Electronics
25 m reel Red/brown Double-core For Märklin® PVC isolation Loads 5 A Cu.-conducter 14 x 0.15 mm Connection to track
In stock: 1 on the shelf, shipped within 1-3 days
72 mm long 1 piece
In stock: 1 on the shelf, shipped within 1-3 days
For illumination of industrial buildings New mould wide angle of reflection (160°), for perfect illumination of buildings Ø 1,5 cm, round Light: warm white Low power input Virtually unlimited service life due to LED technology With 2 cables With 2 mounting lug Individual, packed in bag Connection: max. 19 V We recommend a operating voltage of 12 V DC
In stock: 1 on the shelf, shipped within 1-3 days
A 5 m reel of flat cable with a cross-section of 0.14 mm².
In stock: 1 on the shelf, shipped within 1-3 days
A versatile street light with a mast made of real wood. Also suitable for industrial sites and other areas. Features a replica of the concrete surround at the base of the lamp.
In stock: 1 on the shelf, shipped within 1-3 days
Model of a mobile phone mast with warning light at the top (red LED). For connection to 14–16 V DC or AC. Height: approx. 175 mm.
In stock: 1 on the shelf, shipped within 1-3 days
You can almost smell the sausages sizzling on the barbecue... A “brick-built” surround with a campfire illuminated by 2 light bulbs and an electronic control circuit. The matching sausages and steaks are supplied with the grill grate. Includes a wooden table, 2 wooden benches and 6 tree stumps as additional seating.
In stock: 1 on the shelf, shipped within 1-3 days
A 10 m reel. Special cable with a diameter of only 0.25 mm (YV wire, 0.05 mm²) with super-thin plastic insulation.
In stock: 1 on the shelf, shipped within 1-3 days
A 10 m reel. Special cable with a diameter of only 0.25 mm (YV wire, 0.05 mm²) with super-thin plastic insulation.
In stock: 1 on the shelf, shipped within 1-3 days
IR transmitter and receiver 18 x 9 x 20 mm. The range is max. 100 mm with electronic relay 5740 and control board 5745, max. 250 mm with timer 5961/5963.
In stock: 1 on the shelf, shipped within 1-3 days
Bus distribution plate with 0.9 m cable, connected to the „Extend“ jack of the ECoS or Central Station: two jacks for hand controllers on the front panel, four sockets at the back for ECoSBoost boosters and ECoSDetector feedback modules.
In stock: 1 on the shelf, shipped within 1-3 days
L.Net Converter to connect handheld throttles and feedback modules to ECoS or CS1 »Reloaded« The great variety of the ESU ECoS command station is so convincing to many model railroaders that they would like to replace their present digital station with an ECoS. This also has been inspiring the desire to continue to use the existing handheld throttles and feedback modules. The ECoSniffer input offered at least a solution for handheld throttles (in combination with „older"digital command stations), whereas the feedback modules couldn’t be integrated into the system. For the first time, it is possible to connect Uhlenbrock® or Digitrax® handheld throttles directly to the ECoS or Central Station 60212 „Reloaded", thanks to the ESU L.Net Converter. Additionally, you can continue to use feedback devices which support the well-known Loconet® communication protocol. So, what can the L.Net Converter do now? Handheld throttle throughout With the L.Net Converter you are able to operate Loconet® compatible handheld throttles directly with your ECoS. Hereby, the handheld throttle´s display will always stay synchronised with the ECoS. Furthermore there is no restriction to one data format. You can control an unlimited number of locos speaking DCC, Motorola®, Selectrix® or M4®, even if the handheld throttle alone does not have the capability to do this. Particularly in Germany the popular Daisy®-, Fred®- or ProfiBoss® handheld throttles can be used, as well as e.g. DT400 or UT2 by Digitrax®. The L.Net Converter fully integrates them into the ECoS system. Via the ECoS you are able to assign the locos desired and call them up on the handheld throttle; or respectively use the easy-to-handle Fred® handheld throttles to assign the loco desired conveniently to the ECoS. Feedback modules You might already have Loconet® feedback modules for track occupancy detection. With the aid of the L.Net Converter you may now continue to use those devices. The ECoS allows you to use the contacts for activating routes or shuttle train control. Of course you can simultaneously use s88, Loconet® and ECoSDetector feedback modules. Communication Just larger layouts are operated with the support of a PC. Often there is used a self-made software, which has been optimised for Loconet®. The switch to an ECoS system which comes as an innovative and object-based communication model is thus quite rocky. However, the L.Net Converter will solve this problem. From now on, the ECoS will send loco and turnout commands via the L.Net Converter to the devices connected. The intelligent ESU L.Net Converter allows you finally to replace your »old« command station completely with an ECoS without great effort. Art.No. 50097 L.Net Converter to connect handheld throttles and feedback modules to ECoS or CS1 »Reloaded« Connection example of handheld throttles (schematical)
In stock: 1 on the shelf, shipped within 1-3 days
Loudspeaker 15mm x 11mm, 8 Ohms, with 4pc sound chamber kit When selecting the loudspeaker the used decoder type is important. Depending on the decoder, different loudspeakers can be used as follows: LokSound V4.0 / 5 , LokSound micro V4.0 / 5 and LokSound V4.0 M4 decoders need the new speaker with an impendance of 4 Ohms . With the present 100 Ohms loudspeakers you would hardly hear anything. Conversely, you must never use the new 4 Ohms speakers with the previous LokSound V3.5 decoder. The decoder could be destroyed! When the decoder is replaced, the speaker must! be changed as well. Art.No. Delivery 50321 Loudspeaker 15mm x 11mm, 8 Ohms, with 4pc sound chamber kit 50325 Loudspeaker 16mm x 35mm square, 8 Ohms, 1~2W, with sound chamber 50326 Loudspeaker 14mm x 12mm square, 8 Ohms, 1~2W, with integrated sound chamber 50330 Loudspeaker 16mm x 25mm, rechteckig, 4 Ohms, with sound chamber 50331 Loudspeaker 20mm, round, 4 Ohms, 1~2W, with sound chamber 50332 Loudspeaker 23mm, round, 4 Ohms, 1~2W, with sound chamber 50333 Loudspeaker 28mm, round, 4 Ohms, 1~2W, with sound chamber 50334 Loudspeaker 20mm x 40mm, square, 4 Ohms, with sound chamber
In stock: 1 on the shelf, shipped within 1-3 days
Loudspeaker 40mm round, 8 Ohms, with sound chamber for LokSound H0, LokSound XL decoders work with loud speakers which have an impendance from 8-32 Ohms. ESU offers you a selection of the sizes 40mm, 57mm and 78mm includung sound chamber as well as some high-class Visation XL loudspeakers without sound chamber. Visaton loudspeakers offer a powerful bass and a high-quality audio playback, whereas ESU loudspeakers are also suitable for open-land vehicles due to their plastic membrane. 50336 50336 50337 50337 50446 Part No. 50322 Loudspeaker Monacor Sp6/4SQ, 59mm, round, 8 Ohms, for PIKO G/LGB Loks 50323 Loudspeaker 40mm round, 8 Ohms, with sound chamber for LokSound H0, LokSound XL 50324 Loudspeaker Visaton FRS 7, 70mm, round, 8 Ohms 50336 Loudspeaker Visaton SC4.7ND, 41x70mm, square, 8 Ohms 50337 Loudspeaker Visaton FRS5, 50mm, round 8 Ohms 50446 Loudspeaker 78mm, round, 8-32 Ohms, with sound chamber Expires
In stock: 1 on the shelf, shipped within 1-3 days
Two loudspeakers 16mm, oval, je 50 Ohm, with sound chamber For the well-proven LokSound V3.5, LokSound micro V3.5 and LokSound V3.0 M4 decoders we offer loudspeakers in the following sizes: 2x13mm (50 Ohms each), 2x16mm (50 Ohms each), 16x25mmm, 20mm, 23mm, 28mm, 20x40mm and 40mm. By virtue of the internal design of the decoders, the speakers feature a specially customised impedance of 100 Ohms. Only these speakers may be used! Art.No. 50335 Loudspeaker 32mm, rund, 100 Ohm, without sound chamber Expires 50442 Loudspeaker 23mm, round, 100 Ohm, with sound chamber Expires 50444 Loudspeaker 40mm, round, 100 Ohm, with sound chamber Expires 50447 Two loudspeakers 16mm, oval, je 50 Ohm, with sound chamber Expires 50448 Loudspeaker 20mm x 40mm, square, 100 Ohm, with sound chamber Expires
In stock: 1 on the shelf, shipped within 1-3 days
LED lighting strip with taillight, 255mm, 11 LEDs, „yellow“. For gauge N,TT, H0 The 255mm long, 9mm slim LED lighting strips with 11 LEDs are designed for N, TT and H0 gauge cars. We are offering two versions: The version with Part number 50700 is equipped with warmwhite LEDs, while on part number 50702 we installed yellow LEDs. This will give you the choice to match the lighting strips with your existing cars. As usual for all ESU lighting strips, you can adjust the brightness according to your wishes with the help of a small variable resistor (potentiometer). Thanks to built-in voltage control the brightness remains almost constant even when conventional driving. To bridge prolonged power interruptions, you may add a PowerPack. Of course, the lighting strips can be arbitrarily cut to fit the cars of all manufacturers and comes with a red taillight. You may add a LokPilot Fx V4.0 function decoder at any time. Part No. 50700 LED lighting strip with taillight, 255mm, 11 LEDs, „warm-white“. For gauge N,TT, H0 50702 LED lighting strip with taillight, 255mm, 11 LEDs, „yellow“. For gauge N,TT, H0
In stock: 1 on the shelf, shipped within 1-3 days
LED lighting strip, cabin, 1 LED, „warm-white“, 15,0mm x 6,9mm x 2,3 mm Small modules that can easily be installed either in cabs or as end-of-train lights make fitting protypical lighting of your vehicles a simple task. They provide one warmwhite LED or two red LEDs including the needed electronics. Part No. 50704 LED lighting strip, cabin, 1 LED, „warm-white“, 15,0mm x 6,9mm x 2,3 mm 50705 LED lighting strip, taillight, 2 LED, „Red“
In stock: 1 on the shelf, shipped within 1-3 days
SwitchPilot Extension, 4 twin-relays (DPDT) output, 2A each, extension for Switch Pilot Family If required, SwitchPilot can be augmented with the SwitchPilot Extension Modul: Plugged in at the side of the SwitchPilot, it offers four relay-driven outputs, used for switching potential-free loads, or for polarizing the frog; the ideal supplement for tricky circuitry. Modes of operation The SwitchPilot Extension Modul only works in conjunction with a SwitchPilot. Plugged in at the side, it gets its electrical power directly from the SwitchPilot. It contains a total of 4 Twin-Relays (2 x DPDT), of which each is dedicated to a pair of transistorized SwitchPilot outputs. The respective relay’s switch position is directly dependent upon the state of this pair of outputs. With the relay’s help, loads can be switched, galvanically separated from the rest of the track (it functions like a k84), or a motorized turnout can be polarized. With the relay’s 1.5 Amp continuous rating, either frogs can be polarized-, or blocks powered signal dependent, or motorized devices, such as (water) pumps may be switched. Especially intricate is the option to control motorized turnouts: Of course the SwitchPilot Extension Module easily handles the necessary motor polarization as well.
In stock: 1 on the shelf, shipped within 1-3 days
SwitchPilot 3 Servo, 8x servo decoder, DCC/MM, OLED, with RC-Feedback, updatable SwitchPilot 3 servo decoders are optimized for stationary use on your system and can control up to eight RC servo drives. In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 Servo has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons. Modes The SwitchPilot 3 servo is multi-protocol and can be used with workstations according to the Märklin® Motorola® system (e.g. 6021, Central Station® or Mobile Station®) as well as DCC-enabled central. The configuration can take place on both the main track and the programming track. Thanks to RailCom®, CVs can also be read out. Functioning The SwitchPilot 3 servo can be supplied directly from the digital system or an external DC or AC voltage source. The SwitchPilot 3 servo has eight outputs for the control of RC servo drives. In doing so, it can control these drives so precisely that, in addition to switching switches, any other slow movement sequences can be controlled. The SwitchPilot 3 servo has a built-in power-on pulse suppression to eliminate or reduce the system-related "twitching" of RC servos when applying the supply voltage. Furthermore, the power supply to the servo can be interrupted to prevent a "hum" of some inexpensive servos. Each of the eight servos can be operated either in "digital mode" or in the "proportional mode" introduced for the first time with the SwitchPilot 3 servo: In digital mode, the servo can start two end positions "A" and "B", depending on the switching position on the control panel. The position of the two end positions as well as the speed at which thethe servo moves in the desired direction, can be individually set on the SwitchPilot 3 servo. The digital mode is perfect for switching switches or signals that should always remain in a fixed position. In proportional mode, the servo can move and stop in any position within the end positions "A" and B. The servo only runs as long as the control panel sends a command. If you release the button, the servo stops. In this way, a servo can be stopped in any desired position. The servo speed can be adjusted individually. The proportional mode is ideal for (water) cranes or engine shed gates or any other application, for which intermediate positions are also required. For each servo, in addition to the end positions and the rotational speeds, it can be determined whether it should rock up when reaching the final position. Furthermore, the generation of the servo pulse can be influenced to adapt to the different RC servos on the market or the power supply of each servo can be switched off individually. In this way, cheap so-called so-called Analog servos as well as modern digital servos (with microcontroller) optimally controlled. Analogue Operation The SwitchPilot 3 servo can be used as a special feature without a digital control panel: On request, up to 16 buttons can be connected for direct switching of the servos. Set The SwitchPilot 3 servo can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom® CVs. On request, he also learns the addresses directly via a programming button. The setting is, of course, the simplest with the integrated OLED displays as well as the three input buttons: All (!) Settings can be checked directly on the decoder and changed on request. "Programming" with the help of your headquarters is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 servo are protected against overload. We want you to enjoy your decoder for as long as possible.
In stock: 1 on the shelf, shipped within 1-3 days
Super thin cable, 0.5mm diameter, AWG36, 10m bundle, white colour Who doesn’t know the problem: if you work on locos and decoders (e.g. run wires from loco to tender), you need thin, extremely flexible cables. These are not always easy to get. Responding to many requests from our customers, as of now we offer you super thin cables (AWG 36) with an outside diameter of only 0.5 mm (0.02 inch), in all common DCC colors. They come in 10 m (30 feet) bundles at an affordable price. If the loco in question features no digital interface and you don’t want to cut off the interface-plug of your loco, simply make use of one of our harnesses 51950 resp. 51951: Solder in the harness and then plug in the decoder. That’s how the Pro’s do it!
In stock: 1 on the shelf, shipped within 1-3 days
Adapterplatine PluX22 for 9 outputs, with soldering pads and wires Our new adapter board 3 for decoders with PluX22 interface is best suited for everyone intending to digitise a loco without interface but with many functions without having to carry out major soldering work. The adapter board with its compact dimensions of 32.5mm x 15.5mm is equipped with an extra mounting lug that can be easily broken off if not required. All outputs as per VHDM resp. NEM standard are accessible as soldering pads. For easy handling and wiring the most important contacts are already equipped with 200mm long wires. Dimensions: Length 33.0mm x 15.5mm (With mounting tab: 38.0mm x 15.5mm) Art.No. Delivery 51958 Adapterplatine PluX22 for 9 outputs, with soldering pads and wires
In stock: 1 on the shelf, shipped within 1-3 days
Smoke distillate, 125 ml bottle Developed specially for the diesel and steam locomotives of the ESU Engineering Edition. It produces realistically dense, white smoke and evaporates without residue: no traces in the smoke generator, on locomotive or building roofs, or on the layout. It wipes off easily with alcohol and does not attack the paintwork or patina of your models. It also works in all other known smoke generators, in locomotives as well as ship models and model buildings. Danger: may be fatal if swallowed and enters airways. Store locked up. If swallowed, immediately call a poison centre or doctor; do not induce vomiting.
In stock: 1 on the shelf, shipped within 1-3 days
Adapter cable, 18-pin Next-18 socket to NEM651 6-pin, Flex, 88mm, with heat shrink tube Sometimes, the locomotive is still equipped with an "old" 6-pin interface compliant with NEM 651. Using this flexible PCB, which can be folded and cut to length almost at will, you can easily install a modern decoder with a Next18 interface. The adapter board comes with heat-shrink tubing. Art.No. Delivery 51994 Adapter cable, 18-pin Next-18 socket to NEM651 6-pin, Flex, 88mm, with heat shrink tube
In stock: 1 on the shelf, shipped within 1-3 days
Adapter cable, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube Due to space constraints, some HO locomotives with the "old" 8-pin NEM-652 interface cannot accommodate a standard HO decoder. With the help of this flexible PCB, which can be folded and cut to length as needed, you can install a modern, compact N-scale decoder featuring a Next18 interface. The adapter board comes with heat-shrink tubing. Art.No. Delivery 51995 Adapter cable, 18-pin Next-18 socket to NEM652 8-pin, Flex, 88mm, with heat shrink tube
In stock: 1 on the shelf, shipped within 1-3 days