Accessories
The DAISY II digital starter set is a digital entry-level system for the ambitious model railway enthusiast. It consists of a DAISY II hand controller and a DCC Central Station, which are connected to each other via a LocoNet cable. It supports all the functions desirable for comfortable model railway operation.
On order, lead time to be confirmed
Future-proof! The radio system can be expanded via software. With the expansions, it is possible to control vehicles with corresponding radio receivers directly in DCC format via the radio master. The DCC command no longer needs to be transmitted to the locomotive via the track. This allows, for example, the locomotives of the garden railway or the vehicles of the Faller Car System to be controlled directly.
On order, lead time to be confirmed
Extension of the system software for the Intellibox and Intellibox IR Upgrade 2.0 is an extension for all Intelliboxes with article numbers 650, 65 000 and 65 050 that were delivered with a system software version lower than 2.0. It provides the following new functions: 10 000 special locomotive functions With suitable DCC decoders, the special functions f0–f9 999 can be accessed. Locomotive selection from the refresh cycle The refresh cycle contains all locomotive addresses that are currently being supplied with digital information by the Intellibox. The new software provides a selection list of these addresses from which the desired locomotive can be selected directly. Lokfind function As soon as a locomotive with a DCC decoder is placed on the programming track, the decoder's locomotive address is automatically transferred to a speed controller. Reloading the locomotive addresses The locomotive addresses shown on the Intellibox display are, if desired, saved when the operating voltage is switched off and are immediately available again for the next running session without annoying re-entry. Halt mode The Intellibox can be put into halt mode using the STOP and GO buttons. All locomotives are stopped by emergency stop, while the track voltage is maintained. Points and signals can still be changed. Using the Intellibox as an IB-Control The Intellibox can be set via the device configuration so that it behaves like an IB-Control. This makes it possible to use two Intelliboxes together on one layout. Route control On all devices without route control, the system software is additionally extended with the ability to switch up to 48 routes. mfx special functions mfx locomotives are controlled via the Intellibox using the Motorola data format. If a locomotive has more than four special functions, the special functions f5–f8 are automatically controlled via the following decoder address. The upgrade software is available free of charge on the Internet for owners of the Intellibox IR. For older devices the software can be purchased. Art. no.: 65020 Upgrade Software 2.0
On order, lead time to be confirmed
Suitable devices for the RailCom extension 65030 Intellibox I art. no. 650 and 65000 Intellibox IR art. no. 65050 Intellibox Basic art. no. 65060 IB-COM art. no. 65070 and 65071 Power 3 art. no. 656 and 65600 Power 6 art. no. 65650 Fleischmann Twin-Center art. no. 6802 Fleischmann Twin-Booster art. no. 6807 Piko Power Box art. no. 55015 The RailCom extension 65030 is a circuit board (not illustrated) that is retrofitted to the digital command stations listed above. It ensures that the cutout required for RailCom operation is also transmitted. Installation is only possible at our factory. The device must therefore be sent to us for modification. Attention: for installation, the digital command station must be sent to us. Postage costs for returning the modified command station to you are charged in addition. Art. no. 65030 RailCom extension
On order, lead time to be confirmed
The DAISY II Central Station is a compact LocoNet DCC central station for the model railway enthusiast. It is now available in a new, improved version with higher output power and compatibility with the ABC braking system.
On order, lead time to be confirmed
Intellibox 3 Proven features combined with innovative technology In appearance, the large, high-resolution colour display with touch function stands out. With the new operating options we have strictly continued and simplified the operating concept. Anyone who knows the Intellibox II will immediately feel at home with the Intellibox 3. It goes without saying that you can continue to use our previous devices in conjunction with the Intellibox 3. The speed display of the vehicles can be shown in speed steps, as a percentage of top speed and also in km/h. Up to 32 768 special functions per locomotive address can be switched. In combination with LISSY or MARCo, you can have the position of your train on the layout displayed. Another highlight is decoder programming in plain text. For programming the standard CVs in DCC format, the annoying search for the locomotive decoders' operating instructions is therefore no longer necessary. The bit calculation aid simplifies the programming of special CVs. The detailed help function, a model time clock and a booster mode complete the Intellibox 3's range of features. As ever: everything in one box With the Intellibox 3 you are completely equipped for digital operation. The Intellibox 3 can be operated on 2-rail and 3-rail layouts. From gauge Z, via N, TT and H0, right up to the large gauges 0, 1 and IIm(G), the Intellibox 3 is the right command station. It supports up to 128 speed steps and 9 999 decoder addresses. Locomotive and function decoders in DCC, mfx®, Motorola or Selectrix® format. Point and switching decoders in Motorola or DCC format from different manufacturers can be used at the same time. A single device provides you with the following components of a digital system: central unit, booster, two speed controllers, keyboard, programmer, interface, feedback monitor, route control, model time clock, RailCom® receiver, computer connection via USB or WLAN and the LISSY/MARCo mode with the DirectDrive function. The integrated infrared receiver allows direct use of the existing IRIS infrared remote control. Art. no. 65300 Intellibox 3
On order, lead time to be confirmed
Is your command station too far from the shunting yard? Would you like to have more locomotives permanently at hand? Do you need more routes? You need the IB-Control 3 Fine prospects The new IB-Control 3, as an additional control unit, turns any LocoNet command station into a modern control system with all the operating convenience possible today. It extends any command station with two further speed controllers with locomotive selection via locomotive names stored in a database, a control panel with symbols for points and signals, as well as monitoring options for feedback detectors and LISSY/MARCo receivers and a model time clock. Each IB-Control 3 extends the digital control by 128 routes with 40 entries each, which can be called up at the press of a button or triggered by feedback from the train. The routes can be interlocked with one another. With the large, high-resolution colour display with touch function and a backlit keyboard in night design, model railway fun with the new IB-Control 3 for all LocoNet command stations is only now really getting started. Art. no. 65430 IB-Control 3
On order, lead time to be confirmed
The DAISY II radio hand controller is suitable for operation with all central units featuring a LocoNet connection. It can be plugged directly into the LocoNet to operate via a wired connection, or wirelessly with a radio master which is connected to the central unit via LocoNet. The range of the DAISY II radio hand controller is up to 100 m (open field) to the nearest radio master.
On order, lead time to be confirmed
Radio module for DAISY II. This module allows the DAISY II handheld controller 66300 to be upgraded to a radio handheld controller. The Funk-Master is additionally required for radio operation. Installation is described in the manual of the DAISY II handheld controller. With charging adapter.
On order, lead time to be confirmed
Plexiglas mounting bracket for screwing to the edge of the layout. With cable holder.
On order, lead time to be confirmed
The Funk-Master is the system's radio control centre. All radio operations are coordinated and executed within it.
On order, lead time to be confirmed
Free address setting without decoder restrictions Points and signals with a solenoid drive that are to be controlled digitally must be fitted with a solenoid accessory decoder. Lamps, colour light signals or track sections that are to be switched on and off digitally are digitised with a switching decoder. Uhlenbrock solenoid accessory and switching decoders can be used in Märklin, Motorola and DCC digital systems. In Motorola operation, addresses 1–320 can be addressed with the Intellibox, and addresses 1–256 with other command stations. In DCC operation, addresses 1–2048 are possible. The addresses are not preset. They can be chosen freely and independently of one another. Each module has two outputs. Depending on the type, both outputs can be addressed together under one address or independently of each other under two addresses. The relay contacts of the switching decoders have potential-free outputs and can be connected as desired. Each output can be loaded with 1 A. By limiting the connections to two per module, the cable runs remain short and the wiring of the layout stays easy to follow. Connection is conveniently made via screw terminals. Setting the address is extremely simple. First the programming button of the decoder is pressed, then the corresponding point button on the control panel. The decoder simply remembers the corresponding address. The decoders are supplied with operating voltage and control information from the digital command station. Switches by pulse (+20 V) via two addresses, independently of each other, two solenoid accessories with one drive (point, signal) or one solenoid accessory with two drives (three-way point, double slip, signal with distant signal). The module is short-circuit protected. Art. no. 67200 MD2 solenoid accessory decoder
On order, lead time to be confirmed
You can now use LISSY on your digital layout to do everything that was previously only possible with a computer. Without a computer, LISSY makes simple automatic control functions possible, such as block operation and shuttle lines, as well as optimised automatic control of even extensive fiddle yards. LISSY is identical in construction to the Fleischmann Train Navigation and offers interesting additional functions. With LISSY, data are transmitted from the locomotive to the digital system by infrared light. For this, an infrared transmitter is mounted on the vehicle. The infrared sensors of the receiver module are built into the track. LISSY recognises the train and shows which train has entered track 1 of the station. LISSY controls shuttle train operation in the terminus of the single-track branch line. LISSY manages your fiddle yard with through track, independently finds an individual track for each train and, when needed, automatically lets the trains run out of the fiddle yard again. The through track can be used on a locomotive-specific basis or, at the push of a button, by all locomotives. LISSY is a block system for digital layouts and automatically controls the block posts on the layout, without using a computer. LISSY slowly brakes every digital locomotive in front of a red signal using the decoder's internal braking delay. LISSY switches the sound of locomotives depending on the situation, for example the whistle before the tunnel or the horn at the level crossing before the whistle board. LISSY fades out the sound of locomotives fitted with "IntelliSound" when they travel into hidden areas (fiddle yard, tunnel). LISSY switches the lights of a selected locomotive on or off after a certain time, e.g. when the driver has stabled the locomotive. LISSY controls the speed of locomotives, e.g. at station approaches or on slow-speed sections. LISSY measures the speed of passing locomotives to scale. LISSY works without any break in the track and can therefore easily be retrofitted to any model railway layout. Information is displayed on the Intellibox or Track-Control display or on a connected PC. Art. no. 68000 LISSY set: 2 transmitters, 1 receiver, LocoNet cable, manual
On order, lead time to be confirmed
You can now use LISSY on your digital layout to do everything that was previously only possible with a computer. Without a computer, LISSY makes simple automatic control functions possible, such as block operation and shuttle lines, as well as optimised automatic control of even extensive fiddle yards. LISSY is identical in construction to the Fleischmann Train Navigation and offers interesting additional functions. With LISSY, data are transmitted from the locomotive to the digital system by infrared light. For this, an infrared transmitter is mounted on the vehicle. The infrared sensors of the receiver module are built into the track. LISSY recognises the train and shows which train has entered track 1 of the station. LISSY controls shuttle train operation in the terminus of the single-track branch line. LISSY manages your fiddle yard with through track, independently finds an individual track for each train and, when needed, automatically lets the trains run out of the fiddle yard again. The through track can be used on a locomotive-specific basis or, at the push of a button, by all locomotives. LISSY is a block system for digital layouts and automatically controls the block posts on the layout, without using a computer. LISSY slowly brakes every digital locomotive in front of a red signal using the decoder's internal braking delay. LISSY switches the sound of locomotives depending on the situation, for example the whistle before the tunnel or the horn at the level crossing before the whistle board. LISSY fades out the sound of locomotives fitted with "IntelliSound" when they travel into hidden areas (fiddle yard, tunnel). LISSY switches the lights of a selected locomotive on or off after a certain time, e.g. when the driver has stabled the locomotive. LISSY controls the speed of locomotives, e.g. at station approaches or on slow-speed sections. LISSY measures the speed of passing locomotives to scale. LISSY works without any break in the track and can therefore easily be retrofitted to any model railway layout. Information is displayed on the Intellibox or Track-Control display or on a connected PC. With the shuttle train control, the LISSY receivers are pre-configured for a single-track shuttle line, so that the line can be put into operation directly after installation, without any programming effort. The shuttle train control receivers can, like all other receivers, be reprogrammed for other functions. For single-track shuttle lines Pre-configured LISSY receivers for all terminal stops Incl. LISSY transmitter Can be used with Intellibox, Twin-Center and Piko Power-Box Art. no. 68010 LISSY shuttle train control: 1 LISSY transmitter, 2 LISSY receivers, 2 LocoNet cables 2.15 m, the LISSY manual and special instructions for installing and commissioning the shuttle line.
On order, lead time to be confirmed
You can now use LISSY on your digital layout to do everything that was previously only possible with a computer. Without a computer, LISSY makes simple automatic control functions possible, such as block operation and shuttle lines, as well as optimised automatic control of even extensive fiddle yards. LISSY is identical in construction to the Fleischmann Train Navigation and offers interesting additional functions. With LISSY, data are transmitted from the locomotive to the digital system by infrared light. For this, an infrared transmitter is mounted on the vehicle. The infrared sensors of the receiver module are built into the track. LISSY recognises the train and shows which train has entered track 1 of the station. LISSY controls shuttle train operation in the terminus of the single-track branch line. LISSY manages your fiddle yard with through track, independently finds an individual track for each train and, when needed, automatically lets the trains run out of the fiddle yard again. The through track can be used on a locomotive-specific basis or, at the push of a button, by all locomotives. LISSY is a block system for digital layouts and automatically controls the block posts on the layout, without using a computer. LISSY slowly brakes every digital locomotive in front of a red signal using the decoder's internal braking delay. LISSY switches the sound of locomotives depending on the situation, for example the whistle before the tunnel or the horn at the level crossing before the whistle board. LISSY fades out the sound of locomotives fitted with "IntelliSound" when they travel into hidden areas (fiddle yard, tunnel). LISSY switches the lights of a selected locomotive on or off after a certain time, e.g. when the driver has stabled the locomotive. LISSY controls the speed of locomotives, e.g. at station approaches or on slow-speed sections. LISSY measures the speed of passing locomotives to scale. LISSY works without any break in the track and can therefore easily be retrofitted to any model railway layout. Information is displayed on the Intellibox or Track-Control display or on a connected PC. With this station control, the LISSY receivers are pre-configured for a 3-track station with through track, so that the station can be put into operation directly after the receivers are installed, without any programming effort. Two receivers take over the tasks of entry and exit manager, three receivers monitor the various tracks. The receivers can be reprogrammed only for use as station control, e.g. as a station extension for five additional tracks. For stations with digitised points Pre-configured LISSY receivers for a 3-track station with through track or as a station extension for 5 additional tracks Incl. LISSY transmitters for 5 vehicles Can be used with Intellibox, Twin-Center and Piko Power-Box Art. no. 68020 LISSY station control: 5 LISSY receivers, 5 LISSY transmitters, 2 LocoNet cables 2.15 m, 3 LocoNet cables 28 cm, 1 LocoNet 5-way distributor, 1 LocoNet branch (1 plug/2 sockets) 2.15 m, the LISSY manual and special instructions for installing and commissioning the station control.
On order, lead time to be confirmed
You can now use MARCo on your digital layout to do everything that was previously only possible with a computer. Without a computer, MARCo makes simple automatic control functions possible, such as block operation and shuttle lines, as well as optimised automatic control of even extensive fiddle yards. MARCo consists of a RailCom transmitter or a RailCom-capable decoder in the locomotives, and a MARCo receiver connected to a track section. The RailCom data are transmitted via the track. The track section must be operated with a RailCom-capable booster such as Power 4. RailCom works only in the DCC data format. MARCo recognises the train and shows which train has entered track 1 of the station. MARCo controls shuttle train operation in the terminus of the single-track branch line. MARCo manages your fiddle yard with through track, independently finds an individual track for each train and, when needed, automatically lets the trains run out of the fiddle yard again. The through track can be used on a locomotive-specific basis or, at the push of a button, by all locomotives. MARCo is a block system for digital layouts and automatically controls the block posts on the layout, without using a computer. MARCo slowly brakes every digital locomotive in front of a red signal using the decoder's internal braking delay. MARCo switches the sound of locomotives depending on the situation, for example the whistle before the tunnel or the horn at the level crossing before the whistle board. MARCo fades out the sound of locomotives fitted with "IntelliSound" when they travel into hidden areas (fiddle yard, tunnel). MARCo switches the lights of a selected locomotive on or off after a certain time, e.g. when the driver has stabled the locomotive. MARCo controls the speed of locomotives, e.g. at station approaches or on slow-speed sections.
On order, lead time to be confirmed
Art. no. 68341 2 in 1... Lissy and RailCom® transmitter Lissy transmitter for all vehicles that are to be used with the Lissy control system. Installed under the vehicle. Railcom transmitter for retrofitting all vehicles that have a DCC decoder that is not yet RailCom®-capable. Installed in the vehicle. The transmitter is installed in addition to the locomotive decoder in/under a locomotive, or individually in coaches (e.g. driving trailers), and is simply connected to the current collection of the locomotive or coach. You can program it, like a DCC decoder, with all short or long DCC addresses. At a size of just 13 x 7 x 1.8 mm, it is significantly smaller than the previous transmitters and finds room under or in almost all vehicles. Art. no. 68341 LISSY/RailCom® transmitter, pack of 5
On order, lead time to be confirmed
The LISSY micro transmitter module is suitable for connection to IntelliDrive 2 or Piko V4.1 decoders. It is designed for locomotives equipped with Uhlenbrock locomotive or sound decoders featuring a LISSY output. It continuously transmits the decoder address and train category. This transmitter module can only be connected to IntelliDrive 2 decoders.
On order, lead time to be confirmed
The LISSY receiver is a module with two small, barely visible IR sensors with a diameter of 3 mm for installation in the track. The connection to the digital central station is via LocoNet.
On order, lead time to be confirmed
For simple switching functions, the LISSY single receiver is available. The sensor is integrated into the module. For assembly, a 4 mm hole is drilled into the base plate between the sleepers, and the receiver is plugged in from below. Connection to the digital central station is made via a LocoNet cable.
On order, lead time to be confirmed
Complementary product for the 68610 LISSY receiver
On order, lead time to be confirmed
The digital universal controller can be used for many automatic control sequences on a layout and is connected to the digital central station via LocoNet. The controller can monitor 4 track sections and, per track section, signal-dependently slow down and stop a train. Each track section is connected to the controller via 2 terminals. One terminal for the running section and one for the braking section.
On order, lead time to be confirmed
Track-Control – the start The starter set contains all the items that are part of the basic equipment and are usually required only once per control panel: a Track-Control connection module 69060 (Note: the depicted Track-Control connection module has been replaced by item 69060), a LocoNet cable, a CD with the planning software and the manual.
On order, lead time to be confirmed
Track-Control – the start The base set contains all items that are part of the basic equipment and are usually required only once per control panel: a Track-Control connection module 69060 (note: the depicted Track-Control connection module has been replaced by item 69060), a LocoNet cable, a CD with the planning software and the manual.
On order, lead time to be confirmed