Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Rolling Stock

Locomotives, multiple units, coaches and wagons, new and pre-owned, from Z to G, checked by modellers.
Filter products
H0 Covered Freight Car Gmhs35 "EUROP" SAAR
Brawa 50728 Scale H0
H0 Covered Freight Car Gmhs35 "EUROP" SAAR

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Glms ÖBB
Brawa 50729 Scale H0
H0 Covered Freight Car Glms ÖBB

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car K "EUROP" SNCF
Brawa 50730 Scale H0
H0 Covered Freight Car K "EUROP" SNCF

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Gmhs SNCB
Brawa 50731 Scale H0
H0 Covered Freight Car Gmhs SNCB

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Gmhs35 "Linde" DB
Brawa 50733 Scale H0
H0 Covered Freight Car Gmhs35 "Linde" DB

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car KKus "EUROP" CFL
Brawa 50734 Scale H0
H0 Covered Freight Car KKus "EUROP" CFL

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Gmhs BBÖ
Brawa 50735 Scale H0
H0 Covered Freight Car Gmhs BBÖ

Prototype The East-German National Railway (Deutsche Reichsbahn) was constantlystriving to expand and upgrade its vehicle fleet. The Gm(h)s Bremen can thus be seen as the successor to the Gms Oppeln design. Representing the state of the art, the Gm(h)s Bremen wagons were manufactured from 1943 onwards in a welded design and had an extremely long wheelbase of seven metres to ensure the required smooth running. In addition, 260 mm-high solebars were used for the first time, which were lighter and reduced costs by around 25% compared to the predecessor design, the Gms Oppeln. The exact number of wagons delivered by the end of the war is unknown. Based on the existing inventories, however, it can be assumed that at least 7,230 units were acquired by various state railways. In 1949, with growing transport volumes creating an urgent need to replace the large numbers of goods wagons lost during the war, the head office of the Reichsbahn in the British/US zone placed new orders that prompted the resumption of production of the Gm(h)s 35. In terms of the design, there were only minor changes compared to the original version. Without doubt, the most striking of these were the new vertical strut on the loading door and the omission of the front diagonals. The Deutsche Bundesbahn’s (DB) inventory was thus expanded by an additional 5,925 Gm(h)s wagons by the end of 1950. In the Soviet zone, the Deutsche Reichsbahn resumed production at the end of 1945 and classified these wagons as Gmhs 11. The Reichsbahn accumulated a total stock of about 800 wagons of this type, of which a large number were modernised at the Reichsbahn repair shed Magdeburg from 1967 onwards. The upgrades included UIC sliding loading doors and ventilation hatches as well as cladding on the upper third of the side panels. The wagons were also fitted with metal roofs and converted to wheel sets with roller bearings. Model Metal axle bearing Different design of the car bodies True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails, steps and brake systems Individually mounted axle brake rod Perforated car body supports

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Covered Freight Car Gms ÖBB
Brawa 50738 Scale H0
H0 Covered Freight Car Gms ÖBB

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Kf "EUROP" SNCF
Brawa 50739 Scale H0
H0 Covered Freight Car Kf "EUROP" SNCF

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Gms 30 NS
Brawa 50740 Scale H0
H0 Covered Freight Car Gms 30 NS

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Zr NS
Brawa 50741 Scale H0
H0 Covered Freight Car Zr NS

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Grhs DRG
Brawa 50743 Scale H0
H0 Covered Freight Car Grhs DRG

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Gms 30 DB
Brawa 50744 Scale H0
H0 Covered Freight Car Gms 30 DB

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Gmrhs 30 DB
Brawa 50745 Scale H0
H0 Covered Freight Car Gmrhs 30 DB

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Gms 30 DB
Brawa 50746 Scale H0
H0 Covered Freight Car Gms 30 DB

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Gms ÖBB
Brawa 50747 Scale H0
H0 Covered Freight Car Gms ÖBB

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Grhs DR
Brawa 50748 Scale H0
H0 Covered Freight Car Grhs DR

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car (Mosw) Mso DR
Brawa 50749 Scale H0
H0 Covered Freight Car (Mosw) Mso DR

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Covered Freight Car Kf SNCF
Brawa 50750 Scale H0
H0 Covered Freight Car Kf SNCF

Prototype The introduction of welding technology from 1933 onwards increasingly made the Deutsche Reichsbahn (DR) switch to joining the components of their wagons by welding instead of riveting. One of the main advantages of welding technology was the weight saving which could then be used for increasing the cargo weight. In order to respond to the demand for higher speeds in part-load traffic as well, the DR developed the "Gs Oppeln", starting in 1936. Due to its wheel base of 6000mm, its maximum permissible speed could be fixed at 90 km/h. In addition to the missing junction plates that were made superfluous by the welding technology, this wagon type mainly differed in the pointed truss frame required due to the long wheel base. The increasing need for goods wagons due to the war led to the mass production of the "Gs Oppeln" from 1938 onwards. As a result, about 28,000 wagons without and 6,100 wagons with handbrake were built in the following years. Many of the wagons were equipped with a steam heating or even an electric heating system and could therefore be used as part-load wagons in semi-fast and express trains without any problems. After the end of World War II, the wagons were distributed all over Europe and could be found, for example, in the service of the railway administrations of Austria, Czechoslovakia, Poland, or Belgium. The reorganisation of the vehicle numbers of the young Deutsche Bundesbahn in the early fifties of the last century led to the change of "Gs Oppeln" into "Gms 30". Some of the wagons even came into the EUROP wagon pool, thus serving on an international basis. With the emergence of the first newly built goods wagons at the end of the fifties, a decision was made against an expensive general overhaul of the wagons. When the UIC numbering system was introduced, the existing wagons were re-numbered into "Glms 200", and some of them survived until 1979. Model Metal axle bearing Bogie with three-point support True to original frame construction Individually mounted axle box cover Brake blocks in wheel plane Individually mounted handrails Individually mounted steps Individually mounted axle brake rod Individually mounted brake systems Perforated car body supports

Regular price: CHF 45.05

On order, shipped within 10-15 days

H0 Tank Car 2-axle Z [P] DRG
Brawa 50751 Scale H0
H0 Tank Car 2-axle Z [P] DRG

Prototype In the mid-1930ies, the progress in lightweight construction led to new generations in wagon building in rapid succession. The introduction of welded tanks allowed weight savings, the benefit of which was increased cargo weight. Consequently, the wheelbase of the classical two-axle tank wagon design was increased from 4.00 m to 4.50 m starting at the end of thirties. The running gear corresponded to the design which was simultaneously developed for the welded DR wagons, and was conspicuous by its long suspension springs for smooth running, even at higher velocities. The resulting design was built by many European wagon factories in very large numbers until 1943 – MAN alone, although no classical tank wagon manufacturer, delivered 2,250 units. In addition to a few private owners, the sham firms and camouflage organisations of the German Reich were predominantly supplied as part of the war preparations. These included the "Wissenschaftliche Forschungsgemeinschaft" ("Wifo") and various "oil associations" ("Oelvereine"). In another case, the wagon user was more clearly identified by the name "Wilhelmshaven Naval Dockyard"; these wagons were used for the fuel supply of the submarine fleet. In the aggregate, far more than 10,000 units of these wagons with tanks of 20 m3, 22 m3 and 26.5 m3 were probably built. After the war, they were scattered all over Europe and, as a result, came into the possession of many mineral oil industry companies as private wagons. In addition to the classical grey-and-black paint jobs, many wagons were given conspicuous advertising paint jobs from white and yellow (Mobil / Shell) to green and blue (Texaco / Aral). The last wagons were still being used in 1989 in the fleet of the GDR‘s Deutsche Reichsbahn. Model Metal axle holders Bogie with three-point support Multi-part brake system Brake blocks in wheel plane Individually mounted axle box cover Free standing ladders Individually mounted railing

Regular price: CHF 40.50

On order, shipped within 10-15 days

H0 Tank Car 2-axle R CSD
Brawa 50752 Scale H0
H0 Tank Car 2-axle R CSD

Prototype In the mid-1930ies, the progress in lightweight construction led to new generations in wagon building in rapid succession. The introduction of welded tanks allowed weight savings, the benefit of which was increased cargo weight. Consequently, the wheelbase of the classical two-axle tank wagon design was increased from 4.00 m to 4.50 m starting at the end of thirties. The running gear corresponded to the design which was simultaneously developed for the welded DR wagons, and was conspicuous by its long suspension springs for smooth running, even at higher velocities. The resulting design was built by many European wagon factories in very large numbers until 1943 – MAN alone, although no classical tank wagon manufacturer, delivered 2,250 units. In addition to a few private owners, the sham firms and camouflage organisations of the German Reich were predominantly supplied as part of the war preparations. These included the "Wissenschaftliche Forschungsgemeinschaft" ("Wifo") and various "oil associations" ("Oelvereine"). In another case, the wagon user was more clearly identified by the name "Wilhelmshaven Naval Dockyard"; these wagons were used for the fuel supply of the submarine fleet. In the aggregate, far more than 10,000 units of these wagons with tanks of 20 m3, 22 m3 and 26.5 m3 were probably built. After the war, they were scattered all over Europe and, as a result, came into the possession of many mineral oil industry companies as private wagons. In addition to the classical grey-and-black paint jobs, many wagons were given conspicuous advertising paint jobs from white and yellow (Mobil / Shell) to green and blue (Texaco / Aral). The last wagons were still being used in 1989 in the fleet of the GDR‘s Deutsche Reichsbahn. Model Metal axle holders Bogie with three-point support Multi-part brake system Brake blocks in wheel plane Individually mounted axle box cover Free standing ladders Individually mounted railing

Regular price: CHF 40.50

On order, shipped within 10-15 days

H0 Tank Car 2-axle Z [P] "Persil" DB
Brawa 50754 Scale H0
H0 Tank Car 2-axle Z [P] "Persil" DB

Prototype In the mid-1930ies, the progress in lightweight construction led to new generations in wagon building in rapid succession. The introduction of welded tanks allowed weight savings, the benefit of which was increased cargo weight. Consequently, the wheelbase of the classical two-axle tank wagon design was increased from 4.00 m to 4.50 m starting at the end of thirties. The running gear corresponded to the design which was simultaneously developed for the welded DR wagons, and was conspicuous by its long suspension springs for smooth running, even at higher velocities. The resulting design was built by many European wagon factories in very large numbers until 1943 – MAN alone, although no classical tank wagon manufacturer, delivered 2,250 units. In addition to a few private owners, the sham firms and camouflage organisations of the German Reich were predominantly supplied as part of the war preparations. These included the "Wissenschaftliche Forschungsgemeinschaft" ("Wifo") and various "oil associations" ("Oelvereine"). In another case, the wagon user was more clearly identified by the name "Wilhelmshaven Naval Dockyard"; these wagons were used for the fuel supply of the submarine fleet. In the aggregate, far more than 10,000 units of these wagons with tanks of 20 m3, 22 m3 and 26.5 m3 were probably built. After the war, they were scattered all over Europe and, as a result, came into the possession of many mineral oil industry companies as private wagons. In addition to the classical grey-and-black paint jobs, many wagons were given conspicuous advertising paint jobs from white and yellow (Mobil / Shell) to green and blue (Texaco / Aral). The last wagons were still being used in 1989 in the fleet of the GDR‘s Deutsche Reichsbahn. Model Metal axle holders Bogie with three-point support Multi-part brake system Brake blocks in wheel plane Individually mounted axle box cover Free standing ladders Individually mounted railing

Regular price: CHF 40.50

On order, shipped within 10-15 days

H0 Lidded Freight Car K25 DB
Brawa 50776 Scale H0
H0 Lidded Freight Car K25 DB

Prototype For the transport of moisture-sensitive goods, such as lime, the railways introduced so-called “Lidded Freight Cars” in various designs from a very early stage. In the second half of the 1920s, the development of this car type resulted in the K Elberfeld 80 001 ff., which met the requirements for the “Austauschbauart” (a design based on standardised components) that were valid at that time, and was standardised accordingly. The freight car had a length of 8.1 m (without handbrake) and 8.8 m (with handbrake), as well as the short 4 m wheel base that was typical for this period and had a maximum load of 17.5 t. In order to withstand this weight, the side panels and hinge lid were strengthened with prominent crossed beads. While the original paint was RAL 8012, with the undercarriage and offset fittings in RAL 9005, this quickly changed to light grey streaks when loaded with lime. The 991 freigt cars delivered by 1933 were also the last cars to be built in series. Although the lidded freight cars could be loaded mechanically, they could only be unloaded manually. As a result, the development of selfunloading cars for the transport of similar goods was already underway in the days of the Reichsbahn, and there were no significant new developments after the K25. Nevertheless, the vehicles classified by the Bundesbahn (Federal Railway) as K25 remained in regular service until the end of the 1960s and, in isolated cases, for even longer as service vehicles. Model Metal axle holders interchangeable type Individually mounted brake systems True to original construction differences Finely engraved rivets True to scale construction

Regular price: CHF 47.75

On order, shipped within 10-15 days

H0 Lidded Freight Car K DRG
Brawa 50777 Scale H0
H0 Lidded Freight Car K DRG

Prototype For the transport of moisture-sensitive goods, such as lime, the railways introduced so-called “Lidded Freight Cars” in various designs from a very early stage. In the second half of the 1920s, the development of this car type resulted in the K Elberfeld 80 001 ff., which met the requirements for the “Austauschbauart” (a design based on standardised components) that were valid at that time, and was standardised accordingly. The freight car had a length of 8.1 m (without handbrake) and 8.8 m (with handbrake), as well as the short 4 m wheel base that was typical for this period and had a maximum load of 17.5 t. In order to withstand this weight, the side panels and hinge lid were strengthened with prominent crossed beads. While the original paint was RAL 8012, with the undercarriage and offset fittings in RAL 9005, this quickly changed to light grey streaks when loaded with lime. The 991 freigt cars delivered by 1933 were also the last cars to be built in series. Although the lidded freight cars could be loaded mechanically, they could only be unloaded manually. As a result, the development of selfunloading cars for the transport of similar goods was already underway in the days of the Reichsbahn, and there were no significant new developments after the K25. Nevertheless, the vehicles classified by the Bundesbahn (Federal Railway) as K25 remained in regular service until the end of the 1960s and, in isolated cases, for even longer as service vehicles. Model Metal axle holders interchangeable type Individually mounted brake systems True to original construction differences Finely engraved rivets True to scale construction

Regular price: CHF 47.75

On order, shipped within 10-15 days