Digital electronics and H0 locomotives
ESU, LokSound sound and the SBB Ae 6/6 in H0
LokSound sound decoders, LokPilot decoders, the ECoS command station, the Mobile Control Pro throttle and SwitchPilot accessory decoders: ESU, based in Neu-Ulm, equips your digital layout from locomotive to turnout, and builds sound-fitted H0 locomotives such as the SBB Ae 6/6.
- 245items in the shop
- Since 1999LokSound sound decoders
- 4 protocolsDCC, Motorola, Selectrix and M4

What ESU brings to your layout
- The SBB Ae 6/6 in H0: metal body structure and frame, digitally raised and lowered pantographs, original Ae 6/6 sounds on a LokSound 5 decoder and two speakers. A plug-in pickup and a switch for two-rail or three-rail running.
- LokSound 5, sound since 1999: up to 10 sound channels at once, at least 10 amplified outputs, DCC, Motorola, Selectrix and M4, and automatic registration with the command station via RailComPlus.
- LokPilot 5 for driving: the same four protocols plus analogue running, at least 10 function outputs of 250 mA, load control adjustable through up to 10 CVs.
- From control desk to turnout: ECoS command station with a 7-inch touchscreen, the wireless Mobile Control Pro throttle, also for Z21 and CS3, and SwitchPilot 3 for turnouts, colour-light signals and up to eight servos.
The ESU families
For your H0 layout (1:87)
5 itemsSBB locomotivesThe Ae 6/6 'Uri', 'Ticino', 'Glarus' and 'Lausanne', plus an SBB Cargo.See the items
23 itemsLocomotives H0DB electric and diesel locomotives, Class 66 and KG230 shunters.See the items
25 itemsCoaches and wagons H0DB n-coaches and Sgmmns container wagons.See the itemsTo control your layout and give it sound
25 itemsLokSound sound decodersLokSound 5, from micro and Nano up to L and XL.See the items
40 itemsLokPilot decodersLokPilot 5 for driving, plus the Fx function decoders.See the items
13 itemsECoS and Mobile ControlECoS command station and modules, Mobile Control Pro throttle, CabControl.See the items
13 itemsSwitchPilot and servosTurnout and signal decoders, servo motors and extensions.See the items
31 itemsSpeakersRound and rectangular speakers for sound decoders.See the itemsAll ESU items
Speaker 24mm x 55mm x 8.6mm, square, 8 Ohm, Passive Radiator This loudspeaker module is suitable for large tenders with gauge H0 or OO or models with gauge 0. Its built-in passive radiator, in conjunction with the built-in broadband speaker, results in good bass reproduction without neglecting the highs and mids. Especially for diesel or steam locomotives, this module is a real alternative for those who like deep bass but don't need extreme volume. The speaker fits perfectly with our LokSound 5 or LokSound 5 L decoders. Art.No. Delivery 50344 Speaker 24mm x 55mm x 8.6mm, square, 4 Ohm, Passive Radiator 50346 Speaker 24mm x 55mm x 8.6mm, square, 8 Ohm, Passive Radiator
On order, shipped within 4-5 days
Speaker 22mm x 42mm x 8.0mm, square, 8 Ohm, Passive Radiator This new speaker module fits wherever 20mm x 40mm rectangular speakers were previously installed. With the help of the built-in passive radiator in conjunction with a high-performance rectangular speaker, the module achieves significantly improved bass reproduction and achieves a considerable sound pressure even in the highs and mids. The module is particularly suitable for diesel or steam locomotives where contemporary bass reproduction is important. The speaker fits perfectly with our LokSound 5 micro, LokSound 5 or LokSound 5 L decoders. Art.No. Delivery 50345 Speaker 22mm x 42mm x 8.0mm, square, 4 Ohm, Passive Radiator 50347 Speaker 22mm x 42mm x 8.0mm, square, 8 Ohm, Passive Radiator
On order, shipped within 4-5 days
Speaker 18mm x 35mm x 11mm, rechteckig, 4 Ohm, Passive Radiator This speaker module offers extremely good performance data with moderate dimensions. With the help of the built-in passive radiator in conjunction with a high-performance rectangular speaker, the module achieves high quality bass reproduction and achieves a considerable sound pressure even in the highs and mids. The module is particularly suitable for diesel or steam locomotives where contemporary bass reproduction is important. The speaker fits perfectly with our LokSound 5 micro, LokSound 5 or LokSound 5 L decoders. Art.No. Delivery 50348 Speaker 18mm x 35mm x 11mm, rechteckig, 4 Ohm, Passive Radiator
On order, shipped within 4-5 days
Speaker D=28mm x 11mm, round, 4 Ohm, Passive Radiator This round speaker module can replace a regular 28mm round speaker in most cases. With the help of the built-in passive radiator in conjunction with a high-performance rectangular speaker, the module achieves high quality bass reproduction and achieves a considerable sound pressure even in the highs and mids. The module is particularly suitable for diesel or steam locomotives where contemporary bass reproduction is important. The speaker fits perfectly with our LokSound 5 micro, LokSound 5 or LokSound 5 L decoders. Art.No. Delivery 50349 Speaker D=28mm x 11mm, round, 4 Ohm, Passive Radiator
On order, shipped within 4-5 days
This speaker module offers extremely good performance data with moderate dimensions. With the help of the built-in passive radiator in conjunction with a high-performance rectangular speaker, the module achieves high quality bass reproduction and achieves a considerable sound pressure even in the highs and mids. It was specially developed for American Scaletrains (SXT) diesel locomotives as a replacement for the factory-fitted speakers: It fits without adapting the locomotive. The speaker fits perfectly with our LokSound 5 decoders.
On order, lead time to be confirmed
For difficult installation situations with little available space, especially in N-gauge, we recommend our miniature loudspeaker with a footprint of just 10mm x 12mm. This speaker was selected by our audio engineers after extensive testing because it offers a good compromise between acceptable bass reproduction and volume. This ‘dwarf’ produces an astonishingly high sound pressure level - when combined with the appropriate sound chamber. The set includes four sound chambers of different heights, resulting in a total height (with mounted speaker) of 11mm, 8mm, 6mm or 5mm. Choose the largest sound capsule that you can accommodate. Adhesive tape is provided on the speaker itself for simple, airtight mounting. The solder connection is made via a short piece of flexible printed circuit board.
On order, shipped within 4-5 days
At 13mm x 18mm, this new ‘sugar cube’ loudspeaker is larger than the speaker previously known from ESU. As the diaphragm is therefore a good 40% larger, it can produce significantly higher sound pressure levels. Bass, midrange, and treble reproduction are flawless. This speaker can be used anywhere our bass reflex speakers don't have space, but where the best possible bass reproduction is still important. The same applies to our new speaker: the larger the sound chamber, the better the sound. We supply 4 sound chambers of different heights in the set. With the speaker mounted (hermetically sealed!), the total height is 17.5mm, 12.5mm, 9.5mm or 7.5mm.
On order, lead time to be confirmed
Loudspeaker 40mm, round, 100 Ohm, with sound chamber For the well-proven LokSound V3.5, LokSound micro V3.5 and LokSound V3.0 M4 decoders we offer loudspeakers in the following sizes: 2x13mm (50 Ohms each), 2x16mm (50 Ohms each), 16x25mmm, 20mm, 23mm, 28mm, 20x40mm and 40mm. By virtue of the internal design of the decoders, the speakers feature a specially customised impedance of 100 Ohms. Only these speakers may be used! Art.No. 50335 Loudspeaker 32mm, rund, 100 Ohm, without sound chamber Expires 50442 Loudspeaker 23mm, round, 100 Ohm, with sound chamber Expires 50444 Loudspeaker 40mm, round, 100 Ohm, with sound chamber Expires 50447 Two loudspeakers 16mm, oval, je 50 Ohm, with sound chamber Expires 50448 Loudspeaker 20mm x 40mm, square, 100 Ohm, with sound chamber Expires
On order, lead time to be confirmed
Loudspeaker 78mm, round, 8-32 Ohms, with sound chamber decoders work with loud speakers which have an impendance from 8-32 Ohms. ESU offers you a selection of the sizes 40mm, 57mm and 78mm includung sound chamber as well as some high-class Visation XL loudspeakers without sound chamber. Visaton loudspeakers offer a powerful bass and a high-quality audio playback, whereas ESU loudspeakers are also suitable for open-land vehicles due to their plastic membrane. 50336 50336 50337 50337 50446 Part No. 50322 Loudspeaker Monacor Sp6/4SQ, 59mm, round, 8 Ohms, for PIKO G/LGB Loks 50323 Loudspeaker 40mm round, 8 Ohms, with sound chamber for LokSound H0, LokSound XL 50324 Loudspeaker Visaton FRS 7, 70mm, round, 8 Ohms 50336 Loudspeaker Visaton SC4.7ND, 41x70mm, square, 8 Ohms 50337 Loudspeaker Visaton FRS5, 50mm, round 8 Ohms 50446 Loudspeaker 78mm, round, 8-32 Ohms, with sound chamber Expires
On order, shipped within 4-5 days
Loudspeaker 20mm x 40mm, square, 100 Ohm, with sound chamber For the well-proven LokSound V3.5, LokSound micro V3.5 and LokSound V3.0 M4 decoders we offer loudspeakers in the following sizes: 2x13mm (50 Ohms each), 2x16mm (50 Ohms each), 16x25mmm, 20mm, 23mm, 28mm, 20x40mm and 40mm. By virtue of the internal design of the decoders, the speakers feature a specially customised impedance of 100 Ohms. Only these speakers may be used! Art.No. 50335 Loudspeaker 32mm, rund, 100 Ohm, without sound chamber Expires 50442 Loudspeaker 23mm, round, 100 Ohm, with sound chamber Expires 50444 Loudspeaker 40mm, round, 100 Ohm, with sound chamber Expires 50447 Two loudspeakers 16mm, oval, je 50 Ohm, with sound chamber Expires 50448 Loudspeaker 20mm x 40mm, square, 100 Ohm, with sound chamber Expires
On order, lead time to be confirmed
LED lighting strip with taillight, 255mm, 11 LEDs, „warm-white“. For gauge N,TT, H0 The 255mm long, 9mm slim LED lighting strips with 11 LEDs are designed for N, TT and H0 gauge cars. We are offering two versions: The version with Part number 50700 is equipped with warmwhite LEDs, while on part number 50702 we installed yellow LEDs. This will give you the choice to match the lighting strips with your existing cars. As usual for all ESU lighting strips, you can adjust the brightness according to your wishes with the help of a small variable resistor (potentiometer). Thanks to built-in voltage control the brightness remains almost constant even when conventional driving. To bridge prolonged power interruptions, you may add a PowerPack. Of course, the lighting strips can be arbitrarily cut to fit the cars of all manufacturers and comes with a red taillight. You may add a LokPilot Fx V4.0 function decoder at any time. Part No. 50700 LED lighting strip with taillight, 255mm, 11 LEDs, „warm-white“. For gauge N,TT, H0 50702 LED lighting strip with taillight, 255mm, 11 LEDs, „yellow“. For gauge N,TT, H0
On order, shipped within 4-5 days
LED lighting, current collector (Wheel contact) for waggons N / H0, 8-piece set, gauge: N, TT, H0 Our current pick-ups (50707) provide optimal electrical contact in all commercially available coaches and are easy to install: simply glue them to the underside of the bogie so that the pre-tensioned contact strips touch the inside of the wheels (wheel flange). Since each set consists of two sprung contact strips one set per axle is enough. Suitable for any axle spacing. Suitable for H0 DC and AC or N gauge. Set with 8 current pick-up contacts sufficient for 8 axles. The new PowerPack super capacitor may be connected to our coach lighting modules 50700, 50702, 50708 and 50709 and reliably prevents any flicker in case of poor contact. Despite the fact that it is more compact than its predecessor it has twice the capacity (0.22F/5.5V). Please note that the PowerPack 50710 is designed for use with the interiour light strips only. It can not be used to buffer decoders! Part No. Delivery 50710 LED lighting strip, PowerPack energy storage, 0,22F, double pack 50707 LED lighting, current collector (Wheel contact) for waggons N / H0, 8-piece set, gauge: N, TT, H0
On order, shipped within 4-5 days
LED lighting strip, PowerPack energy storage, 0,22F, double pack Our current pick-ups (50707) provide optimal electrical contact in all commercially available coaches and are easy to install: simply glue them to the underside of the bogie so that the pre-tensioned contact strips touch the inside of the wheels (wheel flange). Since each set consists of two sprung contact strips one set per axle is enough. Suitable for any axle spacing. Suitable for H0 DC and AC or N gauge. Set with 8 current pick-up contacts sufficient for 8 axles. The new PowerPack super capacitor may be connected to our coach lighting modules 50700, 50702, 50708 and 50709 and reliably prevents any flicker in case of poor contact. Despite the fact that it is more compact than its predecessor it has twice the capacity (0.22F/5.5V). Please note that the PowerPack 50710 is designed for use with the interiour light strips only. It can not be used to buffer decoders! Part No. Delivery 50710 LED lighting strip, PowerPack energy storage, 0,22F, double pack 50707 LED lighting, current collector (Wheel contact) for waggons N / H0, 8-piece set, gauge: N, TT, H0
On order, shipped within 4-5 days
Interiour lighting set with decoder, Entry+Red marker light, 264mm, divisible, PowerPack Option, 13 LED, yellow With the digital LED interior lights from ESU, you can retrofit your N, TT or H0 gauge passenger cars with prototypical, uniform lighting. Two versions are available to suit the desired location. The digital interior lights are 264mm long, 9mm slim and each fitted with 13 (!) LEDs. In addition to a version with warm white LEDs (50718), there is also a board with yellow LEDs (50719) so that the light color always matches your existing wagons. Features The digital interior lighting consists of a 74 mm long base section, on which a digital decoder and four LEDs are mounted, and eight adjoining sections, each equipped with one LED spaced 24mm apart. The additional sections can be cut off to customize the length to suit the wagon. Furthermore, two additional 4.5mm wide, detachable LED sections are provided on the far left and right sides to illuminate the entry area. The brightness of the LEDs can be set either using a potentiometer or via software CV and remains constant regardless of the track voltage thanks to the built-in constant voltage supply. A built-in buffer capacitor bridges small current interruptions ex works. To completely prevent flickering even with poor power pickup, a special, very compact PowerPack supercapacitor (ESU item no. 50710) can be connected directly upon request. This can power the LEDs for a few seconds. The digital interior lighting comes with a soldered red tail light. Operating modes The decoder, based on the LokPilot 5 Basic and adapted to the intended use, supports the DCC and Märklin® Motorola® protocols. It can handle 2- and 4-digit addresses and can trigger functions up to F31. Thanks to RailComPlus®, the decoders register fully automatically with a suitable DCC command station. It supports all DCC programming modes, and thanks to RailCom®, the CV values can be read on the main track with suitable command stations. Auxiliary registers are available for command stations that can only program CVs 1-255. Alternatively, the decoder can be read on the programming track without an additional load resistor. The digital interior lighting can also be used on analog AC and DC systems. In both operating modes, the direction of travel is correctly detected and the tail light is switched accordingly. Functions The 13 built-in LEDs can be individually controlled in a total of seven groups: The two entrance LEDs can each be switched separately. The tail light can also be switched separately depending on the direction of travel. Furthermore, there is an amplified output and two outputs for connecting additional LEDs (e.g., for headlights on Pilot cars or toilet lighting), which can be wired individually. Various prototypical lighting effects such as soft dimming, neon tube effects, defective neon tubes, battery lighting, and much more ensure a realistic result. The ESU V5 Function Mapping allows the individual assignment of all LED groups to the desired function keys. Robust You can rely on the experience and quality of a renowned brand manufacturer, even when it comes to digital interior lighting.
On order, shipped within 4-5 days
Servo Motor, precision mini-servo, micro-controlled with plastic gearing, incl. mounting kit The Precision Servo Motor is a high-performance and noiseless actuator, introduced by ESU, suitable for the SwitchPilot decoders. It uses a highly-developed remote control (RC) technique and is perfectly suited for setting in motion all kinds of scenes on your layout. ESU has put all the experience gained with the previous servo motor into the new Precision version, which is better than other servo products, to offer a solution for all the demands of model railroaders. Applications The most important application regarding the Precision Servo Motor is to throw points. With the help of the Precision Servo Motor you are able to move your model railway switches like the original ones: the switch blade moves slowly and powerfully from one position to another. While doing this the Precision Servo motor works almost noiselessly due to the precision gearing made of long-lasting plastic. It is mere child´s play to motorize railway crossings via the Precision Servo motor and the SwitchPilot Servo. At last you can let the gates down at your keyboard in due time. Furthermore the Servo motor enables you to open and close the doors of your engine shed by remote control. Thanks to its new electronics the ESU Precision Servo Motor moves considerably smoother than other servos, as the ESU product has been optimized for slow motions. Mini servo The most important component of the Precision Servo Motor is a tiny, 9-gram-light mini servo which has been specially developed and optimized for all demands of a model railway layout. Despite its small dimensions of only 26 mm x 13 mm x 24 mm, it reaches a power of up to 1.0 kg/cm. Its cable length of 30cm (almost twice as long as cables of other standard servos on the market) allows for a longer distance between the servo motor and decoder. Beyond that, an electronic processor-controlled servo enables a precise heading for the required position without bucking - very important for garage doors. The closed current requirements of the electronics have been mottled compared to the previous servo motor which preserves the decoder. However, one of the most important improvements of the new Precision Servo Motor has to do with the switching-on: The well-known tremor when switching on the layout, which occurs with a lot of conventional RC-servos, is 100% choked during every operation mode. You will hear absolutely nothing from the servo when switching your layout on, no railway crossing will bounce. To make the application of the Servo motor as easy as possible, we include substantial accessories with delivery, which are especially adjusted to our customers´ needs: among some, diverse control horns, there is a special servo horn for a direct insert of the controlling wire. The controlling wire is, of course, included as well as the mounting screws. The most important accessory is a special servo holder: it enables you to install the Servo Motor either horizontally or vertically - depending on the application. Art.No. 51804 Servo Motor, precision mini-servo, micro-controlled with plastic gearing, incl. mounting kit
On order, shipped within 4-5 days
Linear Servo, movement 4.5 mm, with microcontroller, 30cm wire,with fittings accessories This linear servo with dimensions 26mm x 22.5mm x 10.8mm is primarily intended for installation in electric locomotives in order to subsequently make the pantographs raised and lowered. The mechanics enable very quiet, smooth running and avoid the noise produced by commercially available servos. The servos radius of movement is approx. 4.5 mm. As is usual with ESU servos, the electronics have been optimized for use in model railway systems: the “start-up twitching” has been eliminated, as has the “humming” under load. The servo can be controlled either with LokSound 5 or LokPilot 5 decoders (both decoders generate the required control impulse) or alternatively used at your own discretion on a model railway system to switch switches or gates. In this case we recommend the SwitchPilot Servo for control.
On order, shipped within 4-5 days
SwitchPilot Extension Adapter for ABC brake sections. Set of 2 for 4 brake sections These adaptor boards greatly simplify set-up and wiring of ABC braking sections. They are simply plugged into the terminals of a SwitchPilot Extension. Every adaptor board can generate the signals for two braking sectors and are wired as shown in the picture. ABC braking works reliably with all ESU V4 decoders (and others) and facilitates not just a prototypical slow down ahead of a red signal but also allows for triggering functions while waiting for the signal aspect to change. Any sound effects are also maintained.
On order, shipped within 4-5 days
SwitchPilot Adapter for Signals with common cathode. Set of 2 for 8 Outputs Our SwitchPilot decoders cannot only control point mechanisms but also daylight signals. Most modern signals are equipped with LEDs. Usually the anode connections of multi-aspect signals are combined in order to reduce the number of wires. Some manufacturers (e.g.: Viessmann®) combine the cathodes and for that reason these signals could not be controlled with the SwitchPilot in the past. Our new adapter provides the solution. Simply plug the adapter into the output terminals of the SwitchPilot and you are ready to go.
On order, shipped within 4-5 days
Servo Extension Cable, 3-pole J/R plug on socket J/R / Futaba, Length: 75cm With the Servo Extension Cable you are able to lengthen your Precision Servo Motor by up to 75cm. Art.No. 51810 Servo Extension Cable, 3-pole J/R plug on socket J/R / Futaba, Length: 75cm
On order, shipped within 4-5 days
SwitchPilot 3, 4x accessory decoder, DCC/MM, OLED, with RC-Feedback, updatable SwitchPilot 3 decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption.In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons. Modes The SwitchPilot 3 is multi-protocol and can be used with workstations according to the Märklin® Motorola® system (e.g. 6021, Central Station® or Mobile Station®) as well as DCC-enabled control panels. The configuration can take place on both the main track and the programming track. Thanks to RailCom®, CVs can also be read out. Functioning The SwitchPilot 3 can be supplied directly from the digital system or from an external DC or change voltage source. It has a total of 8 transistor outputs, which are grouped in the 4 exit pairs 1 to 4. Each output pair contains two outputs (OutA and OutB) and can be configured individually for the desired use case:In pulse mode, the output is switched on as soon as a switching command is received. The fact that the output automatically switches off again as soon as the time stored in the decoder has elapsed prevents the burning of magnetic article drives.At the moment (K83-compatible) the output remains active as long as the button on the control panel is pressed. This operating mode is suitable for turnout drives with final shutdown or for de-caps.In bi-stable continuous operation (k84-compatible), the two outputs are switched on and off: When pressing the first button (red) on the control panel, the output Out A is switched on. It remains active until pressing the assigned button (green) activates the output Out B of the same output group. Out A and Out B behave like a change switch.In alternating flasher mode, the outputs Out A and Out B of an output pair are switched on alternately with an adjustable flashing frequency. The change indicator is started with the command "Ge- rade/Green" of the assigned button and stopped again with the command "Branching/Red".Optionally, the output can also be slowly dimmed and dimmed (so-called "zoom" for glow lam pen simulation).With the switch 3 mode switch, you can switch all output pairs together to the "k83" or "k84" modes at lightning speed, regardless of how they are configured. Feedback Since the SwitchPilot 3 is RailCom®-capable, all settings can be read out and changed directly in the built-in state on request. In combination with an ECoS as an ideal "partner", the SwitchPilot 3 can record and display the actual turnout setting with appropriately prepared turnout drives. Finally, you have the certainty that your switch has switched correctly! Set The SwitchPilot 3 can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom® CVs. On request, he also learns the addresses directly via a programming button. The easiest way to set is, of course, with the integrated OLED display and the three input buttons: All (!) Settings can be checked directly on the decoder and changed on request. A"Programming" with the help of your control panel is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 are largely protected against overload. We want you to enjoy your decoder for as long as possible.
On order, shipped within 4-5 days
SwitchPilot 3 Plus, 8x accessory decoder, DCC/MM, OLED, updatable SwitchPilot 3 Plus decoders are optimized for stationary use on your system and can switch conventional double coil switch drives, light signals, magnetic uncouplers, light bulbs or other stationary consumption. In order to facilitate the rather cumbersome configuration of magnetic article decoders, the SwitchPilot 3 Plus has an innovative operating concept consisting of a 4-line, illuminated OLED display and three input buttons. Modes The SwitchPilot 3 Plus is multi-protocol and can be used with control panels according to the Märklin® Motorola® system (e.g. 6021, Central Station® or Mobile Station®) as well as DCC-enabled control panels. The configuration can take place on both the main track and the programming track. Thanks to RailCom®, CVs can also be read out. Functioning The SwitchPilot 3 Plus can be supplied directly from the digital system or from an external DC or change voltage source. It has a total of 16 transistor outputs, which are grouped in the 8 exit pairs 1 to 8. Each output pair contains two outputs (OutA and OutB) and can be configured individually for the desired use case: In pulse mode, the output is switched on as soon as a switching command is received. Since the output automatically switches off again as soon as a time stored in the decoder has been reached, a burn-through of magnetic articles is prevented. At the moment (K83-compatible) the output remains active as long as the button on the control panel is pressed. This operating mode is suitable for turnout drives with final shutdown or for de-caps. In bi-stable continuous operation (k84-compatible), the two outputs are switched on and off: When pressing the first button (red) on the control panel, the output Out A is switched on. It remains active until pressing the assigned button (green) activates the output Out B of the same output group. Out A and Out B behave like a change switch.In alternating flasher mode, the outputs Out A and Out B of an output pair are switched on alternately with an adjustable flashing frequency. The change indicator is started with the command "Gerade/Green" of the assigned button and stopped again with the command "Branching/Red".Optionally, the output can also be slowly dimmed and dimmed (so-called "zoom" for incandescent lamp simulation). Set The SwitchPilot 3 Plus can be flexibly adjusted either on the programming track with DCC control panels or on the main track with POM ("Programming on Main") or can also be read out via RailCom® CVs. On request, he also learns the addresses directly via a programming button. The setting is, of course, the simplest with the integrated OLED displays as well as the three input buttons: All (!) Settings can be checked directly on the decoder and changed on request. "Programming" with the help of your headquarters is not required. It really can't be any easier. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 Plus are protected against overload. We want you to enjoy your decoder for as long as possible.
On order, shipped within 4-5 days
SwitchPilot 3 Mini, 1x accessory decoder, DCC/MM, OLED, updatable The compact SwitchPilot 3 Mini decoder is designed for stationary use in hard-to-reach areas of your layout and can control a double-coil turnout motor, two magnetic uncouplers, a two-aspect signal, two incandescent bulbs, or other stationary loads. The SwitchPilot 3 Mini features an innovative operating concept consisting of a 4-line, backlit OLED display and three input buttons. Operating Modes The SwitchPilot 3 Mini is multi-protocol compatible and can be used with command stations based on the Märklin® Motorola® system (e.g., 6021, Central Station®, or Mobile Station®) as well as DCC-compatible control units. Configuration can be performed on either the main track or the programming track. Functions The SwitchPilot 3 Mini can be powered either directly from the digital system or from an external DC or AC power source. It has a total of two transistor outputs. The outputs (OutA and OutB) can be individually configured for the desired application: In pulse mode, the output is switched on as soon as a switching command is received. The fact that the output switches off automatically once the time stored in the decoder has elapsed prevents solenoid drives from burning out. In momentary mode (K83-compatible), the output remains active as long as the button on the control panel is pressed. This operating mode is suitable for accessories with limit switches or for uncoupling tracks. In bistable continuous mode (K84-compatible), the two outputs are switched on and off alternately: Pressing the first button (red) on the control panel switches on output Out A. It remains active until the corresponding button (green) activates output Out B. Out A and Out B behave like a changeover switch. In alternating flashing mode, outputs Out A and Out B are switched on alternately at an adjustable flashing frequency. The alternating flasher is started with the "Straight/Green" command of the assigned button and stopped with the "Round/Red" command. Optionally, the output can also be slowly faded in and out (so-called "zoom" for incandescent bulb simulation). Setup The SwitchPilot 3 Mini can be flexibly set up either on the programming track with DCC command stations or on the main track with POM ("Programming on Main"). It can also learn addresses directly via a programming button. The easiest way to set it up, however, is with the integrated OLED display and the three input buttons: All settings can be checked and changed directly on the decoder. "Programming" using your command station is not required. It really couldn't be simpler. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 Mini are largely protected against overload. We want you to enjoy your decoder for as long as possible.
On order, lead time to be confirmed
SwitchPilot 3 Servo Mini, 1x servo decoder, DCC/MM, OLED, updatable The compact SwitchPilot 3 Servo Mini decoder is designed for stationary use in hard-to-reach areas of your layout and can control an RC servo drive. The SwitchPilot 3 Servo Mini features an innovative operating concept consisting of a 4-line, backlit OLED display and three input buttons. Operating Modes The SwitchPilot 3 Servo Mini is multi-protocol compatible and can be used with command stations based on the Märklin® Motorola® system (e.g., 6021, Central Station®, or Mobile Station®) as well as DCC-compatible control units. Configuration can be performed on both the main track and the programming track. Functions The SwitchPilot 3 Servo Mini can be powered either directly from the command station or from an external DC or AC power source. It has an RC servo output. It can control these drives so precisely that, in addition to switching turnouts, it can also control any other slow-moving sequences. The SwitchPilot 3 Servo Mini features built-in power-on pulse suppression to eliminate or reduce the inherent "jerking" of RC servos when power is applied. Furthermore, the power supply to the servo can be disabled to prevent the "humming" sound of some inexpensive servos. The servo can be operated in either "digital mode" or "proportional mode." In digital mode, the servo can move to two end positions, "A" and "B," depending on the switch position on the control panel. The position of these two end positions, as well as the speed at which the servo moves in the desired direction, can be individually adjusted on the SwitchPilot 3 Servo Mini. Digital mode is ideal for switching turnouts or signals that need to remain in a fixed position. In proportional mode, the servo can move to any position within the end positions "A" and "B" and can also stop. The servo only runs as long as the control panel sends a command. Releasing the button stops the servo. This allows you to stop a servo in any desired position. The servo speed can be individually adjusted. Proportional mode is ideal for (water) cranes, locomotive shed doors, or any other application that requires intermediate positions. For each servo, in addition to the end positions and rotation speeds, you can specify whether it should bounce after reaching the end position. Furthermore, to adapt to the various RC servos available on the market, the generation of the servo pulse can be adjusted. This allows for optimal control of inexpensive analog servos as well as modern digital servos (with microcontrollers). Analog Operation The SwitchPilot 3 Servo Mini can be used without a digital command station as a special feature: Two pushbuttons can be added as needed to control the servos directly. Setup The SwitchPilot 3 Servo Mini can be flexibly set up either on the programming track with DCC control units or on the main track with POM ("Programming on Main"). It can also learn addresses directly via a programming button. The easiest way to set it up, however, is with the integrated OLED display and the three input buttons: All settings can be checked and changed directly on the decoder. "Programming" via your control unit is not required. It really couldn't be simpler. The ESU LokProgrammer can be used for firmware updates. Protection As with our locomotive decoders, the outputs of the SwitchPilot 3 Servo Mini are largely protected against overload. We want you to enjoy your decoder for as long as possible.
On order, lead time to be confirmed
SignalPilot, accessory decoder with 16 outputs Push/Pull, Removable screw terminals The ESU SignalPilot decoder is a multi-protocol decoder designed primarily for switching daylight signals. It has 16 outputs to which micro lamps or LEDs (with series resistors) can be connected directly. Because all outputs are designed as push/pull output stages, both daylight signals with common anode as well as daylight signals with a common earth connection (common cathode) are suitable, as is the case with Viessmann® signals. Motorised semaphore signals and turnout drives can also be operated with the SignalPilot. Operating modes The SignalPilot supports both DCC with RailComPlus® and Motorola®. Programming allows for each output to be assigned to any address or to a combination of addresses. Functionality The SignalPilot can be powered either directly by the digital command station or by any transformer /power supply unit providing DC or AC. The SignalPilot has 16 transistor outputs in push-pull configuration. Each output can be operated individually as continuous light, flashing light or pulse light. Here, the brightness or flashing frequency can be adjusted as well as fade-in and fade-out times. Various prototypical lighting effects such as soft dimming, fluorescent tube effect, defective fluorescent tube, gas lantern simulation, flicker light ensure a realistic result. Randomly controlled switching on/off as well as an on/off delay can also be activated. A night service extension can dim down the outputs together if so desired. The outputs of the SignalPilot are combined into signal aspects during configuration. In principle, two-, three-, four- or multiaspect signals are conceivable. Depending on the number of outputs involved, one or more turnout numbers (accessory addresses) are assigned to each signal, with the help of which you can later switch the individual signal aspects. Up to 16 turnout numbers are available for this purpose. The configuration of the signal aspects is carried out exclusively with the aid of the ESU LokProgrammer software. You select the desired signal aspects, then write them to the decoder and finally wire the signals as configured. All signal aspects predefined in the LokProgrammer software can be changed individually. The description of the signal aspects themselves is done with the help of XML files, which on the one hand are regularly extended by ESU or can be created and extended by you at your own discretion. In this way, „exotic” signals can also be supported. The SignalPilot is multi-protocol capable and can be used with digital command stations operating the Märklin® Motorola® system (e.g.: 6021, Central Station® or Mobile Station®) as well as DCC enabled command stations. The configuration can be doen by Programming on the Main (POM) and on the programming track. Thanks to RailCom®, CVs can also be read out. Optionally, a SwitchPilot Extension relay module can be docked to the SignalPilot. This facilitates setting up brake chapters or turnout frog polarisation. LokProgrammer The easiest method of configuring the SignalPilot is programming it with the ESU LokProgrammer. Simply choose the desired signal type, and the wiring will be displayed on the screen. Designed with future developments in mind The firmware of the SignalPilot can be updated with the aid of the LokProgrammer at any time. This may be necessary whenever we add new signal types. Art.No. Delivery 51840 SignalPilot, accessory decoder with 16 outputs Push/Pull, Removable screw terminals
On order, shipped within 4-5 days