest technical standards of that time. The cars were used above all in block trains mainly to transport fuels such as petrol and diesel. Model Fine replica of the Y-25 bogies Precise paintwork and painting NEM-standard short-coupling True to original brake unit
In stock: 1 on the shelf, shipped within 1-3 days
Prototype With the beginning of World War II and the sharp increase in transportation tasks, the DRG suffered from a striking wagon shortage. The only possible remedy was the construction of new wagon types in order to increase the load capacity and loading space volume on the one hand and to reduce the necessary steel consumption drastically on the other hand. Among others, the twoaxle Gmhs Bremen goods wagon was built as part of these efforts. In comparison with the most recent design, the Ghs Oppeln, the wheel base was enlarged by 1 metre, increasing the loading space by 5 m³. Furthermore, almost 2 tonnes of steel were saved per wagon, pushing the net weight down below 10 tonnes. From 1943 to January 1945, a total of 7,230 wagons were built in this way. 3,440 of them were equipped with a handbrake platform protruding over the buffers on one side, increasing the wagon length by only 100 mm. As a result of the war events, the wagons were spread all over Europe so that Gmhs “Bremen” wagons were found in almost all Central-European countries. The wagons were exchanged between the different railways only in part, and not at all between the countries of the later Eastern bloc and Western Europe. Model Precise paintwork and painting Finely engraved fan grill True to original brake unit on the car bottom NEM-standard short-coupling
In stock: 1 on the shelf, shipped within 1-3 days
Prototype In 1939/40, the Köln-Deutz (Cologne-Deutz) and Uerdingen wagon factories each constructed a quadruple axle tank wagons in a lightweight design. Directly related to this, Westwaggon also manufactured the prototype of the tub-style tender, with which the war locomotives belonging to the BR 42 and 52 were coupled. The development was primarily driven by the military since it was necessary to transport enormous amounts of crude oil and fuels for replenishment purposes. As was the case with all war designs, the lightweight design was fully utilised in order to maximise the potential of the available steel quota. However, it soon became apparent that this was done to the detriment of the durability. At this point, both manufacturers were developing wagons with self-supporting tanks. Whilst Deutz left it at puffer beams, the Uerdinger design also boasted solebars manufactured from bevelled profiles that were intended to contribute in absorbing longitudinal compression forces. The main data of both versions was identical: The length over buffers amounted to 12.40 m, the bogie pivot distance amounted to 6.60 m and the tank contained 63 m3. As a result of the compact design, this amount lead to axle and metre load problems, meaning that it was not possible to completely fill the tank on all routes. Pressed sheet metal bogies with a 2.00 m wheel base were used as the running gear. The wagons that were built up until 1945 were deployed at "Wifo" (scientific research community) and oil associations in order to supply the German Armed Forces. After 1945, various European companies reproduced the wagons in a more advanced form, as did Tatra in Prague in 1946. In 1955, SEAG supplied almost 500 units of the wagons developed from the Uerdingen design to the United States Transportation Corps (USTC). Due to the war, many wagons were lost or remained in the territories of other European state railways . The wagons located in the catchment area of the western occupation zones made their way to VTG, which emerged from the former "Wifo" in 1951. In addition to this, mineral oil companies deployed further wagons in the form of P wagons and emerged as main tenants of the VTG wagons. The wagons that stayed with DR remained in the inventory of the state railway and were only leased out on a long-term basis, primarily to PCK Schwedt/ Oder in this case. The last wagons were only removed from the inventory in the 1990s and were being used as maintenance cars or station wagons. In this guise, they could still be regularly seen after the turn of the millennium. Model Brake blocks in wheel plane Separately mounted buffers Precise paintwork and painting Freestanding placards Metal wheels True to original frame construction
In stock: 1 on the shelf, shipped within 1-3 days
Prototype Based on the UIC standard coach Gmhs 53, DB developed a 2-m longer waggon which otherwise complied with the UIC requirements in all its equipment features. Unlike its predecessor, it already had the newly standardised 2-m-wide loading door. At the time, UIC was not able to agree on a larger standard design, so this emerged only later in the form of the Glmms 61. Therefore, the waggon - designated Glm(e)hs 50 - was only a little longer than the pre-war large-capacity covered freight cars, which caused a great deal of controversy even at the time of construction. Even then, there were demands for a waggon with a loading length of at least 12.5 m, which meant the enlargement of the loading space did not go far enough for many customers, while others considered the waggons were too far removed from UIC requirements. Despite all these issues, some 12,000 waggons were built from 1953 - 1958 - up to 1954 with board walls, then with plate walls. Some one quarter of all waggons were fitted with a handbrake, at first with the characteristic sheet metal brakeman's cab. At least 700 waggons featured electric heating so that they could compete in express goods traffic in passenger trains. Some waggons were rented long-term and painted with advertising of the renting company. By the mid-seventies, the waggons with board walls had been decommissioned or upgraded with plate walls. Since 1965, the Glm(e)hs 50 were designated Gbrs(-v) 245, in 1980 after the heating pipes were mostly removed, they were renamed Gos(-uv) 245. Then, in the 80s, the inventory started to be reduced, although larger inventories were sold to DR In 1997, 35 waggons were still in the inventory, and the last three were taken out of service in 2000. Model NEM-standard short-coupling Bogie with three-point support True to original brake unit on the car bottom Metal wheels Precise paintwork and painting True to original frame construction
In stock: 1 on the shelf, shipped within 1-3 days
Prototype The Swiss began standardising some types of goods wagons at an early stage. They were then also procured by all private railways in order to improve repairs and spare part stock-keeping. They included closed goods wagons with a 4.5 m wheel base and a frame length of 7.10 m. Later, the wheel base was increased to 5 m in order to improve the running characteristics. In this form, high numbers of the wagons that were given the K2 designation were procured by SBB. Model Precise replica of board joints Finely engraved fan grill Precise paintwork and painting NEM-standard short-coupling Metal wheels True to original frame construction
In stock: 1 on the shelf, shipped within 1-3 days
Prototype The Swiss began standardising some types of goods wagons at an early stage. They were then also procured by all private railways in order to improve repairs and spare part stock-keeping. They included closed goods wagons with a 4.5 m wheel base and a frame length of 7.10 m. Later, the wheel base was increased to 5 m in order to improve the running characteristics. In this form, high numbers of the wagons that were given the K2 designation were procured by SBB. Model Precise replica of board joints Finely engraved fan grill Precise paintwork and painting NEM-standard short-coupling Metal wheels True to original frame construction
In stock: 1 on the shelf, shipped within 1-3 days
Prototype After the war, there was a major lack of luggage wagons for highspeed long-distance trains. However, the young DB decided to use the available money to construct new passenger carriages and to solve the luggage wagon problem through conversions. In order to do so, it used approximately 600 substitute passenger carriages that remained in its inventory. Passengers could not be expected to travel in these wagons due to their interior fittings and their mediocre running properties. Two of these car bodies were connected, equipped with a strut bracing and placed on two American-design bogies. The approximately 290 luggage wagons that were produced in this manner from 1950 onwards were given the MPw4ie-54/55 and MPw4yg-57 designations. Although the first wagons were only equipped with the open entrance platforms from their donor carriages, they were quickly replaced with a “transfer tunnel” in order to offer a transfer to the next wagon whilst also being protected against the elements. This transfer was also then equipped with a rubber bulge in order to connect to modern wagons. DB arranged for numerous medical and auxiliary equipment cars to be built using the same construction principles. To begin with, the wagons were first used in the premium high-speed train service. However, they were then moved to express goods and district services upon the emergence of new wagons. Some wagons were given additional equipment for the transport of freshly-hatched chicks and travelled in express trains between Italy and Germany. Numerous wagons that were given the designations MDyg-986 and -996 from 1966 onwards were further modernised and equipped with panel walls and new rubber-mounted windows. These wagons also remained in use in this design after 1989 and were also used in the DR (German Railway) area for the transport of express goods. The use of these wagons was halted suddenly in 1992 following a tragic train accident. A buffer fell from a track maintenance wagon causing 14 goods wagons to derail with which an approaching express train collided. The cause was material fatigue on the console upon which the buffers were fastened in order to create space for the access platform. Consequently, all wagons equipped with such consoles were removed from service and only those that had to be used were refurbished. This affected the auxiliary equipment cars built on the same principle but did not affect the MDyg. Model Finely engraved bogies True to original brake unit Individually mounted battery box Replicated internal mesh of windows Free standing handle bars True to original frame construction Tip bearing wheelsets Interior fittings in multicolour painting Interior fittings in multicolour painting
On order, shipped within 10-15 days
Prototype After the war, there was a major lack of luggage wagons for highspeed long-distance trains. However, the young DB decided to use the available money to construct new passenger carriages and to solve the luggage wagon problem through conversions. In order to do so, it used approximately 600 substitute passenger carriages that remained in its inventory. Passengers could not be expected to travel in these wagons due to their interior fittings and their mediocre running properties. Two of these car bodies were connected, equipped with a strut bracing and placed on two American-design bogies. The approximately 290 luggage wagons that were produced in this manner from 1950 onwards were given the MPw4ie-54/55 and MPw4yg-57 designations. Although the first wagons were only equipped with the open entrance platforms from their donor carriages, they were quickly replaced with a “transfer tunnel” in order to offer a transfer to the next wagon whilst also being protected against the elements. This transfer was also then equipped with a rubber bulge in order to connect to modern wagons. DB arranged for numerous medical and auxiliary equipment cars to be built using the same construction principles. To begin with, the wagons were first used in the premium high-speed train service. However, they were then moved to express goods and district services upon the emergence of new wagons. Some wagons were given additional equipment for the transport of freshly-hatched chicks and travelled in express trains between Italy and Germany. Numerous wagons that were given the designations MDyg-986 and -996 from 1966 onwards were further modernised and equipped with panel walls and new rubber-mounted windows. These wagons also remained in use in this design after 1989 and were also used in the DR (German Railway) area for the transport of express goods. The use of these wagons was halted suddenly in 1992 following a tragic train accident. A buffer fell from a track maintenance wagon causing 14 goods wagons to derail with which an approaching express train collided. The cause was material fatigue on the console upon which the buffers were fastened in order to create space for the access platform. Consequently, all wagons equipped with such consoles were removed from service and only those that had to be used were refurbished. This affected the auxiliary equipment cars built on the same principle but did not affect the MDyg. Model Finely engraved bogies True to original brake unit Individually mounted battery box Replicated internal mesh of windows Free standing handle bars True to original frame construction Tip bearing wheelsets Interior fittings in multicolour painting Interior fittings in multicolour painting
On order, shipped within 10-15 days
Prototype After the war, there was a major lack of luggage wagons for highspeed long-distance trains. However, the young DB decided to use the available money to construct new passenger carriages and to solve the luggage wagon problem through conversions. In order to do so, it used approximately 600 substitute passenger carriages that remained in its inventory. Passengers could not be expected to travel in these wagons due to their interior fittings and their mediocre running properties. Two of these car bodies were connected, equipped with a strut bracing and placed on two American-design bogies. The approximately 290 luggage wagons that were produced in this manner from 1950 onwards were given the MPw4ie-54/55 and MPw4yg-57 designations. Although the first wagons were only equipped with the open entrance platforms from their donor carriages, they were quickly replaced with a “transfer tunnel” in order to offer a transfer to the next wagon whilst also being protected against the elements. This transfer was also then equipped with a rubber bulge in order to connect to modern wagons. DB arranged for numerous medical and auxiliary equipment cars to be built using the same construction principles. To begin with, the wagons were first used in the premium high-speed train service. However, they were then moved to express goods and district services upon the emergence of new wagons. Some wagons were given additional equipment for the transport of freshly-hatched chicks and travelled in express trains between Italy and Germany. Numerous wagons that were given the designations MDyg-986 and -996 from 1966 onwards were further modernised and equipped with panel walls and new rubber-mounted windows. These wagons also remained in use in this design after 1989 and were also used in the DR (German Railway) area for the transport of express goods. The use of these wagons was halted suddenly in 1992 following a tragic train accident. A buffer fell from a track maintenance wagon causing 14 goods wagons to derail with which an approaching express train collided. The cause was material fatigue on the console upon which the buffers were fastened in order to create space for the access platform. Consequently, all wagons equipped with such consoles were removed from service and only those that had to be used were refurbished. This affected the auxiliary equipment cars built on the same principle but did not affect the MDyg. Model Finely engraved bogies True to original brake unit Individually mounted battery box Replicated internal mesh of windows Free standing handle bars True to original frame construction Tip bearing wheelsets Interior fittings in multicolour painting Interior fittings in multicolour painting
On order, shipped within 10-15 days
Prototype After the war, there was a major lack of luggage wagons for highspeed long-distance trains. However, the young DB decided to use the available money to construct new passenger carriages and to solve the luggage wagon problem through conversions. In order to do so, it used approximately 600 substitute passenger carriages that remained in its inventory. Passengers could not be expected to travel in these wagons due to their interior fittings and their mediocre running properties. Two of these car bodies were connected, equipped with a strut bracing and placed on two American-design bogies. The approximately 290 luggage wagons that were produced in this manner from 1950 onwards were given the MPw4ie-54/55 and MPw4yg-57 designations. Although the first wagons were only equipped with the open entrance platforms from their donor carriages, they were quickly replaced with a “transfer tunnel” in order to offer a transfer to the next wagon whilst also being protected against the elements. This transfer was also then equipped with a rubber bulge in order to connect to modern wagons. DB arranged for numerous medical and auxiliary equipment cars to be built using the same construction principles. To begin with, the wagons were first used in the premium high-speed train service. However, they were then moved to express goods and district services upon the emergence of new wagons. Some wagons were given additional equipment for the transport of freshly-hatched chicks and travelled in express trains between Italy and Germany. Numerous wagons that were given the designations MDyg-986 and -996 from 1966 onwards were further modernised and equipped with panel walls and new rubber-mounted windows. These wagons also remained in use in this design after 1989 and were also used in the DR (German Railway) area for the transport of express goods. The use of these wagons was halted suddenly in 1992 following a tragic train accident. A buffer fell from a track maintenance wagon causing 14 goods wagons to derail with which an approaching express train collided. The cause was material fatigue on the console upon which the buffers were fastened in order to create space for the access platform. Consequently, all wagons equipped with such consoles were removed from service and only those that had to be used were refurbished. This affected the auxiliary equipment cars built on the same principle but did not affect the MDyg. Model Finely engraved bogies True to original brake unit Individually mounted battery box Replicated internal mesh of windows Free standing handle bars True to original frame construction Tip bearing wheelsets Interior fittings in multicolour painting Interior fittings in multicolour painting
On order, shipped within 10-15 days
Brake blocks in wheel plane Individually mounted axle brake rod Individually mounted axle box cover Individually mounted brake systems True to original frame construction Die-cast zinc floor Insertable stakes individually enclosed
On order, shipped within 10-15 days
Prototype When the DRG [Deutsche Reichsbahn-Gesellschaft] was founded, a large quantity of rail carriages according to the Prussian standards were assumed meaning that, due to the modest financial means, there was no opportunity to procure high quantities of succession models. Although a 4-axle rail carriage was taken into consideration during the set-up of replacement construction drawings, only a limited amount of 95 units were built. Demand for a new 4-axle rail carriage only grew with the emergence of welding technology and the armament of the German Reich. Consequently, multiple prototypes and ranges with numerous differences were created in quick succession. In 1934, SEAG supplied the first two trial wagons. They were produced using St 52 and also had a removable wooden or steel brakeman’s cab respectively. The further deliveries up until 1939 were also produced using St 52, had three cross-members and seven stake pairs. The brakeman’s cab was removable. An amended variant was built from 1941 onwards. This now consisted of the weaker St 37 which meant that a fourth cross-member had to be included. Accordingly, there were now eight lateral stake pairs. For vehicle transports, the brakeman’s cab only had a foldable platform railing. At the request of the Wehrmacht, all of the older wagons had to be converted in this manner. The first deliveries boasted a welded box bogie but all later deliveries were equipped with the press plate bogies. In addition to the deliveries to the DR, the Wehrmacht also received wagons and used them for military purposes, e.g. in the trains of the mobile V2 ramps. In total, approximately 3,500 wagons were built by the end of the war. After 1945, the welded rail carriages were distributed throughout half of Europe. In France, the equipping of these carriages with new bogies is still common. At the end of the war, DB had approximately 1,400 wagons in the inventory and it is estimated that DR had about 500. Both railway companies continued to use the wagons for a long period of time and they were only withdrawn in the 1980s. Even in 1979, DB had over 1,000 of the wagons bearing the R 672 designation in use. The original wagons were withdrawn earlier in the DR. However, the lack of wagons in the 1980s lead to the last R 672 wagons being purchased from DB. DR designated them as Rkk [3811] and used them until the slump in traffic volume in 1990. Model Brake blocks in wheel plane Individually mounted axle brake rod Individually mounted axle box cover Individually mounted brake systems True to original frame construction Die-cast zinc floor Insertable stakes individually enclosed
On order, shipped within 10-15 days
Prototype When the DRG [Deutsche Reichsbahn-Gesellschaft] was founded, a large quantity of rail carriages according to the Prussian standards were assumed meaning that, due to the modest financial means, there was no opportunity to procure high quantities of succession models. Although a 4-axle rail carriage was taken into consideration during the set-up of replacement construction drawings, only a limited amount of 95 units were built. Demand for a new 4-axle rail carriage only grew with the emergence of welding technology and the armament of the German Reich. Consequently, multiple prototypes and ranges with numerous differences were created in quick succession. In 1934, SEAG supplied the first two trial wagons. They were produced using St 52 and also had a removable wooden or steel brakeman’s cab respectively. The further deliveries up until 1939 were also produced using St 52, had three cross-members and seven stake pairs. The brakeman’s cab was removable. An amended variant was built from 1941 onwards. This now consisted of the weaker St 37 which meant that a fourth cross-member had to be included. Accordingly, there were now eight lateral stake pairs. For vehicle transports, the brakeman’s cab only had a foldable platform railing. At the request of the Wehrmacht, all of the older wagons had to be converted in this manner. The first deliveries boasted a welded box bogie but all later deliveries were equipped with the press plate bogies. In addition to the deliveries to the DR, the Wehrmacht also received wagons and used them for military purposes, e.g. in the trains of the mobile V2 ramps. In total, approximately 3,500 wagons were built by the end of the war. After 1945, the welded rail carriages were distributed throughout half of Europe. In France, the equipping of these carriages with new bogies is still common. At the end of the war, DB had approximately 1,400 wagons in the inventory and it is estimated that DR had about 500. Both railway companies continued to use the wagons for a long period of time and they were only withdrawn in the 1980s. Even in 1979, DB had over 1,000 of the wagons bearing the R 672 designation in use. The original wagons were withdrawn earlier in the DR. However, the lack of wagons in the 1980s lead to the last R 672 wagons being purchased from DB. DR designated them as Rkk [3811] and used them until the slump in traffic volume in 1990. Model Brake blocks in wheel plane Individually mounted axle brake rod Individually mounted axle box cover Individually mounted brake systems True to original frame construction Die-cast zinc floor Insertable stakes individually enclosed
On order, shipped within 10-15 days
Prototype When the DRG [Deutsche Reichsbahn-Gesellschaft] was founded, a large quantity of rail carriages according to the Prussian standards were assumed meaning that, due to the modest financial means, there was no opportunity to procure high quantities of succession models. Although a 4-axle rail carriage was taken into consideration during the set-up of replacement construction drawings, only a limited amount of 95 units were built. Demand for a new 4-axle rail carriage only grew with the emergence of welding technology and the armament of the German Reich. Consequently, multiple prototypes and ranges with numerous differences were created in quick succession. In 1934, SEAG supplied the first two trial wagons. They were produced using St 52 and also had a removable wooden or steel brakeman’s cab respectively. The further deliveries up until 1939 were also produced using St 52, had three cross-members and seven stake pairs. The brakeman’s cab was removable. An amended variant was built from 1941 onwards. This now consisted of the weaker St 37 which meant that a fourth cross-member had to be included. Accordingly, there were now eight lateral stake pairs. For vehicle transports, the brakeman’s cab only had a foldable platform railing. At the request of the Wehrmacht, all of the older wagons had to be converted in this manner. The first deliveries boasted a welded box bogie but all later deliveries were equipped with the press plate bogies. In addition to the deliveries to the DR, the Wehrmacht also received wagons and used them for military purposes, e.g. in the trains of the mobile V2 ramps. In total, approximately 3,500 wagons were built by the end of the war. After 1945, the welded rail carriages were distributed throughout half of Europe. In France, the equipping of these carriages with new bogies is still common. At the end of the war, DB had approximately 1,400 wagons in the inventory and it is estimated that DR had about 500. Both railway companies continued to use the wagons for a long period of time and they were only withdrawn in the 1980s. Even in 1979, DB had over 1,000 of the wagons bearing the R 672 designation in use. The original wagons were withdrawn earlier in the DR. However, the lack of wagons in the 1980s lead to the last R 672 wagons being purchased from DB. DR designated them as Rkk [3811] and used them until the slump in traffic volume in 1990. Model Brake blocks in wheel plane Individually mounted axle brake rod Individually mounted axle box cover Individually mounted brake systems True to original frame construction Die-cast zinc floor Insertable stakes individually enclosed
On order, shipped within 10-15 days
Prototype When the DRG [Deutsche Reichsbahn-Gesellschaft] was founded, a large quantity of rail carriages according to the Prussian standards were assumed meaning that, due to the modest financial means, there was no opportunity to procure high quantities of succession models. Although a 4-axle rail carriage was taken into consideration during the set-up of replacement construction drawings, only a limited amount of 95 units were built. Demand for a new 4-axle rail carriage only grew with the emergence of welding technology and the armament of the German Reich. Consequently, multiple prototypes and ranges with numerous differences were created in quick succession. In 1934, SEAG supplied the first two trial wagons. They were produced using St 52 and also had a removable wooden or steel brakeman’s cab respectively. The further deliveries up until 1939 were also produced using St 52, had three cross-members and seven stake pairs. The brakeman’s cab was removable. An amended variant was built from 1941 onwards. This now consisted of the weaker St 37 which meant that a fourth cross-member had to be included. Accordingly, there were now eight lateral stake pairs. For vehicle transports, the brakeman’s cab only had a foldable platform railing. At the request of the Wehrmacht, all of the older wagons had to be converted in this manner. The first deliveries boasted a welded box bogie but all later deliveries were equipped with the press plate bogies. In addition to the deliveries to the DR, the Wehrmacht also received wagons and used them for military purposes, e.g. in the trains of the mobile V2 ramps. In total, approximately 3,500 wagons were built by the end of the war. After 1945, the welded rail carriages were distributed throughout half of Europe. In France, the equipping of these carriages with new bogies is still common. At the end of the war, DB had approximately 1,400 wagons in the inventory and it is estimated that DR had about 500. Both railway companies continued to use the wagons for a long period of time and they were only withdrawn in the 1980s. Even in 1979, DB had over 1,000 of the wagons bearing the R 672 designation in use. The original wagons were withdrawn earlier in the DR. However, the lack of wagons in the 1980s lead to the last R 672 wagons being purchased from DB. DR designated them as Rkk [3811] and used them until the slump in traffic volume in 1990. Model Brake blocks in wheel plane Individually mounted axle brake rod Individually mounted axle box cover Individually mounted brake systems True to original frame construction Die-cast zinc floor Insertable stakes individually enclosed
On order, shipped within 10-15 days
Prototype Based on the UIC standard coach Gmhs 53, DB developed a 2-m longer waggon which otherwise complied with the UIC requirements in all its equipment features. Unlike its predecessor, it already had the newly standardised 2-m-wide loading door. At the time, UIC was not able to agree on a larger standard design, so this emerged only later in the form of the Glmms 61. Therefore, the waggon - designated Glm(e)hs 50 - was only a little longer than the pre-war large-capacity covered freight cars, which caused a great deal of controversy even at the time of construction. Even then, there were demands for a waggon with a loading length of at least 12.5 m, which meant the enlargement of the loading space did not go far enough for many customers, while others considered the waggons were too far removed from UIC requirements. Despite all these issues, some 12,000 waggons were built from 1953 – 1958 – up to 1954 with board walls, then with plate walls. Some one quarter of all waggons were fitted with a handbrake, at first with the characteristic sheet metal brakeman's cab. At least 700 waggons featured electric heating so that they could compete in express goods traffic in passenger trains. Some waggons were rented long-term and painted with advertising of the renting company. By the mid-seventies, the waggons with board walls had been decommissioned or upgraded with plate walls. Since 1965, the Glm(e)hs 50 were designated Gbrs(-v) 245, in 1980 after the heating pipes were mostly removed, they were renamed Gos(-uv) 245. Then, in the 80s, the inventory started to be reduced, although larger inventories were sold to DR In 1997, 35 waggons were still in the inventory, and the last three were taken out of service in 2000. Model Brake blocks in wheel plane Bogie with three-point support Individually mounted axle brake rod Individually mounted brake systems True to scale narrow frame Metal axle holders Wheelsets with inside contours
On order, shipped within 10-15 days
Prototype Of the six-axle flat cars with low sides acquired from 1952 by the DR, the DB took over 1,044 units and described them as Samm 451. The cars were a speciality of the Eastern European railways; such types of car construction had not previously been available in the West. The cars, originally intended for the transport of super heavy tracked vehicles during troop transports, were mainly used at the end of their life cycle as construction freight cars for transporting rubble, gravel or excavated earth. Model Axle holders made of embossed sheet metal Individually mounted wheelchocks Fine replica of the wheel bearing Multi-part brake system True to original car bottom Wheelsets with inside contours
On order, shipped within 10-15 days
Prototype In 1942, Tnf Berlin (Tnfs38) came into being as a simplified refrigerator car. The basic design was provided by the Glmhs Dresden, as a welded version. In contrast to these, the refrigerator cars were given 300 mm thick insulation and zinc plate inner lining in order to protect the internal wood cladding against moisture penetration. In order to ensure that the doors sealed completely, the double-leaf revolving doors were replaced with sliding doors. However, the most significant change was the vertical panelling combined with the typical white paint of the refrigerator cars. From the mid-1950s onwards, the German Federal Railway (DB) carried out several design modifications and modernisation work on the coaches it had acquired. The maintenance-intensive wheelsets with slide bearings were replaced with roller bearings; car bodies were rebuilt with the same design if their insulating properties were inadequate. As a result, the coaches retained their main dimensions; however, the eye-catching car body frame was now hidden under horizontal panelling, and later even under laminated wood panelling. New refrigerator car developments at DB made it possible for private breweries to purchase a variety of cars from DB and use them for transporting their beer. Since these were private cars belonging to specific breweries, in most cases they were decorated with the company’s own advertising. Model Axle brake frame with brake blocks in wheel plane Individually mounted brake systems Individually mounted handle bars Individually mounted wheelchocks Individually mounted steps NEM-standard short-coupling Metal wheels True to original frame construction Wheelsets with inside contours Perforated car body supports True to original construction differences
On order, shipped within 10-15 days