Road Vehicles
The charger is specifically designed for smaller vehicles such as the Beetle, item 8090 and is optimally matched to the charging current of their batteries. It features the appropriate connector for these vehicle models.
On order, lead time to be confirmed
Functionally equivalent to the programming device for trucks and buses, item 8401, but equipped with a smaller connector designed for passenger vehicles, such as the Beetle, item 8090.
On order, lead time to be confirmed
With this set you can retrofit your long trailers and semitrailers of kibri and other manufacturers to be able to use the full scope of functions of the CarMotion vehicles. Contents: 1 bumper with 5-pole connection plug and infrared transmitter for distance control. Cable length: ca. 19 cm
On order, lead time to be confirmed
High-performance, low-wear motor for underfloor drive with encapsulated gear and one driven axle, suitable for CarMotion vehicles. Operating voltage: 7 – 12 V DC L 2.5 x W 2.8 x H 1.3 cm
On order, lead time to be confirmed
Front axle fully assembled with steering arm and magnet for CarMotion trucks. This front axle is suitable for vehicles with a distance of 45–55 mm from the front axle to the drive axle. Suitable vehicles: 8115, 8152, 8161, 8130, 8131, 8132, 8133, 8135 L 2.2 x W 2.8 x H 1.3 cm
On order, lead time to be confirmed
Lightweight, high-performance, and compact LiPo pouch cells with built-in protection electronics against overcharging, deep discharge, and overcurrent (short-circuit resistant). Replacement part for MB Actros vehicles, designed for operations with the cells connected in parallel. Nominal voltage 3.7 V, capacity each 60 mAh, maximum charge and discharge current 2 C (120 mA). L 22 x W 12 x H 4.5 mm
On order, lead time to be confirmed
Lightweight, high-performance, and compact LiPo pouch cell with built-in protection electronics against overcharging, deep discharge and overcurrent (short-circuit resistant). Replacement parts for MB round bonnet and Magirus square bonnet vehicles. Nominal voltage 3.7 V, capacity 120 mAh, maximum charge and discharge current 2C (240 mA). L 24 x W 12 x H 7.5 mm
On order, lead time to be confirmed
With this set you can retrofit your trailers and short semitrailers of kibri and other manufacturers to be able to use the full scope of functions of the CarMotion vehicles. Contents: 1 bumper with 5-pole connection plug and infrared transmitter for distance control.
On order, lead time to be confirmed
Front axle fully assembled with steering arm and magnet for CarMotion trucks. Suitable vehicles: 8000, 8001, 8002, 8003, 8010, 8011, 8012, 8013, 8014, 8015, 8016, 8017, 8018, 8019, 8020, 8021, 8022, 8023, 8030, 8031, 8032, 8033, 8034, 8035, 8036, 8040, 8041, 8050, 8051, 8052, 8053, 8054, 8055, 8060, 8061, 8065, 8070, 8071, 8072, 8114, 8155, 8160 L 2.2 x W 2.8 x H 1.3 cm
On order, lead time to be confirmed
These steered axles for semitrailers are excellently suited for driving smaller radii even with longer semitrailers, without having to widen the roads very much in the curves or the semitrailers getting too far into the lane of opposite traffic. Precisely guided by ball bearing mounted cogwheel mechanism.
On order, lead time to be confirmed
High-performance, low-wear motor for underfloor drive with encapsulated gear and one driven axle, suitable for CarMotion vehicles. The rear axle is non-driven and height-adjustable. Operating voltage: 7 – 12 V DC L 4 x W 2.8 x H 1.3 cm
On order, lead time to be confirmed
The universal electronics module for trucks offers compact solutions for retrofitting trucks over 7.5 tons with the proven driving characteristics of CarMotion trucks. The slim module (W 12.5 mm x L 26.5 mm) is particularly suited for tight installation spaces and operates in conjunction with the H0 gearbox with motor, item 8426. Power is supplied by two 60 mAh rechargeable batteries included in the set. This module is designed exclusively for use with this specific motor and battery configuration. An additional trim-to-size distribution board (approx.. W 7 mm x L 25 mm) can be shortened to L 17 mm and facilitates the connection of LEDs for lighting purposes and enables extra lighting effects. An expansion interface is provided for additional modules. The LEDs and sensors come pre-wired with enamelled wires, making installation straightforward. Expansion kits for further lighting effects will be available in the future. Set includes: Main board, distribution board, Hall sensor, charging and programming socket, 2 rechargeable batteries, rear bumper with lights and IR transmitter, mini board with IR receiver, mini board with reed switch and driver’s cab lighting, mini board with trailer connector
On order, lead time to be confirmed
For the proper installation of the magnetic tape, items 8429 and 8430 in freely designed road courses to avoid collision with oncoming traffic. Milling of the groove for the magnetic tape is done along the marking.
On order, lead time to be confirmed
For the proper installation of the magnetic tape, items 8429 and 8430 in freely designed road courses to avoid collision with oncoming traffic. Milling of the groove for the magnetic tape is done along the marking.
On order, lead time to be confirmed
Marking aid for marking the locations of the permanent magnets, item 8431 at the correct spacing relative to each other, in a magnetic sequence, and with respect to magnetic tape, items 8429/8430. L 7 x W 3 x H 0.4 cm
On order, lead time to be confirmed
Cable for extending the EasyChain line for the InduktivCharger, item 8408. Ideally suited for lengthening the EasyChain line and connecting remote InduktivChargers. Length: 0.5 m per cable
On order, lead time to be confirmed
The permanent magnet holder is the ideal solution for testing the CarMotion system. Equipped with one or more magnets, the holder can be flexibly positioned to the right of the roadway. This allows you to precisely verify whether – and at which point – the CarMotion vehicle detects and executes defined control commands. Its sturdy design enables quick setup and easy repositioning during test runs, ensuring accurate results under realistic conditions.
On order, lead time to be confirmed
With this set you can retrofit your kibri trailers or semitrailers to optimize the running smoothness and the tracking accuracy of the vehicle. This will improve the driving characteristics of the trailer resp. the semitrailer. Contents: 6 rubber wheels, 6 rims, 3 steel axles, 6 sockets. Suitable for trailer and semitrailer with up to 3 axles and single tyres.
On order, lead time to be confirmed
With this set you can retrofit your kibri trailers or semitrailers to optimize the running smoothness and the tracking accuracy of the vehicle. This will improve the driving characteristics of the trailer resp. the semitrailer. Contents: 8 rubber wheels, 4 rims, 2 steel axles, 4 sockets. Suitable for 2-axle trailer and semitrailer with twin tyres.
On order, lead time to be confirmed
The car detector recognizes the steering magnet of passing vehicles and is installed beneath the magnetic tape or conductive wire. Exclusively designed for use with the IR module item 8403, the InduktivCharger (item 8408) and the speed cameras (items 1330, 1331 and 1332).
On order, lead time to be confirmed
The IR transmitting diodes are designed as a replacement component for the IR Mini, item 8403 and IR Scanner, item 8406. They come equipped with pre-wired connection leads (without pre-resistors). Cable length to the IR LEDs: approx. 300 mm Dimensions IR LEDs: approx. L 1.6 x W 0.8 x H 0.8 mm
On order, lead time to be confirmed
The IR transmitting diodes are designed as a replacement component for the IR Mini, item 8403 and IR Scanner, item 8406. They come equipped with pre-wired connection leads (without pre-resistors). Cable length to the IR LEDs: approx. 300 mm Dimensions IR LEDs: approx. L 1.6 x W 0.8 x H 0.8 mm
On order, lead time to be confirmed
This cable is designed for extending the 6-pin connector of the programming device, item 8401, or the charger, item 8400. Ideal for wiring hard-toreach modules, such as the IR Mini, item 8403.
On order, lead time to be confirmed
The universal electronics for buses offer compact solutions for retrofitting coach and transit buses with the proven driving characteristics of CarMotion trucks. The slim module (W 12.5 mm x L 26.5 mm) is particularly suited for tight installation spaces and operates in conjunction with the H0 gearbox and motor, item 8426. Power is supplied by one 120 mAh rechargeable battery included in the set. This module is designed exclusively for use with this specific motor and battery configuration. An additional trim-to-size distribution board (approx.. W 7 mm x L 25 mm) can be shortened to L 17 mm and facilitates the connection of LEDs for lighting purposes and enables extra lighting effects. An expansion interface is provided for additional modules. The LEDs and the sensors come pre-wired with enamelled wires, making installation straightforward. Expansion kits for further lighting effects will be available in the future. Set includes: Main board, distribution board, Hall sensor, charging and programming socket, rechargeable battery, mini board with IR transmitter, mini board with IR receiver, mini board with reed switch and driver’s cab lighting, 4 mini boards for interior bus lighting, mini board with trailer connector.
On order, lead time to be confirmed