Skip to main content Skip to search Skip to main navigation
Swiss model railway specialists Shipped from Switzerland Märklin · Trix · LGB

Electronics

Command stations, decoders, boosters and wiring for digital control, whatever your system.
Filter products
18-pin Next18 to PluX16 adapter cable
ESU 51996
18-pin Next18 to PluX16 adapter cable

Adapter board, Next18 socket to Plux16 Some N or TT scale models are equipped with a PluX16 interface. This adapter board is suitable for installing a LokSound 5 micro or LokPilot 5 micro in such models; simply plug it in between the locomotive and the vehicle to use a decoder with a Next18 interface. Please take the installation depth and available space into account. Art.No. Delivery 51996 Adapter board, Next18 socket to Plux16

Regular price: CHF 6.40

In stock: 1 on the shelf, shipped within 1-3 days

PowerPack Mini Pack for LokPilot V4.0
ESU 54671
PowerPack Mini Pack for LokPilot V4.0

PowerPack Mini enery buffer for LokPilot V4.0, LokSound V4.0, LokPilot 5 family and LokSound 5 family, 1F/2.7V The new ESU PowerPack Mini can be wired to all fourth and fifth generation ESU decoders. It reliably supplies energy to your locomotive when traversing dirty track or long turnout ladders. With its energy storage (1 Farad capacity) the unit supplies power to all light and motor functions as well as to the sound module. Subject to the energy consumption of your model it may continue to move for up to three seconds. The PowerPack Mini incorporates an integral charging circuit controlled by the decoder. Therefore it may be connected even during programming. In order to avoid an undue load on the booster in case there are several models in the same booster sector, the charging current is limited. The buffer time can be reduced by means of a CV. This may be useful to assure the correct stopping position ahead of signals showing the “Stop” aspect (red signal). Although it is considerably smaller than its predecessor, the space requirements of the PowerPack Mini of about 15.7 mm x 9.7 mm x 13 mm must be taken into account when installing this unit. A three-pole wire harness connects the PowerPack Mini to the decoder. The wires are already soldered to the PowerPack Mini and must be soldered to the appropriate solder pads of the decoder. Please note that the PowerPack cannot operate in analogue mode due to technical reasons: Buffering is therefore not possible in analogue mode. Art.No. Delivery 54671 PowerPack Mini enery buffer for LokPilot V4.0, LokSound V4.0, LokPilot 5 family and LokSound 5 family, 1F/2.7V

Regular price: CHF 47.50

In stock: 1 on the shelf, shipped within 1-3 days

LokSound 5 micro DCC Direct Kato Japan N
ESU 58731
LokSound 5 micro DCC Direct Kato Japan N

LokSound 5 micro DCC Direct Kato Japan »Blank decoder«, gauge: N The LokSound 5 micro DCC Direct Kato Japan has been specially developed for installation in Kato-branded track N vehicles: in many European and Japanese locomotives of this manufacturer, the ser decoder can be installed directly below the engine instead of the analog board installed as standard. Finally, these models can also be easily retrofitted with a LokSound decoder. The LokSound 5 micro DCC Direct Kato Japan with its dimensions of 27.6mm x 14.1mm x 3mm is a pure DCC decoder and comes without a loudspeaker. Modes The LokSound 5 micro DCC Direct Kato Japan is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully to a suitable digital center.It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokSound 5 micro DCC Direct Kato Japan Decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible. In addition, it also stops with a Selectrix® brake diode. An AUTOMATIC ABC commuter train allows automatic commuting between two stations. The LokSound 5 micro DCC Direct Kato Japan can be used on analog DC webs.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Sound The LokSound 5 micro DCC Direct Kato Japan Decoder can play up to 12 channels simultaneously. Each channel can be resolved with up to 16 bits / 31250 kHz and offers hi-fi quality on its system. There is virtually no difference to the original audible anymore. A Class-D audio output with up to 3W output power controls the speakers, which can have between 4 ohms and 32 ohms impedance. A 128 Mbit sound memory provides enough capacity. All individual noises can be adjusted individually in the volume. The super-flexible sound engine without a rigid schedule allows the exemplary simulation of all conceivable rail tracks. Functions Although the LokSound 5 micro DCC Direct Kato Japan is normally installed in the motor car of a drive car set, three reinforced function outputs for lighting are available at their own discretion. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokSound 5 micro DCC Direct Kato Japan has a variable PWM clock frequency from 10kHz to 50kHz, which ensures a super-quiet drive, especially for bell anchor motors – the typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. The LokSound 5 micro DCC Direct Kato Japan Decoder delivers up to 0.9A motor power. Protection Of course, the outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Art.No. Delivery 58731 LokSound 5 micro DCC Direct Kato Japan »Blank decoder«, gauge: N

Regular price: CHF 115.00

In stock: 1 on the shelf, shipped within 1-3 days

LokSound 5 Nano DCC single wires 11x15mm N TT
ESU 58923
LokSound 5 Nano DCC single wires 11x15mm N TT

With the LokSound 5 Nano DCC, ESU has succeeded in developing an even smaller LokSound decoder! Thus, it should really be used in all vehicles of nominal sizes N and TT.

Regular price: CHF 115.00

In stock: 1 on the shelf, shipped within 1-3 days

LokPilot 5 Basic 8-Pin NEM652 gauge H0 0
ESU 59020
LokPilot 5 Basic 8-Pin NEM652 gauge H0 0

LokPilot 5 Basic, 8-pin NEM652, Gauge H0, 0 While LokPilot 5 decoders can undoubtedly meet all imaginable requirements of even the most demanding experts, many model railway eras are looking for a robust, high-quality DCC decoder for your standard requirements, which should also be affordable. The LokPilot 5 Basic was developed with the aim of offering a modern decoder with a reasonable range of functions at a reasonable price. The LokPilot 5 Basic comes in two versions: In addition to a version with an 8-pin NEM interface, a version with 21MTC interface is also available. This makes the LokPilot 5 Basic particularly suitable for use in track H0 vehicles. Modes The LokPilot 5 Basic is a "pure-bred" DCC decoder. 14 to 128 driving steps are as self-evident as 2- and 4-digit addresses. Up to 20 functions can be triggered. Thanks to RailComPlus®, the decoders log in fully automatically to a suitable digital center. It masters all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable control panels. Auxiliary registers exist for control panels that can only program the CVs from 1-255. The LokPilot 5 Basic Decoder detects the Märklin® brake distances as well as the Lenz® ABC system. Braking with DCC brake blocks or dc voltage is also possible.The LokPilot 5 Basic Decoder can be used on analog DC webs. The maximum speed can be set separately.The decoder switches "on-the-fly" fully automatically between operating modes. Most of the time, nothing needs to be adjusted. Functions The LokPilot 5 Basic has 4 reinforced function outputs in each version. In the 21MTC interface, there are 8 logic-level outputs at the interface, two of which are also suitable for controlling servos. All important lighting functions are available. The brightness of each output can be set separately. Motor The motor control of the LokPilot 5 Basic delivers up to 0.9A continuous current. A variable PWM clock frequency from 10kHz to 50kHz ensures super-quiet operation, especially for bell anchor motors – The typical "hum" is a thing of the past. The load control can be adapted to difficult cases with up to 10 CVs. The unique "Autotune" function allows the decoder to be automatically measured against the motor. Operational reliability On request, a PowerPack can be connected to the LokPilot 5 Basic to bridge dirty rail cuts. Protection Of course, all function outputs as well as the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Art.No. Delivery 59020 LokPilot 5 Basic, 8-pin NEM652, Gauge H0, 0 59029 LokPilot 5 Basic, 21MTC NEM660, Gauge H0, 0

Selling price: CHF 27.50 RRP CHF 28.90

In stock: 1 on the shelf, shipped within 1-3 days

LokPilot 5 Fx DCC PluX22 NEMV NEM658 H0 0
ESU 59222
LokPilot 5 Fx DCC PluX22 NEMV NEM658 H0 0

LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 The LokPilot 5 Fx DCC is a function decoder with NO MOTOR CONTROL and is therefore perfect for installation in control cars (Cab Cars) or rail vehicles that only need lights and/or lighting effects. As the "twin brother" of the LokPilot 5 Fx, it shares its features and the basic characteristics of all other LokPilot 5 decoders, but is a pure DCC decoder. The LokPilot 5 Fx DCC is supplied in three versions: In addition to the "classic" version with 8-pin NEM 652 wiring harness, a version for the 21MTC interface and a PluX22 interface is also available. Operating Modes The LokPilot 5 Fx DCC is a pure DCC decoder. 14 to 128 speed steps are as standard as short (1-127) and long (128-9999) addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders register fully automatically with a suitable digital command station such as an ESU ECoS or CabControl. It supports all DCC programming modes and thanks to RailCom® the CV values can be read out on the main track with suitable command stations such as those from ESU. Auxiliary CVs exist for command stations that can only program the CVs from 1-255. The LokPilot 5 Fx DCC decoder detects the Märklin® brake distances as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with DC voltage is also possible. It also stops with a Selectrix® brake diode. An automatic ABC shuttle train system enables automatic shuttle operation between two stations. Although this decoder does not have motor control, it is important for the decoder to be able to synchronize non-motorized rail vehicles with those that are motorized. The LokPilot 5 Fx DCC decoder can be used on analog DC railways. The decoder switches between operating modes fully automatically "on-the-fly". In most cases, no adjustments are required. Functions The LokPilot 5 Fx DCC has been equipped with an astonishing number of function outputs. Depending on the interface version, each LokPilot 5 Fx DCC decoder offers at least 10 powered function outputs, each with a max output current of 250mA for lights. Versions with a PluX22 or 21MTC interface also feature 4 outputs for controlling servos or logic level outputs. All important lighting functions are available. The brightness of each output can be adjusted separately. Interaction The LokPilot 5 Fx DCC is designed to work with the LokSound 5 and the LokPilot 5 decoders: For example, it is possible to equip the locomotive of a multiple unit with a LokSound 5 decoder and the control car (Cab Car) with a LokPilot 5 Fx DCC. Provided they have the same address, both behave identically. The identical CV arrangement makes it easier to coordinate the two decoders. Operational reliability A PowerPack can be connected to the LokPilot 5 Fx DCC to bridge dirty track sections. Protection The outputs are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Technical Specifications Operating Modes: NMRA/DCC with 14, 28, and 128 speed steps, DCC RailCom® DCC 2-digit and 4-digit addresses (short and long addresses) Analog DC voltage (can be switched off). Automatic detection of operating mode and DCC speed step setting Support for Lenz® LG100, Märklin®, Roco® braking sections, and ZIMO® HLU commands Support for ABC braking mode and ABC shuttle train section Wrong-way bit / saving operating states Shunting mode and acceleration and braking delay can be switched via button Speed ​​controller: NO MOTOR CONTROL Function outputs: 10 powered function outputs Version with 21MTC interface has 2 additional logic level outputs and 2 further logic level outputs instead of SUSI Version with PluX22 interface has 2 logic level outputs instead of SUSI 250mA load capacity per powered output Total current of all function outputs approx. 1500mA. Short-circuit-proof outputs Functional output assignments freely selectable (function mapping) Dimensions: 16.5 mm x 15.5 mm x 4.5 mm Instruction manual Art.No. Delivery 59220 LokPilot 5 Fx DCC, 8-pin NEM652, »NO MOTOR CONTROL« gauge H0, 0 59222 LokPilot 5 Fx DCC, PluX22 NEM658, »NO MOTOR CONTROL« gauge H0, 0 59229 LokPilot 5 Fx DCC, 21MTC NEM660, »NO MOTOR CONTROL« gauge H0, 0

Regular price: CHF 26.90

In stock: 1 on the shelf, shipped within 1-3 days

LokPilot 5 DCC, 6-pin NEM651, gauge H0, 0
ESU 59626
LokPilot 5 DCC, 6-pin NEM651, gauge H0, 0

LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 The LokPilot 5 DCC is the "twin brother" of the LokPilot 5. The two share almost all characteristics, however, the LokPilot 5 DCC is a pure DCC decoder and cannot be used on analog AC systems. This lack of flexibility comes with a cheaper price. LokPilot 5 decoders are offered with all common interfaces. Modes The LokPilot 5 DCC is a "pure-bred" DCC decoder. 14 to 128 speed steps are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus® the decoders register automatically with a suitable DCC system like the ESU CabControl. The decoder accepts all DCC programming modes and thanks to RailCom® the CV values ​​can be read on the main track with RailCom equipped DCC systems. For command stations that only program the CVs from 1-255 auxiliary CV registers exist. The LokPilot 5 DCC decoder recognizes the Märklin® braking sections as well as the ZIMO® HLU / ZACKCommands or the Lenz® ABC system. Also braking with DCC brake modules or with DC voltageis possible. It also stops with a Selectrix® brake diode. An ABC automatic shuttle trainenables automatic commuting between two train stations. The LokPilot 5 DCC decoder can be used on analog DC trains. The top speedcan be set separately. The decoder switches between the operating modes fully automatically "on-the-fly". Features We know that you want your locomotives to be as realistic as possible. Therefore we have the LokPilot 5DCC packed with function outputs. Depending on the interface version, each LokPilot offers 5 DCCDecoder at least 10 amplified function outputs with 250mA output current each. In the executionswith PluX22 or 21MTC interface there are 4 outputs to control servos orLogic level outputs added. All-important lighting functions are available. The brightness of each outputcan be set separately. The decoder masters automatic pushing and pullingwhen uncoupling for ROCO®, Krois® and Telex® couplings. Motor control The engine control of the LokPilot 5 DCC has been fundamentally improved again. A variably adjustablePWM clock frequency from 10kHz to 50kHz ensures super quiet operation, especially with bell-armature motors.Operation - The typical “hum” is a thing of the past. The load control now has up to10 CVs  which can be adjusted for difficult cases. The unique "Autotune" function enablesthe automatic calibration of the decoder to the motor. The LokPilot 5 DCC decoder delivers up to 1.5A of motor current. Enough juice even for older motors. Operational safety On request, a PowerPack can be fitted to the LokPilot 5 DCC to bridge dirty rail sections. Protection Of course, all function outputs and the motor output are protected against overload. We want you to enjoy your decoder for as long as possible. Click the image for a bigger view. Betriebsarten: NMRA/DCC mit 14, 28 und 128 Fahrstufen, DCC RailCom® DCC 2-stellige und 4-stellige Adressen (kurze und lange Adressen) Analog Gleichspannung (abschaltbar). Automatische Erkennung der Betriebsart und DCC-Fahrstufeneinstellung Unterstützung der Lenz® LG100, Märklin®, Roco® Bremsstrecken und ZIMO® HLU Befehle Unterstützung für ABC Bremsmodus und ABC-Pendelzugstrecke Falschfahrbit / Speicherung der Betriebszustände Rangiergang und Anfahr- und Bremsverzögerung per Taste schaltbar Fahrtreglerteil: 2,0 A Dauerbelastbarkeit Anschluss von Gleichstrom- Glockenanker- und Wechselstrommotoren (mit Permanentmagnet) Geräuschlose, motorschonende Ansteuerung mit bis zu 50 kHz Taktfrequenz Motorausgang gegen Überlast geschützt. Lastregelung der 5. Generation (abschaltbar) Funktionsausgänge: 10 verstärkte Funktionsausgänge Version mit 21MTC-Schnittstelle zusätzlich 2 Logiklevelausgänge sowie 2 weitere Logiklevelausgänge statt SUSI Version mit PluX22-Schnittstelle 2 Logiklevelausgänge statt SUSI 250mA Belastbarkeit pro verstärktem Ausgang Summenstrom aller Funktionsausgänge ca. 500mA. Ausgänge kurzschlussfest Belegung der Funktionsausgänge frei wählbar (function mapping) Dimensionen: 21,4mm x 15,5mm x 4,5mm Instruction manual Art.No. Delivery 59620 LokPilot 5 DCC, 8-pin NEM652, gauge H0 ,0 59622 LokPilot 5 DCC, PLUX22 NEM658, gauge H0 ,0 59626 LokPilot 5 DCC, 6-pin NEM651, gauge H0 ,0 59629 LokPilot 5 DCC, 21MTC NEM660, gauge H0 ,0 59659 LokPilot 5 DCC, 21MTC MKL, gauge H0 ,0

Selling price: CHF 37.90 RRP CHF 38.90

In stock: 1 on the shelf, shipped within 1-3 days

LocoNet Cable 2,0 m
Faller 161392 Scale H0
LocoNet Cable 2,0 m

Modular cable, RJ12 plug to RJ12 plug, 6 wires, all assigned, 1:1, length: 2 m. Connection cable for all common LocoNet modules.

Regular price: CHF 6.40

In stock: 1 on the shelf, shipped within 1-3 days

5 self-flashing LEDs, blue
Faller 163742 Scale H0
5 self-flashing LEDs, blue

Eye-catcher! Light-emitting diodes with built-in microcircuit, to be used wherever a flashing lamp is required, e. g. as a visual signal on stationary models of vehicles (police, rescue service, fire brigade, construction industry, municipal companies, or agriculture), during gate opening and shutting movements, for the illumination of funfair models, and many others more. Supply voltage: 3-4 V DC Current input: up to 20 mA Flashing rate: approx. 1.5 Hz International component size: 0805 Length: 2 mm Width: 1.25 mm Height: 1.1 mm Advice: For lighting effects on Car System vehicles, use the Flashing lights, Art. 163760 to 163765.

Regular price: CHF 4.50

In stock: 1 on the shelf, shipped within 1-3 days

Assorted stranded wires 0.04 mm², 10 colours 10 m each
Faller 163780 Scale H0
Assorted stranded wires 0.04 mm², 10 colours 10 m each

Gauge: H0, N, TT, Z Cross-section: 0.04 mm² Contents: stranded wire in 10 colours, 10 m each

Selling price: CHF 24.90 RRP CHF 25.90

In stock: 1 on the shelf, shipped within 1-3 days

LED path light, warm white, 3 units
Faller 180136 Scale H0
LED path light, warm white, 3 units

Model of a modern path light. The filigree design of this lamp has a special charm. This makes it particularly suitable for illuminating paths, parks and gardens. The pedestal light is equipped with long-lasting LED technology. Height: 15 mm. Light colour: warm white. The product is ready for connection for 12 V, direct voltage (DC). Use the transformer, Art. 180699, to operate the light.

Selling price: CHF 19.90 RRP CHF 20.90

In stock: 1 on the shelf, shipped within 1-3 days

LED path light, silver, warm white, 3 pieces
Faller 180139 Scale H0
LED path light, silver, warm white, 3 pieces

Model of a modern path light. The filigree design of this lamp has a special charm. This makes it particularly suitable for illuminating paths, parks and gardens. The pedestal light is equipped with long-life LED technology. Height: 16 mm. Light colour: warm white. The product is ready for connection for 12 V, direct voltage (DC). Use the transformer, Art. 180699, to operate the light.

Selling price: CHF 19.90 RRP CHF 20.90

In stock: 1 on the shelf, shipped within 1-3 days

5 LEDs, in different colours
Faller 180652 Scale H0
5 LEDs, in different colours

LEDs with enamelled copper wires. Ready for connection to 12-16 V, AC/DC voltage. Pressure-sensitive. To illuminate buildings, rooms, means of advertising, outdoor installations, etc. In AC voltage mode you need rectifier (art. 180633) for flicker-free operation.

Selling price: CHF 20.90 RRP CHF 21.90

In stock: 1 on the shelf, shipped within 1-3 days

Platform lighting LED
Faller 180659 Scale H0
Platform lighting LED

180 mm, cold white, for lighting purposes, universal usage. Ready for connection, 12-16 V, AC/DC voltage. Suitable for many platform halls (e.g. art. 120180) and platforms (e.g. art. 120187, 120188, 120191). For flicker-free operation with alternating voltage, you will need the rectifier (art. 180633).

Selling price: CHF 23.90 RRP CHF 24.90

In stock: 1 on the shelf, shipped within 1-3 days

Lighting base
Faller 180670
Lighting base

Complete with quality bulb, 12–16 V, DC/AC voltage, 55 mA, cable, E 5.5 mm, Ø 8 mm base.

Regular price: CHF 1.50

In stock: 1 on the shelf, shipped within 1-3 days

Mini lighting effects welding light
Faller 180698 Scale H0
Mini lighting effects welding light

Welding light: very cold, bluish light. Maximum brightness. Short sequences of flashes of different intensities followed by pauses of varying lengths, e.g. 5 flashes with different brightnesses within 1 sec, then 5 sec pause, then similar flash sequence and 8 sec pause, etc.

Selling price: CHF 20.90 RRP CHF 21.90

In stock: 1 on the shelf, shipped within 1-3 days

Ambient mini-lighting effects
Faller 180712
Ambient mini-lighting effects

This light effect creates particularly atmospheric lighting conditions with its soft transitions and slow colour changes. It is equally suitable for illuminating a building (e.g. a castle or a facade) as for the effective lighting of a complete diorama.

Regular price: CHF 19.90

In stock: 1 on the shelf, shipped within 1-3 days

Geared motor
Faller 180722 Scale H0
Geared motor

Long-lasting geared motor characterized by its uniform run and its high torque, can be used e.g. to drive funfair models you have built yourself. The »D« shaft of that motor is equivalent to the »D« shaft of FALLER synchronous modeller’s motor, Art. 180629, so that the latter can also be replaced by the former with some manual dexterity. The geared motor may be operated with a maximum voltage of 5 V DC and reaches a speed of up to approx. 90 RPM.

Selling price: CHF 26.90 RRP CHF 27.90

In stock: 1 on the shelf, shipped within 1-3 days

12% off the recommended price
DCC-Decoder 6-pin
Fleischmann 685404
DCC-Decoder 6-pin

Suitable for Gauge H0e, TT and N. The decoder is equipped with the RailCom function. Maximum motor current: 0.8 A. Wire length: approx. 30 mm. For further technical specification, see the spec sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. Answers to possible questions can be found in this Zimo manual

Selling price: CHF 40.90 RRP CHF 46.90

In stock: 1 on the shelf, shipped within 1-3 days

11% off the recommended price
Decoder NEM651
Fleischmann 686101
Decoder NEM651

Suitable for Gauge H0e, TT and N. The decoder is equipped with the RailCom function. Maximum motor current: 0.8 A. For further technical data see data sheet. (Downloads) RailCom is a registered trademark of Lenz Elektronik GmbH, Gießen. Answers to possible questions can be found in this Zimo manual

Selling price: CHF 36.90 RRP CHF 41.90

In stock: 1 on the shelf, shipped within 1-3 days

DCC decoder without plug (N gauge)
Fleischmann 696859 Scale N
DCC decoder without plug (N gauge)

Digital locomotive decoder to NMRA DCC standard for N gauge, version without plug connector with connecting leads for retrofitting DC locomotives without an interface. Supports 14/28/128 speed steps, function mapping (CV 33/34) and load regulation. Predecessor of the current decoder 69685401.

Regular price: CHF 44.90

In stock: 1 on the shelf, shipped within 1-3 days

13% off the recommended price
Feeder clip 2x1 pole
Fleischmann 9400 Scale N
Feeder clip 2x1 pole

single track feed clips.

Selling price: CHF 6.00 RRP CHF 6.90

In stock: 1 on the shelf, shipped within 1-3 days

14% off the recommended price
Activating Magnet
LGB 17010 Scale G
Activating Magnet

Triggers the LGB 17100 track contact. Simply mount it under LGB locomotives.

Selling price: CHF 7.40 RRP CHF 8.69

In stock: 1 on the shelf, shipped within 1-3 days

10% off the recommended price
36 Watt Switched Mode Power P
LGB 51090 Scale G
36 Watt Switched Mode Power P

Weatherproof (IP 67) switched-mode power supply for supplying the 51099 controller with power. Use with 51099.

Selling price: CHF 70.00 RRP CHF 77.99

In stock: 1 on the shelf, shipped within 1-3 days