Track System
Variation Set V17, double-track oval, slab track. By Kato, N gauge.
On order, shipped within 4-5 days
CV-1 track oval R 150, 13 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
CV-2 electric points set R 150, 6 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Flexible track 808 mm, wooden sleepers, without ballast bed. By Kato, N gauge.
On order, shipped within 4-5 days
Flexible track 808 mm, concrete sleepers, without ballast bed. By Kato, N gauge.
On order, shipped within 4-5 days
Pier set for up and down ramp, 12 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Pier extension set for up and down ramp, 12 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
Piers 50 mm, 5 pieces. By Kato, N gauge.
On order, shipped within 4-5 days
H0 HV21 Variation Set, signal set, 9 pieces. By Kato, H0 gauge.
On order, shipped within 4-5 days
G1 straight track, length 444.12 mm
On order, lead time to be confirmed
Compensating section. Together with the curved track R10 (45025), the opposing curve can be built for the simple points and the double crossover.
On order, lead time to be confirmed
Flexible track section for any radii. Supplied without fishplates.
On order, lead time to be confirmed
Standard curve R1. The angle is 22.5°, the radius is 914.4 mm. 16 track pieces are required to form a circle.
On order, lead time to be confirmed
Parallel curve R2. The angle is 22.5°, the radius is 1028.7 mm. This results in a track spacing to R1 of 114.3 mm. A circle requires 16 track pieces.
On order, lead time to be confirmed
Parallel curve R2. The angle is 7.5°, the radius is 1028.7mm. 2 pieces complete the 45° curve when using the curved point.
On order, lead time to be confirmed
Curved track for points and DKW. The angle is 11.25°, the radius is 1649.39 mm. 32 track pieces are required to form a circle.
On order, lead time to be confirmed
Point angle 11.25°, length 455.39 mm, radius 1649.39 mm (R10). Supplied with a point lever, it can be upgraded to a digitally controllable point using the 45040 point motor.
On order, lead time to be confirmed
Point angle 11.25°, length 455.39 mm, radius 1649.39 mm (R10). Supplied with a point lever, it can be upgraded to a digitally controllable point using the 45040 point motor.
On order, lead time to be confirmed
Point angle 11.25°. Radius of the inner curve 1028.70 mm. The outer curve is a curve with a continuously changing radius. It begins at the point blade with 1786.89 mm and ends with 1540.00 mm. Supplied with a point lever, it can be supplemented with the 45040 drive to become a digitally controllable point.
On order, lead time to be confirmed
Point angle 11.25°. Radius of the inner curve 1028.70 mm. The outer curve is a curve with a continuously changing radius. It begins at the point blade with 1786.89 mm and ends with 1540.00 mm. Supplied with a point lever, it can be supplemented with the 45040 drive to become a digitally controllable point.
On order, lead time to be confirmed
Double turnout (three-way point) 11.25°, with point lever, length 586 mm, radius 1649.39 mm (R10). Supplied with point lever, can be upgraded to a digitally controllable point using two 45040 point motors.
On order, lead time to be confirmed
The point motor can be controlled digitally or analogously. The motor can be mounted on points using the control lever 49035. Dimensions 46 x 33 x 8 mm (without lantern)
On order, lead time to be confirmed
This Spur 0 uncoupler can be installed anywhere in existing straight Lenz track, even afterwards. Contact springs ensure the necessary electrical connection to the track. A DCC decoder is already fitted, and operation is via the point address.
On order, lead time to be confirmed
The turntable has a total of 32 exits, of which 31 can be used for track connections. The exits are at an angle of 11.25° to each other. The outside diameter is 586 mm, which is the length of a double-crossing point (DKW) of the track system. Length of the turntable 500 mm
On order, lead time to be confirmed