Track Accessories
For H0 signals 6200/6201/6205/6206 to clip onto the model tracks
On order, shipped within 10-15 days
Electrically operated turntable for 3-rail AC system, with turntable control switch 6909. The turntable is prototypically mounted in a recess and fitted with accurate details. As delivered, there are 6 exit tracks and 4 over-run ends. The exit tracks can be unclipped and repositioned at an angle of 7,5° as desired, or extended using the turntable extension set 665301 right up to the complete 48 exits. Installation dimensions: Required installation opening: 340 mm. Installation depth measured from table top edge: 30 mm. External diameter of the turntable with track connections: 465 mm. Turntable bridge length: 310 mm. Note: Control your turntables easily – with TURN-CONTROL, the electronic turntable control device (item No. 6915).
On order, shipped within 10-15 days
Extension set for the AC turntable 665201 for 3-rail AC operation with nickel silver tracks. The set contains 3 exit tracks and 3 over-run ends.
On order, shipped within 10-15 days
Sliding wall wagon “FLEISCHMANN Clean” for cleaning the tracks of the German Federal Railway. Simply integrate into a normal train Your rails will always be kept perfectly clean Track cleaning wagon with real cleaning effect. Dust, rubber abrasion and oil etc. are reliably removed. The rail surface is not attacked during this process, meaning that new dirt will not settle again quickly.
On order, lead time to be confirmed
Turntable controller with track pre-selection TURN-CONTROL is suitable for analogue and digital control of the turntables art. no. 6152, 6154, 665201, 9152 and 35900. An LCD display gives a visual indication of the setting of the turntable bridge, the location of the track exits installed and shows the active track exit, together with additional functions. Symbols of the active functions give it a simple, user-friendly operation. Each track exit can be individually controlled. Because the polarity change is catered for by the switch, when rotating through 360°, the turntable is protected against short circuit. The turntable control switch is suitable for operation wtih 2-rail DC operation, the 3-rail AC operation, and will also operate with all digital systems - DCC, FMZ and Märklin-Digital (contains a turntable decoder). No changes or alterations to the turntable are necessary. Content: - TURN-CONTROL 6915 Controller - Connection cable 396865 (for power feed) - 7-pole connecting plug - Operating manual Märklin is a registered trademark of the company of Gebr. Märklin & Cie. GmbH, Göppingen.
On order, shipped within 10-15 days
Model Turntable, electrically driven, with individual electrically switchable track exits, with turntable switch 6910. Length of the turning bridge 183 mm. The Model: The turntable is sunk into the ground, exactly like the real thing and is complete with all the correct detailling. The basic turntable has 6 exit tracks and 4 stub tracks. The track exits are set at 7,5° intervals, but can be altered if desired, or extended with the extension set 9153 up to total of 48 track exits. The "thinking" turntable: The turntable movement is controlled by using the switch 6910, in order to reach the desired track exit. The track power feed is via the turntable bridge. Now the switch 6910 will enable the desired track exit, which is lined up with the turntable, to be electrically switched on. All the other track exits (even one directly opposite) will remain without power. In this way, each of the maximum of 48 track exits can be individually controlled and electrically switched on, without the need for any additional wiring. Note: Control your turntables easily – with TURN-CONTROL, the electronic turntable control device (item No. 6915).
On order, shipped within 10-15 days
Turntable extension set for turntable 9152 containing 3 exit tracks and 3 over-run ends.
On order, shipped within 10-15 days
With warning crosses and re-railing section. Length 55.5 mm.
On order, shipped within 10-15 days
Fishplates, 20 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Insulated fishplates, 20 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Rocker for fixing bridges and viaducts (20 pieces). By Kato, N gauge.
On order, shipped within 4-5 days
Kit. Modern rail cranes are used all over the world, most of the time in the construction and maintenance of the local railway tracks, but often also in case of accidents. In far-off countries, these cranes belonging to the rail maintenance cars are generally transported by sea. Due to their high total weight in service order of over 100 t they are usually transported divided in upper and lower part to the port and are reassembled only at the point of destination. This vehicle transports the superstructure of a rail crane. The undercarriage is transported by item 13601. With high quality pad printing. L 26.0 x W 3.5 x H 4.5 cm Level of difficulty: 2 (advanced)
On order, lead time to be confirmed
Kit. This vehicle transports the undercarriage of a rail crane. The superstructure is transported by item 13600. With high quality pad printing. L 25.7 x W 3.3 x H 4.0 cm Level of difficulty: 2 (advanced)
On order, lead time to be confirmed
Functional kit. With pre-assembled front and rear lighting and yellow flashing light. Used for mending and maintenance work on catenary wire systems. With high quality pad printing. L 7.5 x W 3.3 – 5.0 x H 4.2 cm / Crane boom fully tilted 8.8 cm Level of difficulty: 2 (advanced)
On order, lead time to be confirmed
Kit. Level of difficulty: 1 (beginners)
On order, lead time to be confirmed
Wheel scotches are used to secure wagons on gradients and sidings against rolling away unintentionally. The pack contains 12 pieces.
Content: 12 pc. (CHF 0.78 / 1 pc.)
On order, shipped within 10-15 days
Bridges can be found on every railway. On a model railway they make attractive eye-catchers. This prototypical model of a through girder bridge features imitation rivets and a plank walkway for pedestrians. For use with straight LGB tracks.
On order, shipped within 10-15 days
Is your model railway supposed to cross a large gorge? Or do you want to build an interesting eye-catcher into your layout? This impressive model, 1,200 mm long and 300 mm high, is available for just that. The clearance height is 224 mm. The kit consists of seven parts that can be assembled in a few minutes. You only need a screwdriver. Two abutments are included, which makes installation easier on all LGB layouts. For use with the LGB bridge blocks (LGB 50611-50614). Prepared for use with the LGB 56402 standard catenary.
On order, shipped within 10-15 days
Model With these adapters you can use the LGB bridge blocks with the arched bridge (LGB 50610). Install two bridge blocks side by side under each bridge mount. Width: 200 mm, height: 15 mm (without pins). Note for use with the L50610 arched bridge
On order, shipped within 10-15 days
Model Let your LGB run at an elevated level! For use with LGB 50611 or LGB 50614. Width: 100 mm, height: 15 mm (without pins). Note for use with the L50610 arched bridge
On order, shipped within 10-15 days
Model If your LGB wants to go up high... For use with LGB 50611 or LGB 50614. Width: 100 mm, height: 45 mm (without pins). Note for use with the L50610 arched bridge
On order, shipped within 10-15 days
With these adapters you can mount your LGB tracks on the bridge blocks. Width: 100 mm.
On order, shipped within 10-15 days
The level crossing barrier can easily be installed in any straight LGB track. The weight of the approaching train closes the barrier arms. The barrier opens when the last wagon has passed the level crossing.
On order, shipped within 10-15 days
These sturdy brass wires are used with the "Standard" and "Modell" catenary systems. The wires have a grooved profile. Length: 680 mm. Can be shortened as required.
On order, shipped within 10-15 days