Electronics
For converting Märklin/Trix H0 locomotives with a built-in high-efficiency motor or other DC motors. The märklin LokDecoder mLD3 has a soldered-on wiring harness. The märklin LokDecoder mLD3 supports the mfx, MM1, MM2 and DCC digital formats. A plug for NEM-652 interfaces, to be soldered on yourself, is included.
In stock: 5 on the shelf, shipped within 1-3 days
Model For 11 plugs to the new standard. All of the connections are electrically connected. The power feed is also possible by means of 1 plug of the earlier version. Size 47 x 26 mm. The Märklin 72090 distribution plate ensures clean, efficient wiring on your layout. All of the connections are electrically connected, so that you can distribute power and signals simply and reliably. Thanks to 11 plug sockets to the new Märklin standard and the option of a power feed by means of older plugs, your layout remains flexible and can be expanded. Highlights Distribution plate with 11 connections to the new Märklin standard All connections electrically connected for simple power distribution Compatible with old and new Märklin plug systems Compact design (47 x 26 mm) for flexible placement
In stock: 5 on the shelf, shipped within 1-3 days
Installation from below.
In stock: 5 on the shelf, shipped within 1-3 days
Model For the 73400 interior lighting. With an asymmetric pickup shoe and a common return spring. Note The combination of 2 x 73400 + 1 x 73404 can replace the previous 7330 or 7335 interior lighting.
In stock: 5 on the shelf, shipped within 1-3 days
With flat plugs for C tracks. 2-pole, red and brown cable. Length 1 m. The 74040 connection set can only be used with the older generation of equipment.
In stock: 5 on the shelf, shipped within 1-3 days
Suitable for Gauge H0. The decoder is equipped with the RailCom function. Maximum motor current: 1.2 A. For further technical data see data sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. Answers to possible questions can be found in this Zimo manual
In stock: 5 on the shelf, shipped within 1-3 days
Decoder for all DC locomotives with a current consumption of up to 1000 mA (motor 1000 mA, lighting 300 mA). Suitable for digital locomotives with a 14-pin digital interface (mTc14). Universally usable in Selectrix/SX2 and DCC format. Automatic digital and analogue detection. Adjustable maximum speed. Adjustable motor pulse variants. Automatic load compensation. Connection for lighting function. Connection for additional function. Short-circuit protection of the motor output. Overload protection of the lighting output. Overload protection of the additional function. Programming of additional settings by selecting address "00", e.g. fine graduation of the pulse widths (control variant), polarity reversal of the direction of travel. in Selectrix operation: 31 speed steps. (Sx2 127 speed steps). 111 addresses. (Sx2 10,000 addresses). 1 additional function (Sx2 16 additional functions). Block section operation with simple diodes (1 or 2 stopping sections). Braking mode with brake diode. in DCC operation: Manual speed step selection 14/28 steps. Automatic switchover to 128 speed steps. Addresses optionally long or short. Braking mode with DC voltage and "broadcast-mode" braking generators. Dimensions approx. 14 x 9 x 1.8 mm.
In stock: 5 on the shelf, shipped within 1-3 days
Item no. 71641 5-piece 6-pin plug NEM 651
In stock: 5 on the shelf, shipped within 1-3 days
12 light boxes - each 3 pieces in 4 different sizes and one house lighting LED white. The light boxes provide completely new clear lighting of each single room. For lighting we recommend our LEDs with connection cable in yellow item 6047, white item 6048 and warm-white item 6046, the boards with an LED in yellow item 6007, white item 6008, warm-white item 6006, boards with two LEDs in yellow item 6018, white item 6017 and warm-white item 6021 or the LED with TV simulation item 5079. Light boxes should be fixed inside the house behind the windows. Light is prevented from shining through. Also suitable for TT and N buildings. Dimensions light boxes: L 1,7 x W 1,8 x H 2,6 cm, L 1,7 x W 1,6 x H 2,1 cm, L 1,7 x W 1,2 x H 1,9 cm, L 1,7 x W 1,4 x H 2,3 cm.
In stock: 5 on the shelf, shipped within 1-3 days
Modern street lamp with plate reflector for a spacious and diffuse illumination. Original located e. g. in the government sector of Berlin and at modern stations. Height: 7,5 cm.
In stock: 5 on the shelf, shipped within 1-3 days
Maintenance free by LED lighting. To be mounted under the ceiling. Ø 0.6 x H 0.6 cm.
In stock: 5 on the shelf, shipped within 1-3 days
Maintenance free by LED lighting. For wall mounting.
In stock: 5 on the shelf, shipped within 1-3 days
The floodlight spots stand out for their extremely high brightness. All spots are movable up-, down- and backwards. Maintenance free by LED lighting. With base socket for easy mounting. Height: 1 cm.
In stock: 5 on the shelf, shipped within 1-3 days
Complete kit. Maintenance free by LED lighting. Prototypical brass mast with base socket for easy mounting. Mounting without soldering and any tool. Height: 7 cm.
In stock: 5 on the shelf, shipped within 1-3 days
High-grade litz wire for low-loss current feed and signal transmission.
In stock: 5 on the shelf, shipped within 1-3 days
Practical cable holder. Outer diameter: 2,4 cm. Inner diameter: 1,7 cm.
In stock: 5 on the shelf, shipped within 1-3 days
15 m reel Red/black Double-core PVC isolation Loads 15 A Cu.-conducter: 24x 0.20 mm blanc Application: Gauge I / Gauge 0 Connection to track
In stock: 4 on the shelf, shipped within 1-3 days
DC 16 V/30 mA Green M 60.202
In stock: 4 on the shelf, shipped within 1-3 days
DC Transparent 14-16 V/80 mA For H0 headlights
In stock: 4 on the shelf, shipped within 1-3 days
Loudspeaker 20mm, round, 4 Ohms, 1~2W, with sound chamber When selecting the loudspeaker the used decoder type is important. Depending on the decoder, different loudspeakers can be used as follows: LokSound V4.0 / 5 , LokSound micro V4.0 / 5 and LokSound V4.0 M4 decoders need the new speaker with an impendance of 4 Ohms . With the present 100 Ohms loudspeakers you would hardly hear anything. Conversely, you must never use the new 4 Ohms speakers with the previous LokSound V3.5 decoder. The decoder could be destroyed! When the decoder is replaced, the speaker must! be changed as well. Art.No. Delivery 50321 Loudspeaker 15mm x 11mm, 8 Ohms, with 4pc sound chamber kit 50325 Loudspeaker 16mm x 35mm square, 8 Ohms, 1~2W, with sound chamber 50326 Loudspeaker 14mm x 12mm square, 8 Ohms, 1~2W, with integrated sound chamber 50330 Loudspeaker 16mm x 25mm, rechteckig, 4 Ohms, with sound chamber 50331 Loudspeaker 20mm, round, 4 Ohms, 1~2W, with sound chamber 50332 Loudspeaker 23mm, round, 4 Ohms, 1~2W, with sound chamber 50333 Loudspeaker 28mm, round, 4 Ohms, 1~2W, with sound chamber 50334 Loudspeaker 20mm x 40mm, square, 4 Ohms, with sound chamber
In stock: 4 on the shelf, shipped within 1-3 days
LokSound 5 micro DCC/MM/SX/M4 "blank decoder", single wires, with Speaker 11x15mm, gauge: N, TT, H0 The LokSound 5 micro is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles. All LokSound decoders are equipped with a Next18 interface and are available with adapter plugs to suit all popular digital interface types. The decoder is supplied with an 11mm x 15mm sugar cube speaker as well as a sound enclosure set. The LokSound 5 micro DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Please note the LokSound 5 DCC decoder does not come with a speaker. Operating modes The LokSound 5 micro is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Control Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound decoder supports the Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables the automatic commuting between two stations. The LokSound 5 micro decoder is also suitable for analogue DC and AC (!) layouts. Sound The LokSound 5 micro decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A double class D audio power amplifier with up to 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions Despite its small dimensions the LokSound 5 micro decoder has at least 6 amplified function outputs as well as one logic output. There are two more logic outputs on the Next18 interface, which alternately may be employed to control RC servos. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for reliable operation of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. Motor control Motor control of the LokSound 5 micro has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 micro decoder supplies sufficient motor current (up to 0.75 A) for the intended applications. LokSound 5 micro DCC The LokSound 5 Micro DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Betrieb unter DCC mit RailComPlus®, M4, Motorola® und Selectrix® 32 Funktionen schaltbar (abhängig von der Zentrale) 32-Bit-Prozessor Digitaler Class-„D“-Verstärker mit bis zu 3 W Leistung (LokSound 5 XL: 13 W) Jeder Kanal in 16-Bit-Auflösung und 31250 kHz Samplerate Geräuschspeicher mit 128 Mbit Kapazität Motorregelung mit 50 kHz Taktfrequenz RC-Servos und Susi-Module ansteuerbar 3 neue, individuell einstellbare Bremsregler Zweistufige Schwerlast-Simulation Updatefähig mit ESU-LokProgrammer LokSound 5 micro Motorstrom 0,75 A Je nach Schnittstelle bis zu 6 verstärkte Funktionsausgänge für Sonderfunktionen (total: 9 Ausgänge) Next18-Schnittstelle serienmäßig, Adapterkabel für andere Schnittstellen liegen bei Ab Werk mit 11x15-mm-„Zuckerwürfel“-Lautsprecher mit anpassbarem Schallkapsel-Set RC-Servos und Susi-Module ansteuerbar PowerPack-Speicherkondensator optional anschließbar Abmessungen: 21 mm x 10 mm 8-pin NEM 652 PluxX16 6-pin NEM 651 Next18 Click the image for a bigger view. Instruction manual Art.No. Delivery 58820 LokSound 5 micro DCC "blank decoder", 8-pin NEM652, gauge: N, TT, H0 Only available at ESU LLC! 58823 LokSound 5 micro DCC "blank decoder", single wires, gauge: N, TT, H0 Only available at ESU LLC! 58828 LokSound 5 micro DCC "blank decoder", Next18, gauge: N, TT, H0 Only available at ESU LLC! 58810 LokSound 5 micro DCC/MM/SX/M4 "blank decoder", 8-pin NEM652, with Speaker 11x15mm, gauge: N, TT, H0 58813 LokSound 5 micro DCC/MM/SX/M4 "blank decoder", single wires, with Speaker 11x15mm, gauge: N, TT, H0 58816 LokSound 5 micro DCC/MM/SX/M4 "blank decoder", 6-pin NEM651, with Speaker 11x15mm, gauge: N, TT, H0 58818 LokSound 5 micro DCC/MM/SX/M4 "blank decoder", Next18, with Speaker 11x15mm, gauge: N, TT, H0 51993 Wire harness, 18-pin Next18 socket to open wires, 88mm, with heat shrink tube 51994 Adapter board, 18-pin Next-18 socket to NEM651 6-pin, Flex, 88mm, with heat shrink tube 51995 Adapter board, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube 51996 Adapter board, 18-pin Next-18 socket to Plux16
In stock: 4 on the shelf, shipped within 1-3 days
LokSound 5 micro DCC/MM/SX/M4 "blank decoder", 6-pin NEM651, with Speaker 11x15mm, gauge: N, TT, H0 The LokSound 5 micro is a “little wonder”: With only 21mmx10mm footprint, it is by far one of the smallest LokSound decoders we’ve ever built. Thus it should fit into all N gauge and TT vehicles, but is also suitable for small H0 vehicles. All LokSound decoders are equipped with a Next18 interface and are available with adapter plugs to suit all popular digital interface types. The decoder is supplied with an 11mm x 15mm sugar cube speaker as well as a sound enclosure set. The LokSound 5 micro DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Please note the LokSound 5 DCC decoder does not come with a speaker. Operating modes The LokSound 5 micro is a true multi protocol decoder. It supports DCC as well as Motorola®, Selectrix® and M4. Of course it supports 14 through to 128 speed steps as well as 2 and 4 digit addresses in DCC format and up to 32 functions. Thanks to RailComPlus® the decoders register themselves fully automatically on suitable command stations. This decoder supports all DCC programming modes and thanks to RailCom® you may read out the CV values on the main, provided you have a command station supporting RailCom®. There are utility registers for command stations that only facilitate programming of CVs ranging from 1 to 255. Motorola® users benefit from up to 28 speed steps for 255 addresses. Three additional Motorola® addresses facilitate triggering of 16 functions. An integral programming mode even allows programming with the good old Control Unit 6021. The M4 protocol supports the automatic registration on mfx® compatible central units. The LokSound decoder supports the Märklin® braking sections just as well as the ZIMO® HLU braking commands or the Lenz® ABC system. Braking with DCC brake generators or with DC is also possible. Furthermore the locomotive with a LokSound will come to a halt when a Selectrix® braking diode is switched into the circuit. The ABC push-pull feature enables the automatic commuting between two stations. The LokSound 5 micro decoder is also suitable for analogue DC and AC (!) layouts. Sound The LokSound 5 micro decoder can reproduce up to 10 channels simultaneously. Each channel offers up to 16 Bit / 31250 kHz and thus we have finally achieved hi-fi sound quality on your layout. For all practical purposes one cannot detect any difference to the original. A double class D audio power amplifier with up to 3W output power feeds the speakers with a permitted impedance of 4 – 32 Ohms. The huge 128 MBit sound memory assures sufficient storage capacity. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. The volume of all individual sound fragments may be adjusted separately. The outstandingly flexible sound engine without a rigid flow chart facilitates a prototypical simulation of all conceivable rail vehicles. Three separately adjustable braking functions and two alternative load scenarios provide you with maximum control of your vehicles. Functions Despite its small dimensions the LokSound 5 micro decoder has at least 6 amplified function outputs as well as one logic output. There are two more logic outputs on the Next18 interface, which alternately may be employed to control RC servos. Of course, all important lighting functions are supported. The brightness of each output may be adjusted separately. The decoder supports the automatic push and pull movements – known as the coupler waltz - required for reliable operation of digital couplers such as the ones by ROCO® and Krois® as well as Telex® couplers. Motor control Motor control of the LokSound 5 micro has been further improved. A variable PWM pulse frequency ranging from 10 kHz to 50 kHz assures perfect silent operation, particularly for coreless motors. Thus the typical hum is a thing of the past. Load control can now be adjusted with up to 10 separate CVs and thus will manage even the most difficult cases. The unique “Auto Tune” function facilitates the automatic calibration of the decoder to perfectly match the motor. The LokSound 5 micro decoder supplies sufficient motor current (up to 0.75 A) for the intended applications. LokSound 5 micro DCC The LokSound 5 Micro DCC is made for the North American and Australian markets. It is a pure DCC Decoder, which supports RailComPlus and can also be used on DC layouts. Betrieb unter DCC mit RailComPlus®, M4, Motorola® und Selectrix® 32 Funktionen schaltbar (abhängig von der Zentrale) 32-Bit-Prozessor Digitaler Class-„D“-Verstärker mit bis zu 3 W Leistung (LokSound 5 XL: 13 W) Jeder Kanal in 16-Bit-Auflösung und 31250 kHz Samplerate Geräuschspeicher mit 128 Mbit Kapazität Motorregelung mit 50 kHz Taktfrequenz RC-Servos und Susi-Module ansteuerbar 3 neue, individuell einstellbare Bremsregler Zweistufige Schwerlast-Simulation Updatefähig mit ESU-LokProgrammer LokSound 5 micro Motorstrom 0,75 A Je nach Schnittstelle bis zu 6 verstärkte Funktionsausgänge für Sonderfunktionen (total: 9 Ausgänge) Next18-Schnittstelle serienmäßig, Adapterkabel für andere Schnittstellen liegen bei Ab Werk mit 11x15-mm-„Zuckerwürfel“-Lautsprecher mit anpassbarem Schallkapsel-Set RC-Servos und Susi-Module ansteuerbar PowerPack-Speicherkondensator optional anschließbar Abmessungen: 21 mm x 10 mm 8-pin NEM 652 PluxX16 6-pin NEM 651 Next18 Click the image for a bigger view. Instruction manual Art.No. Delivery 58820 LokSound 5 micro DCC "blank decoder", 8-pin NEM652, gauge: N, TT, H0 Only available at ESU LLC! 58823 LokSound 5 micro DCC "blank decoder", single wires, gauge: N, TT, H0 Only available at ESU LLC! 58828 LokSound 5 micro DCC "blank decoder", Next18, gauge: N, TT, H0 Only available at ESU LLC! 58810 LokSound 5 micro DCC/MM/SX/M4 "blank decoder", 8-pin NEM652, with Speaker 11x15mm, gauge: N, TT, H0 58813 LokSound 5 micro DCC/MM/SX/M4 "blank decoder", single wires, with Speaker 11x15mm, gauge: N, TT, H0 58816 LokSound 5 micro DCC/MM/SX/M4 "blank decoder", 6-pin NEM651, with Speaker 11x15mm, gauge: N, TT, H0 58818 LokSound 5 micro DCC/MM/SX/M4 "blank decoder", Next18, with Speaker 11x15mm, gauge: N, TT, H0 51993 Wire harness, 18-pin Next18 socket to open wires, 88mm, with heat shrink tube 51994 Adapter board, 18-pin Next-18 socket to NEM651 6-pin, Flex, 88mm, with heat shrink tube 51995 Adapter board, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube 51996 Adapter board, 18-pin Next-18 socket to Plux16
In stock: 4 on the shelf, shipped within 1-3 days
LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl. The decoder accepts all DCC programming modes and thanks to RailCom® the CV values can be read on the main track with RailCom equipped DCC systems. For command stations that only program the CVs from 1-255 auxiliary CV registers exist. The LokPilot 5 DCC decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACKCommands or the Lenz® ABC system. Also braking with DCC brake modules or with DC voltageis possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle trainenables automatic commuting between two train stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The top speedcan be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5DCC packed with function outputs. Depending on the interface version, each LokPilot offers 5 DCCDecoder at least 10 amplified function outputs with 250mA output current each. In the executionswith PluX22 or 21MTC interface there are 4 outputs to control servos orLogic level outputs added. All-important lighting functions are available. The brightness of each outputcan be set separately. The decoder masters automatic pushing and pullingwhen uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 DCC has been fundamentally improved again. A variably adjustablePWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors.Operation - The typical “hum” is a thing of the past. The load control now has up to10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enablesthe automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to 1.5A of motor current. Enough juice even for older motors. Operational safety On request, a PowerPack can be fitted to the LokPilot 5 DCC to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Analog Gleichspannung (abschaltbar). Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59620 LokPilot 5 DCC, 8-pin NEM652, gauge H0 ,0 59622 LokPilot 5 DCC, PLUX22 NEM658, gauge H0 ,0 59626 LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 59629 LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 59659 LokPilot 5 DCC, 21MTC MKL, gauge H0 ,0
In stock: 4 on the shelf, shipped within 1-3 days
LokPilot 5 micro DCC, Next18, gauge N, TT The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. With just 8.0mm x 7.0mm and a thickness of only 2.4mm (on the capacitor: 2.9mm), just so small that it can also be accommodated in very small locomotives of nominal sizes Z, N or TT, it is a pure DCC Decoder. This lack of flexibility is rewarded with a lower price. LokPilot 5 micro DCC decoders are available with all common interfaces. The variants with Next18 or PluX16 interface are a bit larger with a base area of 13.0mm x 9.2mm, but have 2 additional function outputs. Modes The LokPilot 5 micro DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to Rail¬ComPlus®, the decoders log on to a suitable DCC System fully automatically. It masters all DCC programming command stations. Auxiliary registers exist for DCC systems that can only program CVs from 1-255. The LokPilot 5 micro DCC decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle train enables automatic commuting between two stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The maximum speed can be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5 micro DCC equipped with an amazing number of function outputs. The variants with 6-pin or 8-pin Wiring harnesses offer 4 amplified function outputs, each with 180mA output current and two logic level outputs. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs available. All important lighting effects are available. The brightness of each output can be adjusted separately. The decoder masters automatic pushing and pulling when uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The motor control of the LokPilot 5 micro DCC has been fundamentally improved again. A variable adjustable PWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors- The typical “hum” is a thing of the past. The load control now has up to 10 CVs which can be adjusted for difficult cases. The unique "Autotune" function enables the automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to .75A of motor current. Enough juice for most motors. Safety A PowerPack to bypass dirty track can be fitted to the LokPilot 5 micro. Protection Of course, the motor output and the function outputs are against overload protected. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59820 LokPilot 5 micro DCC, 8-pin NEM652, gauge N, TT 59824 LokPilot 5 micro DCC, PluX16, gauge N, TT 59826 LokPilot 5 micro DCC, 6-pin NEM651, gauge N, TT 59827 LokPilot 5 micro DCC, 6-pin Direkt, gauge N, TT 59828 LokPilot 5 micro DCC, Next18, gauge N, TT 59857 LokPilot 5 micro DCC, 6-pin Direkt gewinkelt, gauge N, TT
In stock: 4 on the shelf, shipped within 1-3 days