Locomotives
V100 1063, Era III, DC/AC Removable roof held in place by magnets (Note: do not lift the model by the roof!) Finely detailed, multi-colour cabs, engine driver figure Sprung buffers Pipette for filling the smoke generator is included The minimum radius for operation is 360 mm. Length over the buffers V100.10/Class 211 = 139 mm, Class 212 = 141.4 mm As the smaller sister of the two-engined V200, the DB developed the single-engined V100 for light main-line duties. Both shared the same diesel-hydraulic transmission. The 1955 type programme included the V100, which promised simplified maintenance thanks to its recessed bonnets, a safe working environment for shunters, and, with 1,100 hp, adequate reserves for branch-line service. The mechanical equipment and gearbox had already been proven in the series V200.0, built from 1956, and some teething troubles had been resolved by the time the six pre-production V100 locomotives were ready for test runs in 1958. Following the conclusion of those trials and various design changes, series deliveries began with V100 008. The DB procured 364 examples of the 1,100 hp locomotive, later designated V100.10. In the meantime, V100 006 had had its Maybach MD 650 diesel engine of 1,100 hp replaced by the 1,350 hp Mercedes twelve-cylinder engine MB 835 Ab. Initially, however, the less powerful MB 820 Bb and MD 650 engines were fitted. As operational requirements called for more powerful locomotives, the DB procured a further 370 examples from 1962 onwards of the 1,350 hp version, classified as class V100.20 (later BR 212). This differs from the V100.10 (later BR 211) primarily by its longer front bonnet with a revised cooling system. As the V100.10 locomotives frequently worked at the limit of their output, their reliability declined, and from 1970 onwards a large-scale programme began to replace the engine with the more powerful MTU 12V 652 TA10, which had proved itself in the V100.20 from the factory since 1962. By the 1980s, approximately one third of the class 211 fleet had been fitted with the more powerful engine. A visually distinctive feature was the clip-on snowploughs carried, at least for a time, by around 140 of the 211 and 120 of the 212. Some 55 locomotives of class 211 and 230 examples of class 212 were equipped with push-pull and multiple-traction control. More than 150 examples of both types withdrawn by the DB found new homes in France, and more than 50 further examples in Italy. The Austrian ÖBB addressed a temporary locomotive shortage with 34 class 211 locomotives classified as BR 2048, keeping them in service until 2004. Today, numerous class 211, 212, and 213 locomotives can also be found with private railways in Germany.
- 2-rail, direct current
- 3-rail, alternating current
On order, lead time to be confirmed
Removable roof held by magnets (Note: do not lift the model by the roof!)
- 2-rail, direct current
- 3-rail, alternating current
On order, lead time to be confirmed
Removable roof held by magnets (Note: do not lift the model by the roof!)
- 2-rail, direct current
- 3-rail, alternating current
On order, lead time to be confirmed
Removable roof held by magnets (note: do not lift the model by the roof!)
- 2-rail, direct current
- 3-rail, alternating current
On order, lead time to be confirmed
Removable roof held by magnets (Note: do not lift the model by the roof!)
- 2-rail, direct current
- 3-rail, alternating current
On order, lead time to be confirmed
80 031 DB, black, DC/AC In the Deutsche Reichsbahn-Gesellschaft's standard locomotive programme for steam locomotives, there was also a three-axle class for heavy shunting duties. For this class, the DRG stipulated a maximum axle load of 17.5 t, which was only moderately exceeded at 18.1 t during acceptance, thanks to several tricks. This made the best possible use of the track facilities at marshalling yards and industrial areas close to major cities. In contrast to the numerous locomotives still dating from the era of the state railways, which were mostly larger, the class 80 was more powerful and at the same time more economical. On account of its imposing boiler, the three-coupled locomotive earned the nickname "Bulli". Despite the undeniable advantages of the modern design, the DRG, owing to the difficult economic situation, limited production to the 39 examples procured in 1928 and 1929. The locomotives bustled about the tracks at a maximum permitted speed of 45 km/h, mostly at passenger stations. By 1966, the reliable locomotives had disappeared from the marshalling yards of both German state railways. The V60 in both variants delivered similar haulage performance but was even more versatile in use owing to its higher maximum speed. At not even 40 years old, however, the class 80 locomotives had not yet been consigned to the scrapheap. Both state railways used the Bullis in repair works or sold them to industrial concerns or coal mines, which gratefully made use of the proven locomotives. A handful of class 80s, for example, toiled away in coal mines in the Ruhr district. There they were even used on works internal passenger trains. The last operational Bullis were 80 036 and 80 039, transferred to the Veluwsche Stoomtrein Maatschappij (VSM) in the Netherlands by the heritage railway Museumseisenbahn Hamm. A special status belongs to 80 009 of the Deutsche Reichsbahn, which was the only state railway locomotive to be sold to a private individual during the GDR era. The engine driver Klaus Hollenbach acquired the locomotive with great difficulty in 1981, transferred it under its own power, and built an engine shed and a short "private siding" on his own property for his 80 009, which was lifted onto the tracks in 1982 using two mobile cranes.
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
Diesel loco, 260 610 DB, blue-cream, Era IV, prototype around 1980, Sound+Smoke, el. Coupler, DC/AC (replaces Art.-No: 31411) Starting in 1956 the DB (Deutsche Bundesbahn) commenced the procurement of the three-axle shunting locomotive class V60 in order to modernize shunting operations. It was decided to employ a drive system with coupling rods and a jack shaft. Its maximum speed of 60 km/h in mainline gear matched the then common speed of long distance freight trains. The coal-fired oven (so called Dofa heater) only served for keeping the engine of a parked V60 at a suitable temperature. As from the 1990-ies the DB replaced these heaters with externally powered electric heaters. The DB actually differentiated the serial locomotives between light weight and heavy types. Externally one could not detect any difference. The heavy type with 54 t is constructed with a stronger frame compared to the lighter version with 48 t. With the advent of the computer suitable numbering system in 1968, the DB assigned the lighter version as class 260 and the heavy type as class 261. In 1987 the engine was reclassified as a minor locomotive (Kleinlokomotive - literally: small locomotive or locomotors). Class 260 became class 360 and the 261s became 361s. Its categorisation as a Kleinlok saved staff costs, because the railway no longer had to employ "engine drivers", but only "Kleinlok operators", i.e.: specially trained shunting personnel. The locomotives equipped with automatic coupler (AK) and radio control were reclassified as class 364 (light weight version) and class 365 (heavy type). Class 362 and 363 were only designated in 1992 and denominate locomotives equipped with the Caterpillar engine 3412 DI-TA, which was installed instead of the original Maybach GTO 6 / GTO 6A. The ESU model of the DB class V60 is completely new! Chassis, body, motor, gearbox, centre pick-up including its holding fixture, smoke generator, lighting, digital coupler, speaker as well as all details have been developed from scratch. The headlight inserts have vertical engravings in order to match the appearance of DB standard lanterns. The conversion from AC (as delivered) to DC mode is accomplished by pulling off the centre pick-up and by activating a small sliding switch right in front of the forward axle. The digitally remote controlled electromagnetic coupler (shunting coupler) is inserted into the standard coupler shaft as per NEM 362. The mounting height of the coupler can be adjusted in two steps. If necessary it can be removed and replaced by another (non-digital) coupler without soldering. The newly designed smoke generator supplies a larger amount of exhaust fumes. Of course, the LokSound 5 decoder is completely new. Smooth running characteristics and a number of useful functions and potential settings offer plenty of options for the operation oriented model train enthusiast. There is a function “heavy train” where acceleration and deceleration time are doubled and the motor acoustically works with higher revs. When activating the “locomotive brake”, the locomotive changes to idle and slows down a bit faster than normal – if required, right down to a standstill. This function works independently from the throttle setting. In shunting mode, the locomotive accelerates and slows down faster than in normal mode. Model LokSound decoder for DCC with RailComPlus®, Motorola®, M4 and Selectrix Automatic registration at command stations with RailComPlus® or mfx® functionality Universal electronics with plug-in centre pick-up Newly developed, aerodynamically optimised, load dependent smoke generator synchronised with LokSound Two sugar cube speakers with large sound enclosure under the hood 31 special functions PowerPack storage capacitor for uninterrupted power supply Powerful coreless motor with flywheel Digital remote control for coupler in NEM shaft Prototypical headlights Separately switchable shunting lighting Cab lighting and control panel lighting may be separately switched Switchable under-carriage lighting Engraved fibre-optic light guide Metal chassis and body Perforated fan grills in long hood Robust yet filigree grab irons off metal and plastic Multicoloured cab interior with engineer figure Length over buffers = 121 mm Detail Videos Ihr Browser kann dieses Video nicht wiedergeben. Art.No. Delivery 31423 Diesel loco, Post Lok 5, red, Ep. IV, prototype around 1987, Sound+Smoke, el. Coupler, DC/AC in stock 31741 Diesel loco, 260 610 DB, blue-cream, Era IV, prototype around 1980, Sound+Smoke, el. Coupler, DC/AC (replaces Art.-No: 31411) in stock 31742 Diesel loco, 362 614 DB, traffic red, Era VI, prototype around 2014, Sound+Smoke, el. Coupler, DC/AC in stock 31743 Diesel loco, V60 114 DB/DFS, oldred, Era VI, prototype around 2020, Sound+Smoke, el. Coupler, DC/AC in stock 31744 Diesel loco, 261 652 DB, oldred, Era IV, prototype around 1975, Sound+Smoke, el. Coupler, DC/AC in stock
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
Diesel loco, 362 614 DB, traffic red, Era VI, prototype around 2014, Sound+Smoke, el. Coupler, DC/AC Starting in 1956 the DB (Deutsche Bundesbahn) commenced the procurement of the three-axle shunting locomotive class V60 in order to modernize shunting operations. It was decided to employ a drive system with coupling rods and a jack shaft. Its maximum speed of 60 km/h in mainline gear matched the then common speed of long distance freight trains. The coal-fired oven (so called Dofa heater) only served for keeping the engine of a parked V60 at a suitable temperature. As from the 1990-ies the DB replaced these heaters with externally powered electric heaters. The DB actually differentiated the serial locomotives between light weight and heavy types. Externally one could not detect any difference. The heavy type with 54 t is constructed with a stronger frame compared to the lighter version with 48 t. With the advent of the computer suitable numbering system in 1968, the DB assigned the lighter version as class 260 and the heavy type as class 261. In 1987 the engine was reclassified as a minor locomotive (Kleinlokomotive - literally: small locomotive or locomotors). Class 260 became class 360 and the 261s became 361s. Its categorisation as a Kleinlok saved staff costs, because the railway no longer had to employ "engine drivers", but only "Kleinlok operators", i.e.: specially trained shunting personnel. The locomotives equipped with automatic coupler (AK) and radio control were reclassified as class 364 (light weight version) and class 365 (heavy type). Class 362 and 363 were only designated in 1992 and denominate locomotives equipped with the Caterpillar engine 3412 DI-TA, which was installed instead of the original Maybach GTO 6 / GTO 6A. The ESU model of the DB class V60 is completely new! Chassis, body, motor, gearbox, centre pick-up including its holding fixture, smoke generator, lighting, digital coupler, speaker as well as all details have been developed from scratch. The headlight inserts have vertical engravings in order to match the appearance of DB standard lanterns. The conversion from AC (as delivered) to DC mode is accomplished by pulling off the centre pick-up and by activating a small sliding switch right in front of the forward axle. The digitally remote controlled electromagnetic coupler (shunting coupler) is inserted into the standard coupler shaft as per NEM 362. The mounting height of the coupler can be adjusted in two steps. If necessary it can be removed and replaced by another (non-digital) coupler without soldering. The newly designed smoke generator supplies a larger amount of exhaust fumes. Of course, the LokSound 5 decoder is completely new. Smooth running characteristics and a number of useful functions and potential settings offer plenty of options for the operation oriented model train enthusiast. There is a function “heavy train” where acceleration and deceleration time are doubled and the motor acoustically works with higher revs. When activating the “locomotive brake”, the locomotive changes to idle and slows down a bit faster than normal – if required, right down to a standstill. This function works independently from the throttle setting. In shunting mode, the locomotive accelerates and slows down faster than in normal mode. Model LokSound decoder for DCC with RailComPlus®, Motorola®, M4 and Selectrix Automatic registration at command stations with RailComPlus® or mfx® functionality Universal electronics with plug-in centre pick-up Newly developed, aerodynamically optimised, load dependent smoke generator synchronised with LokSound Two sugar cube speakers with large sound enclosure under the hood 31 special functions PowerPack storage capacitor for uninterrupted power supply Powerful coreless motor with flywheel Digital remote control for coupler in NEM shaft Prototypical headlights Separately switchable shunting lighting Cab lighting and control panel lighting may be separately switched Switchable under-carriage lighting Engraved fibre-optic light guide Metal chassis and body Perforated fan grills in long hood Robust yet filigree grab irons off metal and plastic Multicoloured cab interior with engineer figure Length over buffers = 121 mm Detail Videos Ihr Browser kann dieses Video nicht wiedergeben. Art.No. Delivery 31423 Diesel loco, Post Lok 5, red, Ep. IV, prototype around 1987, Sound+Smoke, el. Coupler, DC/AC in stock 31741 Diesel loco, 260 610 DB, blue-cream, Era IV, prototype around 1980, Sound+Smoke, el. Coupler, DC/AC (replaces Art.-No: 31411) in stock 31742 Diesel loco, 362 614 DB, traffic red, Era VI, prototype around 2014, Sound+Smoke, el. Coupler, DC/AC in stock 31743 Diesel loco, V60 114 DB/DFS, oldred, Era VI, prototype around 2020, Sound+Smoke, el. Coupler, DC/AC in stock 31744 Diesel loco, 261 652 DB, oldred, Era IV, prototype around 1975, Sound+Smoke, el. Coupler, DC/AC in stock
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
Diesel loco, V60 114 DB/DFS, oldred, Era VI, prototype around 2020, Sound+Smoke, el. Coupler, DC/AC Starting in 1956 the DB (Deutsche Bundesbahn) commenced the procurement of the three-axle shunting locomotive class V60 in order to modernize shunting operations. It was decided to employ a drive system with coupling rods and a jack shaft. Its maximum speed of 60 km/h in mainline gear matched the then common speed of long distance freight trains. The coal-fired oven (so called Dofa heater) only served for keeping the engine of a parked V60 at a suitable temperature. As from the 1990-ies the DB replaced these heaters with externally powered electric heaters. The DB actually differentiated the serial locomotives between light weight and heavy types. Externally one could not detect any difference. The heavy type with 54 t is constructed with a stronger frame compared to the lighter version with 48 t. With the advent of the computer suitable numbering system in 1968, the DB assigned the lighter version as class 260 and the heavy type as class 261. In 1987 the engine was reclassified as a minor locomotive (Kleinlokomotive - literally: small locomotive or locomotors). Class 260 became class 360 and the 261s became 361s. Its categorisation as a Kleinlok saved staff costs, because the railway no longer had to employ "engine drivers", but only "Kleinlok operators", i.e.: specially trained shunting personnel. The locomotives equipped with automatic coupler (AK) and radio control were reclassified as class 364 (light weight version) and class 365 (heavy type). Class 362 and 363 were only designated in 1992 and denominate locomotives equipped with the Caterpillar engine 3412 DI-TA, which was installed instead of the original Maybach GTO 6 / GTO 6A. The ESU model of the DB class V60 is completely new! Chassis, body, motor, gearbox, centre pick-up including its holding fixture, smoke generator, lighting, digital coupler, speaker as well as all details have been developed from scratch. The headlight inserts have vertical engravings in order to match the appearance of DB standard lanterns. The conversion from AC (as delivered) to DC mode is accomplished by pulling off the centre pick-up and by activating a small sliding switch right in front of the forward axle. The digitally remote controlled electromagnetic coupler (shunting coupler) is inserted into the standard coupler shaft as per NEM 362. The mounting height of the coupler can be adjusted in two steps. If necessary it can be removed and replaced by another (non-digital) coupler without soldering. The newly designed smoke generator supplies a larger amount of exhaust fumes. Of course, the LokSound 5 decoder is completely new. Smooth running characteristics and a number of useful functions and potential settings offer plenty of options for the operation oriented model train enthusiast. There is a function “heavy train” where acceleration and deceleration time are doubled and the motor acoustically works with higher revs. When activating the “locomotive brake”, the locomotive changes to idle and slows down a bit faster than normal – if required, right down to a standstill. This function works independently from the throttle setting. In shunting mode, the locomotive accelerates and slows down faster than in normal mode. Model LokSound decoder for DCC with RailComPlus®, Motorola®, M4 and Selectrix Automatic registration at command stations with RailComPlus® or mfx® functionality Universal electronics with plug-in centre pick-up Newly developed, aerodynamically optimised, load dependent smoke generator synchronised with LokSound Two sugar cube speakers with large sound enclosure under the hood 31 special functions PowerPack storage capacitor for uninterrupted power supply Powerful coreless motor with flywheel Digital remote control for coupler in NEM shaft Prototypical headlights Separately switchable shunting lighting Cab lighting and control panel lighting may be separately switched Switchable under-carriage lighting Engraved fibre-optic light guide Metal chassis and body Perforated fan grills in long hood Robust yet filigree grab irons off metal and plastic Multicoloured cab interior with engineer figure Length over buffers = 121 mm Detail Videos Ihr Browser kann dieses Video nicht wiedergeben. Art.No. Delivery 31423 Diesel loco, Post Lok 5, red, Ep. IV, prototype around 1987, Sound+Smoke, el. Coupler, DC/AC in stock 31741 Diesel loco, 260 610 DB, blue-cream, Era IV, prototype around 1980, Sound+Smoke, el. Coupler, DC/AC (replaces Art.-No: 31411) in stock 31742 Diesel loco, 362 614 DB, traffic red, Era VI, prototype around 2014, Sound+Smoke, el. Coupler, DC/AC in stock 31743 Diesel loco, V60 114 DB/DFS, oldred, Era VI, prototype around 2020, Sound+Smoke, el. Coupler, DC/AC in stock 31744 Diesel loco, 261 652 DB, oldred, Era IV, prototype around 1975, Sound+Smoke, el. Coupler, DC/AC in stock
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
Diesel loco, 261 652 DB, oldred, Era IV, prototype around 1975, Sound+Smoke, el. Coupler, DC/AC Starting in 1956 the DB (Deutsche Bundesbahn) commenced the procurement of the three-axle shunting locomotive class V60 in order to modernize shunting operations. It was decided to employ a drive system with coupling rods and a jack shaft. Its maximum speed of 60 km/h in mainline gear matched the then common speed of long distance freight trains. The coal-fired oven (so called Dofa heater) only served for keeping the engine of a parked V60 at a suitable temperature. As from the 1990-ies the DB replaced these heaters with externally powered electric heaters. The DB actually differentiated the serial locomotives between light weight and heavy types. Externally one could not detect any difference. The heavy type with 54 t is constructed with a stronger frame compared to the lighter version with 48 t. With the advent of the computer suitable numbering system in 1968, the DB assigned the lighter version as class 260 and the heavy type as class 261. In 1987 the engine was reclassified as a minor locomotive (Kleinlokomotive - literally: small locomotive or locomotors). Class 260 became class 360 and the 261s became 361s. Its categorisation as a Kleinlok saved staff costs, because the railway no longer had to employ "engine drivers", but only "Kleinlok operators", i.e.: specially trained shunting personnel. The locomotives equipped with automatic coupler (AK) and radio control were reclassified as class 364 (light weight version) and class 365 (heavy type). Class 362 and 363 were only designated in 1992 and denominate locomotives equipped with the Caterpillar engine 3412 DI-TA, which was installed instead of the original Maybach GTO 6 / GTO 6A. The ESU model of the DB class V60 is completely new! Chassis, body, motor, gearbox, centre pick-up including its holding fixture, smoke generator, lighting, digital coupler, speaker as well as all details have been developed from scratch. The headlight inserts have vertical engravings in order to match the appearance of DB standard lanterns. The conversion from AC (as delivered) to DC mode is accomplished by pulling off the centre pick-up and by activating a small sliding switch right in front of the forward axle. The digitally remote controlled electromagnetic coupler (shunting coupler) is inserted into the standard coupler shaft as per NEM 362. The mounting height of the coupler can be adjusted in two steps. If necessary it can be removed and replaced by another (non-digital) coupler without soldering. The newly designed smoke generator supplies a larger amount of exhaust fumes. Of course, the LokSound 5 decoder is completely new. Smooth running characteristics and a number of useful functions and potential settings offer plenty of options for the operation oriented model train enthusiast. There is a function “heavy train” where acceleration and deceleration time are doubled and the motor acoustically works with higher revs. When activating the “locomotive brake”, the locomotive changes to idle and slows down a bit faster than normal – if required, right down to a standstill. This function works independently from the throttle setting. In shunting mode, the locomotive accelerates and slows down faster than in normal mode. Model LokSound decoder for DCC with RailComPlus®, Motorola®, M4 and Selectrix Automatic registration at command stations with RailComPlus® or mfx® functionality Universal electronics with plug-in centre pick-up Newly developed, aerodynamically optimised, load dependent smoke generator synchronised with LokSound Two sugar cube speakers with large sound enclosure under the hood 31 special functions PowerPack storage capacitor for uninterrupted power supply Powerful coreless motor with flywheel Digital remote control for coupler in NEM shaft Prototypical headlights Separately switchable shunting lighting Cab lighting and control panel lighting may be separately switched Switchable under-carriage lighting Engraved fibre-optic light guide Metal chassis and body Perforated fan grills in long hood Robust yet filigree grab irons off metal and plastic Multicoloured cab interior with engineer figure Length over buffers = 121 mm Detail Videos Ihr Browser kann dieses Video nicht wiedergeben. Art.No. Delivery 31423 Diesel loco, Post Lok 5, red, Ep. IV, prototype around 1987, Sound+Smoke, el. Coupler, DC/AC in stock 31741 Diesel loco, 260 610 DB, blue-cream, Era IV, prototype around 1980, Sound+Smoke, el. Coupler, DC/AC (replaces Art.-No: 31411) in stock 31742 Diesel loco, 362 614 DB, traffic red, Era VI, prototype around 2014, Sound+Smoke, el. Coupler, DC/AC in stock 31743 Diesel loco, V60 114 DB/DFS, oldred, Era VI, prototype around 2020, Sound+Smoke, el. Coupler, DC/AC in stock 31744 Diesel loco, 261 652 DB, oldred, Era IV, prototype around 1975, Sound+Smoke, el. Coupler, DC/AC in stock
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
220 076, DB, dark red, DC/AC The V200 was THE locomotive face of the German Federal Railway (DB) in the 1950s. No other diesel locomotive shaped the image of the young DB as much as the long locomotive with its characteristic aluminium decorative strips, which tapered at the front ends into a stylised "V". The production locomotives built from 1956 onwards were fitted with 1,100 hp (at 1,500 rpm) 12-cylinder engines from Daimler-Benz (MB 820 Bb), MAN (12 V 18/21) or Maybach (MD 650). A Hagenuk steam heating boiler provided train heating, capable of heating an express train of ten to twelve coaches. A notable feature was the fitting of all V200.0 locomotives with multiple-unit control equipment, which enabled double-heading and push-pull operation. With Krauss-Maffei (V200 001–005, V200 026–086) and MaK (V200 006 to 025), only two manufacturers supplied the 86 locomotives to the DB. The MaK locomotives were clearly distinguishable at the front by a flatter version of the "V" compared with the Krauss-Maffei locomotives. The first allocations of production locomotives went to the motive power depots (Bw) at Frankfurt-Griesheim (15 locomotives), Hamburg-Altona (19), Hamm P (32) and Villingen/Schwarzwald (20). From the factory, V200 056 to 086 received simple DB logos on their sides instead of the prominent "Deutsche Bundesbahn" lettering. From the early 1970s onwards, the aluminium decorative strips were removed and the locomotives were given a decorative line as a dividing element between the red and grey areas. Three V200 locomotives were repainted in the 1970s in the then fashionable colours of ocean blue and ivory. The distinctive "V" on the front ends was omitted. After the DB had already withdrawn the Class 220 from service from 1978 onwards, it offered the locomotives, some of which were barely 20 years old, for sale to foreign railways. A total of 30 locomotives found buyers in Italy, France (Algeria) and Spain. Body and frame made of metal Open grille ventilators in the roof area, flat MaK "V" on the front ends Multicoloured cab with driver figure Prototypical partial view through the engine room Multi-part bogie fairings Separately applied handrails and steps Close coupler in a guided NEM pocket Five-pole ESU motor with two flywheels Drive via cardan/worm gearing to three axles, two traction tyres LokSound decoder for DCC, Motorola®, M4, and Selectrix operation Automatic registration with command stations featuring RailComPlus® or mfx® functionality PowerPack buffer capacitor for uninterrupted power supply Dual speaker with large sound capsule for the ultimate sound experience Universal electronics with plug-in pickup shoe and switch for changing between two-rail and centre-rail operation 2 smoke generators, synchronised with the LokSound; during shunting operations only one smoke generator is active Digitised original sounds of a locomotive with V 200 with Maybach diesel engines MD 650 Sensor-controlled sounds during slow curve negotiation Direction-dependent lighting changeover, train-end headlights can be switched off, shunting, cab, driver's desk and engine room lighting Brake sparks when braking hard Pipette for filling the smoke generator, buffer beam detail parts and a 2nd coupler are included The minimum radius for operation is 360 mm Length over the buffers = 209.7 mm
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
220 060, DB, ocean blue/beige, DC/AC The V200 was THE locomotive face of the German Federal Railway (DB) in the 1950s. No other diesel locomotive shaped the image of the young DB as much as the long locomotive with its characteristic aluminium decorative strips, which tapered at the front ends into a stylised "V". The production locomotives built from 1956 onwards were fitted with 1,100 hp (at 1,500 rpm) 12-cylinder engines from Daimler-Benz (MB 820 Bb), MAN (12 V 18/21) or Maybach (MD 650). A Hagenuk steam heating boiler served for train heating, capable of heating an express train of ten to twelve coaches. A particular feature was the fitting of all V200.0 locomotives with multiple-unit control, which enabled double-heading and push-pull operation. With Krauss-Maffei (V200 001–005, V200 026–086) and MaK (V200 006 to 025), only two manufacturers supplied the 86 locomotives to the DB. The MaK locomotives differed noticeably at the front by having a flatter version of the "V" compared to the Krauss-Maffei locomotives. The first allocations of production locomotives went to the motive power depots (Bw) of Frankfurt-Griesheim (15 locomotives), Hamburg-Altona (19), Hamm P (32) and Villingen/Schwarzwald (20). From the factory, V200 056 to 086 received simple DB logos on their sides instead of the prominent "Deutsche Bundesbahn" lettering. From the early 1970s, the aluminium decorative strips were removed and the locomotives were given a decorative line as a separation between the red and grey areas. Three V200 locomotives were repainted in the 1970s in the then fashionable colours of ocean blue and ivory. The distinctive "V" on the front ends was omitted. After the DB had already withdrawn the Class 220 from 1978 onwards, it offered the locomotives, some barely 20 years old, for sale to foreign railways. A total of 30 locomotives found buyers in Italy, France (Algeria) and Spain. Body and frame made of metal Open grille ventilators in the roof area, flat MaK "V" on the front ends Multicoloured cab with driver figure Prototypical partial view through the engine room Multi-part bogie fairings Separately applied handrails and steps Coupler in guided NEM pocket Five-pole ESU motor with two flywheels Drive via cardan/worm gearing to three axles, two traction tyres LokSound decoder for DCC, Motorola®, M4, and Selectrix operation Automatic registration with command stations featuring RailComPlus® or mfx® functionality PowerPack buffer capacitor for uninterrupted power supply Dual speaker with large sound capsule for the ultimate sound experience Universal electronics with plug-in pickup shoe and switch for changing between two-rail and centre-rail operation 2 smoke generators, synchronised with the LokSound; during shunting operations only one smoke generator is active Digitised original sounds of a locomotive with V 200 with Maybach diesel engines MD 650 Sensor-controlled sounds during slow curve negotiation Directional lighting changeover, the leading headlights can be switched off, shunting lighting, cab lighting, control desk lighting, and engine room lighting Brake sparks when braking hard Pipette for filling the smoke generator, buffer beam detail parts and a 2nd coupler are included The minimum radius for operation is 360 mm Length over the buffers = 209.7 mm
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
202 594 DB, traffic red, Era V, DC/AC The most widely built German main-line diesel locomotive class must, of course, have a place in the ESU range as a fully equipped H0 model. The features found on its DB sister are present here too. One particular challenge was to replicate the two traction motor cooling fans, which are controlled independently in the prototype, as separately switchable motors in the model as well. The etched fan covers allow the work of the fan wheels to be observed, supported acoustically by the corresponding sounds. To ensure that the crisp sound of the 12 KVD diesel engine comes across well, we fitted the loudspeaker with a so-called passive radiator and developed a sound chamber that makes the best possible use of the available space. It goes without saying that a sound-synchronised smoke generator, a bell-armature motor with flywheel, digital couplers at both ends, sprung buffers, and numerous lighting functions are all on board. As you have come to expect from ESU, we studied the prototype closely when designing our models and reproduced the details with minimal compromise. On locomotives fitted with a steam heating boiler, you will find the corresponding pipework; the ventilation grilles are made up of multiple parts; and the characteristic reflectors of the lower headlamps give the model a face even when the lighting is switched off. As with all our V100 models, the magnetically secured cab roof can be lifted off, and the personal equipment of the locomotive crew can be supplemented further as desired. A particularly large number of details are revealed by the running gear, especially in the light grey livery to TGL 1808. Deeply engraved bogie side frames, differently equipped depending on the variant, with real springs and open or covered areas beneath the frame according to type, impressively demonstrate the differences within the locomotive family. Except on the traffic red version, the Reichsbahn lettering and running number plate are included as etched parts. For the class 111 locomotives, which have a lower maximum speed in the prototype, we have of course not simply reduced the top speed in a blunt fashion, but have adjusted all CVs relevant to the running dynamics accordingly. NEW TOOLING Metal body and frame Digitally switchable coupler Situation-dependent and sequentially activated motor-driven cooling fans in the long hood Bell-armature motor with flywheel Drive via cardan/worm gearing to all four axles, two traction tyres LokSound 5 decoder for DCC, Motorola®, M4 and Selectrix operation Switchable smoke generator with smoke output synchronised to the LokSound Automatic registration with command stations featuring RailComPlus® or mfx® functionality Universal electronics with plug-in pickup shoe and sliding switch for changing over between two-rail and centre-rail operation PowerPack buffer capacitor for uninterrupted power supply High-quality speaker with a large sound capsule for the ultimate listening experience Digitalised original sounds of a 12 KVD 18/21 diesel engine Squealing sound via curve sensor when travelling slowly through curves Direction-dependent lighting changeover (the lights switch on one after another in a prototypical manner), leading headlights can be switched off, cab and driver's desk lighting Brake sparks during hard braking Separately applied handrails, steps partially open-framed Delicate multi-part grilles on the sides of the long nose Removable roof held in place by magnets (Note: do not lift the model by the roof!) Finely detailed, multi-colour cabs, engine driver figure Sprung buffers Pipette for filling the smoke generator is included The minimum radius for operation is 360 mm. Length over the buffers 110 = 160.2 mm, 111, 202 = 163.7 mm The Deutsche Reichsbahn of the GDR did not include a medium-power line diesel locomotive between the V60 and the V180 when drawing up its diesel locomotive type programme in the 1950s. When the need became acute in the early 1960s, VEB Lokomotivbau "Karl Marx" and the Elektrotechnische Werke "Hans Beimler" developed the V100 with the stipulation that as many assemblies as possible from the V60 and V180 should be used, the 100 standing for an output of approximately 1,000 hp. The three pre-production locomotives delivered in 1965 were initially fitted with only 900 hp twelve-cylinder engines of the type 12 KVD 18/21. The maximum speed was 100 km/h. After extensive testing, series production began as early as the following year. A total of 869 locomotives were built across several series, making the V100 the most-produced line locomotive of the DR. Already in the first years of service it became apparent that the V100 (or Class 110, as it was known from 1969 onwards in accordance with data-processing requirements) could not replace all steam locomotive classes with a similar operating profile. Through advances in engine development and the installation of charge-air cooling, the output and reliability of the 12 KVD type were improved. The final development stage of the 12 KVD engine was set at 1,100 kW, almost 400 kW more than in the first production series. For export, including to China, LEW derived the V100.3 sub-class from the V100, intended for heavy shunting duties and with a maximum speed of only 65 km/h. The locomotive now lettered as 111 002, belonging to Leipziger Dampf KulTour LDK, was delivered to the then Czechoslovakia in 1981. The massive horizontal pilot fitted with a warning livery below the buffer beam reveals that the locomotive does not originate from Deutsche Reichsbahn stock. LDK uses the 111, which always gleams as if brand new, in shunting service, or hires it out for engineering train duties. The version derived from the V100.3 for the DR and industrial railways in the GDR was designated V100.4. Although the locomotives carried ballast weights instead of a steam heating boiler, the orange four-axle machines could also be observed on passenger trains during the summer. As the transmission of the 111 did not fully prove itself in heavy shunting service, only 37 examples were built for the DR, with a further six for GDR industry. Nine locomotives equipped with a single-sided gangway bridge and power take-off flange worked the so-called ditch-clearing units GRE. The fluid reversing gearbox, better suited to the demands of shunting service, was tested from 1978 in two Class 110 locomotives. It did not enter series production until 1991 with Class 108, which, following the unification of the two German state railways, was subsequently designated Class 298. After the last V100 locomotives were withdrawn from Deutsche Bahn AG in the 2010s, a considerable number passed to private railway operators and heritage railways.
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
Removable roof held in place by magnets (Caution: Do not lift the model by the roof!)
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
Removable roof held in place by magnets (Caution: Do not lift the model by the roof!)
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
Removable roof held in place by magnets (Caution: Do not lift the model by the roof!)
- 2-rail, direct current
- 3-rail, alternating current
- Sound
On order, lead time to be confirmed
Z21 START newGen digital set: Diesel locomotive class 245 with passemger train, of the Deutsche Bahn. Contents: 1 digitally controlled Diesel locomotive class 245 2 double-deck coaches 1 Z21 START newGen 1 Z21 multiMAUS 1 plug-in power supply Suitable for use with the Z21 wireless Z21 WLANMAUS Gravel bed tracks for an oval track with a radius R1 (4 x 9100, 8 x 9120), electrical connection material. Size of track layout: 85 cm x 40 cm. Information Z21 START newGen Features With built-in Wi-Fi, setting it up and connecting is a breeze! Controls up to 9,999 DCC locomotive decoders Controls up to 2,048 DCC turnout decoders RailCom receiver Software updates via new update portal (more information will follow) Connections: X-BUS USB-C Technical informations Input voltage: 12-24 V Output voltage corresponds to 1 V below input voltage Output current: max. 3 A Analog locomotives: Not controllable Maximum number of trains: 100 vehicles simultaneously DCC locomotive decoder 14/28/128 speed steps F0 to F31 POM read & write Main track and programming track are on one output on the Z21 START newGen, as known from the z21start. RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen.
Pre-order, ships on release
Steam locomotive 01 200 of the Deutsche Bundesbahn. Operation condition: 1950s Used in high-quality express train services "Wagner" smoke deflectors Unobstructed view between boiler and chassis Tender 2'2' T 32 The two-cylinder engines of class 01 are considered the first express train locomotives to be produced according to the standard construction programme. The first construction lots had leading wheels with a diameter of 800 mm and were approved for a maximum speed of 120 km/h. Later models, starting from 01 102, were equipped with 1.000 mm leading wheels and reinforced brakes, allowing for an increased maximum speed of 130 km/h. The golden age of the class 01 locomotives began in 1934 with the summer timetable. The high level of commitment and performance expected from them in the following years posed significant challenges for both the locomotives and the personnel. After the Second World War, these standards were not achieved again until the introduction of electric locomotives and large-scale diesel locomotives. In 1935, locomotive 01 200 was transferred from Henschel to the Hof depot, and from there it was called upon to haul fast and express trains between Bamberg and Hof on the Schiefen Ebene line.
On order, shipped within 10-15 days
Steam locomotive 01 202 of the Verein Pacific 01 202. Version as a museum exhibit locomotive Smoke chamber door with central lock Elaborate printing on the boiler rings and wheel tires Additional alternator Version with open front apron and "Witte" smoke deflectors Unobstructed view between the boiler and chassis The express steam locomotive 01 202 is a living piece of engineering history. Built in 1936 by Henschel & Sohn in Kassel for the former Deutsche Reichsbahn, it later entered service with the Deutsche Bundesbahn after World War II, from which it was primarily used in southern Germany. Its final years in active service were spent at the Hof depot, where it frequently operated on the steep gradients of the inclined plane. On October 2, 1975, the 01 202 arrived in Switzerland. There, it was painstakingly restored to operating condition by Werner Bühlmann of Münsingen, together with a dedicated group of passionate, optimistic volunteers, working in their spare time without pay. Thanks to more than 20 years of continuous effort, the locomotive is now considered the finest operational specimen of the Class 01 and remains in remarkably well-maintained condition. Since 1991, the Pacific 01 202 Association has been responsible for all aspects of the locomotive's maintenance and operation.
On order, shipped within 10-15 days
Steam locomotive class 232 TC of the French State Railways. Round roof Die-cast metal chassis The SNCF purchased twenty-seven locomotives of type T18 from the Reichseisenbahnen in Alsace-Lorraine. The locomotives were built between 1915 and 1918 by the Vulcan works. They were stationed in Strasbourg, Haguenau, Sélestat, Colmar, and Mulhouse. Due to their incredible top speed of 100 km/h, large water reservoir, and much-appreciated smooth-running characteristics, they were mainly used in fast suburban traffic. The last 232 TCs quit regular services at the SNCF and were decommissioned in 1966.
On order, shipped within 10-15 days
Steam locomotive 23 071 of the Veluwsche Stoomtrein Maatschappij (VSM). Version as a museum exhibit locomotive Movable Heusinger control system The Class 23 locomotives were passenger train steam locomotives operated by the Deutsche Bundesbahn. Starting in 1950, a total of 105 units of this newly designed class were built. The Veluwsche Stoomtrein Maatschappij (VSM) owns two Class 23 locomotives: 23 076, which was the first to arrive at the VSM in 1976, and 23 071, which followed in 1978. Both locomotives remain operational to this day.
On order, shipped within 10-15 days
Heavy goods steam locomotive class 44 0104-8 of the Deutsche Reichsbahn. Variant with oil firing High-positioned DR smoke deflectors Smoke chamber door with central lock Middle driving axles with reduced wheel flanges Unobstructed view between the boiler and running gear Pumps at the front Home base Rbd Erfurt, Bw Saalfeld Many of the DR locomotives that remained in the country after the end of the war were converted to oil firing. Until they were gradually replaced by modern diesel and electric locomotives, the Class 44 locomotives formed the backbone of heavy goods services. Due to their enormous tractive power, they were nicknamed 'Jumbos.' The DR retired the last of these "Pachyderms" in 1986.
On order, shipped within 10-15 days
Steam locomotive 001 168 of the Deutsche Bundesbahn. Mould variant! Variant with DB reflex lamps Version used in its final years of service in the early 1970s With closed front skirt Witte smoke deflectors Used for high-quality express train services Tender 2’2’ T 34 Unobstructed view between the boiler and the chassis The two-cylinder locomotives of the Class 01 are regarded as the first express train locomotives to have been built under the standardised construction programme. The DR retained the original design, featuring the large Wagner smoke deflectors and the air and feed pumps in the smoke box recesses, after the Second World War. The DB, by contrast, gradually relocated them to the centre of the locomotive, giving the driver a better view of the track. Almost simultaneously, it replaced the large smoke deflectors with Witte-type ones and modified the majority of the running plates. The first production batches were fitted with leading wheels 800 mm in diameter and were approved for 120 km/h. From locomotive 01 102 onwards, they were fitted with 1,000 mm leading wheels and reinforced brakes, increasing the approved maximum speed to 130 km/h. Until 1939, the locomotives were fitted with riveted tenders of the 2‘2‘ T 32 type. After that, newly delivered locomotives were fitted with welded 2‘2‘ T 34 tenders, whilst those already in service were gradually retrofitted with them.
Pre-order, release expected in Q4 2027
Steam locomotive Class 92.5–10 of the Deutsche Bundesbahn. With Next18 interface Authentic unobstructed view between the boiler and running gear With a maintenance-free bell-shaped armature motor With delicate pipes on the boiler Between 1910 and 1916, a total of 512 T 13 locomotives were built by various manufacturers for the Prussian State Railways. In 1925, the T 13 was reclassified by the Deutsche Reichsbahn as Class 92.5–10, with locomotive numbers 92 501–913 and 92 1001–1072 according to its official numbering scheme. The DB decommissioned the last machine in 1965 at the Kassel railway depot.
On order, shipped within 10-15 days