Track Accessories
A reproduction of a modern catenary mast of the Swiss railways. On this model the catenary wire is suspended from a supporting cable. The prototypical mast is made of aluminium and is equipped with two booms, one for the catenary wire and one for the supporting cable. The catenary wire is mounted 225 mm above the top of the rails. The catenary mast base (LGB 56302) or the pivoting catenary mast base (LGB 56303) can be used to set up the mast.
On order, shipped within 10-15 days
This catenary mast base allows you to connect the catenary mast (LGB 56301) and the standard catenary mast (LGB 56405) securely to your LGB tracks. On the catenary mast base there is an adjustable bar (5.5-30 mm) for mounting on the tracks. The catenary masts are inserted into the catenary mast.
On order, shipped within 10-15 days
Similar in design to the catenary mast base (LGB 56302), this one can also pivot. It allows you to set up catenary masts on lines with gradients of up to 25%. Recommended for steep lines and rack railways.
On order, shipped within 10-15 days
Catenary cross-span assemblies are ideal for use wherever several tracks lie next to each other and are to be spanned with catenary wire. A maximum of 5 tracks can be spanned with the catenary cross-span assembly. Length: 1,000 mm, can be shortened as required.
On order, shipped within 10-15 days
This additional boom allows you to use the standard catenary mast (LGB 56405) on double-track lines.
On order, shipped within 10-15 days
The LGB "Standard" catenary is a reproduction of a simple catenary system such as those found on tramways and branch lines. It is particularly suitable for level layouts and is easy to assemble. The mast has a boom to which the catenary wire (LGB 56201) is attached above a single-track line. The catenary mast base (LGB 56302) or the pivoting catenary mast base (LGB 56303) can be used to set up the mast. Height 305 mm.
On order, shipped within 10-15 days
In addition to securing the Gauge 1 tracks against unintentional loosening of the track connection, this retaining clip also improves the electrical contact. Bag of 30 pieces.
Content: 30 pc. (CHF 0.73 / 1 pc.)
On order, shipped within 10-15 days
Twin-coil drive with feedback contacts. End position cutoff and locking. For screwing onto the 5965, 5966, 5976 and 5977 points. Operated by remote control with the 7272/72720 or 7271/72710 control panel (conventional operation) or with the 6083/60830 k 83 decoder (digital operation). 3 connecting cables are included. Size 67 x 41 x 17 mm.
On order, shipped within 10-15 days
Point motor with motor cut-off at the end of travel in both directions. Two changeover switches rated at 3 A, possible uses: common crossing polarisation, feedback, route control, signal control, level crossing gate control. Throw: 1.0-10.0 mm. Size 48 x 27.7 x 13 mm. (H1019-1).
Pre-order, release expected in December 2026
Point stand with signal lantern for a right-hand point, illuminated, without changeover switch. (H1035-1).
On order, shipped within 10-15 days
Point stand with signal lantern for a left-hand point, illuminated, without changeover switch. (H1055-1).
On order, shipped within 10-15 days
Model Made of welded steel wire. Length 360 mm. Standard length. Intended for straight track. Pack of 5 pieces. Note The catenary wires for the H0 catenary are made of welded steel wire. The electroplated surface looks realistic and protects against corrosion. The catenary wire pieces are prefabricated and very easy to install.
Content: 5 pc. (CHF 4.18 / 1 pc.)
On order, shipped within 10-15 days
Can be used on its own as well as with the 7263 arched bridge. For taking plastic or metal track. 3 clips for fastening the K tracks and instructions for building the bridge. Height 45 mm. Length 180 mm.
On order, shipped within 10-15 days
For taking plastic or metal track. 6 clips for fastening the K tracks and instructions for building the bridge. Arch height 117 mm. Length 360 mm.
On order, shipped within 10-15 days
Model Traverser in a new realistic colour scheme. Base plate with 2 approach tracks and 8 sidings. Track connections for Märklin metal track. With the appropriate transition tracks it can of course also be used for C track and plastic track. The deck has a motor drive in the machinery house for forward and reverse running. Control unit and connecting cable for remote control. The deck stops automatically at the track connections. Track power for the sidings is supplied by way of the platform. Additional connections for the catenary. Size of the base 360 x 420 mm. Deck length 288 mm. Note The traverser can alternatively be controlled by an m 84 decoder by way of Märklin Digital. The connection of the traverser is described in the instructions for the m 84 decoder.
On order, shipped within 10-15 days
Replacement base for line masts. Can be cut to length to suit all common H0 track systems with or without a ballast bed. With a matching screw for mounting. Pack of 20 pieces.
Content: 20 pc. (CHF 0.70 / 1 pc.)
On order, shipped within 10-15 days
Length 180 mm. Width 64 mm. For holding straight C tracks. 2 ramp sections correspond to the 24188 + 24172 tracks.
On order, shipped within 10-15 days
Model Single-track level crossing with half barriers, fully pre-assembled. For direct connection to C tracks. 2 electromagnetically operated barriers, each with 2 red warning lamps that light up when the barrier is closed. Ready for connection, easy to install. Contact track set: 3 straight tracks, each 94.2 mm. Size of each base 137 x 95 mm. Highlights The level crossing is fully assembled and contains 2 contact tracks You only have to plug in your tracks and off you go
On order, shipped within 10-15 days
Improved version of the 7549 point motor. Suitable for the 2265 and 2266 points (new version), 22715 and 22716, of the 2275 double slip point as well as for the KOMBI extension programme. Automatic cut-off at the end of travel. Automatic feedback possible with the 72710 control panel. Below-baseboard mounting with the 7548 fitting kit.
On order, shipped within 10-15 days
Model Contains all the parts for assembling the S+E catenary. Contents: 19 masts for the catenary, 20 contact wire sections, 8 isolating sections, 6 connecting springs and assembly instructions. Note The SET assembly programme is a system with a continuation, with which you can extend the track sections of the starter sets step by step. After starting with the 81530/81535 or 81562 starter set, you extend it with the E 8190 or E 8191 pack. You can then systematically expand your layout in any order with the T1 8192, T2 8193 and T3 8194 track packs. If you start with the 81781/81785 or 81852 starter sets, you already have the E 8191 extension pack integrated and further expansion can then again be carried out without any problem with the T1 8192, T2 8193 and T3 8194 track packs. The 8198 catenary pack for S+E and the 8199 catenary pack for T1+T2+T3 make it easier within the SET programme to get started with fully functional catenary operation, with which two trains can be controlled independently of each other on one line.
On order, shipped within 10-15 days
Model Addition to 8198 for T1 to T3. Contents: 4 masts for the catenary, 16 tower masts, 30 contact wire sections, 8 cross connections, 30 contact wire insulators, 8 isolating sections, 6 connecting springs, 5 contact wire clamps and assembly instructions. Note The SET assembly programme is a system with a continuation, with which you can extend the track sections of the starter sets step by step. After starting with the 81530/81535 or 81562 starter set, you extend it with the E 8190 or E 8191 pack. You can then systematically expand your layout in any order with the T1 8192, T2 8193 and T3 8194 track packs. If you start with the 81781/81785 or 81852 starter sets, you already have the E 8191 extension pack integrated and further expansion can then again be carried out without any problem with the T1 8192, T2 8193 and T3 8194 track packs. The 8198 catenary pack for S+E and the 8199 catenary pack for T1+T2+T3 make it easier within the SET programme to get started with fully functional catenary operation, with which two trains can be controlled independently of each other on one line.
On order, shipped within 10-15 days
Prototype Special buffer stop for shifted loads, of the kind found on railway tracks for many decades and even, in isolated cases, still today. Model Delicately laser-cut kit for a buffer stop for shifted loads, for Märklin Z track. Precisely fitting model made of hard architectural card with a reproduction of the gusset plates. A small but fine detail for layout building, with prototypically implemented dimensions. 2 kits are included in the contents supplied. To be glued with commercially available wood glue, among other things (Bindan, Ponal etc.). Dimensions per buffer stop: L x W x H approx. 17 mm x 16 mm x 20 mm. Highlights Suitable for many eras (II-VI) Delicate model An important detail
On order, shipped within 10-15 days
Basic element with a mounting plate. Height 38 mm.
On order, shipped within 10-15 days
For the power feed. With a mounting plate and a connecting cable. Height 38 mm.
On order, shipped within 10-15 days